Index: stable/12/sys/dev/ow/owc_gpiobus.c =================================================================== --- stable/12/sys/dev/ow/owc_gpiobus.c (revision 354530) +++ stable/12/sys/dev/ow/owc_gpiobus.c (revision 354531) @@ -1,422 +1,422 @@ /*- * Copyright (c) 2015 M. Warner Losh * All rights reserved. * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * 1. Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in the * documentation and/or other materials provided with the distribution. * * THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE * ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF * SUCH DAMAGE. */ #include __FBSDID("$FreeBSD$"); #include "opt_platform.h" #include #include #include #include #include #include #include #include #include #ifdef FDT #include #include #include #endif #include #include "gpiobus_if.h" #include #define OW_PIN 0 #define OWC_GPIOBUS_LOCK(_sc) mtx_lock(&(_sc)->sc_mtx) #define OWC_GPIOBUS_UNLOCK(_sc) mtx_unlock(&(_sc)->sc_mtx) #define OWC_GPIOBUS_LOCK_INIT(_sc) \ mtx_init(&_sc->sc_mtx, device_get_nameunit(_sc->sc_dev), \ "owc_gpiobus", MTX_DEF) #define OWC_GPIOBUS_LOCK_DESTROY(_sc) mtx_destroy(&_sc->sc_mtx); struct owc_gpiobus_softc { device_t sc_dev; device_t sc_busdev; struct mtx sc_mtx; }; static int owc_gpiobus_probe(device_t); static int owc_gpiobus_attach(device_t); static int owc_gpiobus_detach(device_t); #ifdef FDT static void owc_gpiobus_identify(driver_t *driver, device_t bus) { phandle_t w1, root; /* * Find all the 1-wire bus pseudo-nodes that are * at the top level of the FDT. Would be nice to * somehow preserve the node name of these busses, * but there's no good place to put it. The driver's * name is used for the device name, and the 1-wire * bus overwrites the description. */ root = OF_finddevice("/"); if (root == -1) return; for (w1 = OF_child(root); w1 != 0; w1 = OF_peer(w1)) { if (!fdt_is_compatible_strict(w1, "w1-gpio")) continue; if (!OF_hasprop(w1, "gpios")) continue; ofw_gpiobus_add_fdt_child(bus, driver->name, w1); } } #endif static int owc_gpiobus_probe(device_t dev) { #ifdef FDT if (!ofw_bus_status_okay(dev)) return (ENXIO); if (ofw_bus_is_compatible(dev, "w1-gpio")) { device_set_desc(dev, "FDT GPIO attached one-wire bus"); return (BUS_PROBE_DEFAULT); } return (ENXIO); #else device_set_desc(dev, "GPIO attached one-wire bus"); return 0; #endif } static int owc_gpiobus_attach(device_t dev) { struct owc_gpiobus_softc *sc; device_t *kids; int nkid; sc = device_get_softc(dev); sc->sc_dev = dev; sc->sc_busdev = device_get_parent(dev); OWC_GPIOBUS_LOCK_INIT(sc); nkid = 0; if (device_get_children(dev, &kids, &nkid) == 0) free(kids, M_TEMP); if (nkid == 0) device_add_child(dev, "ow", -1); bus_generic_attach(dev); return (0); } static int owc_gpiobus_detach(device_t dev) { struct owc_gpiobus_softc *sc; sc = device_get_softc(dev); OWC_GPIOBUS_LOCK_DESTROY(sc); bus_generic_detach(dev); return (0); } /* * In the diagrams below, R is driven by the resistor pullup, M is driven by the * master, and S is driven by the slave / target. */ /* * These macros let what why we're doing stuff shine in the code * below, and let the how be confined to here. */ #define GETBUS(sc) GPIOBUS_ACQUIRE_BUS((sc)->sc_busdev, \ (sc)->sc_dev, GPIOBUS_WAIT) #define RELBUS(sc) GPIOBUS_RELEASE_BUS((sc)->sc_busdev, \ (sc)->sc_dev) #define OUTPIN(sc) GPIOBUS_PIN_SETFLAGS((sc)->sc_busdev, \ (sc)->sc_dev, OW_PIN, GPIO_PIN_OUTPUT) #define INPIN(sc) GPIOBUS_PIN_SETFLAGS((sc)->sc_busdev, \ (sc)->sc_dev, OW_PIN, GPIO_PIN_INPUT) #define GETPIN(sc, bit) GPIOBUS_PIN_GET((sc)->sc_busdev, \ (sc)->sc_dev, OW_PIN, bit) #define LOW(sc) GPIOBUS_PIN_SET((sc)->sc_busdev, \ (sc)->sc_dev, OW_PIN, GPIO_PIN_LOW) /* * WRITE-ONE (see owll_if.m for timings) From Figure 4-1 AN-937 * * |<---------tSLOT---->|<-tREC->| * High RRRRM | RRRRRRRRRRRR|RRRRRRRRM * M | R | | | M * M| R | | | M * Low MMMMMMM | | | MMMMMM... * |<-tLOW1->| | | * |<------15us--->| | * |<--------60us---->| */ static int owc_gpiobus_write_one(device_t dev, struct ow_timing *t) { struct owc_gpiobus_softc *sc; int error; sc = device_get_softc(dev); error = GETBUS(sc); if (error != 0) return (error); critical_enter(); /* Force low */ OUTPIN(sc); LOW(sc); DELAY(t->t_low1); /* Allow resistor to float line high */ INPIN(sc); DELAY(t->t_slot - t->t_low1 + t->t_rec); critical_exit(); RELBUS(sc); return (0); } /* * WRITE-ZERO (see owll_if.m for timings) From Figure 4-2 AN-937 * * |<---------tSLOT------>|<-tREC->| * High RRRRM | | |RRRRRRRM * M | | R M * M| | | |R M * Low MMMMMMMMMMMMMMMMMMMMMR MMMMMM... * |<--15us->| | | * |<------60us--->| | * |<-------tLOW0------>| */ static int owc_gpiobus_write_zero(device_t dev, struct ow_timing *t) { struct owc_gpiobus_softc *sc; int error; sc = device_get_softc(dev); error = GETBUS(sc); if (error != 0) return (error); critical_enter(); /* Force low */ OUTPIN(sc); LOW(sc); DELAY(t->t_low0); /* Allow resistor to float line high */ INPIN(sc); DELAY(t->t_slot - t->t_low0 + t->t_rec); critical_exit(); RELBUS(sc); return (0); } /* * READ-DATA (see owll_if.m for timings) From Figure 4-3 AN-937 * * |<---------tSLOT------>|<-tREC->| * High RRRRM | rrrrrrrrrrrrrrrRRRRRRRM * M | r | R M * M| r | |R M * Low MMMMMMMSSSSSSSSSSSSSSR MMMMMM... * |< sample > | * |<------tRDV---->| | * ->| |<-tRELEASE * * r -- allowed to pull high via the resitor when slave writes a 1-bit * */ static int owc_gpiobus_read_data(device_t dev, struct ow_timing *t, int *bit) { struct owc_gpiobus_softc *sc; int error, sample; sbintime_t then, now; sc = device_get_softc(dev); error = GETBUS(sc); if (error != 0) return (error); critical_enter(); /* Force low for t_lowr microseconds */ then = sbinuptime(); OUTPIN(sc); LOW(sc); DELAY(t->t_lowr); /* * Slave is supposed to hold the line low for t_rdv microseconds for 0 * and immediately float it high for a 1. This is measured from the * master's pushing the line low. */ INPIN(sc); do { now = sbinuptime(); GETPIN(sc, &sample); } while (now - then < (t->t_rdv + 2) * SBT_1US && sample == 0); critical_exit(); if (now - then < t->t_rdv * SBT_1US) *bit = 1; else *bit = 0; /* Wait out the rest of t_slot */ do { now = sbinuptime(); - } while (now - then < t->t_slot * SBT_1US); + } while (now - then < (t->t_slot + t->t_rec) * SBT_1US); RELBUS(sc); return (error); } /* * RESET AND PRESENCE PULSE (see owll_if.m for timings) From Figure 4-4 AN-937 * * |<---------tRSTH------------>| * High RRRM | | RRRRRRRS | RRRR RRM * M | |R| |S | R M * M| R | | S |R M * Low MMMMMMMM MMMMMM| | | SSSSSSSSSS MMMMMM * |<----tRSTL--->| | |<-tPDL---->| * | ->| |<-tR | | * || * * Note: for Regular Speed operations, tRSTL + tR should be less than 960us to * avoid interferring with other devices on the bus */ static int owc_gpiobus_reset_and_presence(device_t dev, struct ow_timing *t, int *bit) { struct owc_gpiobus_softc *sc; int error; int buf = -1; sc = device_get_softc(dev); error = GETBUS(sc); if (error != 0) return (error); /* * Read the current state of the bus. The steady state of an idle bus is * high. Badly wired buses that are missing the required pull up, or * that have a short circuit to ground cause all kinds of mischief when * we try to read them later. Return EIO and release the bus if the bus * is currently low. */ INPIN(sc); GETPIN(sc, &buf); if (buf == 0) { *bit = -1; RELBUS(sc); return (EIO); } critical_enter(); /* Force low */ OUTPIN(sc); LOW(sc); DELAY(t->t_rstl); /* Allow resistor to float line high and then wait for reset pulse */ INPIN(sc); DELAY(t->t_pdh + t->t_pdl / 2); /* Read presence pulse */ GETPIN(sc, &buf); *bit = !!buf; critical_exit(); DELAY(t->t_rsth - (t->t_pdh + t->t_pdl / 2)); /* Timing not critical for this one */ /* * Read the state of the bus after we've waited past the end of the rest * window. It should return to high. If it is low, then we have some * problem and should abort the reset. */ GETPIN(sc, &buf); if (buf == 0) { *bit = -1; RELBUS(sc); return (EIO); } RELBUS(sc); return (0); } static devclass_t owc_gpiobus_devclass; static device_method_t owc_gpiobus_methods[] = { /* Device interface */ #ifdef FDT DEVMETHOD(device_identify, owc_gpiobus_identify), #endif DEVMETHOD(device_probe, owc_gpiobus_probe), DEVMETHOD(device_attach, owc_gpiobus_attach), DEVMETHOD(device_detach, owc_gpiobus_detach), DEVMETHOD(owll_write_one, owc_gpiobus_write_one), DEVMETHOD(owll_write_zero, owc_gpiobus_write_zero), DEVMETHOD(owll_read_data, owc_gpiobus_read_data), DEVMETHOD(owll_reset_and_presence, owc_gpiobus_reset_and_presence), { 0, 0 } }; static driver_t owc_gpiobus_driver = { "owc", owc_gpiobus_methods, sizeof(struct owc_gpiobus_softc), }; DRIVER_MODULE(owc_gpiobus, gpiobus, owc_gpiobus_driver, owc_gpiobus_devclass, 0, 0); MODULE_DEPEND(owc_gpiobus, ow, 1, 1, 1); MODULE_DEPEND(owc_gpiobus, gpiobus, 1, 1, 1); MODULE_VERSION(owc_gpiobus, 1); Index: stable/12 =================================================================== --- stable/12 (revision 354530) +++ stable/12 (revision 354531) Property changes on: stable/12 ___________________________________________________________________ Modified: svn:mergeinfo ## -0,0 +0,1 ## Merged /head:r354077-354078