• other review refict

• review refict

• add promiscuous mode support

• delete option

• use same workaround as NetBSD

• add promiscuous mode support and cleanup

Mavell e6060 datasheet use SMI word. That is MDC/MDIO. But Infineon data sheet not use SMI work. Do I change "MDC/MDIO interface" from "SMI". I want say difference i2c or spi bus.

• same componet other mediatek config to avoid confusion

• forget debug comment out

• add CD9660

• add kernel build conf file

I saw NetBSD cfi code. That code use 0xf0 and 0xff both at cfi_reset_default method. Do you think this way?

• modify conf

• modify dts

This is dmesg.

• add mdio dependeny

• fixed igor error

• change spibus and add vertion infomation

• add mutex lock at smi access

I use igor tools and fixed all error. Thnaks.

• review refict

JEDEC CFI document written "Read Array data is FFh/F0h". I refer flashrom open source code. In this code probe_82802ab89 method is use 0xff and probe_jedec method is use 0xf0 by reset. probe_82802ab89 is 26 chips and probe_jedec is 128 chips in source code table. I think complete table is two big resource like as flashrom. I think option is good now.

This is boot log.

I have build error on sys/mips/mediatek today.

I seem irq is u_int from other code.

• review refict

v2 patch is good.

This is always false in patch.

if statement is same as current code. But POC2_UNTAG_VLAN don't have RT3050. I think check RT3050 first is good.

if delete to member in vlangroup the current code make error.

• delete temporaly line

• refict review and delete rtc code because of rt1310 don't have rtc

• add comment

Why delete my added gpio_delay() in gpiospi.c ? My KSZ8995MA code don't work no gpio_delay() on my target. I think current code clock is wrong.

• back to original code at GPIOBUS_PIN_SETFLAG. Because of gpiobus.c fixed

This is my setting hints.

I check this code on my develop SPI module code that is ksz8995ma ether switch chip and FON2100. This case delay is fixed problem and work. I check signal enclose picture. If no delay clock is not to zero.

If ignore GPIO_PIN_PULLUP/GPIO_PIN_PULLDOWN in low driver then GPIO_PIN_PULLUP/GPIO_PIN_PULLDOWN flag have no meaning in a system.

I seem GPIO_PIN_PULLUP/GPIO_PIN_PULLDOWN not set in any sys/mips/ gpio code. And gpioiic.c not use GPIO_PIN_PULLUP/GPIO_PIN_PULLDOWN that is same bitbang code . I think better not use in gpiospi.c rather than low driver ignore.

gpiobus_pin_setflags() in gpibus.c have check gpio_check_flags(). This code check pin capabirity. If low driver not support GPIO_PIN_PULLUP/GPIO_PIN_PULLDOWN return EINVAL.

• style and cleanup

@mizhka_gmail.com 88e6060 is not DOT1Q vlan support. It is Original Ingress and Egress Trailer. I think two way of support VLAN this chip. One is vlan(4) like support. Or other is interface driver code support. FON2201 original code use last one. But this is old chip I think leave alone is good. :)

1. add more macros.

2 This code is same as other ehterswitch code.

3. add space.
4. Other etherswitch code not check malloc also...
5. Check only Product Code.

• add empty line

• review refict

• more style(9)

• review refict

• review refict

• move cfi entory to board setting

• Merge branch 'master' into ar531x_support
• fixed build error

• fix gpioled support

• review refict

• delete not use line

back to base and make diff

• update diff

• modify by style(9) formant

• fixed non initialize soft use and softc initialze is first in function.

refict review