Page MenuHomeFreeBSD
Files F131637468

D4210.diff
No OneTemporary
Actions

D4210.diff
View Options

Index: head/sys/arm/conf/ARMADA38X
===================================================================
--- head/sys/arm/conf/ARMADA38X
+++ head/sys/arm/conf/ARMADA38X
@@ -0,0 +1,63 @@
+#
+# Kernel configuration for Marvell Armada38x
+#
+# $FreeBSD$
+#
+
+include "../mv/armada38x/std.armada38x"
+include "std.armv6"
+
+ident ARMADA38X
+
+options SOC_MV_ARMADA38X
+
+makeoptions DEBUG=-g # Build kernel with gdb(1) debug symbols
+makeoptions WERROR="-Werror"
+
+options MD_ROOT
+#makeoptions MFS_IMAGE=/path/to/miniroot
+options ROOTDEVNAME=\"ufs:md0\"
+
+options SCHED_ULE # ULE scheduler
+#options SCHED_4BSD # 4BSD scheduler
+
+# Debugging
+#options DEBUG
+#options VERBOSE_SYSINIT
+options ALT_BREAK_TO_DEBUGGER
+options DDB
+#options GDB
+#options DIAGNOSTIC
+options INVARIANTS # Enable calls of extra sanity checking
+options INVARIANT_SUPPORT # Extra sanity checks of internal structures, required by INVARIANTS
+options KDB
+options KDB_TRACE
+#options WITNESS # Enable checks to detect deadlocks and cycles
+#options WITNESS_SKIPSPIN # Don't run witness on spinlocks for speed
+#options WITNESS_KDB
+#options BOOTVERBOSE
+
+# Pseudo devices
+device random
+device pty
+device loop
+device md
+
+# Serial ports
+device uart
+device uart_ns8250
+
+# Network
+device ether
+device vlan
+
+# Interrupt controllers
+device gic
+
+# Timers
+device mpcore_timer
+
+#FDT
+options FDT
+options FDT_DTB_STATIC
+makeoptions FDT_DTS_FILE=armada-388-gp.dts
Index: head/sys/arm/mv/armada38x/armada38x.c
===================================================================
--- head/sys/arm/mv/armada38x/armada38x.c
+++ head/sys/arm/mv/armada38x/armada38x.c
@@ -0,0 +1,54 @@
+/*-
+ * Copyright (c) 2015 Semihalf.
+ * Copyright (c) 2015 Stormshield.
+ * All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ * 1. Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND
+ * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
+ * ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE
+ * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
+ * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
+ * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
+ * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
+ * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
+ * SUCH DAMAGE.
+ */
+
+#include <sys/cdefs.h>
+__FBSDID("$FreeBSD$");
+
+#include <sys/param.h>
+#include <sys/systm.h>
+#include <sys/bus.h>
+
+#include <arm/mv/mvwin.h>
+#include <arm/mv/mvreg.h>
+#include <arm/mv/mvvar.h>
+
+uint32_t
+get_tclk(void)
+{
+ uint32_t sar;
+
+ /*
+ * On Armada38x TCLK can be configured to 250 MHz or 200 MHz.
+ * Current setting is read from Sample At Reset register.
+ */
+ sar = (uint32_t)get_sar_value();
+ sar = (sar & TCLK_MASK) >> TCLK_SHIFT;
+ if (sar == 0)
+ return (TCLK_250MHZ);
+ else
+ return (TCLK_200MHZ);
+}
Index: head/sys/arm/mv/armada38x/files.armada38x
===================================================================
--- head/sys/arm/mv/armada38x/files.armada38x
+++ head/sys/arm/mv/armada38x/files.armada38x
@@ -0,0 +1,4 @@
+# $FreeBSD$
+
+arm/mv/armada38x/armada38x.c standard
+arm/mv/rtc.c standard
Index: head/sys/arm/mv/armada38x/std.armada38x
===================================================================
--- head/sys/arm/mv/armada38x/std.armada38x
+++ head/sys/arm/mv/armada38x/std.armada38x
@@ -0,0 +1,10 @@
+# $FreeBSD$
+files "../mv/armada38x/files.armada38x"
+files "../mv/files.mv"
+cpu CPU_CORTEXA
+machine arm armv6
+
+makeoptions CONF_CFLAGS="-march=armv7a"
+makeoptions KERNVIRTADDR=0xc0000000
+
+options KERNVIRTADDR=0xc0000000
Index: head/sys/arm/mv/mv_common.c
===================================================================
--- head/sys/arm/mv/mv_common.c
+++ head/sys/arm/mv/mv_common.c
@@ -260,7 +260,7 @@
bus_space_write_4(fdtbus_bs_tag, MV_CPU_CONTROL_BASE, reg, val);
}
-#if defined(SOC_MV_ARMADAXP)
+#if defined(SOC_MV_ARMADAXP) || defined(SOC_MV_ARMADA38X)
uint32_t
read_cpu_mp_clocks(uint32_t reg)
{
@@ -294,7 +294,7 @@
cpu_reset(void)
{
-#if defined(SOC_MV_ARMADAXP)
+#if defined(SOC_MV_ARMADAXP) || defined (SOC_MV_ARMADA38X)
write_cpu_misc(RSTOUTn_MASK, SOFT_RST_OUT_EN);
write_cpu_misc(SYSTEM_SOFT_RESET, SYS_SOFT_RST);
#else
@@ -442,6 +442,15 @@
else if (r == 1)
rev = "A1";
break;
+ case MV_DEV_88F6828:
+ dev = "Marvell 88F6828";
+ break;
+ case MV_DEV_88F6820:
+ dev = "Marvell 88F6820";
+ break;
+ case MV_DEV_88F6810:
+ dev = "Marvell 88F6810";
+ break;
case MV_DEV_MV78100_Z0:
dev = "Marvell MV78100 Z0";
break;
@@ -2195,6 +2204,10 @@
SAMPLE_AT_RESET_HI);
sar_low = bus_space_read_4(fdtbus_bs_tag, MV_MISC_BASE,
SAMPLE_AT_RESET_LO);
+#elif defined(SOC_MV_ARMADA38X)
+ sar_high = 0;
+ sar_low = bus_space_read_4(fdtbus_bs_tag, MV_MISC_BASE,
+ SAMPLE_AT_RESET);
#else
/*
* TODO: Add getting proper values for other SoC configurations
Index: head/sys/arm/mv/mvreg.h
===================================================================
--- head/sys/arm/mv/mvreg.h
+++ head/sys/arm/mv/mvreg.h
@@ -123,7 +123,7 @@
/*
* System reset
*/
-#if defined(SOC_MV_ARMADAXP)
+#if defined(SOC_MV_ARMADAXP) || defined(SOC_MV_ARMADA38X)
#define RSTOUTn_MASK 0x60
#define SYSTEM_SOFT_RESET 0x64
#define WD_RSTOUTn_MASK 0x4
@@ -346,6 +346,8 @@
#define SAMPLE_AT_RESET 0x30
#elif defined(SOC_MV_FREY)
#define SAMPLE_AT_RESET 0x100
+#elif defined(SOC_MV_ARMADA38X)
+#define SAMPLE_AT_RESET 0x400
#endif
#if defined(SOC_MV_DISCOVERY)
#define SAMPLE_AT_RESET_LO 0x30
@@ -370,6 +372,9 @@
#elif defined(SOC_MV_LOKIPLUS)
#define TCLK_MASK 0x0000F000
#define TCLK_SHIFT 0x0C
+#elif defined(SOC_MV_ARMADA38X)
+#define TCLK_MASK 0x00008000
+#define TCLK_SHIFT 15
#endif
#define TCLK_100MHZ 100000000
@@ -415,6 +420,9 @@
#define MV_DEV_88F6281 0x6281
#define MV_DEV_88F6282 0x6282
#define MV_DEV_88F6781 0x6781
+#define MV_DEV_88F6828 0x6828
+#define MV_DEV_88F6820 0x6820
+#define MV_DEV_88F6810 0x6810
#define MV_DEV_MV78100_Z0 0x6381
#define MV_DEV_MV78100 0x7810
#define MV_DEV_MV78130 0x7813
Index: head/sys/arm/mv/mvvar.h
===================================================================
--- head/sys/arm/mv/mvvar.h
+++ head/sys/arm/mv/mvvar.h
@@ -109,7 +109,7 @@
uint32_t read_cpu_ctrl(uint32_t);
void write_cpu_ctrl(uint32_t, uint32_t);
-#if defined(SOC_MV_ARMADAXP)
+#if defined(SOC_MV_ARMADAXP) || defined(SOC_MV_ARMADA38X)
uint32_t read_cpu_mp_clocks(uint32_t reg);
void write_cpu_mp_clocks(uint32_t reg, uint32_t val);
uint32_t read_cpu_misc(uint32_t reg);
Index: head/sys/arm/mv/mvwin.h
===================================================================
--- head/sys/arm/mv/mvwin.h
+++ head/sys/arm/mv/mvwin.h
@@ -73,6 +73,8 @@
#define MV_PCI_PORTS 2 /* 2x PCIE */
#elif defined(SOC_MV_ARMADAXP)
#define MV_PCI_PORTS 3 /* 3x PCIE */
+#elif defined(SOC_MV_ARMADA38X)
+#define MV_PCI_PORTS 4 /* 4x PCIE */
#else
#error "MV_PCI_PORTS not configured !"
#endif
@@ -129,7 +131,7 @@
#endif
#define MV_MPP_BASE (MV_BASE + 0x10000)
-#if defined(SOC_MV_ARMADAXP)
+#if defined(SOC_MV_ARMADAXP) || defined(SOC_MV_ARMADA38X)
#define MV_MISC_BASE (MV_BASE + 0x18200)
#define MV_MBUS_BRIDGE_BASE (MV_BASE + 0x20000)
#define MV_INTREGS_BASE (MV_MBUS_BRIDGE_BASE + 0x80)
Index: head/sys/arm/mv/timer.c
===================================================================
--- head/sys/arm/mv/timer.c
+++ head/sys/arm/mv/timer.c
@@ -54,7 +54,7 @@
#define INITIAL_TIMECOUNTER (0xffffffff)
#define MAX_WATCHDOG_TICKS (0xffffffff)
-#if defined(SOC_MV_ARMADAXP)
+#if defined(SOC_MV_ARMADAXP) || defined(SOC_MV_ARMADA38X)
#define MV_CLOCK_SRC 25000000 /* Timers' 25MHz mode */
#else
#define MV_CLOCK_SRC get_tclk()
@@ -124,7 +124,7 @@
int error;
void *ihl;
struct mv_timer_softc *sc;
-#if !defined(SOC_MV_ARMADAXP)
+#if !defined(SOC_MV_ARMADAXP) && !defined(SOC_MV_ARMADA38X)
uint32_t irq_cause, irq_mask;
#endif
@@ -155,7 +155,7 @@
}
mv_setup_timers();
-#if !defined(SOC_MV_ARMADAXP)
+#if !defined(SOC_MV_ARMADAXP) && !defined(SOC_MV_ARMADA38X)
irq_cause = read_cpu_ctrl(BRIDGE_IRQ_CAUSE);
irq_cause &= IRQ_TIMER0_CLR;
@@ -294,7 +294,7 @@
mv_watchdog_enable(void)
{
uint32_t val, irq_cause;
-#if !defined(SOC_MV_ARMADAXP)
+#if !defined(SOC_MV_ARMADAXP) && !defined(SOC_MV_ARMADA38X)
uint32_t irq_mask;
#endif
@@ -302,7 +302,7 @@
irq_cause &= IRQ_TIMER_WD_CLR;
write_cpu_ctrl(BRIDGE_IRQ_CAUSE, irq_cause);
-#if defined(SOC_MV_ARMADAXP)
+#if defined(SOC_MV_ARMADAXP) || defined(SOC_MV_ARMADA38X)
val = read_cpu_mp_clocks(WD_RSTOUTn_MASK);
val |= (WD_GLOBAL_MASK | WD_CPU0_MASK);
write_cpu_mp_clocks(WD_RSTOUTn_MASK, val);
@@ -318,7 +318,7 @@
val = mv_get_timer_control();
val |= CPU_TIMER_WD_EN | CPU_TIMER_WD_AUTO;
-#if defined(SOC_MV_ARMADAXP)
+#if defined(SOC_MV_ARMADAXP) || defined(SOC_MV_ARMADA38X)
val |= CPU_TIMER_WD_25MHZ_EN;
#endif
mv_set_timer_control(val);
@@ -328,7 +328,7 @@
mv_watchdog_disable(void)
{
uint32_t val, irq_cause;
-#if !defined(SOC_MV_ARMADAXP)
+#if !defined(SOC_MV_ARMADAXP) && !defined(SOC_MV_ARMADA38X)
uint32_t irq_mask;
#endif
@@ -336,7 +336,7 @@
val &= ~(CPU_TIMER_WD_EN | CPU_TIMER_WD_AUTO);
mv_set_timer_control(val);
-#if defined(SOC_MV_ARMADAXP)
+#if defined(SOC_MV_ARMADAXP) || defined(SOC_MV_ARMADA38X)
val = read_cpu_mp_clocks(WD_RSTOUTn_MASK);
val &= ~(WD_GLOBAL_MASK | WD_CPU0_MASK);
write_cpu_mp_clocks(WD_RSTOUTn_MASK, val);
@@ -438,7 +438,7 @@
val = mv_get_timer_control();
val &= ~(CPU_TIMER0_EN | CPU_TIMER0_AUTO);
val |= CPU_TIMER1_EN | CPU_TIMER1_AUTO;
-#if defined(SOC_MV_ARMADAXP)
+#if defined(SOC_MV_ARMADAXP) || defined(SOC_MV_ARMADA38X)
/* Enable 25MHz mode */
val |= CPU_TIMER0_25MHZ_EN | CPU_TIMER1_25MHZ_EN;
#endif
Index: head/sys/boot/fdt/dts/arm/armada-380.dtsi
===================================================================
--- head/sys/boot/fdt/dts/arm/armada-380.dtsi
+++ head/sys/boot/fdt/dts/arm/armada-380.dtsi
@@ -0,0 +1,154 @@
+/*
+ * Device Tree Include file for Marvell Armada 380 SoC.
+ *
+ * Copyright (C) 2014 Marvell
+ *
+ * Lior Amsalem <alior@marvell.com>
+ * Gregory CLEMENT <gregory.clement@free-electrons.com>
+ * Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ *
+ * $FreeBSD$
+ */
+
+#include "armada-38x.dtsi"
+
+/ {
+ model = "Marvell Armada 380 family SoC";
+ compatible = "marvell,armada380";
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ enable-method = "marvell,armada-380-smp";
+
+ cpu@0 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a9";
+ reg = <0>;
+ };
+ };
+
+ soc {
+ internal-regs {
+ pinctrl@18000 {
+ compatible = "marvell,mv88f6810-pinctrl";
+ };
+ };
+
+ pcie-controller {
+ compatible = "marvell,armada-370-pcie";
+ status = "disabled";
+ device_type = "pci";
+
+ #address-cells = <3>;
+ #size-cells = <2>;
+
+ msi-parent = <&mpic>;
+ bus-range = <0x00 0xff>;
+
+ ranges =
+ <0x82000000 0 0x80000 MBUS_ID(0xf0, 0x01) 0x80000 0 0x00002000
+ 0x82000000 0 0x40000 MBUS_ID(0xf0, 0x01) 0x40000 0 0x00002000
+ 0x82000000 0 0x44000 MBUS_ID(0xf0, 0x01) 0x44000 0 0x00002000
+ 0x82000000 0 0x48000 MBUS_ID(0xf0, 0x01) 0x48000 0 0x00002000
+ 0x82000000 0x1 0 MBUS_ID(0x08, 0xe8) 0 1 0 /* Port 0 MEM */
+ 0x81000000 0x1 0 MBUS_ID(0x08, 0xe0) 0 1 0 /* Port 0 IO */
+ 0x82000000 0x2 0 MBUS_ID(0x04, 0xe8) 0 1 0 /* Port 1 MEM */
+ 0x81000000 0x2 0 MBUS_ID(0x04, 0xe0) 0 1 0 /* Port 1 IO */
+ 0x82000000 0x3 0 MBUS_ID(0x04, 0xd8) 0 1 0 /* Port 2 MEM */
+ 0x81000000 0x3 0 MBUS_ID(0x04, 0xd0) 0 1 0 /* Port 2 IO */>;
+
+ /* x1 port */
+ pcie@1,0 {
+ device_type = "pci";
+ assigned-addresses = <0x82000800 0 0x80000 0 0x2000>;
+ reg = <0x0800 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0
+ 0x81000000 0 0 0x81000000 0x1 0 1 0>;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &gic GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
+ marvell,pcie-port = <0>;
+ marvell,pcie-lane = <0>;
+ clocks = <&gateclk 8>;
+ status = "disabled";
+ };
+
+ /* x1 port */
+ pcie@2,0 {
+ device_type = "pci";
+ assigned-addresses = <0x82000800 0 0x40000 0 0x2000>;
+ reg = <0x1000 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ ranges = <0x82000000 0 0 0x82000000 0x2 0 1 0
+ 0x81000000 0 0 0x81000000 0x2 0 1 0>;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &gic GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
+ marvell,pcie-port = <1>;
+ marvell,pcie-lane = <0>;
+ clocks = <&gateclk 5>;
+ status = "disabled";
+ };
+
+ /* x1 port */
+ pcie@3,0 {
+ device_type = "pci";
+ assigned-addresses = <0x82000800 0 0x44000 0 0x2000>;
+ reg = <0x1800 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ ranges = <0x82000000 0 0 0x82000000 0x3 0 1 0
+ 0x81000000 0 0 0x81000000 0x3 0 1 0>;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &gic GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>;
+ marvell,pcie-port = <2>;
+ marvell,pcie-lane = <0>;
+ clocks = <&gateclk 6>;
+ status = "disabled";
+ };
+ };
+ };
+};
Index: head/sys/boot/fdt/dts/arm/armada-385.dtsi
===================================================================
--- head/sys/boot/fdt/dts/arm/armada-385.dtsi
+++ head/sys/boot/fdt/dts/arm/armada-385.dtsi
@@ -0,0 +1,186 @@
+/*
+ * Device Tree Include file for Marvell Armada 385 SoC.
+ *
+ * Copyright (C) 2014 Marvell
+ *
+ * Lior Amsalem <alior@marvell.com>
+ * Gregory CLEMENT <gregory.clement@free-electrons.com>
+ * Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ *
+ * $FreeBSD$
+ */
+
+#include "armada-38x.dtsi"
+
+/ {
+ model = "Marvell Armada 385 family SoC";
+ compatible = "marvell,armada385", "marvell,armada380";
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ enable-method = "marvell,armada-380-smp";
+
+ cpu@0 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a9";
+ reg = <0>;
+ };
+ cpu@1 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a9";
+ reg = <1>;
+ };
+ };
+
+ soc {
+ internal-regs {
+ pinctrl@18000 {
+ compatible = "marvell,mv88f6820-pinctrl";
+ };
+ };
+
+ pcie-controller {
+ compatible = "marvell,armada-370-pcie";
+ status = "disabled";
+ device_type = "pci";
+
+ #address-cells = <3>;
+ #size-cells = <2>;
+
+ msi-parent = <&mpic>;
+ bus-range = <0x00 0xff>;
+
+ ranges =
+ <0x82000000 0 0x80000 MBUS_ID(0xf0, 0x01) 0x80000 0 0x00002000
+ 0x82000000 0 0x40000 MBUS_ID(0xf0, 0x01) 0x40000 0 0x00002000
+ 0x82000000 0 0x44000 MBUS_ID(0xf0, 0x01) 0x44000 0 0x00002000
+ 0x82000000 0 0x48000 MBUS_ID(0xf0, 0x01) 0x48000 0 0x00002000
+ 0x82000000 0x1 0 MBUS_ID(0x08, 0xe8) 0 1 0 /* Port 0 MEM */
+ 0x81000000 0x1 0 MBUS_ID(0x08, 0xe0) 0 1 0 /* Port 0 IO */
+ 0x82000000 0x2 0 MBUS_ID(0x04, 0xe8) 0 1 0 /* Port 1 MEM */
+ 0x81000000 0x2 0 MBUS_ID(0x04, 0xe0) 0 1 0 /* Port 1 IO */
+ 0x82000000 0x3 0 MBUS_ID(0x04, 0xd8) 0 1 0 /* Port 2 MEM */
+ 0x81000000 0x3 0 MBUS_ID(0x04, 0xd0) 0 1 0 /* Port 2 IO */
+ 0x82000000 0x4 0 MBUS_ID(0x04, 0xb8) 0 1 0 /* Port 3 MEM */
+ 0x81000000 0x4 0 MBUS_ID(0x04, 0xb0) 0 1 0 /* Port 3 IO */>;
+
+ /*
+ * This port can be either x4 or x1. When
+ * configured in x4 by the bootloader, then
+ * pcie@4,0 is not available.
+ */
+ pcie@1,0 {
+ device_type = "pci";
+ assigned-addresses = <0x82000800 0 0x80000 0 0x2000>;
+ reg = <0x0800 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0
+ 0x81000000 0 0 0x81000000 0x1 0 1 0>;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &gic GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
+ marvell,pcie-port = <0>;
+ marvell,pcie-lane = <0>;
+ clocks = <&gateclk 8>;
+ status = "disabled";
+ };
+
+ /* x1 port */
+ pcie@2,0 {
+ device_type = "pci";
+ assigned-addresses = <0x82000800 0 0x40000 0 0x2000>;
+ reg = <0x1000 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ ranges = <0x82000000 0 0 0x82000000 0x2 0 1 0
+ 0x81000000 0 0 0x81000000 0x2 0 1 0>;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &gic GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
+ marvell,pcie-port = <1>;
+ marvell,pcie-lane = <0>;
+ clocks = <&gateclk 5>;
+ status = "disabled";
+ };
+
+ /* x1 port */
+ pcie@3,0 {
+ device_type = "pci";
+ assigned-addresses = <0x82000800 0 0x44000 0 0x2000>;
+ reg = <0x1800 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ ranges = <0x82000000 0 0 0x82000000 0x3 0 1 0
+ 0x81000000 0 0 0x81000000 0x3 0 1 0>;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &gic GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>;
+ marvell,pcie-port = <2>;
+ marvell,pcie-lane = <0>;
+ clocks = <&gateclk 6>;
+ status = "disabled";
+ };
+
+ /*
+ * x1 port only available when pcie@1,0 is
+ * configured as a x1 port
+ */
+ pcie@4,0 {
+ device_type = "pci";
+ assigned-addresses = <0x82000800 0 0x48000 0 0x2000>;
+ reg = <0x2000 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ ranges = <0x82000000 0 0 0x82000000 0x4 0 1 0
+ 0x81000000 0 0 0x81000000 0x4 0 1 0>;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &gic GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
+ marvell,pcie-port = <3>;
+ marvell,pcie-lane = <0>;
+ clocks = <&gateclk 7>;
+ status = "disabled";
+ };
+ };
+ };
+};
Index: head/sys/boot/fdt/dts/arm/armada-388-gp.dts
===================================================================
--- head/sys/boot/fdt/dts/arm/armada-388-gp.dts
+++ head/sys/boot/fdt/dts/arm/armada-388-gp.dts
@@ -0,0 +1,415 @@
+/*
+ * Device Tree file for Marvell Armada 385 development board
+ * (RD-88F6820-GP)
+ *
+ * Copyright (C) 2014 Marvell
+ *
+ * Gregory CLEMENT <gregory.clement@free-electrons.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without
+ * any warranty of any kind, whether express or implied.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ *
+ * $FreeBSD$
+ */
+
+/dts-v1/;
+#include "armada-388.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ model = "Marvell Armada 385 GP";
+ compatible = "marvell,a385-gp", "marvell,armada388", "marvell,armada380";
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0x00000000 0x80000000>; /* 2 GB */
+ };
+
+ soc {
+ ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000
+ MBUS_ID(0x01, 0x1d) 0 0xfff00000 0x100000>;
+
+ internal-regs {
+ spi@10600 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi0_pins>;
+ status = "okay";
+
+ spi-flash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "st,m25p128", "jedec,spi-nor";
+ reg = <0>; /* Chip select 0 */
+ spi-max-frequency = <50000000>;
+ m25p,fast-read;
+ };
+ };
+
+ i2c@11000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins>;
+ status = "okay";
+ clock-frequency = <100000>;
+ /*
+ * The EEPROM located at adresse 54 is needed
+ * for the boot - DO NOT ERASE IT -
+ */
+
+ expander0: pca9555@20 {
+ compatible = "nxp,pca9555";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pca0_pins>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <18 IRQ_TYPE_EDGE_FALLING>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ reg = <0x20>;
+ };
+
+ expander1: pca9555@21 {
+ compatible = "nxp,pca9555";
+ pinctrl-names = "default";
+ interrupt-parent = <&gpio0>;
+ interrupts = <18 IRQ_TYPE_EDGE_FALLING>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ reg = <0x21>;
+ };
+
+ };
+
+ serial@12000 {
+ /*
+ * Exported on the micro USB connector CON16
+ * through an FTDI
+ */
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins>;
+ status = "okay";
+ };
+
+ /* GE1 CON15 */
+ ethernet@30000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&ge1_rgmii_pins>;
+ status = "okay";
+ phy = <&phy1>;
+ phy-mode = "rgmii-id";
+ };
+
+ /* CON4 */
+ usb@58000 {
+ vcc-supply = <&reg_usb2_0_vbus>;
+ status = "okay";
+ };
+
+ /* GE0 CON1 */
+ ethernet@70000 {
+ pinctrl-names = "default";
+ /*
+ * The Reference Clock 0 is used to provide a
+ * clock to the PHY
+ */
+ pinctrl-0 = <&ge0_rgmii_pins>, <&ref_clk0_pins>;
+ status = "okay";
+ phy = <&phy0>;
+ phy-mode = "rgmii-id";
+ };
+
+
+ mdio@72004 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mdio_pins>;
+
+ phy0: ethernet-phy@1 {
+ reg = <1>;
+ };
+
+ phy1: ethernet-phy@0 {
+ reg = <0>;
+ };
+ };
+
+ sata@a8000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&sata0_pins>, <&sata1_pins>;
+ status = "okay";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ sata0: sata-port@0 {
+ reg = <0>;
+ target-supply = <&reg_5v_sata0>;
+ };
+
+ sata1: sata-port@1 {
+ reg = <1>;
+ target-supply = <&reg_5v_sata1>;
+ };
+ };
+
+ sata@e0000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&sata2_pins>, <&sata3_pins>;
+ status = "okay";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ sata2: sata-port@0 {
+ reg = <0>;
+ target-supply = <&reg_5v_sata2>;
+ };
+
+ sata3: sata-port@1 {
+ reg = <1>;
+ target-supply = <&reg_5v_sata3>;
+ };
+ };
+
+ sdhci@d8000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdhci_pins>;
+ cd-gpios = <&expander0 5 GPIO_ACTIVE_LOW>;
+ no-1-8-v;
+ wp-inverted;
+ bus-width = <8>;
+ status = "okay";
+ };
+
+ /* CON5 */
+ usb3@f0000 {
+ vcc-supply = <&reg_usb2_1_vbus>;
+ status = "okay";
+ };
+
+ /* CON7 */
+ usb3@f8000 {
+ vcc-supply = <&reg_usb3_vbus>;
+ status = "okay";
+ };
+ };
+
+ pcie-controller {
+ status = "okay";
+ /*
+ * One PCIe units is accessible through
+ * standard PCIe slot on the board.
+ */
+ pcie@1,0 {
+ /* Port 0, Lane 0 */
+ status = "okay";
+ };
+
+ /*
+ * The two other PCIe units are accessible
+ * through mini PCIe slot on the board.
+ */
+ pcie@2,0 {
+ /* Port 1, Lane 0 */
+ status = "okay";
+ };
+ pcie@3,0 {
+ /* Port 2, Lane 0 */
+ status = "okay";
+ };
+ };
+
+ gpio-fan {
+ compatible = "gpio-fan";
+ gpios = <&expander1 3 GPIO_ACTIVE_HIGH>;
+ gpio-fan,speed-map = < 0 0
+ 3000 1>;
+ };
+ };
+
+ reg_usb3_vbus: usb3-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usb3-vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ regulator-always-on;
+ gpio = <&expander1 15 GPIO_ACTIVE_HIGH>;
+ };
+
+ reg_usb2_0_vbus: v5-vbus0 {
+ compatible = "regulator-fixed";
+ regulator-name = "v5.0-vbus0";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ regulator-always-on;
+ gpio = <&expander1 14 GPIO_ACTIVE_HIGH>;
+ };
+
+ reg_usb2_1_vbus: v5-vbus1 {
+ compatible = "regulator-fixed";
+ regulator-name = "v5.0-vbus1";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ regulator-always-on;
+ gpio = <&expander0 4 GPIO_ACTIVE_HIGH>;
+ };
+
+ reg_usb2_1_vbus: v5-vbus1 {
+ compatible = "regulator-fixed";
+ regulator-name = "v5.0-vbus1";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ regulator-always-on;
+ gpio = <&expander0 4 GPIO_ACTIVE_HIGH>;
+ };
+
+ reg_sata0: pwr-sata0 {
+ compatible = "regulator-fixed";
+ regulator-name = "pwr_en_sata0";
+ enable-active-high;
+ regulator-always-on;
+
+ };
+
+ reg_5v_sata0: v5-sata0 {
+ compatible = "regulator-fixed";
+ regulator-name = "v5.0-sata0";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ vin-supply = <&reg_sata0>;
+ };
+
+ reg_12v_sata0: v12-sata0 {
+ compatible = "regulator-fixed";
+ regulator-name = "v12.0-sata0";
+ regulator-min-microvolt = <12000000>;
+ regulator-max-microvolt = <12000000>;
+ regulator-always-on;
+ vin-supply = <&reg_sata0>;
+ };
+
+ reg_sata1: pwr-sata1 {
+ regulator-name = "pwr_en_sata1";
+ compatible = "regulator-fixed";
+ regulator-min-microvolt = <12000000>;
+ regulator-max-microvolt = <12000000>;
+ enable-active-high;
+ regulator-always-on;
+ gpio = <&expander0 3 GPIO_ACTIVE_HIGH>;
+ };
+
+ reg_5v_sata1: v5-sata1 {
+ compatible = "regulator-fixed";
+ regulator-name = "v5.0-sata1";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ vin-supply = <&reg_sata1>;
+ };
+
+ reg_12v_sata1: v12-sata1 {
+ compatible = "regulator-fixed";
+ regulator-name = "v12.0-sata1";
+ regulator-min-microvolt = <12000000>;
+ regulator-max-microvolt = <12000000>;
+ regulator-always-on;
+ vin-supply = <&reg_sata1>;
+ };
+
+ reg_sata2: pwr-sata2 {
+ compatible = "regulator-fixed";
+ regulator-name = "pwr_en_sata2";
+ enable-active-high;
+ regulator-always-on;
+ gpio = <&expander0 11 GPIO_ACTIVE_HIGH>;
+ };
+
+ reg_5v_sata2: v5-sata2 {
+ compatible = "regulator-fixed";
+ regulator-name = "v5.0-sata2";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ vin-supply = <&reg_sata2>;
+ };
+
+ reg_12v_sata2: v12-sata2 {
+ compatible = "regulator-fixed";
+ regulator-name = "v12.0-sata2";
+ regulator-min-microvolt = <12000000>;
+ regulator-max-microvolt = <12000000>;
+ regulator-always-on;
+ vin-supply = <&reg_sata2>;
+ };
+
+ reg_sata3: pwr-sata3 {
+ compatible = "regulator-fixed";
+ regulator-name = "pwr_en_sata3";
+ enable-active-high;
+ regulator-always-on;
+ gpio = <&expander0 12 GPIO_ACTIVE_HIGH>;
+ };
+
+ reg_5v_sata3: v5-sata3 {
+ compatible = "regulator-fixed";
+ regulator-name = "v5.0-sata3";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ vin-supply = <&reg_sata3>;
+ };
+
+ reg_12v_sata3: v12-sata3 {
+ compatible = "regulator-fixed";
+ regulator-name = "v12.0-sata3";
+ regulator-min-microvolt = <12000000>;
+ regulator-max-microvolt = <12000000>;
+ regulator-always-on;
+ vin-supply = <&reg_sata3>;
+ };
+};
+
+&pinctrl {
+ pca0_pins: pca0_pins {
+ marvell,pins = "mpp18";
+ marvell,function = "gpio";
+ };
+};
Index: head/sys/boot/fdt/dts/arm/armada-388.dtsi
===================================================================
--- head/sys/boot/fdt/dts/arm/armada-388.dtsi
+++ head/sys/boot/fdt/dts/arm/armada-388.dtsi
@@ -0,0 +1,72 @@
+/*
+ * Device Tree Include file for Marvell Armada 388 SoC.
+ *
+ * Copyright (C) 2015 Marvell
+ *
+ * Gregory CLEMENT <gregory.clement@free-electrons.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without
+ * any warranty of any kind, whether express or implied.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ *
+ *
+ * The main difference with the Armada 385 is that the 388 can handle two more
+ * SATA ports. So we can reuse the dtsi of the Armada 385, override the pinctrl
+ * property and the name of the SoC, and add the second SATA host which control
+ * the 2 other ports.
+ *
+ * $FreeBSD$
+ */
+
+#include "armada-385.dtsi"
+
+/ {
+ model = "Marvell Armada 388 family SoC";
+ compatible = "marvell,armada388", "marvell,armada385",
+ "marvell,armada380";
+
+ soc {
+ internal-regs {
+ pinctrl@18000 {
+ compatible = "marvell,mv88f6828-pinctrl";
+ };
+
+ sata@e0000 {
+ compatible = "marvell,armada-380-ahci";
+ reg = <0xe0000 0x2000>;
+ interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gateclk 30>;
+ status = "disabled";
+ };
+
+ };
+ };
+};
Index: head/sys/boot/fdt/dts/arm/armada-38x.dtsi
===================================================================
--- head/sys/boot/fdt/dts/arm/armada-38x.dtsi
+++ head/sys/boot/fdt/dts/arm/armada-38x.dtsi
@@ -0,0 +1,602 @@
+/*
+ * Device Tree Include file for Marvell Armada 38x family of SoCs.
+ *
+ * Copyright (C) 2014 Marvell
+ *
+ * Lior Amsalem <alior@marvell.com>
+ * Gregory CLEMENT <gregory.clement@free-electrons.com>
+ * Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ *
+ * $FreeBSD$
+ */
+
+#include "skeleton.dtsi"
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+#define MBUS_ID(target,attributes) (((target) << 24) | ((attributes) << 16))
+
+/ {
+ model = "Marvell Armada 38x family SoC";
+ compatible = "marvell,armada380";
+
+ aliases {
+ gpio0 = &gpio0;
+ gpio1 = &gpio1;
+ serial0 = &uart0;
+ serial1 = &uart1;
+ };
+
+ pmu {
+ compatible = "arm,cortex-a9-pmu";
+ interrupts-extended = <&mpic 3>;
+ };
+
+ soc {
+ compatible = "marvell,armada380-mbus", "simple-bus";
+ #address-cells = <2>;
+ #size-cells = <1>;
+ controller = <&mbusc>;
+ interrupt-parent = <&gic>;
+ pcie-mem-aperture = <0xe0000000 0x8000000>;
+ pcie-io-aperture = <0xe8000000 0x100000>;
+
+ bootrom {
+ compatible = "marvell,bootrom";
+ reg = <MBUS_ID(0x01, 0x1d) 0 0x200000>;
+ };
+
+ devbus-bootcs {
+ compatible = "marvell,mvebu-devbus";
+ reg = <MBUS_ID(0xf0, 0x01) 0x10400 0x8>;
+ ranges = <0 MBUS_ID(0x01, 0x2f) 0 0xffffffff>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ clocks = <&coreclk 0>;
+ status = "disabled";
+ };
+
+ devbus-cs0 {
+ compatible = "marvell,mvebu-devbus";
+ reg = <MBUS_ID(0xf0, 0x01) 0x10408 0x8>;
+ ranges = <0 MBUS_ID(0x01, 0x3e) 0 0xffffffff>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ clocks = <&coreclk 0>;
+ status = "disabled";
+ };
+
+ devbus-cs1 {
+ compatible = "marvell,mvebu-devbus";
+ reg = <MBUS_ID(0xf0, 0x01) 0x10410 0x8>;
+ ranges = <0 MBUS_ID(0x01, 0x3d) 0 0xffffffff>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ clocks = <&coreclk 0>;
+ status = "disabled";
+ };
+
+ devbus-cs2 {
+ compatible = "marvell,mvebu-devbus";
+ reg = <MBUS_ID(0xf0, 0x01) 0x10418 0x8>;
+ ranges = <0 MBUS_ID(0x01, 0x3b) 0 0xffffffff>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ clocks = <&coreclk 0>;
+ status = "disabled";
+ };
+
+ devbus-cs3 {
+ compatible = "marvell,mvebu-devbus";
+ reg = <MBUS_ID(0xf0, 0x01) 0x10420 0x8>;
+ ranges = <0 MBUS_ID(0x01, 0x37) 0 0xffffffff>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ clocks = <&coreclk 0>;
+ status = "disabled";
+ };
+
+ internal-regs {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 MBUS_ID(0xf0, 0x01) 0 0x100000>;
+
+ L2: cache-controller@8000 {
+ compatible = "arm,pl310-cache";
+ reg = <0x8000 0x1000>;
+ cache-unified;
+ cache-level = <2>;
+ };
+
+ scu@c000 {
+ compatible = "arm,cortex-a9-scu";
+ reg = <0xc000 0x58>;
+ };
+
+ timer@c600 {
+ compatible = "arm,cortex-a9-twd-timer";
+ reg = <0xc600 0x20>;
+ interrupts = <GIC_PPI 13 (IRQ_TYPE_EDGE_RISING | GIC_CPU_MASK_SIMPLE(2))>;
+ clocks = <&coreclk 2>;
+ };
+
+ gic: interrupt-controller@d000 {
+ compatible = "arm,cortex-a9-gic";
+ #interrupt-cells = <3>;
+ #size-cells = <0>;
+ interrupt-controller;
+ reg = <0xd000 0x1000>,
+ <0xc100 0x100>;
+ };
+
+ spi0: spi@10600 {
+ compatible = "marvell,armada-380-spi",
+ "marvell,orion-spi";
+ reg = <0x10600 0x50>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ cell-index = <0>;
+ interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&coreclk 0>;
+ status = "disabled";
+ };
+
+ spi1: spi@10680 {
+ compatible = "marvell,armada-380-spi",
+ "marvell,orion-spi";
+ reg = <0x10680 0x50>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ cell-index = <1>;
+ interrupts = <GIC_SPI 63 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&coreclk 0>;
+ status = "disabled";
+ };
+
+ i2c0: i2c@11000 {
+ compatible = "marvell,mv64xxx-i2c";
+ reg = <0x11000 0x20>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
+ timeout-ms = <1000>;
+ clocks = <&coreclk 0>;
+ status = "disabled";
+ };
+
+ i2c1: i2c@11100 {
+ compatible = "marvell,mv64xxx-i2c";
+ reg = <0x11100 0x20>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
+ timeout-ms = <1000>;
+ clocks = <&coreclk 0>;
+ status = "disabled";
+ };
+
+ uart0: serial@12000 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x12000 0x100>;
+ reg-shift = <2>;
+ interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
+ reg-io-width = <1>;
+ clocks = <&coreclk 0>;
+ status = "disabled";
+ };
+
+ uart1: serial@12100 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x12100 0x100>;
+ reg-shift = <2>;
+ interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
+ reg-io-width = <1>;
+ clocks = <&coreclk 0>;
+ status = "disabled";
+ };
+
+ pinctrl: pinctrl@18000 {
+ reg = <0x18000 0x20>;
+
+ ge0_rgmii_pins: ge-rgmii-pins-0 {
+ marvell,pins = "mpp6", "mpp7", "mpp8",
+ "mpp9", "mpp10", "mpp11",
+ "mpp12", "mpp13", "mpp14",
+ "mpp15", "mpp16", "mpp17";
+ marvell,function = "ge0";
+ };
+
+ ge1_rgmii_pins: ge-rgmii-pins-1 {
+ marvell,pins = "mpp21", "mpp27", "mpp28",
+ "mpp29", "mpp30", "mpp31",
+ "mpp32", "mpp37", "mpp38",
+ "mpp39", "mpp40", "mpp41";
+ marvell,function = "ge1";
+ };
+
+ i2c0_pins: i2c-pins-0 {
+ marvell,pins = "mpp2", "mpp3";
+ marvell,function = "i2c0";
+ };
+
+ mdio_pins: mdio-pins {
+ marvell,pins = "mpp4", "mpp5";
+ marvell,function = "ge";
+ };
+
+ ref_clk0_pins: ref-clk-pins-0 {
+ marvell,pins = "mpp45";
+ marvell,function = "ref";
+ };
+
+ ref_clk1_pins: ref-clk-pins-1 {
+ marvell,pins = "mpp46";
+ marvell,function = "ref";
+ };
+
+ spi0_pins: spi-pins-0 {
+ marvell,pins = "mpp22", "mpp23", "mpp24",
+ "mpp25";
+ marvell,function = "spi0";
+ };
+
+ spi1_pins: spi-pins-1 {
+ marvell,pins = "mpp56", "mpp57", "mpp58",
+ "mpp59";
+ marvell,function = "spi1";
+ };
+
+ uart0_pins: uart-pins-0 {
+ marvell,pins = "mpp0", "mpp1";
+ marvell,function = "ua0";
+ };
+
+ uart1_pins: uart-pins-1 {
+ marvell,pins = "mpp19", "mpp20";
+ marvell,function = "ua1";
+ };
+
+ sdhci_pins: sdhci-pins {
+ marvell,pins = "mpp48", "mpp49", "mpp50",
+ "mpp52", "mpp53", "mpp54",
+ "mpp55", "mpp57", "mpp58",
+ "mpp59";
+ marvell,function = "sd0";
+ };
+
+ sata0_pins: sata-pins-0 {
+ marvell,pins = "mpp20";
+ marvell,function = "sata0";
+ };
+
+ sata1_pins: sata-pins-1 {
+ marvell,pins = "mpp19";
+ marvell,function = "sata1";
+ };
+
+ sata2_pins: sata-pins-2 {
+ marvell,pins = "mpp47";
+ marvell,function = "sata2";
+ };
+
+ sata3_pins: sata-pins-3 {
+ marvell,pins = "mpp44";
+ marvell,function = "sata3";
+ };
+ };
+
+ gpio0: gpio@18100 {
+ compatible = "marvell,orion-gpio";
+ reg = <0x18100 0x40>;
+ ngpios = <32>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ gpio1: gpio@18140 {
+ compatible = "marvell,orion-gpio";
+ reg = <0x18140 0x40>;
+ ngpios = <28>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ interrupts = <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ system-controller@18200 {
+ compatible = "marvell,armada-380-system-controller",
+ "marvell,armada-370-xp-system-controller";
+ reg = <0x18200 0x100>;
+ };
+
+ gateclk: clock-gating-control@18220 {
+ compatible = "marvell,armada-380-gating-clock";
+ reg = <0x18220 0x4>;
+ clocks = <&coreclk 0>;
+ #clock-cells = <1>;
+ };
+
+ coreclk: mvebu-sar@18600 {
+ compatible = "marvell,armada-380-core-clock";
+ reg = <0x18600 0x04>;
+ #clock-cells = <1>;
+ };
+
+ mbusc: mbus-controller@20000 {
+ compatible = "marvell,mbus-controller";
+ reg = <0x20000 0x100>, <0x20180 0x20>;
+ };
+
+ mpic: interrupt-controller@20a00 {
+ compatible = "marvell,mpic";
+ reg = <0x20a00 0x2d0>, <0x21070 0x58>;
+ #interrupt-cells = <1>;
+ #size-cells = <1>;
+ interrupt-controller;
+ msi-controller;
+ interrupts = <GIC_PPI 15 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ timer@20300 {
+ compatible = "marvell,armada-380-timer",
+ "marvell,armada-xp-timer";
+ reg = <0x20300 0x30>, <0x21040 0x30>;
+ interrupts-extended = <&gic GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+ <&gic GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
+ <&gic GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>,
+ <&gic GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
+ <&mpic 5>,
+ <&mpic 6>;
+ clocks = <&coreclk 2>, <&refclk>;
+ clock-names = "nbclk", "fixed";
+ };
+
+ watchdog@20300 {
+ compatible = "marvell,armada-380-wdt";
+ reg = <0x20300 0x34>, <0x20704 0x4>, <0x18260 0x4>;
+ clocks = <&coreclk 2>, <&refclk>;
+ clock-names = "nbclk", "fixed";
+ };
+
+ cpurst@20800 {
+ compatible = "marvell,armada-370-cpu-reset";
+ reg = <0x20800 0x10>;
+ };
+
+ mpcore-soc-ctrl@20d20 {
+ compatible = "marvell,armada-380-mpcore-soc-ctrl";
+ reg = <0x20d20 0x6c>;
+ };
+
+ coherency-fabric@21010 {
+ compatible = "marvell,armada-380-coherency-fabric";
+ reg = <0x21010 0x1c>;
+ };
+
+ pmsu@22000 {
+ compatible = "marvell,armada-380-pmsu";
+ reg = <0x22000 0x1000>;
+ };
+
+ eth1: ethernet@30000 {
+ compatible = "marvell,armada-370-neta";
+ reg = <0x30000 0x4000>;
+ interrupts-extended = <&mpic 10>;
+ clocks = <&gateclk 3>;
+ status = "disabled";
+ };
+
+ eth2: ethernet@34000 {
+ compatible = "marvell,armada-370-neta";
+ reg = <0x34000 0x4000>;
+ interrupts-extended = <&mpic 12>;
+ clocks = <&gateclk 2>;
+ status = "disabled";
+ };
+
+ usb@58000 {
+ compatible = "marvell,orion-ehci";
+ reg = <0x58000 0x500>;
+ interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gateclk 18>;
+ status = "disabled";
+ };
+
+ xor@60800 {
+ compatible = "marvell,orion-xor";
+ reg = <0x60800 0x100
+ 0x60a00 0x100>;
+ clocks = <&gateclk 22>;
+ status = "okay";
+
+ xor00 {
+ interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
+ dmacap,memcpy;
+ dmacap,xor;
+ };
+ xor01 {
+ interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
+ dmacap,memcpy;
+ dmacap,xor;
+ dmacap,memset;
+ };
+ };
+
+ xor@60900 {
+ compatible = "marvell,orion-xor";
+ reg = <0x60900 0x100
+ 0x60b00 0x100>;
+ clocks = <&gateclk 28>;
+ status = "okay";
+
+ xor10 {
+ interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>;
+ dmacap,memcpy;
+ dmacap,xor;
+ };
+ xor11 {
+ interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>;
+ dmacap,memcpy;
+ dmacap,xor;
+ dmacap,memset;
+ };
+ };
+
+ eth0: ethernet@70000 {
+ compatible = "marvell,armada-370-neta";
+ reg = <0x70000 0x4000>;
+ interrupts-extended = <&mpic 8>;
+ clocks = <&gateclk 4>;
+ status = "disabled";
+ };
+
+ mdio: mdio@72004 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "marvell,orion-mdio";
+ reg = <0x72004 0x4>;
+ clocks = <&gateclk 4>;
+ };
+
+ rtc@a3800 {
+ compatible = "marvell,armada-380-rtc";
+ reg = <0xa3800 0x20>, <0x184a0 0x0c>;
+ reg-names = "rtc", "rtc-soc";
+ interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ sata@a8000 {
+ compatible = "marvell,armada-380-ahci";
+ reg = <0xa8000 0x2000>;
+ interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gateclk 15>;
+ status = "disabled";
+ };
+
+ sata@e0000 {
+ compatible = "marvell,armada-380-ahci";
+ reg = <0xe0000 0x2000>;
+ interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gateclk 30>;
+ status = "disabled";
+ };
+
+ coredivclk: clock@e4250 {
+ compatible = "marvell,armada-380-corediv-clock";
+ reg = <0xe4250 0xc>;
+ #clock-cells = <1>;
+ clocks = <&mainpll>;
+ clock-output-names = "nand";
+ };
+
+ thermal@e8078 {
+ compatible = "marvell,armada380-thermal";
+ reg = <0xe4078 0x4>, <0xe4074 0x4>;
+ status = "okay";
+ };
+
+ flash@d0000 {
+ compatible = "marvell,armada370-nand";
+ reg = <0xd0000 0x54>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&coredivclk 0>;
+ status = "disabled";
+ };
+
+ sdhci@d8000 {
+ compatible = "marvell,armada-380-sdhci";
+ reg-names = "sdhci", "mbus", "conf-sdio3";
+ reg = <0xd8000 0x1000>,
+ <0xdc000 0x100>,
+ <0x18454 0x4>;
+ interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gateclk 17>;
+ mrvl,clk-delay-cycles = <0x1F>;
+ status = "disabled";
+ };
+
+ usb3@f0000 {
+ compatible = "marvell,armada-380-xhci";
+ reg = <0xf0000 0x4000>,<0xf4000 0x4000>;
+ interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gateclk 9>;
+ status = "disabled";
+ };
+
+ usb3@f8000 {
+ compatible = "marvell,armada-380-xhci";
+ reg = <0xf8000 0x4000>,<0xfc000 0x4000>;
+ interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gateclk 10>;
+ status = "disabled";
+ };
+ };
+ };
+
+ clocks {
+ /* 2 GHz fixed main PLL */
+ mainpll: mainpll {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <1000000000>;
+ };
+
+ /* 25 MHz reference crystal */
+ refclk: oscillator {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <25000000>;
+ };
+ };
+};
Index: head/sys/conf/options.arm
===================================================================
--- head/sys/conf/options.arm
+++ head/sys/conf/options.arm
@@ -47,6 +47,7 @@
SOC_IMX53 opt_global.h
SOC_IMX6 opt_global.h
SOC_MV_ARMADAXP opt_global.h
+SOC_MV_ARMADA38X opt_global.h
SOC_MV_DISCOVERY opt_global.h
SOC_MV_DOVE opt_global.h
SOC_MV_FREY opt_global.h

File Metadata

Mime Type
text/plain
Expires
Fri, Oct 10, 10:55 PM (11 h, 10 m)
Storage Engine
blob
Storage Format
Raw Data
Storage Handle
23524829
Default Alt Text
D4210.diff (51 KB)

Event Timeline