Index: head/sys/contrib/dev/ath/ath_hal/ar9300/ar9300.h =================================================================== --- head/sys/contrib/dev/ath/ath_hal/ar9300/ar9300.h (revision 334196) +++ head/sys/contrib/dev/ath/ath_hal/ar9300/ar9300.h (revision 334197) @@ -1,1727 +1,1721 @@ /* * Copyright (c) 2013 Qualcomm Atheros, Inc. * * Permission to use, copy, modify, and/or distribute this software for any * purpose with or without fee is hereby granted, provided that the above * copyright notice and this permission notice appear in all copies. * * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES WITH * REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY * AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY SPECIAL, DIRECT, * INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES WHATSOEVER RESULTING FROM * LOSS OF USE, DATA OR PROFITS, WHETHER IN AN ACTION OF CONTRACT, NEGLIGENCE OR * OTHER TORTIOUS ACTION, ARISING OUT OF OR IN CONNECTION WITH THE USE OR * PERFORMANCE OF THIS SOFTWARE. */ #ifndef _ATH_AR9300_H_ #define _ATH_AR9300_H_ #include "ar9300_freebsd_inc.h" #define AH_BIG_ENDIAN 4321 #define AH_LITTLE_ENDIAN 1234 #if _BYTE_ORDER == _BIG_ENDIAN #define AH_BYTE_ORDER AH_BIG_ENDIAN #else #define AH_BYTE_ORDER AH_LITTLE_ENDIAN #endif /* XXX doesn't belong here */ #define AR_EEPROM_MODAL_SPURS 5 /* * (a) this should be N(a), * (b) FreeBSD does define nitems, * (c) it doesn't have an AH_ prefix, sigh. */ #define ARRAY_LENGTH(a) (sizeof(a) / sizeof((a)[0])) #include "ah_internal.h" #include "ah_eeprom.h" #include "ah_devid.h" #include "ar9300eep.h" /* For Eeprom definitions */ #define AR9300_MAGIC 0x19741014 /* MAC register values */ #define INIT_CONFIG_STATUS 0x00000000 #define INIT_RSSI_THR 0x7 /* Missed beacon counter initialized to 0x7 (max is 0xff) */ #define INIT_RSSI_BEACON_WEIGHT 8 /* ave beacon rssi weight (0-16) */ /* * Various fifo fill before Tx start, in 64-byte units * i.e. put the frame in the air while still DMAing */ #define MIN_TX_FIFO_THRESHOLD 0x1 #define MAX_TX_FIFO_THRESHOLD (( 4096 / 64) - 1) #define INIT_TX_FIFO_THRESHOLD MIN_TX_FIFO_THRESHOLD #define CHANSEL_DIV 15 #define FCLK 40 #define COEFF ((FCLK * 5) / 2) #define CHANSEL_2G(_freq) (((_freq) * 0x10000) / CHANSEL_DIV) #define CHANSEL_5G(_freq) (((_freq) * 0x8000) / CHANSEL_DIV) #define CHANSEL_5G_DOT5MHZ 2188 /* * Receive Queue Fifo depth. */ enum RX_FIFO_DEPTH { HAL_HP_RXFIFO_DEPTH = 16, HAL_LP_RXFIFO_DEPTH = 128, }; /* * Gain support. */ #define NUM_CORNER_FIX_BITS_2133 7 #define CCK_OFDM_GAIN_DELTA 15 enum GAIN_PARAMS { GP_TXCLIP, GP_PD90, GP_PD84, GP_GSEL }; enum GAIN_PARAMS_2133 { GP_MIXGAIN_OVR, GP_PWD_138, GP_PWD_137, GP_PWD_136, GP_PWD_132, GP_PWD_131, GP_PWD_130, }; -enum { - HAL_RESET_POWER_ON, - HAL_RESET_WARM, - HAL_RESET_COLD, -}; - typedef struct _gain_opt_step { int16_t paramVal[NUM_CORNER_FIX_BITS_2133]; int32_t stepGain; int8_t stepName[16]; } GAIN_OPTIMIZATION_STEP; typedef struct { u_int32_t numStepsInLadder; u_int32_t defaultStepNum; GAIN_OPTIMIZATION_STEP optStep[10]; } GAIN_OPTIMIZATION_LADDER; typedef struct { u_int32_t currStepNum; u_int32_t currGain; u_int32_t targetGain; u_int32_t loTrig; u_int32_t hiTrig; u_int32_t gainFCorrection; u_int32_t active; GAIN_OPTIMIZATION_STEP *curr_step; } GAIN_VALUES; typedef struct { u_int16_t synth_center; u_int16_t ctl_center; u_int16_t ext_center; } CHAN_CENTERS; /* RF HAL structures */ typedef struct rf_hal_funcs { HAL_BOOL (*set_channel)(struct ath_hal *, struct ieee80211_channel *); HAL_BOOL (*get_chip_power_lim)(struct ath_hal *ah, struct ieee80211_channel *chan); } RF_HAL_FUNCS; struct ar9300_ani_default { u_int16_t m1_thresh_low; u_int16_t m2_thresh_low; u_int16_t m1_thresh; u_int16_t m2_thresh; u_int16_t m2_count_thr; u_int16_t m2_count_thr_low; u_int16_t m1_thresh_low_ext; u_int16_t m2_thresh_low_ext; u_int16_t m1_thresh_ext; u_int16_t m2_thresh_ext; u_int16_t firstep; u_int16_t firstep_low; u_int16_t cycpwr_thr1; u_int16_t cycpwr_thr1_ext; }; /* * Per-channel ANI state private to the driver. */ struct ar9300_ani_state { struct ieee80211_channel c; /* XXX ew? */ HAL_BOOL must_restore; HAL_BOOL ofdms_turn; u_int8_t ofdm_noise_immunity_level; u_int8_t cck_noise_immunity_level; u_int8_t spur_immunity_level; u_int8_t firstep_level; u_int8_t ofdm_weak_sig_detect_off; u_int8_t mrc_cck_off; /* Thresholds */ u_int32_t listen_time; u_int32_t ofdm_trig_high; u_int32_t ofdm_trig_low; int32_t cck_trig_high; int32_t cck_trig_low; int32_t rssi_thr_low; int32_t rssi_thr_high; int32_t rssi; /* The current RSSI */ u_int32_t tx_frame_count; /* Last tx_frame_count */ u_int32_t rx_frame_count; /* Last rx Frame count */ u_int32_t rx_busy_count; /* Last rx busy count */ u_int32_t rx_ext_busy_count; /* Last rx busy count; extension channel */ u_int32_t cycle_count; /* Last cycle_count (can detect wrap-around) */ u_int32_t ofdm_phy_err_count;/* OFDM err count since last reset */ u_int32_t cck_phy_err_count; /* CCK err count since last reset */ struct ar9300_ani_default ini_def; /* INI default values for ANI registers */ HAL_BOOL phy_noise_spur; /* based on OFDM/CCK Phy errors */ }; #define AR9300_ANI_POLLINTERVAL 1000 /* 1000 milliseconds between ANI poll */ #define AR9300_CHANNEL_SWITCH_TIME_USEC 1000 /* 1 millisecond needed to change channels */ #define HAL_PROCESS_ANI 0x00000001 /* ANI state setup */ #define HAL_RADAR_EN 0x80000000 /* Radar detect is capable */ #define HAL_AR_EN 0x40000000 /* AR detect is capable */ #define DO_ANI(ah) \ ((AH9300(ah)->ah_proc_phy_err & HAL_PROCESS_ANI)) #if 0 struct ar9300_stats { u_int32_t ast_ani_niup; /* ANI increased noise immunity */ u_int32_t ast_ani_nidown; /* ANI decreased noise immunity */ u_int32_t ast_ani_spurup; /* ANI increased spur immunity */ u_int32_t ast_ani_spurdown;/* ANI descreased spur immunity */ u_int32_t ast_ani_ofdmon; /* ANI OFDM weak signal detect on */ u_int32_t ast_ani_ofdmoff;/* ANI OFDM weak signal detect off */ u_int32_t ast_ani_cckhigh;/* ANI CCK weak signal threshold high */ u_int32_t ast_ani_ccklow; /* ANI CCK weak signal threshold low */ u_int32_t ast_ani_stepup; /* ANI increased first step level */ u_int32_t ast_ani_stepdown;/* ANI decreased first step level */ u_int32_t ast_ani_ofdmerrs;/* ANI cumulative ofdm phy err count */ u_int32_t ast_ani_cckerrs;/* ANI cumulative cck phy err count */ u_int32_t ast_ani_reset; /* ANI parameters zero'd for non-STA */ u_int32_t ast_ani_lzero; /* ANI listen time forced to zero */ u_int32_t ast_ani_lneg; /* ANI listen time calculated < 0 */ HAL_MIB_STATS ast_mibstats; /* MIB counter stats */ HAL_NODE_STATS ast_nodestats; /* Latest rssi stats from driver */ }; #endif struct ar9300_rad_reader { u_int16_t rd_index; u_int16_t rd_expSeq; u_int32_t rd_resetVal; u_int8_t rd_start; }; struct ar9300_rad_writer { u_int16_t wr_index; u_int16_t wr_seq; }; struct ar9300_radar_event { u_int32_t re_ts; /* 32 bit time stamp */ u_int8_t re_rssi; /* rssi of radar event */ u_int8_t re_dur; /* duration of radar pulse */ u_int8_t re_chanIndex; /* Channel of event */ }; struct ar9300_radar_q_elem { u_int32_t rq_seqNum; u_int32_t rq_busy; /* 32 bit to insure atomic read/write */ struct ar9300_radar_event rq_event; /* Radar event */ }; struct ar9300_radar_q_info { u_int16_t ri_qsize; /* q size */ u_int16_t ri_seqSize; /* Size of sequence ring */ struct ar9300_rad_reader ri_reader; /* State for the q reader */ struct ar9300_rad_writer ri_writer; /* state for the q writer */ }; #define HAL_MAX_ACK_RADAR_DUR 511 #define HAL_MAX_NUM_PEAKS 3 #define HAL_ARQ_SIZE 4096 /* 8K AR events for buffer size */ #define HAL_ARQ_SEQSIZE 4097 /* Sequence counter wrap for AR */ #define HAL_RADARQ_SIZE 1024 /* 1K radar events for buffer size */ #define HAL_RADARQ_SEQSIZE 1025 /* Sequence counter wrap for radar */ #define HAL_NUMRADAR_STATES 64 /* Number of radar channels we keep state for */ struct ar9300_ar_state { u_int16_t ar_prev_time_stamp; u_int32_t ar_prev_width; u_int32_t ar_phy_err_count[HAL_MAX_ACK_RADAR_DUR]; u_int32_t ar_ack_sum; u_int16_t ar_peak_list[HAL_MAX_NUM_PEAKS]; u_int32_t ar_packet_threshold; /* Thresh to determine traffic load */ u_int32_t ar_par_threshold; /* Thresh to determine peak */ u_int32_t ar_radar_rssi; /* Rssi threshold for AR event */ }; struct ar9300_radar_state { struct ieee80211_channel *rs_chan; /* Channel info */ u_int8_t rs_chan_index; /* Channel index in radar structure */ u_int32_t rs_num_radar_events; /* Number of radar events */ int32_t rs_firpwr; /* Thresh to check radar sig is gone */ u_int32_t rs_radar_rssi; /* Thresh to start radar det (dB) */ u_int32_t rs_height; /* Thresh for pulse height (dB)*/ u_int32_t rs_pulse_rssi; /* Thresh to check if pulse is gone (dB) */ u_int32_t rs_inband; /* Thresh to check if pusle is inband (0.5 dB) */ }; typedef struct { u_int8_t uc_receiver_errors; u_int8_t uc_bad_tlp_errors; u_int8_t uc_bad_dllp_errors; u_int8_t uc_replay_timeout_errors; u_int8_t uc_replay_number_rollover_errors; } ar_pcie_error_moniter_counters; #define AR9300_OPFLAGS_11A 0x01 /* if set, allow 11a */ #define AR9300_OPFLAGS_11G 0x02 /* if set, allow 11g */ #define AR9300_OPFLAGS_N_5G_HT40 0x04 /* if set, disable 5G HT40 */ #define AR9300_OPFLAGS_N_2G_HT40 0x08 /* if set, disable 2G HT40 */ #define AR9300_OPFLAGS_N_5G_HT20 0x10 /* if set, disable 5G HT20 */ #define AR9300_OPFLAGS_N_2G_HT20 0x20 /* if set, disable 2G HT20 */ /* * For Kite and later chipsets, the following bits are not being programmed in EEPROM * and so need to be enabled always. * Bit 0: en_fcc_mid, Bit 1: en_jap_mid, Bit 2: en_fcc_dfs_ht40 * Bit 3: en_jap_ht40, Bit 4: en_jap_dfs_ht40 */ #define AR9300_RDEXT_DEFAULT 0x1F #define AR9300_MAX_CHAINS 3 #define AR9300_NUM_CHAINS(chainmask) \ (((chainmask >> 2) & 1) + ((chainmask >> 1) & 1) + (chainmask & 1)) #define AR9300_CHAIN0_MASK 0x1 #define AR9300_CHAIN1_MASK 0x2 #define AR9300_CHAIN2_MASK 0x4 /* Support for multiple INIs */ struct ar9300_ini_array { const u_int32_t *ia_array; u_int32_t ia_rows; u_int32_t ia_columns; }; #define INIT_INI_ARRAY(iniarray, array, rows, columns) do { \ (iniarray)->ia_array = (const u_int32_t *)(array); \ (iniarray)->ia_rows = (rows); \ (iniarray)->ia_columns = (columns); \ } while (0) #define INI_RA(iniarray, row, column) (((iniarray)->ia_array)[(row) * ((iniarray)->ia_columns) + (column)]) #define INIT_CAL(_perCal) \ (_perCal)->cal_state = CAL_WAITING; \ (_perCal)->cal_next = AH_NULL; #define INSERT_CAL(_ahp, _perCal) \ do { \ if ((_ahp)->ah_cal_list_last == AH_NULL) { \ (_ahp)->ah_cal_list = (_ahp)->ah_cal_list_last = (_perCal); \ ((_ahp)->ah_cal_list_last)->cal_next = (_perCal); \ } else { \ ((_ahp)->ah_cal_list_last)->cal_next = (_perCal); \ (_ahp)->ah_cal_list_last = (_perCal); \ (_perCal)->cal_next = (_ahp)->ah_cal_list; \ } \ } while (0) typedef enum cal_types { IQ_MISMATCH_CAL = 0x1, TEMP_COMP_CAL = 0x2, } HAL_CAL_TYPES; typedef enum cal_state { CAL_INACTIVE, CAL_WAITING, CAL_RUNNING, CAL_DONE } HAL_CAL_STATE; /* Calibrate state */ #define MIN_CAL_SAMPLES 1 #define MAX_CAL_SAMPLES 64 #define INIT_LOG_COUNT 5 #define PER_MIN_LOG_COUNT 2 #define PER_MAX_LOG_COUNT 10 #define AR9300_NUM_BT_WEIGHTS 4 #define AR9300_NUM_WLAN_WEIGHTS 4 /* Per Calibration data structure */ typedef struct per_cal_data { HAL_CAL_TYPES cal_type; // Type of calibration u_int32_t cal_num_samples; // Number of SW samples to collect u_int32_t cal_count_max; // Number of HW samples to collect void (*cal_collect)(struct ath_hal *, u_int8_t); // Accumulator func void (*cal_post_proc)(struct ath_hal *, u_int8_t); // Post-processing func } HAL_PERCAL_DATA; /* List structure for calibration data */ typedef struct cal_list { const HAL_PERCAL_DATA *cal_data; HAL_CAL_STATE cal_state; struct cal_list *cal_next; } HAL_CAL_LIST; #define AR9300_NUM_CAL_TYPES 2 #define AR9300_PAPRD_TABLE_SZ 24 #define AR9300_PAPRD_GAIN_TABLE_SZ 32 #define AR9382_MAX_GPIO_PIN_NUM (16) #define AR9382_GPIO_PIN_8_RESERVED (8) #define AR9382_GPIO_9_INPUT_ONLY (9) #define AR9382_MAX_GPIO_INPUT_PIN_NUM (13) #define AR9382_GPIO_PIN_11_RESERVED (11) #define AR9382_MAX_JTAG_GPIO_PIN_NUM (3) /* Paprd tx power adjust data structure */ struct ar9300_paprd_pwr_adjust { u_int32_t target_rate; // rate index u_int32_t reg_addr; // register offset u_int32_t reg_mask; // mask of register u_int32_t reg_mask_offset; // mask offset of register u_int32_t sub_db; // offset value unit of dB }; struct ar9300NfLimits { int16_t max; int16_t min; int16_t nominal; }; #define AR9300_MAX_RATES 36 /* legacy(4) + ofdm(8) + HTSS(8) + HTDS(8) + HTTS(8)*/ struct ath_hal_9300 { struct ath_hal_private ah_priv; /* base class */ /* * Information retrieved from EEPROM. */ ar9300_eeprom_t ah_eeprom; GAIN_VALUES ah_gain_values; u_int8_t ah_macaddr[IEEE80211_ADDR_LEN]; u_int8_t ah_bssid[IEEE80211_ADDR_LEN]; u_int8_t ah_bssid_mask[IEEE80211_ADDR_LEN]; u_int16_t ah_assoc_id; /* * Runtime state. */ u_int32_t ah_mask_reg; /* copy of AR_IMR */ u_int32_t ah_mask2Reg; /* copy of AR_IMR_S2 */ u_int32_t ah_msi_reg; /* copy of AR_PCIE_MSI */ os_atomic_t ah_ier_ref_count; /* reference count for enabling interrupts */ HAL_ANI_STATS ah_stats; /* various statistics */ RF_HAL_FUNCS ah_rf_hal; u_int32_t ah_tx_desc_mask; /* mask for TXDESC */ u_int32_t ah_tx_ok_interrupt_mask; u_int32_t ah_tx_err_interrupt_mask; u_int32_t ah_tx_desc_interrupt_mask; u_int32_t ah_tx_eol_interrupt_mask; u_int32_t ah_tx_urn_interrupt_mask; HAL_TX_QUEUE_INFO ah_txq[HAL_NUM_TX_QUEUES]; HAL_SMPS_MODE ah_sm_power_mode; HAL_BOOL ah_chip_full_sleep; u_int32_t ah_atim_window; HAL_ANT_SETTING ah_diversity_control; /* antenna setting */ u_int16_t ah_antenna_switch_swap; /* Controls mapping of OID request */ u_int8_t ah_tx_chainmask_cfg; /* chain mask config */ u_int8_t ah_rx_chainmask_cfg; u_int32_t ah_beacon_rssi_threshold; /* cache beacon rssi threshold */ /* Calibration related fields */ HAL_CAL_TYPES ah_supp_cals; HAL_CAL_LIST ah_iq_cal_data; /* IQ Cal Data */ HAL_CAL_LIST ah_temp_comp_cal_data; /* Temperature Compensation Cal Data */ HAL_CAL_LIST *ah_cal_list; /* ptr to first cal in list */ HAL_CAL_LIST *ah_cal_list_last; /* ptr to last cal in list */ HAL_CAL_LIST *ah_cal_list_curr; /* ptr to current cal */ // IQ Cal aliases #define ah_total_power_meas_i ah_meas0.unsign #define ah_total_power_meas_q ah_meas1.unsign #define ah_total_iq_corr_meas ah_meas2.sign union { u_int32_t unsign[AR9300_MAX_CHAINS]; int32_t sign[AR9300_MAX_CHAINS]; } ah_meas0; union { u_int32_t unsign[AR9300_MAX_CHAINS]; int32_t sign[AR9300_MAX_CHAINS]; } ah_meas1; union { u_int32_t unsign[AR9300_MAX_CHAINS]; int32_t sign[AR9300_MAX_CHAINS]; } ah_meas2; union { u_int32_t unsign[AR9300_MAX_CHAINS]; int32_t sign[AR9300_MAX_CHAINS]; } ah_meas3; u_int16_t ah_cal_samples; /* end - Calibration related fields */ u_int32_t ah_tx6_power_in_half_dbm; /* power output for 6Mb tx */ u_int32_t ah_sta_id1_defaults; /* STA_ID1 default settings */ u_int32_t ah_misc_mode; /* MISC_MODE settings */ HAL_BOOL ah_get_plcp_hdr; /* setting about MISC_SEL_EVM */ enum { AUTO_32KHZ, /* use it if 32kHz crystal present */ USE_32KHZ, /* do it regardless */ DONT_USE_32KHZ, /* don't use it regardless */ } ah_enable32k_hz_clock; /* whether to sleep at 32kHz */ u_int32_t ah_ofdm_tx_power; int16_t ah_tx_power_index_offset; u_int ah_slot_time; /* user-specified slot time */ u_int ah_ack_timeout; /* user-specified ack timeout */ /* * XXX * 11g-specific stuff; belongs in the driver. */ u_int8_t ah_g_beacon_rate; /* fixed rate for G beacons */ u_int32_t ah_gpio_mask; /* copy of enabled GPIO mask */ u_int32_t ah_gpio_cause; /* copy of GPIO cause (sync and async) */ /* * RF Silent handling; setup according to the EEPROM. */ u_int32_t ah_gpio_select; /* GPIO pin to use */ u_int32_t ah_polarity; /* polarity to disable RF */ u_int32_t ah_gpio_bit; /* after init, prev value */ HAL_BOOL ah_eep_enabled; /* EEPROM bit for capability */ #ifdef ATH_BT_COEX /* * Bluetooth coexistence static setup according to the registry */ HAL_BT_MODULE ah_bt_module; /* Bluetooth module identifier */ u_int8_t ah_bt_coex_config_type; /* BT coex configuration */ u_int8_t ah_bt_active_gpio_select; /* GPIO pin for BT_ACTIVE */ u_int8_t ah_bt_priority_gpio_select; /* GPIO pin for BT_PRIORITY */ u_int8_t ah_wlan_active_gpio_select; /* GPIO pin for WLAN_ACTIVE */ u_int8_t ah_bt_active_polarity; /* Polarity of BT_ACTIVE */ HAL_BOOL ah_bt_coex_single_ant; /* Single or dual antenna configuration */ u_int8_t ah_bt_wlan_isolation; /* Isolation between BT and WLAN in dB */ /* * Bluetooth coexistence runtime settings */ HAL_BOOL ah_bt_coex_enabled; /* If Bluetooth coexistence is enabled */ u_int32_t ah_bt_coex_mode; /* Register setting for AR_BT_COEX_MODE */ u_int32_t ah_bt_coex_bt_weight[AR9300_NUM_BT_WEIGHTS]; /* Register setting for AR_BT_COEX_WEIGHT */ u_int32_t ah_bt_coex_wlan_weight[AR9300_NUM_WLAN_WEIGHTS]; /* Register setting for AR_BT_COEX_WEIGHT */ u_int32_t ah_bt_coex_mode2; /* Register setting for AR_BT_COEX_MODE2 */ u_int32_t ah_bt_coex_flag; /* Special tuning flags for BT coex */ #endif /* * Generic timer support */ u_int32_t ah_avail_gen_timers; /* mask of available timers */ u_int32_t ah_intr_gen_timer_trigger; /* generic timer trigger interrupt state */ u_int32_t ah_intr_gen_timer_thresh; /* generic timer trigger interrupt state */ HAL_BOOL ah_enable_tsf2; /* enable TSF2 for gen timer 8-15. */ /* * ANI & Radar support. */ u_int32_t ah_proc_phy_err; /* Process Phy errs */ u_int32_t ah_ani_period; /* ani update list period */ struct ar9300_ani_state *ah_curani; /* cached last reference */ struct ar9300_ani_state ah_ani[255]; /* per-channel state */ struct ar9300_radar_state ah_radar[HAL_NUMRADAR_STATES]; /* Per-Channel Radar detector state */ struct ar9300_radar_q_elem *ah_radarq; /* radar event queue */ struct ar9300_radar_q_info ah_radarq_info; /* radar event q read/write state */ struct ar9300_ar_state ah_ar; /* AR detector state */ struct ar9300_radar_q_elem *ah_arq; /* AR event queue */ struct ar9300_radar_q_info ah_arq_info; /* AR event q read/write state */ /* * Transmit power state. Note these are maintained * here so they can be retrieved by diagnostic tools. */ u_int16_t ah_rates_array[16]; /* * Tx queue interrupt state. */ u_int32_t ah_intr_txqs; HAL_BOOL ah_intr_mitigation_rx; /* rx Interrupt Mitigation Settings */ HAL_BOOL ah_intr_mitigation_tx; /* tx Interrupt Mitigation Settings */ /* * Extension Channel Rx Clear State */ u_int32_t ah_cycle_count; u_int32_t ah_ctl_busy; u_int32_t ah_ext_busy; /* HT CWM state */ HAL_HT_EXTPROTSPACING ah_ext_prot_spacing; u_int8_t ah_tx_chainmask; /* tx chain mask */ u_int8_t ah_rx_chainmask; /* rx chain mask */ /* optional tx chainmask */ u_int8_t ah_tx_chainmaskopt; u_int8_t ah_tx_cal_chainmask; /* tx cal chain mask */ u_int8_t ah_rx_cal_chainmask; /* rx cal chain mask */ int ah_hwp; void *ah_cal_mem; HAL_BOOL ah_emu_eeprom; HAL_ANI_CMD ah_ani_function; HAL_BOOL ah_rifs_enabled; u_int32_t ah_rifs_reg[11]; u_int32_t ah_rifs_sec_cnt; /* open-loop power control */ u_int32_t original_gain[22]; int32_t init_pdadc; int32_t pdadc_delta; /* cycle counts for beacon stuck diagnostics */ u_int32_t ah_cycles; u_int32_t ah_rx_clear; u_int32_t ah_rx_frame; u_int32_t ah_tx_frame; #define BB_HANG_SIG1 0 #define BB_HANG_SIG2 1 #define BB_HANG_SIG3 2 #define BB_HANG_SIG4 3 #define MAC_HANG_SIG1 4 #define MAC_HANG_SIG2 5 /* bb hang detection */ int ah_hang[6]; hal_hw_hangs_t ah_hang_wars; /* * Keytable type table */ #define AR_KEYTABLE_SIZE 128 /* XXX! */ uint8_t ah_keytype[AR_KEYTABLE_SIZE]; #undef AR_KEYTABLE_SIZE /* * Support for ar9300 multiple INIs */ struct ar9300_ini_array ah_ini_pcie_serdes; struct ar9300_ini_array ah_ini_pcie_serdes_low_power; struct ar9300_ini_array ah_ini_modes_additional; struct ar9300_ini_array ah_ini_modes_additional_40mhz; struct ar9300_ini_array ah_ini_modes_rxgain; struct ar9300_ini_array ah_ini_modes_rxgain_bounds; struct ar9300_ini_array ah_ini_modes_txgain; struct ar9300_ini_array ah_ini_japan2484; struct ar9300_ini_array ah_ini_radio_post_sys2ant; struct ar9300_ini_array ah_ini_BTCOEX_MAX_TXPWR; struct ar9300_ini_array ah_ini_modes_rxgain_xlna; struct ar9300_ini_array ah_ini_modes_rxgain_bb_core; struct ar9300_ini_array ah_ini_modes_rxgain_bb_postamble; /* * New INI format starting with Osprey 2.0 INI. * Pre, core, post arrays for each sub-system (mac, bb, radio, soc) */ #define ATH_INI_PRE 0 #define ATH_INI_CORE 1 #define ATH_INI_POST 2 #define ATH_INI_NUM_SPLIT (ATH_INI_POST + 1) struct ar9300_ini_array ah_ini_mac[ATH_INI_NUM_SPLIT]; /* New INI format */ struct ar9300_ini_array ah_ini_bb[ATH_INI_NUM_SPLIT]; /* New INI format */ struct ar9300_ini_array ah_ini_radio[ATH_INI_NUM_SPLIT]; /* New INI format */ struct ar9300_ini_array ah_ini_soc[ATH_INI_NUM_SPLIT]; /* New INI format */ /* * Added to support DFS postamble array in INI that we need to apply * in DFS channels */ struct ar9300_ini_array ah_ini_dfs; #if ATH_WOW struct ar9300_ini_array ah_ini_pcie_serdes_wow; /* SerDes values during WOW sleep */ #endif /* To indicate EEPROM mapping used */ u_int32_t ah_immunity_vals[6]; HAL_BOOL ah_immunity_on; /* * snap shot of counter register for debug purposes */ #ifdef AH_DEBUG u_int32_t last_tf; u_int32_t last_rf; u_int32_t last_rc; u_int32_t last_cc; #endif HAL_BOOL ah_dma_stuck; /* Set to AH_TRUE when RX/TX DMA failed to stop. */ u_int32_t nf_tsf32; /* timestamp for NF calibration duration */ u_int32_t reg_dmn; /* Regulatory Domain */ int16_t twice_antenna_gain; /* Antenna Gain */ u_int16_t twice_antenna_reduction; /* Antenna Gain Allowed */ /* * Upper limit after factoring in the regulatory max, antenna gain and * multichain factor. No TxBF, CDD or STBC gain factored */ int16_t upper_limit[AR9300_MAX_CHAINS]; /* adjusted power for descriptor-based TPC for 1, 2, or 3 chains */ int16_t txpower[AR9300_MAX_RATES][AR9300_MAX_CHAINS]; /* adjusted power for descriptor-based TPC for 1, 2, or 3 chains with STBC*/ int16_t txpower_stbc[AR9300_MAX_RATES][AR9300_MAX_CHAINS]; /* Transmit Status ring support */ struct ar9300_txs *ts_ring; u_int16_t ts_tail; u_int16_t ts_size; u_int32_t ts_paddr_start; u_int32_t ts_paddr_end; /* Receive Buffer size */ #define HAL_RXBUFSIZE_DEFAULT 0xfff u_int16_t rx_buf_size; u_int32_t ah_wa_reg_val; // Store the permanent value of Reg 0x4004 so we dont have to R/M/W. (We should not be reading this register when in sleep states). /* Indicate the PLL source clock rate is 25Mhz or not. * clk_25mhz = 0 by default. */ u_int8_t clk_25mhz; /* For PAPRD uses */ u_int16_t small_signal_gain[AH_MAX_CHAINS]; u_int32_t pa_table[AH_MAX_CHAINS][AR9300_PAPRD_TABLE_SZ]; u_int32_t paprd_gain_table_entries[AR9300_PAPRD_GAIN_TABLE_SZ]; u_int32_t paprd_gain_table_index[AR9300_PAPRD_GAIN_TABLE_SZ]; u_int32_t ah_2g_paprd_rate_mask_ht20; /* Copy of eep->modal_header_2g.paprd_rate_mask_ht20 */ u_int32_t ah_2g_paprd_rate_mask_ht40; /* Copy of eep->modal_header_2g.paprd_rate_mask_ht40 */ u_int32_t ah_5g_paprd_rate_mask_ht20; /* Copy of eep->modal_header_5g.paprd_rate_mask_ht20 */ u_int32_t ah_5g_paprd_rate_mask_ht40; /* Copy of eep->modal_header_5g.paprd_rate_mask_ht40 */ u_int32_t paprd_training_power; /* For GreenTx use to store the default tx power */ u_int8_t ah_default_tx_power[ar9300_rate_size]; HAL_BOOL ah_paprd_broken; /* To store offsets of host interface registers */ struct { u_int32_t AR_RC; u_int32_t AR_WA; u_int32_t AR_PM_STATE; u_int32_t AR_H_INFOL; u_int32_t AR_H_INFOH; u_int32_t AR_PCIE_PM_CTRL; u_int32_t AR_HOST_TIMEOUT; u_int32_t AR_EEPROM; u_int32_t AR_SREV; u_int32_t AR_INTR_SYNC_CAUSE; u_int32_t AR_INTR_SYNC_CAUSE_CLR; u_int32_t AR_INTR_SYNC_ENABLE; u_int32_t AR_INTR_ASYNC_MASK; u_int32_t AR_INTR_SYNC_MASK; u_int32_t AR_INTR_ASYNC_CAUSE_CLR; u_int32_t AR_INTR_ASYNC_CAUSE; u_int32_t AR_INTR_ASYNC_ENABLE; u_int32_t AR_PCIE_SERDES; u_int32_t AR_PCIE_SERDES2; u_int32_t AR_GPIO_OUT; u_int32_t AR_GPIO_IN; u_int32_t AR_GPIO_OE_OUT; u_int32_t AR_GPIO_OE1_OUT; u_int32_t AR_GPIO_INTR_POL; u_int32_t AR_GPIO_INPUT_EN_VAL; u_int32_t AR_GPIO_INPUT_MUX1; u_int32_t AR_GPIO_INPUT_MUX2; u_int32_t AR_GPIO_OUTPUT_MUX1; u_int32_t AR_GPIO_OUTPUT_MUX2; u_int32_t AR_GPIO_OUTPUT_MUX3; u_int32_t AR_INPUT_STATE; u_int32_t AR_SPARE; u_int32_t AR_PCIE_CORE_RESET_EN; u_int32_t AR_CLKRUN; u_int32_t AR_EEPROM_STATUS_DATA; u_int32_t AR_OBS; u_int32_t AR_RFSILENT; u_int32_t AR_GPIO_PDPU; u_int32_t AR_GPIO_DS; u_int32_t AR_MISC; u_int32_t AR_PCIE_MSI; u_int32_t AR_TSF_SNAPSHOT_BT_ACTIVE; u_int32_t AR_TSF_SNAPSHOT_BT_PRIORITY; u_int32_t AR_TSF_SNAPSHOT_BT_CNTL; u_int32_t AR_PCIE_PHY_LATENCY_NFTS_ADJ; u_int32_t AR_TDMA_CCA_CNTL; u_int32_t AR_TXAPSYNC; u_int32_t AR_TXSYNC_INIT_SYNC_TMR; u_int32_t AR_INTR_PRIO_SYNC_CAUSE; u_int32_t AR_INTR_PRIO_SYNC_ENABLE; u_int32_t AR_INTR_PRIO_ASYNC_MASK; u_int32_t AR_INTR_PRIO_SYNC_MASK; u_int32_t AR_INTR_PRIO_ASYNC_CAUSE; u_int32_t AR_INTR_PRIO_ASYNC_ENABLE; } ah_hostifregs; u_int32_t ah_enterprise_mode; u_int32_t ah_radar1; u_int32_t ah_dc_offset; HAL_BOOL ah_hw_green_tx_enable; /* 1:enalbe H/W Green Tx */ HAL_BOOL ah_smartantenna_enable; /* 1:enalbe H/W */ u_int32_t ah_disable_cck; HAL_BOOL ah_lna_div_use_bt_ant_enable; /* 1:enable Rx(LNA) Diversity */ /* * Different types of memory where the calibration data might be stored. * All types are searched in Ar9300EepromRestore() in the order flash, eeprom, otp. * To disable searching a type, set its parameter to 0. */ int try_dram; int try_flash; int try_eeprom; int try_otp; #ifdef ATH_CAL_NAND_FLASH int try_nand; #endif /* * This is where we found the calibration data. */ int calibration_data_source; int calibration_data_source_address; /* * This is where we look for the calibration data. must be set before ath_attach() is called */ int calibration_data_try; int calibration_data_try_address; u_int8_t tx_iq_cal_enable : 1, tx_iq_cal_during_agc_cal : 1, tx_cl_cal_enable : 1; #if ATH_SUPPORT_MCI /* For MCI */ HAL_BOOL ah_mci_ready; u_int32_t ah_mci_int_raw; u_int32_t ah_mci_int_rx_msg; u_int32_t ah_mci_rx_status; u_int32_t ah_mci_cont_status; u_int8_t ah_mci_bt_state; u_int32_t ah_mci_gpm_addr; u_int8_t *ah_mci_gpm_buf; u_int32_t ah_mci_gpm_len; u_int32_t ah_mci_gpm_idx; u_int32_t ah_mci_sched_addr; u_int8_t *ah_mci_sched_buf; u_int8_t ah_mci_coex_major_version_wlan; u_int8_t ah_mci_coex_minor_version_wlan; u_int8_t ah_mci_coex_major_version_bt; u_int8_t ah_mci_coex_minor_version_bt; HAL_BOOL ah_mci_coex_bt_version_known; HAL_BOOL ah_mci_coex_wlan_channels_update; u_int32_t ah_mci_coex_wlan_channels[4]; HAL_BOOL ah_mci_coex_2g5g_update; HAL_BOOL ah_mci_coex_is_2g; HAL_BOOL ah_mci_query_bt; HAL_BOOL ah_mci_unhalt_bt_gpm; /* need send UNHALT */ HAL_BOOL ah_mci_halted_bt_gpm; /* HALT sent */ HAL_BOOL ah_mci_need_flush_btinfo; HAL_BOOL ah_mci_concur_tx_en; u_int8_t ah_mci_stomp_low_tx_pri; u_int8_t ah_mci_stomp_all_tx_pri; u_int8_t ah_mci_stomp_none_tx_pri; u_int32_t ah_mci_wlan_cal_seq; u_int32_t ah_mci_wlan_cal_done; #if ATH_SUPPORT_AIC HAL_BOOL ah_aic_enabled; u_int32_t ah_aic_sram[ATH_AIC_MAX_BT_CHANNEL]; #endif #endif /* ATH_SUPPORT_MCI */ u_int8_t ah_cac_quiet_enabled; #if ATH_WOW_OFFLOAD u_int32_t ah_mcast_filter_l32_set; u_int32_t ah_mcast_filter_u32_set; #endif HAL_BOOL ah_reduced_self_gen_mask; HAL_BOOL ah_chip_reset_done; HAL_BOOL ah_abort_txdma_norx; /* store previous passive RX Cal info */ HAL_BOOL ah_skip_rx_iq_cal; HAL_BOOL ah_rx_cal_complete; /* previous rx cal completed or not */ u_int32_t ah_rx_cal_chan; /* chan on which rx cal is done */ u_int32_t ah_rx_cal_chan_flag; u_int32_t ah_rx_cal_corr[AR9300_MAX_CHAINS]; /* Local additions for FreeBSD */ /* * These fields are in the top level HAL in the atheros * codebase; here we place them in the AR9300 HAL and * access them via accessor methods if the driver requires them. */ u_int32_t ah_ob_db1[3]; u_int32_t ah_db2[3]; u_int32_t ah_bb_panic_timeout_ms; u_int32_t ah_bb_panic_last_status; u_int32_t ah_tx_trig_level; u_int16_t ath_hal_spur_chans[AR_EEPROM_MODAL_SPURS][2]; int16_t nf_cw_int_delta; /* diff btwn nominal NF and CW interf threshold */ int ah_phyrestart_disabled; HAL_RSSI_TX_POWER green_tx_status; int green_ap_ps_on; int ah_enable_keysearch_always; int ah_fccaifs; int ah_reset_reason; int ah_dcs_enable; HAL_ANI_STATE ext_ani_state; /* FreeBSD; external facing ANI state */ struct ar9300NfLimits nf_2GHz; struct ar9300NfLimits nf_5GHz; struct ar9300NfLimits *nfp; uint32_t ah_beaconInterval; }; #define AH9300(_ah) ((struct ath_hal_9300 *)(_ah)) #define IS_9300_EMU(ah) \ (AH_PRIVATE(ah)->ah_devid == AR9300_DEVID_EMU_PCIE) #define ar9300_eep_data_in_flash(_ah) \ (!(AH_PRIVATE(_ah)->ah_flags & AH_USE_EEPROM)) #ifdef notyet // Need these additional conditions for IS_5GHZ_FAST_CLOCK_EN when we have valid eeprom contents. && \ ((ar9300_eeprom_get(AH9300(_ah), EEP_MINOR_REV) <= AR9300_EEP_MINOR_VER_16) || \ (ar9300_eeprom_get(AH9300(_ah), EEP_FSTCLK_5G)))) #endif /* * WAR for bug 6773. OS_DELAY() does a PIO READ on the PCI bus which allows * other cards' DMA reads to complete in the middle of our reset. */ #define WAR_6773(x) do { \ if ((++(x) % 64) == 0) \ OS_DELAY(1); \ } while (0) #define REG_WRITE_ARRAY(iniarray, column, regWr) do { \ int r; \ for (r = 0; r < ((iniarray)->ia_rows); r++) { \ OS_REG_WRITE(ah, INI_RA((iniarray), (r), 0), INI_RA((iniarray), r, (column)));\ WAR_6773(regWr); \ } \ } while (0) #define UPPER_5G_SUB_BANDSTART 5700 #define MID_5G_SUB_BANDSTART 5400 #define TRAINPOWER_DB_OFFSET 6 #define AH_PAPRD_GET_SCALE_FACTOR(_scale, _eep, _is2G, _channel) do{ if(_is2G) { _scale = (_eep->modal_header_2g.paprd_rate_mask_ht20>>25)&0x7; \ } else { \ if(_channel >= UPPER_5G_SUB_BANDSTART){ _scale = (_eep->modal_header_5g.paprd_rate_mask_ht20>>25)&0x7;} \ else if((UPPER_5G_SUB_BANDSTART < _channel) && (_channel >= MID_5G_SUB_BANDSTART)) \ { _scale = (_eep->modal_header_5g.paprd_rate_mask_ht40>>28)&0x7;} \ else { _scale = (_eep->modal_header_5g.paprd_rate_mask_ht40>>25)&0x7;} } }while(0) #ifdef AH_ASSERT #define ar9300FeatureNotSupported(feature, ah, func) \ ath_hal_printf(ah, # feature \ " not supported but called from %s\n", (func)), \ hal_assert(0) #else #define ar9300FeatureNotSupported(feature, ah, func) \ ath_hal_printf(ah, # feature \ " not supported but called from %s\n", (func)) #endif /* AH_ASSERT */ /* * Green Tx, Based on different RSSI of Received Beacon thresholds, * using different tx power by modified register tx power related values. * The thresholds are decided by system team. */ #define WB225_SW_GREEN_TX_THRES1_DB 56 /* in dB */ #define WB225_SW_GREEN_TX_THRES2_DB 41 /* in dB */ #define WB225_OB_CALIBRATION_VALUE 5 /* For Green Tx OLPC Delta Calibration Offset */ #define WB225_OB_GREEN_TX_SHORT_VALUE 1 /* For Green Tx OB value in short distance*/ #define WB225_OB_GREEN_TX_MIDDLE_VALUE 3 /* For Green Tx OB value in middle distance */ #define WB225_OB_GREEN_TX_LONG_VALUE 5 /* For Green Tx OB value in long distance */ #define WB225_BBPWRTXRATE9_SW_GREEN_TX_SHORT_VALUE 0x06060606 /* For SwGreen Tx BB_powertx_rate9 reg value in short distance */ #define WB225_BBPWRTXRATE9_SW_GREEN_TX_MIDDLE_VALUE 0x0E0E0E0E /* For SwGreen Tx BB_powertx_rate9 reg value in middle distance */ /* Tx power for short distacnce in SwGreenTx.*/ static const u_int8_t wb225_sw_gtx_tp_distance_short[ar9300_rate_size] = { 6, /*ALL_TARGET_LEGACY_6_24*/ 6, /*ALL_TARGET_LEGACY_36*/ 6, /*ALL_TARGET_LEGACY_48*/ 4, /*ALL_TARGET_LEGACY_54*/ 6, /*ALL_TARGET_LEGACY_1L_5L*/ 6, /*ALL_TARGET_LEGACY_5S*/ 6, /*ALL_TARGET_LEGACY_11L*/ 6, /*ALL_TARGET_LEGACY_11S*/ 6, /*ALL_TARGET_HT20_0_8_16*/ 6, /*ALL_TARGET_HT20_1_3_9_11_17_19*/ 4, /*ALL_TARGET_HT20_4*/ 4, /*ALL_TARGET_HT20_5*/ 4, /*ALL_TARGET_HT20_6*/ 2, /*ALL_TARGET_HT20_7*/ 0, /*ALL_TARGET_HT20_12*/ 0, /*ALL_TARGET_HT20_13*/ 0, /*ALL_TARGET_HT20_14*/ 0, /*ALL_TARGET_HT20_15*/ 0, /*ALL_TARGET_HT20_20*/ 0, /*ALL_TARGET_HT20_21*/ 0, /*ALL_TARGET_HT20_22*/ 0, /*ALL_TARGET_HT20_23*/ 6, /*ALL_TARGET_HT40_0_8_16*/ 6, /*ALL_TARGET_HT40_1_3_9_11_17_19*/ 4, /*ALL_TARGET_HT40_4*/ 4, /*ALL_TARGET_HT40_5*/ 4, /*ALL_TARGET_HT40_6*/ 2, /*ALL_TARGET_HT40_7*/ 0, /*ALL_TARGET_HT40_12*/ 0, /*ALL_TARGET_HT40_13*/ 0, /*ALL_TARGET_HT40_14*/ 0, /*ALL_TARGET_HT40_15*/ 0, /*ALL_TARGET_HT40_20*/ 0, /*ALL_TARGET_HT40_21*/ 0, /*ALL_TARGET_HT40_22*/ 0 /*ALL_TARGET_HT40_23*/ }; /* Tx power for middle distacnce in SwGreenTx.*/ static const u_int8_t wb225_sw_gtx_tp_distance_middle[ar9300_rate_size] = { 14, /*ALL_TARGET_LEGACY_6_24*/ 14, /*ALL_TARGET_LEGACY_36*/ 14, /*ALL_TARGET_LEGACY_48*/ 12, /*ALL_TARGET_LEGACY_54*/ 14, /*ALL_TARGET_LEGACY_1L_5L*/ 14, /*ALL_TARGET_LEGACY_5S*/ 14, /*ALL_TARGET_LEGACY_11L*/ 14, /*ALL_TARGET_LEGACY_11S*/ 14, /*ALL_TARGET_HT20_0_8_16*/ 14, /*ALL_TARGET_HT20_1_3_9_11_17_19*/ 14, /*ALL_TARGET_HT20_4*/ 14, /*ALL_TARGET_HT20_5*/ 12, /*ALL_TARGET_HT20_6*/ 10, /*ALL_TARGET_HT20_7*/ 0, /*ALL_TARGET_HT20_12*/ 0, /*ALL_TARGET_HT20_13*/ 0, /*ALL_TARGET_HT20_14*/ 0, /*ALL_TARGET_HT20_15*/ 0, /*ALL_TARGET_HT20_20*/ 0, /*ALL_TARGET_HT20_21*/ 0, /*ALL_TARGET_HT20_22*/ 0, /*ALL_TARGET_HT20_23*/ 14, /*ALL_TARGET_HT40_0_8_16*/ 14, /*ALL_TARGET_HT40_1_3_9_11_17_19*/ 14, /*ALL_TARGET_HT40_4*/ 14, /*ALL_TARGET_HT40_5*/ 12, /*ALL_TARGET_HT40_6*/ 10, /*ALL_TARGET_HT40_7*/ 0, /*ALL_TARGET_HT40_12*/ 0, /*ALL_TARGET_HT40_13*/ 0, /*ALL_TARGET_HT40_14*/ 0, /*ALL_TARGET_HT40_15*/ 0, /*ALL_TARGET_HT40_20*/ 0, /*ALL_TARGET_HT40_21*/ 0, /*ALL_TARGET_HT40_22*/ 0 /*ALL_TARGET_HT40_23*/ }; /* OLPC DeltaCalibration Offset unit in half dB.*/ static const u_int8_t wb225_gtx_olpc_cal_offset[6] = { 0, /* OB0*/ 16, /* OB1*/ 9, /* OB2*/ 5, /* OB3*/ 2, /* OB4*/ 0, /* OB5*/ }; /* * Definitions for HwGreenTx */ #define AR9485_HW_GREEN_TX_THRES1_DB 56 /* in dB */ #define AR9485_HW_GREEN_TX_THRES2_DB 41 /* in dB */ #define AR9485_BBPWRTXRATE9_HW_GREEN_TX_SHORT_VALUE 0x0C0C0A0A /* For HwGreen Tx BB_powertx_rate9 reg value in short distance */ #define AR9485_BBPWRTXRATE9_HW_GREEN_TX_MIDDLE_VALUE 0x10100E0E /* For HwGreenTx BB_powertx_rate9 reg value in middle distance */ /* Tx power for short distacnce in HwGreenTx.*/ static const u_int8_t ar9485_hw_gtx_tp_distance_short[ar9300_rate_size] = { 14, /*ALL_TARGET_LEGACY_6_24*/ 14, /*ALL_TARGET_LEGACY_36*/ 8, /*ALL_TARGET_LEGACY_48*/ 2, /*ALL_TARGET_LEGACY_54*/ 14, /*ALL_TARGET_LEGACY_1L_5L*/ 14, /*ALL_TARGET_LEGACY_5S*/ 14, /*ALL_TARGET_LEGACY_11L*/ 14, /*ALL_TARGET_LEGACY_11S*/ 12, /*ALL_TARGET_HT20_0_8_16*/ 12, /*ALL_TARGET_HT20_1_3_9_11_17_19*/ 12, /*ALL_TARGET_HT20_4*/ 12, /*ALL_TARGET_HT20_5*/ 8, /*ALL_TARGET_HT20_6*/ 2, /*ALL_TARGET_HT20_7*/ 0, /*ALL_TARGET_HT20_12*/ 0, /*ALL_TARGET_HT20_13*/ 0, /*ALL_TARGET_HT20_14*/ 0, /*ALL_TARGET_HT20_15*/ 0, /*ALL_TARGET_HT20_20*/ 0, /*ALL_TARGET_HT20_21*/ 0, /*ALL_TARGET_HT20_22*/ 0, /*ALL_TARGET_HT20_23*/ 10, /*ALL_TARGET_HT40_0_8_16*/ 10, /*ALL_TARGET_HT40_1_3_9_11_17_19*/ 10, /*ALL_TARGET_HT40_4*/ 10, /*ALL_TARGET_HT40_5*/ 6, /*ALL_TARGET_HT40_6*/ 2, /*ALL_TARGET_HT40_7*/ 0, /*ALL_TARGET_HT40_12*/ 0, /*ALL_TARGET_HT40_13*/ 0, /*ALL_TARGET_HT40_14*/ 0, /*ALL_TARGET_HT40_15*/ 0, /*ALL_TARGET_HT40_20*/ 0, /*ALL_TARGET_HT40_21*/ 0, /*ALL_TARGET_HT40_22*/ 0 /*ALL_TARGET_HT40_23*/ }; /* Tx power for middle distacnce in HwGreenTx.*/ static const u_int8_t ar9485_hw_gtx_tp_distance_middle[ar9300_rate_size] = { 18, /*ALL_TARGET_LEGACY_6_24*/ 18, /*ALL_TARGET_LEGACY_36*/ 14, /*ALL_TARGET_LEGACY_48*/ 12, /*ALL_TARGET_LEGACY_54*/ 18, /*ALL_TARGET_LEGACY_1L_5L*/ 18, /*ALL_TARGET_LEGACY_5S*/ 18, /*ALL_TARGET_LEGACY_11L*/ 18, /*ALL_TARGET_LEGACY_11S*/ 16, /*ALL_TARGET_HT20_0_8_16*/ 16, /*ALL_TARGET_HT20_1_3_9_11_17_19*/ 16, /*ALL_TARGET_HT20_4*/ 16, /*ALL_TARGET_HT20_5*/ 14, /*ALL_TARGET_HT20_6*/ 12, /*ALL_TARGET_HT20_7*/ 0, /*ALL_TARGET_HT20_12*/ 0, /*ALL_TARGET_HT20_13*/ 0, /*ALL_TARGET_HT20_14*/ 0, /*ALL_TARGET_HT20_15*/ 0, /*ALL_TARGET_HT20_20*/ 0, /*ALL_TARGET_HT20_21*/ 0, /*ALL_TARGET_HT20_22*/ 0, /*ALL_TARGET_HT20_23*/ 14, /*ALL_TARGET_HT40_0_8_16*/ 14, /*ALL_TARGET_HT40_1_3_9_11_17_19*/ 14, /*ALL_TARGET_HT40_4*/ 14, /*ALL_TARGET_HT40_5*/ 14, /*ALL_TARGET_HT40_6*/ 12, /*ALL_TARGET_HT40_7*/ 0, /*ALL_TARGET_HT40_12*/ 0, /*ALL_TARGET_HT40_13*/ 0, /*ALL_TARGET_HT40_14*/ 0, /*ALL_TARGET_HT40_15*/ 0, /*ALL_TARGET_HT40_20*/ 0, /*ALL_TARGET_HT40_21*/ 0, /*ALL_TARGET_HT40_22*/ 0 /*ALL_TARGET_HT40_23*/ }; /* MIMO Modes used in TPC calculations */ typedef enum { AR9300_DEF_MODE = 0, /* Could be CDD or Direct */ AR9300_TXBF_MODE, AR9300_STBC_MODE } AR9300_TXMODES; typedef enum { POSEIDON_STORED_REG_OBDB = 0, /* default OB/DB setting from ini */ POSEIDON_STORED_REG_TPC = 1, /* default txpower value in TPC reg */ POSEIDON_STORED_REG_BB_PWRTX_RATE9 = 2, /* default txpower value in * BB_powertx_rate9 reg */ POSEIDON_STORED_REG_SZ /* Can not add anymore */ } POSEIDON_STORED_REGS; typedef enum { POSEIDON_STORED_REG_G2_OLPC_OFFSET = 0,/* default OB/DB setting from ini */ POSEIDON_STORED_REG_G2_SZ /* should not exceed 3 */ } POSEIDON_STORED_REGS_G2; #if AH_NEED_TX_DATA_SWAP #if AH_NEED_RX_DATA_SWAP #define ar9300_init_cfg_reg(ah) OS_REG_RMW(ah, AR_CFG, AR_CFG_SWTB | AR_CFG_SWRB,0) #else #define ar9300_init_cfg_reg(ah) OS_REG_RMW(ah, AR_CFG, AR_CFG_SWTB,0) #endif #elif AH_NEED_RX_DATA_SWAP #define ar9300_init_cfg_reg(ah) OS_REG_RMW(ah, AR_CFG, AR_CFG_SWRB,0) #else #define ar9300_init_cfg_reg(ah) OS_REG_RMW(ah, AR_CFG, AR_CFG_SWTD | AR_CFG_SWRD,0) #endif extern HAL_BOOL ar9300_rf_attach(struct ath_hal *, HAL_STATUS *); struct ath_hal; extern struct ath_hal_9300 * ar9300_new_state(u_int16_t devid, HAL_SOFTC sc, HAL_BUS_TAG st, HAL_BUS_HANDLE sh, uint16_t *eepromdata, HAL_OPS_CONFIG *ah_config, HAL_STATUS *status); extern struct ath_hal * ar9300_attach(u_int16_t devid, HAL_SOFTC sc, HAL_BUS_TAG st, HAL_BUS_HANDLE sh, uint16_t *eepromdata, HAL_OPS_CONFIG *ah_config, HAL_STATUS *status); extern void ar9300_detach(struct ath_hal *ah); extern void ar9300_read_revisions(struct ath_hal *ah); extern HAL_BOOL ar9300_chip_test(struct ath_hal *ah); extern HAL_BOOL ar9300_get_channel_edges(struct ath_hal *ah, u_int16_t flags, u_int16_t *low, u_int16_t *high); extern HAL_BOOL ar9300_fill_capability_info(struct ath_hal *ah); extern void ar9300_beacon_init(struct ath_hal *ah, u_int32_t next_beacon, u_int32_t beacon_period, u_int32_t beacon_period_fraction, HAL_OPMODE opmode); extern void ar9300_set_sta_beacon_timers(struct ath_hal *ah, const HAL_BEACON_STATE *); extern HAL_BOOL ar9300_is_interrupt_pending(struct ath_hal *ah); extern HAL_BOOL ar9300_get_pending_interrupts(struct ath_hal *ah, HAL_INT *, HAL_INT_TYPE, u_int8_t, HAL_BOOL); extern HAL_INT ar9300_get_interrupts(struct ath_hal *ah); extern HAL_INT ar9300_set_interrupts(struct ath_hal *ah, HAL_INT ints, HAL_BOOL); extern void ar9300_set_intr_mitigation_timer(struct ath_hal* ah, HAL_INT_MITIGATION reg, u_int32_t value); extern u_int32_t ar9300_get_intr_mitigation_timer(struct ath_hal* ah, HAL_INT_MITIGATION reg); extern u_int32_t ar9300_get_key_cache_size(struct ath_hal *); extern HAL_BOOL ar9300_is_key_cache_entry_valid(struct ath_hal *, u_int16_t entry); extern HAL_BOOL ar9300_reset_key_cache_entry(struct ath_hal *ah, u_int16_t entry); extern HAL_CHANNEL_INTERNAL * ar9300_check_chan(struct ath_hal *ah, const struct ieee80211_channel *chan); extern HAL_BOOL ar9300_set_key_cache_entry_mac(struct ath_hal *, u_int16_t entry, const u_int8_t *mac); extern HAL_BOOL ar9300_set_key_cache_entry(struct ath_hal *ah, u_int16_t entry, const HAL_KEYVAL *k, const u_int8_t *mac, int xor_key); extern HAL_BOOL ar9300_print_keycache(struct ath_hal *ah); #if ATH_SUPPORT_KEYPLUMB_WAR extern HAL_BOOL ar9300_check_key_cache_entry(struct ath_hal *ah, u_int16_t entry, const HAL_KEYVAL *k, int xorKey); #endif extern void ar9300_get_mac_address(struct ath_hal *ah, u_int8_t *mac); extern HAL_BOOL ar9300_set_mac_address(struct ath_hal *ah, const u_int8_t *); extern void ar9300_get_bss_id_mask(struct ath_hal *ah, u_int8_t *mac); extern HAL_BOOL ar9300_set_bss_id_mask(struct ath_hal *, const u_int8_t *); extern HAL_STATUS ar9300_select_ant_config(struct ath_hal *ah, u_int32_t cfg); #if 0 extern u_int32_t ar9300_ant_ctrl_common_get(struct ath_hal *ah, HAL_BOOL is_2ghz); #endif extern HAL_BOOL ar9300_ant_swcom_sel(struct ath_hal *ah, u_int8_t ops, u_int32_t *common_tbl1, u_int32_t *common_tbl2); extern HAL_BOOL ar9300_set_regulatory_domain(struct ath_hal *ah, u_int16_t reg_domain, HAL_STATUS *stats); extern u_int ar9300_get_wireless_modes(struct ath_hal *ah); extern void ar9300_enable_rf_kill(struct ath_hal *); extern HAL_BOOL ar9300_gpio_cfg_output(struct ath_hal *, u_int32_t gpio, HAL_GPIO_MUX_TYPE signalType); extern HAL_BOOL ar9300_gpio_cfg_output_led_off(struct ath_hal *, u_int32_t gpio, HAL_GPIO_MUX_TYPE signalType); extern HAL_BOOL ar9300_gpio_cfg_input(struct ath_hal *, u_int32_t gpio); extern HAL_BOOL ar9300_gpio_set(struct ath_hal *, u_int32_t gpio, u_int32_t val); extern u_int32_t ar9300_gpio_get(struct ath_hal *ah, u_int32_t gpio); extern u_int32_t ar9300_gpio_get_intr(struct ath_hal *ah); extern void ar9300_gpio_set_intr(struct ath_hal *ah, u_int, u_int32_t ilevel); extern u_int32_t ar9300_gpio_get_polarity(struct ath_hal *ah); extern void ar9300_gpio_set_polarity(struct ath_hal *ah, u_int32_t, u_int32_t); extern u_int32_t ar9300_gpio_get_mask(struct ath_hal *ah); extern int ar9300_gpio_set_mask(struct ath_hal *ah, u_int32_t mask, u_int32_t pol_map); extern void ar9300_set_led_state(struct ath_hal *ah, HAL_LED_STATE state); extern void ar9300_set_power_led_state(struct ath_hal *ah, u_int8_t enable); extern void ar9300_set_network_led_state(struct ath_hal *ah, u_int8_t enable); extern void ar9300_write_associd(struct ath_hal *ah, const u_int8_t *bssid, u_int16_t assoc_id); extern u_int32_t ar9300_ppm_get_rssi_dump(struct ath_hal *); extern u_int32_t ar9300_ppm_arm_trigger(struct ath_hal *); extern int ar9300_ppm_get_trigger(struct ath_hal *); extern u_int32_t ar9300_ppm_force(struct ath_hal *); extern void ar9300_ppm_un_force(struct ath_hal *); extern u_int32_t ar9300_ppm_get_force_state(struct ath_hal *); extern void ar9300_set_dcs_mode(struct ath_hal *ah, u_int32_t); extern u_int32_t ar9300_get_dcs_mode(struct ath_hal *ah); extern u_int32_t ar9300_get_tsf32(struct ath_hal *ah); extern u_int64_t ar9300_get_tsf64(struct ath_hal *ah); extern u_int32_t ar9300_get_tsf2_32(struct ath_hal *ah); extern void ar9300_set_tsf64(struct ath_hal *ah, u_int64_t tsf); extern void ar9300_reset_tsf(struct ath_hal *ah); extern void ar9300_set_basic_rate(struct ath_hal *ah, HAL_RATE_SET *pSet); extern u_int32_t ar9300_get_random_seed(struct ath_hal *ah); extern HAL_BOOL ar9300_detect_card_present(struct ath_hal *ah); extern void ar9300_update_mib_mac_stats(struct ath_hal *ah); extern void ar9300_get_mib_mac_stats(struct ath_hal *ah, HAL_MIB_STATS* stats); extern HAL_BOOL ar9300_is_japan_channel_spread_supported(struct ath_hal *ah); extern u_int32_t ar9300_get_cur_rssi(struct ath_hal *ah); extern u_int32_t ar9300_get_rssi_chain0(struct ath_hal *ah); extern u_int ar9300_get_def_antenna(struct ath_hal *ah); extern void ar9300_set_def_antenna(struct ath_hal *ah, u_int antenna); extern HAL_BOOL ar9300_set_antenna_switch(struct ath_hal *ah, HAL_ANT_SETTING settings, const struct ieee80211_channel *chan, u_int8_t *, u_int8_t *, u_int8_t *); extern HAL_BOOL ar9300_is_sleep_after_beacon_broken(struct ath_hal *ah); extern HAL_BOOL ar9300_set_slot_time(struct ath_hal *, u_int); extern HAL_BOOL ar9300_set_ack_timeout(struct ath_hal *, u_int); extern u_int ar9300_get_ack_timeout(struct ath_hal *); extern HAL_STATUS ar9300_set_quiet(struct ath_hal *ah, u_int32_t period, u_int32_t duration, u_int32_t next_start, HAL_QUIET_FLAG flag); extern void ar9300_set_pcu_config(struct ath_hal *); extern HAL_STATUS ar9300_get_capability(struct ath_hal *, HAL_CAPABILITY_TYPE, u_int32_t, u_int32_t *); extern HAL_BOOL ar9300_set_capability(struct ath_hal *, HAL_CAPABILITY_TYPE, u_int32_t, u_int32_t, HAL_STATUS *); extern HAL_BOOL ar9300_get_diag_state(struct ath_hal *ah, int request, const void *args, u_int32_t argsize, void **result, u_int32_t *resultsize); extern void ar9300_get_desc_info(struct ath_hal *ah, HAL_DESC_INFO *desc_info); extern uint32_t ar9300_get_11n_ext_busy(struct ath_hal *ah); extern void ar9300_set_11n_mac2040(struct ath_hal *ah, HAL_HT_MACMODE mode); extern HAL_HT_RXCLEAR ar9300_get_11n_rx_clear(struct ath_hal *ah); extern void ar9300_set_11n_rx_clear(struct ath_hal *ah, HAL_HT_RXCLEAR rxclear); extern HAL_BOOL ar9300_set_power_mode(struct ath_hal *ah, HAL_POWER_MODE mode, int set_chip); extern HAL_POWER_MODE ar9300_get_power_mode(struct ath_hal *ah); extern HAL_BOOL ar9300_set_power_mode_awake(struct ath_hal *ah, int set_chip); extern void ar9300_set_sm_power_mode(struct ath_hal *ah, HAL_SMPS_MODE mode); extern void ar9300_config_pci_power_save(struct ath_hal *ah, int restore, int power_off); extern void ar9300_force_tsf_sync(struct ath_hal *ah, const u_int8_t *bssid, u_int16_t assoc_id); #if ATH_WOW extern void ar9300_wow_apply_pattern(struct ath_hal *ah, u_int8_t *p_ath_pattern, u_int8_t *p_ath_mask, int32_t pattern_count, u_int32_t ath_pattern_len); //extern u_int32_t ar9300_wow_wake_up(struct ath_hal *ah,u_int8_t *chipPatternBytes); extern u_int32_t ar9300_wow_wake_up(struct ath_hal *ah, HAL_BOOL offloadEnable); extern bool ar9300_wow_enable(struct ath_hal *ah, u_int32_t pattern_enable, u_int32_t timeout_in_seconds, int clearbssid, HAL_BOOL offloadEnable); #if ATH_WOW_OFFLOAD /* ARP offload */ #define WOW_OFFLOAD_ARP_INFO_MAX 2 struct hal_wow_offload_arp_info { u_int32_t valid; u_int32_t id; u_int32_t Flags; union { u_int8_t u8[4]; u_int32_t u32; } RemoteIPv4Address; union { u_int8_t u8[4]; u_int32_t u32; } HostIPv4Address; union { u_int8_t u8[6]; u_int32_t u32[2]; } MacAddress; }; /* NS offload */ #define WOW_OFFLOAD_NS_INFO_MAX 2 struct hal_wow_offload_ns_info { u_int32_t valid; u_int32_t id; u_int32_t Flags; union { u_int8_t u8[16]; u_int32_t u32[4]; } RemoteIPv6Address; union { u_int8_t u8[16]; u_int32_t u32[4]; } SolicitedNodeIPv6Address; union { u_int8_t u8[6]; u_int32_t u32[2]; } MacAddress; union { u_int8_t u8[16]; u_int32_t u32[4]; } TargetIPv6Addresses[2]; }; extern void ar9300_wowoffload_prep(struct ath_hal *ah); extern void ar9300_wowoffload_post(struct ath_hal *ah); extern u_int32_t ar9300_wowoffload_download_rekey_data(struct ath_hal *ah, u_int32_t *data, u_int32_t size); extern void ar9300_wowoffload_retrieve_data(struct ath_hal *ah, void *buf, u_int32_t param); extern void ar9300_wowoffload_download_acer_magic(struct ath_hal *ah, HAL_BOOL valid, u_int8_t* datap, u_int32_t bytes); extern void ar9300_wowoffload_download_acer_swka(struct ath_hal *ah, u_int32_t id, HAL_BOOL valid, u_int32_t period, u_int32_t size, u_int32_t* datap); extern void ar9300_wowoffload_download_arp_info(struct ath_hal *ah, u_int32_t id, u_int32_t *data); extern void ar9300_wowoffload_download_ns_info(struct ath_hal *ah, u_int32_t id, u_int32_t *data); #endif /* ATH_WOW_OFFLOAD */ #endif extern HAL_BOOL ar9300_reset(struct ath_hal *ah, HAL_OPMODE opmode, struct ieee80211_channel *chan, HAL_HT_MACMODE macmode, u_int8_t txchainmask, u_int8_t rxchainmask, HAL_HT_EXTPROTSPACING extprotspacing, HAL_BOOL b_channel_change, HAL_STATUS *status, int is_scan); extern HAL_BOOL ar9300_lean_channel_change(struct ath_hal *ah, HAL_OPMODE opmode, struct ieee80211_channel *chan, HAL_HT_MACMODE macmode, u_int8_t txchainmask, u_int8_t rxchainmask); extern HAL_BOOL ar9300_set_reset_reg(struct ath_hal *ah, u_int32_t type); extern void ar9300_init_pll(struct ath_hal *ah, struct ieee80211_channel *chan); extern void ar9300_green_ap_ps_on_off( struct ath_hal *ah, u_int16_t rxMask); extern u_int16_t ar9300_is_single_ant_power_save_possible(struct ath_hal *ah); extern void ar9300_set_operating_mode(struct ath_hal *ah, int opmode); extern HAL_BOOL ar9300_phy_disable(struct ath_hal *ah); extern HAL_BOOL ar9300_disable(struct ath_hal *ah); extern HAL_BOOL ar9300_chip_reset(struct ath_hal *ah, struct ieee80211_channel *); extern HAL_BOOL ar9300_calibration(struct ath_hal *ah, struct ieee80211_channel *chan, u_int8_t rxchainmask, HAL_BOOL longcal, HAL_BOOL *isIQdone, int is_scan, u_int32_t *sched_cals); extern void ar9300_reset_cal_valid(struct ath_hal *ah, const struct ieee80211_channel *chan, HAL_BOOL *isIQdone, u_int32_t cal_type); extern void ar9300_iq_cal_collect(struct ath_hal *ah, u_int8_t num_chains); extern void ar9300_iq_calibration(struct ath_hal *ah, u_int8_t num_chains); extern void ar9300_temp_comp_cal_collect(struct ath_hal *ah); extern void ar9300_temp_comp_calibration(struct ath_hal *ah, u_int8_t num_chains); extern int16_t ar9300_get_min_cca_pwr(struct ath_hal *ah); extern void ar9300_upload_noise_floor(struct ath_hal *ah, int is2G, int16_t nfarray[]); extern HAL_BOOL ar9300_set_tx_power_limit(struct ath_hal *ah, u_int32_t limit, u_int16_t extra_txpow, u_int16_t tpc_in_db); extern void ar9300_chain_noise_floor(struct ath_hal *ah, int16_t *nf_buf, struct ieee80211_channel *chan, int is_scan); extern int16_t ar9300_get_nf_from_reg(struct ath_hal *ah, struct ieee80211_channel *chan, int wait_time); extern int ar9300_get_rx_nf_offset(struct ath_hal *ah, struct ieee80211_channel *chan, int8_t *nf_pwr, int8_t *nf_cal); extern HAL_BOOL ar9300_load_nf(struct ath_hal *ah, int16_t nf[]); extern HAL_RFGAIN ar9300_get_rfgain(struct ath_hal *ah); extern const HAL_RATE_TABLE *ar9300_get_rate_table(struct ath_hal *, u_int mode); extern int16_t ar9300_get_rate_txpower(struct ath_hal *ah, u_int mode, u_int8_t rate_index, u_int8_t chainmask, u_int8_t mimo_mode); extern void ar9300_init_rate_txpower(struct ath_hal *ah, u_int mode, const struct ieee80211_channel *chan, u_int8_t powerPerRate[], u_int8_t chainmask); extern void ar9300_adjust_reg_txpower_cdd(struct ath_hal *ah, u_int8_t powerPerRate[]); extern HAL_STATUS ath_hal_get_rate_power_limit_from_eeprom(struct ath_hal *ah, u_int16_t freq, int8_t *max_rate_power, int8_t *min_rate_power); extern void ar9300_reset_tx_status_ring(struct ath_hal *ah); extern void ar9300_enable_mib_counters(struct ath_hal *); extern void ar9300_disable_mib_counters(struct ath_hal *); extern void ar9300_ani_attach(struct ath_hal *); extern void ar9300_ani_detach(struct ath_hal *); extern struct ar9300_ani_state *ar9300_ani_get_current_state(struct ath_hal *); extern HAL_ANI_STATS *ar9300_ani_get_current_stats(struct ath_hal *); extern HAL_BOOL ar9300_ani_control(struct ath_hal *, HAL_ANI_CMD cmd, int param); struct ath_rx_status; extern void ar9300_process_mib_intr(struct ath_hal *, const HAL_NODE_STATS *); extern void ar9300_ani_ar_poll(struct ath_hal *, const HAL_NODE_STATS *, const struct ieee80211_channel *, HAL_ANISTATS *); extern void ar9300_ani_reset(struct ath_hal *, HAL_BOOL is_scanning); extern void ar9300_ani_init_defaults(struct ath_hal *ah, HAL_HT_MACMODE macmode); extern void ar9300_enable_tpc(struct ath_hal *); extern HAL_BOOL ar9300_rf_gain_cap_apply(struct ath_hal *ah, int is2GHz); extern void ar9300_rx_gain_table_apply(struct ath_hal *ah); extern void ar9300_tx_gain_table_apply(struct ath_hal *ah); extern void ar9300_mat_enable(struct ath_hal *ah, int enable); extern void ar9300_dump_keycache(struct ath_hal *ah, int n, u_int32_t *entry); extern HAL_BOOL ar9300_ant_ctrl_set_lna_div_use_bt_ant(struct ath_hal * ah, HAL_BOOL enable, const struct ieee80211_channel * chan); /* BB Panic Watchdog declarations */ #define HAL_BB_PANIC_WD_TMO 25 /* in ms, 0 to disable */ #define HAL_BB_PANIC_WD_TMO_HORNET 85 extern void ar9300_config_bb_panic_watchdog(struct ath_hal *); extern void ar9300_handle_bb_panic(struct ath_hal *); extern int ar9300_get_bb_panic_info(struct ath_hal *ah, struct hal_bb_panic_info *bb_panic); extern HAL_BOOL ar9300_handle_radar_bb_panic(struct ath_hal *ah); extern void ar9300_set_hal_reset_reason(struct ath_hal *ah, u_int8_t resetreason); /* DFS declarations */ extern void ar9300_check_dfs(struct ath_hal *ah, struct ieee80211_channel *chan); extern void ar9300_dfs_found(struct ath_hal *ah, struct ieee80211_channel *chan, u_int64_t nolTime); extern void ar9300_enable_dfs(struct ath_hal *ah, HAL_PHYERR_PARAM *pe); extern void ar9300_get_dfs_thresh(struct ath_hal *ah, HAL_PHYERR_PARAM *pe); extern HAL_BOOL ar9300_radar_wait(struct ath_hal *ah, struct ieee80211_channel *chan); extern struct dfs_pulse * ar9300_get_dfs_radars(struct ath_hal *ah, u_int32_t dfsdomain, int *numradars, struct dfs_bin5pulse **bin5pulses, int *numb5radars, HAL_PHYERR_PARAM *pe); extern HAL_BOOL ar9300_get_default_dfs_thresh(struct ath_hal *ah, HAL_PHYERR_PARAM *pe); extern void ar9300_adjust_difs(struct ath_hal *ah, u_int32_t val); extern u_int32_t ar9300_dfs_config_fft(struct ath_hal *ah, HAL_BOOL is_enable); extern void ar9300_cac_tx_quiet(struct ath_hal *ah, HAL_BOOL enable); extern void ar9300_dfs_cac_war(struct ath_hal *ah, u_int32_t start); extern struct ieee80211_channel * ar9300_get_extension_channel(struct ath_hal *ah); extern HAL_BOOL ar9300_is_fast_clock_enabled(struct ath_hal *ah); extern void ar9300_mark_phy_inactive(struct ath_hal *ah); /* Spectral scan declarations */ extern void ar9300_configure_spectral_scan(struct ath_hal *ah, HAL_SPECTRAL_PARAM *ss); extern void ar9300_set_cca_threshold(struct ath_hal *ah, u_int8_t thresh62); extern void ar9300_get_spectral_params(struct ath_hal *ah, HAL_SPECTRAL_PARAM *ss); extern HAL_BOOL ar9300_is_spectral_active(struct ath_hal *ah); extern HAL_BOOL ar9300_is_spectral_enabled(struct ath_hal *ah); extern void ar9300_start_spectral_scan(struct ath_hal *ah); extern void ar9300_stop_spectral_scan(struct ath_hal *ah); extern u_int32_t ar9300_get_spectral_config(struct ath_hal *ah); extern void ar9300_restore_spectral_config(struct ath_hal *ah, u_int32_t restoreval); int16_t ar9300_get_ctl_chan_nf(struct ath_hal *ah); int16_t ar9300_get_ext_chan_nf(struct ath_hal *ah); /* End spectral scan declarations */ /* Raw ADC capture functions */ extern void ar9300_enable_test_addac_mode(struct ath_hal *ah); extern void ar9300_disable_test_addac_mode(struct ath_hal *ah); extern void ar9300_begin_adc_capture(struct ath_hal *ah, int auto_agc_gain); extern HAL_STATUS ar9300_retrieve_capture_data(struct ath_hal *ah, u_int16_t chain_mask, int disable_dc_filter, void *sample_buf, u_int32_t *max_samples); extern HAL_STATUS ar9300_calc_adc_ref_powers(struct ath_hal *ah, int freq_mhz, int16_t *sample_min, int16_t *sample_max, int32_t *chain_ref_pwr, int num_chain_ref_pwr); extern HAL_STATUS ar9300_get_min_agc_gain(struct ath_hal *ah, int freq_mhz, int32_t *chain_gain, int num_chain_gain); extern HAL_BOOL ar9300_reset_11n(struct ath_hal *ah, HAL_OPMODE opmode, struct ieee80211_channel *chan, HAL_BOOL b_channel_change, HAL_STATUS *status); extern void ar9300_set_coverage_class(struct ath_hal *ah, u_int8_t coverageclass, int now); extern void ar9300_get_channel_centers(struct ath_hal *ah, const struct ieee80211_channel *chan, CHAN_CENTERS *centers); extern u_int16_t ar9300_get_ctl_center(struct ath_hal *ah, const struct ieee80211_channel *chan); extern u_int16_t ar9300_get_ext_center(struct ath_hal *ah, const struct ieee80211_channel *chan); extern u_int32_t ar9300_get_mib_cycle_counts_pct(struct ath_hal *, u_int32_t*, u_int32_t*, u_int32_t*); extern void ar9300_dma_reg_dump(struct ath_hal *); extern HAL_BOOL ar9300_set_11n_rx_rifs(struct ath_hal *ah, HAL_BOOL enable); extern HAL_BOOL ar9300_set_rifs_delay(struct ath_hal *ah, HAL_BOOL enable); extern HAL_BOOL ar9300_set_smart_antenna(struct ath_hal *ah, HAL_BOOL enable); extern HAL_BOOL ar9300_detect_bb_hang(struct ath_hal *ah); extern HAL_BOOL ar9300_detect_mac_hang(struct ath_hal *ah); #ifdef ATH_BT_COEX extern void ar9300_set_bt_coex_info(struct ath_hal *ah, HAL_BT_COEX_INFO *btinfo); extern void ar9300_bt_coex_config(struct ath_hal *ah, HAL_BT_COEX_CONFIG *btconf); extern void ar9300_bt_coex_set_qcu_thresh(struct ath_hal *ah, int qnum); extern void ar9300_bt_coex_set_weights(struct ath_hal *ah, u_int32_t stomp_type); extern void ar9300_bt_coex_setup_bmiss_thresh(struct ath_hal *ah, u_int32_t thresh); extern void ar9300_bt_coex_set_parameter(struct ath_hal *ah, u_int32_t type, u_int32_t value); extern void ar9300_bt_coex_disable(struct ath_hal *ah); extern int ar9300_bt_coex_enable(struct ath_hal *ah); extern void ar9300_init_bt_coex(struct ath_hal *ah); extern u_int32_t ar9300_get_bt_active_gpio(struct ath_hal *ah, u_int32_t reg); extern u_int32_t ar9300_get_wlan_active_gpio(struct ath_hal *ah, u_int32_t reg,u_int32_t bOn); #endif extern int ar9300_alloc_generic_timer(struct ath_hal *ah, HAL_GEN_TIMER_DOMAIN tsf); extern void ar9300_free_generic_timer(struct ath_hal *ah, int index); extern void ar9300_start_generic_timer(struct ath_hal *ah, int index, u_int32_t timer_next, u_int32_t timer_period); extern void ar9300_stop_generic_timer(struct ath_hal *ah, int index); extern void ar9300_get_gen_timer_interrupts(struct ath_hal *ah, u_int32_t *trigger, u_int32_t *thresh); extern void ar9300_start_tsf2(struct ath_hal *ah); extern void ar9300_chk_rssi_update_tx_pwr(struct ath_hal *ah, int rssi); extern HAL_BOOL ar9300_is_skip_paprd_by_greentx(struct ath_hal *ah); extern void ar9300_control_signals_for_green_tx_mode(struct ath_hal *ah); extern void ar9300_hwgreentx_set_pal_spare(struct ath_hal *ah, int value); extern HAL_BOOL ar9300_is_ani_noise_spur(struct ath_hal *ah); extern void ar9300_reset_hw_beacon_proc_crc(struct ath_hal *ah); extern int32_t ar9300_get_hw_beacon_rssi(struct ath_hal *ah); extern void ar9300_set_hw_beacon_rssi_threshold(struct ath_hal *ah, u_int32_t rssi_threshold); extern void ar9300_reset_hw_beacon_rssi(struct ath_hal *ah); extern void ar9300_set_hw_beacon_proc(struct ath_hal *ah, HAL_BOOL on); extern void ar9300_get_vow_stats(struct ath_hal *ah, HAL_VOWSTATS *p_stats, u_int8_t); extern int ar9300_get_spur_info(struct ath_hal * ah, int *enable, int len, u_int16_t *freq); extern int ar9300_set_spur_info(struct ath_hal * ah, int enable, int len, u_int16_t *freq); extern void ar9300_wow_set_gpio_reset_low(struct ath_hal * ah); extern HAL_BOOL ar9300_get_mib_cycle_counts(struct ath_hal *, HAL_SURVEY_SAMPLE *); extern void ar9300_clear_mib_counters(struct ath_hal *ah); /* EEPROM interface functions */ /* Common Interface functions */ extern HAL_STATUS ar9300_eeprom_attach(struct ath_hal *); extern u_int32_t ar9300_eeprom_get(struct ath_hal_9300 *ahp, EEPROM_PARAM param); extern u_int32_t ar9300_ini_fixup(struct ath_hal *ah, ar9300_eeprom_t *p_eep_data, u_int32_t reg, u_int32_t val); extern HAL_STATUS ar9300_eeprom_set_transmit_power(struct ath_hal *ah, ar9300_eeprom_t *p_eep_data, const struct ieee80211_channel *chan, u_int16_t cfg_ctl, u_int16_t twice_antenna_reduction, u_int16_t twice_max_regulatory_power, u_int16_t power_limit); extern void ar9300_eeprom_set_addac(struct ath_hal *, struct ieee80211_channel *); extern HAL_BOOL ar9300_eeprom_set_param(struct ath_hal *ah, EEPROM_PARAM param, u_int32_t value); extern HAL_BOOL ar9300_eeprom_set_board_values(struct ath_hal *, const struct ieee80211_channel *); extern HAL_BOOL ar9300_eeprom_read_word(struct ath_hal *, u_int off, u_int16_t *data); extern HAL_BOOL ar9300_eeprom_read(struct ath_hal *ah, long address, u_int8_t *buffer, int many); extern HAL_BOOL ar9300_otp_read(struct ath_hal *ah, u_int off, u_int32_t *data, HAL_BOOL is_wifi); extern HAL_BOOL ar9300_flash_read(struct ath_hal *, u_int off, u_int16_t *data); extern HAL_BOOL ar9300_flash_write(struct ath_hal *, u_int off, u_int16_t data); extern u_int ar9300_eeprom_dump_support(struct ath_hal *ah, void **pp_e); extern u_int8_t ar9300_eeprom_get_num_ant_config(struct ath_hal_9300 *ahp, HAL_FREQ_BAND freq_band); extern HAL_STATUS ar9300_eeprom_get_ant_cfg(struct ath_hal_9300 *ahp, const struct ieee80211_channel *chan, u_int8_t index, u_int16_t *config); extern u_int8_t* ar9300_eeprom_get_cust_data(struct ath_hal_9300 *ahp); extern u_int8_t *ar9300_eeprom_get_spur_chans_ptr(struct ath_hal *ah, HAL_BOOL is_2ghz); extern HAL_BOOL ar9300_interference_is_present(struct ath_hal *ah); extern HAL_BOOL ar9300_tuning_caps_apply(struct ath_hal *ah); extern void ar9300_disp_tpc_tables(struct ath_hal *ah); extern u_int8_t *ar9300_get_tpc_tables(struct ath_hal *ah); extern u_int8_t ar9300_eeprom_set_tx_gain_cap(struct ath_hal *ah, int *tx_gain_max); extern u_int8_t ar9300_eeprom_tx_gain_table_index_max_apply(struct ath_hal *ah, u_int16_t channel); /* Common EEPROM Help function */ extern void ar9300_set_immunity(struct ath_hal *ah, HAL_BOOL enable); extern void ar9300_get_hw_hangs(struct ath_hal *ah, hal_hw_hangs_t *hangs); extern u_int ar9300_mac_to_clks(struct ath_hal *ah, u_int clks); /* tx_bf interface */ #define ar9300_init_txbf(ah) #define ar9300_set_11n_txbf_sounding(ah, ds, series, cec, opt) #define ar9300_set_11n_txbf_cal(ah, ds, cal_pos, code_rate, cec, opt) #define ar9300_txbf_save_cv_from_compress( \ ah, key_idx, mimo_control, compress_rpt) \ false #define ar9300_txbf_save_cv_from_non_compress( \ ah, key_idx, mimo_control, non_compress_rpt) \ false #define ar9300_txbf_rc_update( \ ah, rx_status, local_h, csi_frame, ness_a, ness_b, bw) \ false #define ar9300_fill_csi_frame( \ ah, rx_status, bandwidth, local_h, csi_frame_body) \ 0 #define ar9300_fill_txbf_capabilities(ah) #define ar9300_get_txbf_capabilities(ah) NULL #define ar9300_txbf_set_key( \ ah, entry, rx_staggered_sounding, channel_estimation_cap, mmss) #define ar9300_read_key_cache_mac(ah, entry, mac) false #define ar9300_txbf_get_cv_cache_nr(ah, key_idx, nr) #define ar9300_set_selfgenrate_limit(ah, ts_ratecode) #define ar9300_reset_lowest_txrate(ah) #define ar9300_txbf_set_basic_set(ah) extern void ar9300_crdc_rx_notify(struct ath_hal *ah, struct ath_rx_status *rxs); extern void ar9300_chain_rssi_diff_compensation(struct ath_hal *ah); #if ATH_SUPPORT_MCI extern void ar9300_mci_bt_coex_set_weights(struct ath_hal *ah, u_int32_t stomp_type); extern void ar9300_mci_bt_coex_disable(struct ath_hal *ah); extern int ar9300_mci_bt_coex_enable(struct ath_hal *ah); extern void ar9300_mci_setup (struct ath_hal *ah, u_int32_t gpm_addr, void *gpm_buf, u_int16_t len, u_int32_t sched_addr); extern void ar9300_mci_remote_reset(struct ath_hal *ah, HAL_BOOL wait_done); extern void ar9300_mci_send_lna_transfer(struct ath_hal *ah, HAL_BOOL wait_done); extern void ar9300_mci_send_sys_waking(struct ath_hal *ah, HAL_BOOL wait_done); extern HAL_BOOL ar9300_mci_send_message (struct ath_hal *ah, u_int8_t header, u_int32_t flag, u_int32_t *payload, u_int8_t len, HAL_BOOL wait_done, HAL_BOOL check_bt); extern u_int32_t ar9300_mci_get_interrupt (struct ath_hal *ah, u_int32_t *mci_int, u_int32_t *mci_int_rx_msg); extern u_int32_t ar9300_mci_state (struct ath_hal *ah, u_int32_t state_type, u_int32_t *p_data); extern void ar9300_mci_reset (struct ath_hal *ah, HAL_BOOL en_int, HAL_BOOL is_2g, HAL_BOOL is_full_sleep); extern void ar9300_mci_send_coex_halt_bt_gpm(struct ath_hal *ah, HAL_BOOL halt, HAL_BOOL wait_done); extern void ar9300_mci_mute_bt(struct ath_hal *ah); extern u_int32_t ar9300_mci_wait_for_gpm(struct ath_hal *ah, u_int8_t gpm_type, u_int8_t gpm_opcode, int32_t time_out); extern void ar9300_mci_enable_interrupt(struct ath_hal *ah); extern void ar9300_mci_disable_interrupt(struct ath_hal *ah); extern void ar9300_mci_detach (struct ath_hal *ah); extern u_int32_t ar9300_mci_check_int (struct ath_hal *ah, u_int32_t ints); extern void ar9300_mci_sync_bt_state (struct ath_hal *ah); extern void ar9300_mci_2g5g_changed(struct ath_hal *ah, HAL_BOOL is_2g); extern void ar9300_mci_2g5g_switch(struct ath_hal *ah, HAL_BOOL wait_done); #if ATH_SUPPORT_AIC extern u_int32_t ar9300_aic_calibration (struct ath_hal *ah); extern u_int32_t ar9300_aic_start_normal (struct ath_hal *ah); #endif #endif extern HAL_STATUS ar9300_set_proxy_sta(struct ath_hal *ah, HAL_BOOL enable); extern HAL_BOOL ar9300_regulatory_domain_override( struct ath_hal *ah, u_int16_t regdmn); #if ATH_ANT_DIV_COMB extern void ar9300_ant_div_comb_get_config(struct ath_hal *ah, HAL_ANT_COMB_CONFIG* div_comb_conf); extern void ar9300_ant_div_comb_set_config(struct ath_hal *ah, HAL_ANT_COMB_CONFIG* div_comb_conf); #endif /* ATH_ANT_DIV_COMB */ extern void ar9300_disable_phy_restart(struct ath_hal *ah, int disable_phy_restart); extern void ar9300_enable_keysearch_always(struct ath_hal *ah, int enable); extern HAL_BOOL ar9300ForceVCS( struct ath_hal *ah); extern HAL_BOOL ar9300SetDfs3StreamFix(struct ath_hal *ah, u_int32_t val); extern HAL_BOOL ar9300Get3StreamSignature( struct ath_hal *ah); #ifdef ATH_TX99_DIAG #ifndef ATH_SUPPORT_HTC extern void ar9300_tx99_channel_pwr_update(struct ath_hal *ah, struct ieee80211_channel *c, u_int32_t txpower); extern void ar9300_tx99_chainmsk_setup(struct ath_hal *ah, int tx_chainmask); extern void ar9300_tx99_set_single_carrier(struct ath_hal *ah, int tx_chain_mask, int chtype); extern void ar9300_tx99_start(struct ath_hal *ah, u_int8_t *data); extern void ar9300_tx99_stop(struct ath_hal *ah); #endif /* ATH_SUPPORT_HTC */ #endif /* ATH_TX99_DIAG */ extern HAL_BOOL ar9300_set_ctl_pwr(struct ath_hal *ah, u_int8_t *ctl_array); extern void ar9300_set_txchainmaskopt(struct ath_hal *ah, u_int8_t mask); enum { AR9300_COEFF_TX_TYPE = 0, AR9300_COEFF_RX_TYPE }; #endif /* _ATH_AR9300_H_ */ Index: head/sys/dev/ath/ath_hal/ah.h =================================================================== --- head/sys/dev/ath/ath_hal/ah.h (revision 334196) +++ head/sys/dev/ath/ath_hal/ah.h (revision 334197) @@ -1,1693 +1,1699 @@ /*- * SPDX-License-Identifier: ISC * * Copyright (c) 2002-2009 Sam Leffler, Errno Consulting * Copyright (c) 2002-2008 Atheros Communications, Inc. * * Permission to use, copy, modify, and/or distribute this software for any * purpose with or without fee is hereby granted, provided that the above * copyright notice and this permission notice appear in all copies. * * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE. * * $FreeBSD$ */ #ifndef _ATH_AH_H_ #define _ATH_AH_H_ /* * Atheros Hardware Access Layer * * Clients of the HAL call ath_hal_attach to obtain a reference to an ath_hal * structure for use with the device. Hardware-related operations that * follow must call back into the HAL through interface, supplying the * reference as the first parameter. */ #include "ah_osdep.h" /* * The maximum number of TX/RX chains supported. * This is intended to be used by various statistics gathering operations * (NF, RSSI, EVM). */ #define AH_MAX_CHAINS 3 #define AH_MIMO_MAX_EVM_PILOTS 6 /* * __ahdecl is analogous to _cdecl; it defines the calling * convention used within the HAL. For most systems this * can just default to be empty and the compiler will (should) * use _cdecl. For systems where _cdecl is not compatible this * must be defined. See linux/ah_osdep.h for an example. */ #ifndef __ahdecl #define __ahdecl #endif /* * Status codes that may be returned by the HAL. Note that * interfaces that return a status code set it only when an * error occurs--i.e. you cannot check it for success. */ typedef enum { HAL_OK = 0, /* No error */ HAL_ENXIO = 1, /* No hardware present */ HAL_ENOMEM = 2, /* Memory allocation failed */ HAL_EIO = 3, /* Hardware didn't respond as expected */ HAL_EEMAGIC = 4, /* EEPROM magic number invalid */ HAL_EEVERSION = 5, /* EEPROM version invalid */ HAL_EELOCKED = 6, /* EEPROM unreadable */ HAL_EEBADSUM = 7, /* EEPROM checksum invalid */ HAL_EEREAD = 8, /* EEPROM read problem */ HAL_EEBADMAC = 9, /* EEPROM mac address invalid */ HAL_EESIZE = 10, /* EEPROM size not supported */ HAL_EEWRITE = 11, /* Attempt to change write-locked EEPROM */ HAL_EINVAL = 12, /* Invalid parameter to function */ HAL_ENOTSUPP = 13, /* Hardware revision not supported */ HAL_ESELFTEST = 14, /* Hardware self-test failed */ HAL_EINPROGRESS = 15, /* Operation incomplete */ HAL_EEBADREG = 16, /* EEPROM invalid regulatory contents */ HAL_EEBADCC = 17, /* EEPROM invalid country code */ HAL_INV_PMODE = 18, /* Couldn't bring out of sleep state */ } HAL_STATUS; typedef enum { AH_FALSE = 0, /* NB: lots of code assumes false is zero */ AH_TRUE = 1, } HAL_BOOL; typedef enum { HAL_CAP_REG_DMN = 0, /* current regulatory domain */ HAL_CAP_CIPHER = 1, /* hardware supports cipher */ HAL_CAP_TKIP_MIC = 2, /* handle TKIP MIC in hardware */ HAL_CAP_TKIP_SPLIT = 3, /* hardware TKIP uses split keys */ HAL_CAP_PHYCOUNTERS = 4, /* hardware PHY error counters */ HAL_CAP_DIVERSITY = 5, /* hardware supports fast diversity */ HAL_CAP_KEYCACHE_SIZE = 6, /* number of entries in key cache */ HAL_CAP_NUM_TXQUEUES = 7, /* number of hardware xmit queues */ HAL_CAP_VEOL = 9, /* hardware supports virtual EOL */ HAL_CAP_PSPOLL = 10, /* hardware has working PS-Poll support */ HAL_CAP_DIAG = 11, /* hardware diagnostic support */ HAL_CAP_COMPRESSION = 12, /* hardware supports compression */ HAL_CAP_BURST = 13, /* hardware supports packet bursting */ HAL_CAP_FASTFRAME = 14, /* hardware supoprts fast frames */ HAL_CAP_TXPOW = 15, /* global tx power limit */ HAL_CAP_TPC = 16, /* per-packet tx power control */ HAL_CAP_PHYDIAG = 17, /* hardware phy error diagnostic */ HAL_CAP_BSSIDMASK = 18, /* hardware supports bssid mask */ HAL_CAP_MCAST_KEYSRCH = 19, /* hardware has multicast key search */ HAL_CAP_TSF_ADJUST = 20, /* hardware has beacon tsf adjust */ /* 21 was HAL_CAP_XR */ HAL_CAP_WME_TKIPMIC = 22, /* hardware can support TKIP MIC when WMM is turned on */ /* 23 was HAL_CAP_CHAN_HALFRATE */ /* 24 was HAL_CAP_CHAN_QUARTERRATE */ HAL_CAP_RFSILENT = 25, /* hardware has rfsilent support */ HAL_CAP_TPC_ACK = 26, /* ack txpower with per-packet tpc */ HAL_CAP_TPC_CTS = 27, /* cts txpower with per-packet tpc */ HAL_CAP_11D = 28, /* 11d beacon support for changing cc */ HAL_CAP_PCIE_PS = 29, HAL_CAP_HT = 30, /* hardware can support HT */ HAL_CAP_GTXTO = 31, /* hardware supports global tx timeout */ HAL_CAP_FAST_CC = 32, /* hardware supports fast channel change */ HAL_CAP_TX_CHAINMASK = 33, /* mask of TX chains supported */ HAL_CAP_RX_CHAINMASK = 34, /* mask of RX chains supported */ HAL_CAP_NUM_GPIO_PINS = 36, /* number of GPIO pins */ HAL_CAP_CST = 38, /* hardware supports carrier sense timeout */ HAL_CAP_RIFS_RX = 39, HAL_CAP_RIFS_TX = 40, HAL_CAP_FORCE_PPM = 41, HAL_CAP_RTS_AGGR_LIMIT = 42, /* aggregation limit with RTS */ HAL_CAP_4ADDR_AGGR = 43, /* hardware is capable of 4addr aggregation */ HAL_CAP_DFS_DMN = 44, /* current DFS domain */ HAL_CAP_EXT_CHAN_DFS = 45, /* DFS support for extension channel */ HAL_CAP_COMBINED_RADAR_RSSI = 46, /* Is combined RSSI for radar accurate */ HAL_CAP_AUTO_SLEEP = 48, /* hardware can go to network sleep automatically after waking up to receive TIM */ HAL_CAP_MBSSID_AGGR_SUPPORT = 49, /* Support for mBSSID Aggregation */ HAL_CAP_SPLIT_4KB_TRANS = 50, /* hardware supports descriptors straddling a 4k page boundary */ HAL_CAP_REG_FLAG = 51, /* Regulatory domain flags */ HAL_CAP_BB_RIFS_HANG = 52, HAL_CAP_RIFS_RX_ENABLED = 53, HAL_CAP_BB_DFS_HANG = 54, HAL_CAP_RX_STBC = 58, HAL_CAP_TX_STBC = 59, HAL_CAP_BT_COEX = 60, /* hardware is capable of bluetooth coexistence */ HAL_CAP_DYNAMIC_SMPS = 61, /* Dynamic MIMO Power Save hardware support */ HAL_CAP_DS = 67, /* 2 stream */ HAL_CAP_BB_RX_CLEAR_STUCK_HANG = 68, HAL_CAP_MAC_HANG = 69, /* can MAC hang */ HAL_CAP_MFP = 70, /* Management Frame Protection in hardware */ HAL_CAP_TS = 72, /* 3 stream */ HAL_CAP_ENHANCED_DMA_SUPPORT = 75, /* DMA FIFO support */ HAL_CAP_NUM_TXMAPS = 76, /* Number of buffers in a transmit descriptor */ HAL_CAP_TXDESCLEN = 77, /* Length of transmit descriptor */ HAL_CAP_TXSTATUSLEN = 78, /* Length of transmit status descriptor */ HAL_CAP_RXSTATUSLEN = 79, /* Length of transmit status descriptor */ HAL_CAP_RXFIFODEPTH = 80, /* Receive hardware FIFO depth */ HAL_CAP_RXBUFSIZE = 81, /* Receive Buffer Length */ HAL_CAP_NUM_MR_RETRIES = 82, /* limit on multirate retries */ HAL_CAP_OL_PWRCTRL = 84, /* Open loop TX power control */ HAL_CAP_SPECTRAL_SCAN = 90, /* Hardware supports spectral scan */ HAL_CAP_BB_PANIC_WATCHDOG = 92, HAL_CAP_HT20_SGI = 96, /* hardware supports HT20 short GI */ HAL_CAP_LDPC = 99, HAL_CAP_RXTSTAMP_PREC = 100, /* rx desc tstamp precision (bits) */ HAL_CAP_ANT_DIV_COMB = 105, /* Enable antenna diversity/combining */ HAL_CAP_PHYRESTART_CLR_WAR = 106, /* in some cases, clear phy restart to fix bb hang */ HAL_CAP_ENTERPRISE_MODE = 107, /* Enterprise mode features */ HAL_CAP_LDPCWAR = 108, HAL_CAP_CHANNEL_SWITCH_TIME_USEC = 109, /* Channel change time, usec */ HAL_CAP_ENABLE_APM = 110, /* APM enabled */ HAL_CAP_PCIE_LCR_EXTSYNC_EN = 111, HAL_CAP_PCIE_LCR_OFFSET = 112, HAL_CAP_ENHANCED_DFS_SUPPORT = 117, /* hardware supports enhanced DFS */ HAL_CAP_MCI = 118, HAL_CAP_SMARTANTENNA = 119, HAL_CAP_TRAFFIC_FAST_RECOVER = 120, HAL_CAP_TX_DIVERSITY = 121, HAL_CAP_CRDC = 122, /* The following are private to the FreeBSD HAL (224 onward) */ HAL_CAP_INTMIT = 229, /* interference mitigation */ HAL_CAP_RXORN_FATAL = 230, /* HAL_INT_RXORN treated as fatal */ HAL_CAP_BB_HANG = 235, /* can baseband hang */ HAL_CAP_INTRMASK = 237, /* bitmask of supported interrupts */ HAL_CAP_BSSIDMATCH = 238, /* hardware has disable bssid match */ HAL_CAP_STREAMS = 239, /* how many 802.11n spatial streams are available */ HAL_CAP_RXDESC_SELFLINK = 242, /* support a self-linked tail RX descriptor */ HAL_CAP_BB_READ_WAR = 244, /* baseband read WAR */ HAL_CAP_SERIALISE_WAR = 245, /* serialise register access on PCI */ HAL_CAP_ENFORCE_TXOP = 246, /* Enforce TXOP if supported */ HAL_CAP_RX_LNA_MIXING = 247, /* RX hardware uses LNA mixing */ HAL_CAP_DO_MYBEACON = 248, /* Supports HAL_RX_FILTER_MYBEACON */ HAL_CAP_TOA_LOCATIONING = 249, /* time of flight / arrival locationing */ HAL_CAP_TXTSTAMP_PREC = 250, /* tx desc tstamp precision (bits) */ } HAL_CAPABILITY_TYPE; /* * "States" for setting the LED. These correspond to * the possible 802.11 operational states and there may * be a many-to-one mapping between these states and the * actual hardware state for the LED's (i.e. the hardware * may have fewer states). */ typedef enum { HAL_LED_INIT = 0, HAL_LED_SCAN = 1, HAL_LED_AUTH = 2, HAL_LED_ASSOC = 3, HAL_LED_RUN = 4 } HAL_LED_STATE; /* * Transmit queue types/numbers. These are used to tag * each transmit queue in the hardware and to identify a set * of transmit queues for operations such as start/stop dma. */ typedef enum { HAL_TX_QUEUE_INACTIVE = 0, /* queue is inactive/unused */ HAL_TX_QUEUE_DATA = 1, /* data xmit q's */ HAL_TX_QUEUE_BEACON = 2, /* beacon xmit q */ HAL_TX_QUEUE_CAB = 3, /* "crap after beacon" xmit q */ HAL_TX_QUEUE_UAPSD = 4, /* u-apsd power save xmit q */ HAL_TX_QUEUE_PSPOLL = 5, /* power save poll xmit q */ HAL_TX_QUEUE_CFEND = 6, HAL_TX_QUEUE_PAPRD = 7, } HAL_TX_QUEUE; #define HAL_NUM_TX_QUEUES 10 /* max possible # of queues */ /* * Receive queue types. These are used to tag * each transmit queue in the hardware and to identify a set * of transmit queues for operations such as start/stop dma. */ typedef enum { HAL_RX_QUEUE_HP = 0, /* high priority recv queue */ HAL_RX_QUEUE_LP = 1, /* low priority recv queue */ } HAL_RX_QUEUE; #define HAL_NUM_RX_QUEUES 2 /* max possible # of queues */ #define HAL_TXFIFO_DEPTH 8 /* transmit fifo depth */ /* * Transmit queue subtype. These map directly to * WME Access Categories (except for UPSD). Refer * to Table 5 of the WME spec. */ typedef enum { HAL_WME_AC_BK = 0, /* background access category */ HAL_WME_AC_BE = 1, /* best effort access category*/ HAL_WME_AC_VI = 2, /* video access category */ HAL_WME_AC_VO = 3, /* voice access category */ HAL_WME_UPSD = 4, /* uplink power save */ } HAL_TX_QUEUE_SUBTYPE; /* * Transmit queue flags that control various * operational parameters. */ typedef enum { /* * Per queue interrupt enables. When set the associated * interrupt may be delivered for packets sent through * the queue. Without these enabled no interrupts will * be delivered for transmits through the queue. */ HAL_TXQ_TXOKINT_ENABLE = 0x0001, /* enable TXOK interrupt */ HAL_TXQ_TXERRINT_ENABLE = 0x0001, /* enable TXERR interrupt */ HAL_TXQ_TXDESCINT_ENABLE = 0x0002, /* enable TXDESC interrupt */ HAL_TXQ_TXEOLINT_ENABLE = 0x0004, /* enable TXEOL interrupt */ HAL_TXQ_TXURNINT_ENABLE = 0x0008, /* enable TXURN interrupt */ /* * Enable hardware compression for packets sent through * the queue. The compression buffer must be setup and * packets must have a key entry marked in the tx descriptor. */ HAL_TXQ_COMPRESSION_ENABLE = 0x0010, /* enable h/w compression */ /* * Disable queue when veol is hit or ready time expires. * By default the queue is disabled only on reaching the * physical end of queue (i.e. a null link ptr in the * descriptor chain). */ HAL_TXQ_RDYTIME_EXP_POLICY_ENABLE = 0x0020, /* * Schedule frames on delivery of a DBA (DMA Beacon Alert) * event. Frames will be transmitted only when this timer * fires, e.g to transmit a beacon in ap or adhoc modes. */ HAL_TXQ_DBA_GATED = 0x0040, /* schedule based on DBA */ /* * Each transmit queue has a counter that is incremented * each time the queue is enabled and decremented when * the list of frames to transmit is traversed (or when * the ready time for the queue expires). This counter * must be non-zero for frames to be scheduled for * transmission. The following controls disable bumping * this counter under certain conditions. Typically this * is used to gate frames based on the contents of another * queue (e.g. CAB traffic may only follow a beacon frame). * These are meaningful only when frames are scheduled * with a non-ASAP policy (e.g. DBA-gated). */ HAL_TXQ_CBR_DIS_QEMPTY = 0x0080, /* disable on this q empty */ HAL_TXQ_CBR_DIS_BEMPTY = 0x0100, /* disable on beacon q empty */ /* * Fragment burst backoff policy. Normally the no backoff * is done after a successful transmission, the next fragment * is sent at SIFS. If this flag is set backoff is done * after each fragment, regardless whether it was ack'd or * not, after the backoff count reaches zero a normal channel * access procedure is done before the next transmit (i.e. * wait AIFS instead of SIFS). */ HAL_TXQ_FRAG_BURST_BACKOFF_ENABLE = 0x00800000, /* * Disable post-tx backoff following each frame. */ HAL_TXQ_BACKOFF_DISABLE = 0x00010000, /* disable post backoff */ /* * DCU arbiter lockout control. This controls how * lower priority tx queues are handled with respect to * to a specific queue when multiple queues have frames * to send. No lockout means lower priority queues arbitrate * concurrently with this queue. Intra-frame lockout * means lower priority queues are locked out until the * current frame transmits (e.g. including backoffs and bursting). * Global lockout means nothing lower can arbitrary so * long as there is traffic activity on this queue (frames, * backoff, etc). */ HAL_TXQ_ARB_LOCKOUT_INTRA = 0x00020000, /* intra-frame lockout */ HAL_TXQ_ARB_LOCKOUT_GLOBAL = 0x00040000, /* full lockout s */ HAL_TXQ_IGNORE_VIRTCOL = 0x00080000, /* ignore virt collisions */ HAL_TXQ_SEQNUM_INC_DIS = 0x00100000, /* disable seqnum increment */ } HAL_TX_QUEUE_FLAGS; typedef struct { uint32_t tqi_ver; /* hal TXQ version */ HAL_TX_QUEUE_SUBTYPE tqi_subtype; /* subtype if applicable */ HAL_TX_QUEUE_FLAGS tqi_qflags; /* flags (see above) */ uint32_t tqi_priority; /* (not used) */ uint32_t tqi_aifs; /* aifs */ uint32_t tqi_cwmin; /* cwMin */ uint32_t tqi_cwmax; /* cwMax */ uint16_t tqi_shretry; /* rts retry limit */ uint16_t tqi_lgretry; /* long retry limit (not used)*/ uint32_t tqi_cbrPeriod; /* CBR period (us) */ uint32_t tqi_cbrOverflowLimit; /* threshold for CBROVF int */ uint32_t tqi_burstTime; /* max burst duration (us) */ uint32_t tqi_readyTime; /* frame schedule time (us) */ uint32_t tqi_compBuf; /* comp buffer phys addr */ } HAL_TXQ_INFO; #define HAL_TQI_NONVAL 0xffff /* token to use for aifs, cwmin, cwmax */ #define HAL_TXQ_USEDEFAULT ((uint32_t) -1) /* compression definitions */ #define HAL_COMP_BUF_MAX_SIZE 9216 /* 9K */ #define HAL_COMP_BUF_ALIGN_SIZE 512 /* * Transmit packet types. This belongs in ah_desc.h, but * is here so we can give a proper type to various parameters * (and not require everyone include the file). * * NB: These values are intentionally assigned for * direct use when setting up h/w descriptors. */ typedef enum { HAL_PKT_TYPE_NORMAL = 0, HAL_PKT_TYPE_ATIM = 1, HAL_PKT_TYPE_PSPOLL = 2, HAL_PKT_TYPE_BEACON = 3, HAL_PKT_TYPE_PROBE_RESP = 4, HAL_PKT_TYPE_CHIRP = 5, HAL_PKT_TYPE_GRP_POLL = 6, HAL_PKT_TYPE_AMPDU = 7, } HAL_PKT_TYPE; /* Rx Filter Frame Types */ typedef enum { /* * These bits correspond to AR_RX_FILTER for all chips. * Not all bits are supported by all chips. */ HAL_RX_FILTER_UCAST = 0x00000001, /* Allow unicast frames */ HAL_RX_FILTER_MCAST = 0x00000002, /* Allow multicast frames */ HAL_RX_FILTER_BCAST = 0x00000004, /* Allow broadcast frames */ HAL_RX_FILTER_CONTROL = 0x00000008, /* Allow control frames */ HAL_RX_FILTER_BEACON = 0x00000010, /* Allow beacon frames */ HAL_RX_FILTER_PROM = 0x00000020, /* Promiscuous mode */ HAL_RX_FILTER_PROBEREQ = 0x00000080, /* Allow probe request frames */ HAL_RX_FILTER_PHYERR = 0x00000100, /* Allow phy errors */ HAL_RX_FILTER_MYBEACON = 0x00000200, /* Filter beacons other than mine */ HAL_RX_FILTER_COMPBAR = 0x00000400, /* Allow compressed BAR */ HAL_RX_FILTER_COMP_BA = 0x00000800, /* Allow compressed blockack */ HAL_RX_FILTER_PHYRADAR = 0x00002000, /* Allow phy radar errors */ HAL_RX_FILTER_PSPOLL = 0x00004000, /* Allow PS-POLL frames */ HAL_RX_FILTER_MCAST_BCAST_ALL = 0x00008000, /* Allow all mcast/bcast frames */ /* * Magic RX filter flags that aren't targeting hardware bits * but instead the HAL sets individual bits - eg PHYERR will result * in OFDM/CCK timing error frames being received. */ HAL_RX_FILTER_BSSID = 0x40000000, /* Disable BSSID match */ } HAL_RX_FILTER; typedef enum { HAL_PM_AWAKE = 0, HAL_PM_FULL_SLEEP = 1, HAL_PM_NETWORK_SLEEP = 2, HAL_PM_UNDEFINED = 3 } HAL_POWER_MODE; /* * Enterprise mode flags */ #define AH_ENT_DUAL_BAND_DISABLE 0x00000001 #define AH_ENT_CHAIN2_DISABLE 0x00000002 #define AH_ENT_5MHZ_DISABLE 0x00000004 #define AH_ENT_10MHZ_DISABLE 0x00000008 #define AH_ENT_49GHZ_DISABLE 0x00000010 #define AH_ENT_LOOPBACK_DISABLE 0x00000020 #define AH_ENT_TPC_PERF_DISABLE 0x00000040 #define AH_ENT_MIN_PKT_SIZE_DISABLE 0x00000080 #define AH_ENT_SPECTRAL_PRECISION 0x00000300 #define AH_ENT_SPECTRAL_PRECISION_S 8 #define AH_ENT_RTSCTS_DELIM_WAR 0x00010000 #define AH_FIRST_DESC_NDELIMS 60 /* * NOTE WELL: * These are mapped to take advantage of the common locations for many of * the bits on all of the currently supported MAC chips. This is to make * the ISR as efficient as possible, while still abstracting HW differences. * When new hardware breaks this commonality this enumerated type, as well * as the HAL functions using it, must be modified. All values are directly * mapped unless commented otherwise. */ typedef enum { HAL_INT_RX = 0x00000001, /* Non-common mapping */ HAL_INT_RXDESC = 0x00000002, /* Legacy mapping */ HAL_INT_RXERR = 0x00000004, HAL_INT_RXHP = 0x00000001, /* EDMA */ HAL_INT_RXLP = 0x00000002, /* EDMA */ HAL_INT_RXNOFRM = 0x00000008, HAL_INT_RXEOL = 0x00000010, HAL_INT_RXORN = 0x00000020, HAL_INT_TX = 0x00000040, /* Non-common mapping */ HAL_INT_TXDESC = 0x00000080, HAL_INT_TIM_TIMER= 0x00000100, HAL_INT_MCI = 0x00000200, HAL_INT_BBPANIC = 0x00000400, HAL_INT_TXURN = 0x00000800, HAL_INT_MIB = 0x00001000, HAL_INT_RXPHY = 0x00004000, HAL_INT_RXKCM = 0x00008000, HAL_INT_SWBA = 0x00010000, HAL_INT_BRSSI = 0x00020000, HAL_INT_BMISS = 0x00040000, HAL_INT_BNR = 0x00100000, HAL_INT_TIM = 0x00200000, /* Non-common mapping */ HAL_INT_DTIM = 0x00400000, /* Non-common mapping */ HAL_INT_DTIMSYNC= 0x00800000, /* Non-common mapping */ HAL_INT_GPIO = 0x01000000, HAL_INT_CABEND = 0x02000000, /* Non-common mapping */ HAL_INT_TSFOOR = 0x04000000, /* Non-common mapping */ HAL_INT_TBTT = 0x08000000, /* Non-common mapping */ /* Atheros ref driver has a generic timer interrupt now..*/ HAL_INT_GENTIMER = 0x08000000, /* Non-common mapping */ HAL_INT_CST = 0x10000000, /* Non-common mapping */ HAL_INT_GTT = 0x20000000, /* Non-common mapping */ HAL_INT_FATAL = 0x40000000, /* Non-common mapping */ #define HAL_INT_GLOBAL 0x80000000 /* Set/clear IER */ HAL_INT_BMISC = HAL_INT_TIM | HAL_INT_DTIM | HAL_INT_DTIMSYNC | HAL_INT_CABEND | HAL_INT_TBTT, /* Interrupt bits that map directly to ISR/IMR bits */ HAL_INT_COMMON = HAL_INT_RXNOFRM | HAL_INT_RXDESC | HAL_INT_RXEOL | HAL_INT_RXORN | HAL_INT_TXDESC | HAL_INT_TXURN | HAL_INT_MIB | HAL_INT_RXPHY | HAL_INT_RXKCM | HAL_INT_SWBA | HAL_INT_BMISS | HAL_INT_BRSSI | HAL_INT_BNR | HAL_INT_GPIO, } HAL_INT; /* * MSI vector assignments */ typedef enum { HAL_MSIVEC_MISC = 0, HAL_MSIVEC_TX = 1, HAL_MSIVEC_RXLP = 2, HAL_MSIVEC_RXHP = 3, } HAL_MSIVEC; typedef enum { HAL_INT_LINE = 0, HAL_INT_MSI = 1, } HAL_INT_TYPE; /* For interrupt mitigation registers */ typedef enum { HAL_INT_RX_FIRSTPKT=0, HAL_INT_RX_LASTPKT, HAL_INT_TX_FIRSTPKT, HAL_INT_TX_LASTPKT, HAL_INT_THRESHOLD } HAL_INT_MITIGATION; /* XXX this is duplicate information! */ typedef struct { u_int32_t cyclecnt_diff; /* delta cycle count */ u_int32_t rxclr_cnt; /* rx clear count */ u_int32_t extrxclr_cnt; /* ext chan rx clear count */ u_int32_t txframecnt_diff; /* delta tx frame count */ u_int32_t rxframecnt_diff; /* delta rx frame count */ u_int32_t listen_time; /* listen time in msec - time for which ch is free */ u_int32_t ofdmphyerr_cnt; /* OFDM err count since last reset */ u_int32_t cckphyerr_cnt; /* CCK err count since last reset */ u_int32_t ofdmphyerrcnt_diff; /* delta OFDM Phy Error Count */ HAL_BOOL valid; /* if the stats are valid*/ } HAL_ANISTATS; typedef struct { u_int8_t txctl_offset; u_int8_t txctl_numwords; u_int8_t txstatus_offset; u_int8_t txstatus_numwords; u_int8_t rxctl_offset; u_int8_t rxctl_numwords; u_int8_t rxstatus_offset; u_int8_t rxstatus_numwords; u_int8_t macRevision; } HAL_DESC_INFO; typedef enum { HAL_GPIO_OUTPUT_MUX_AS_OUTPUT = 0, HAL_GPIO_OUTPUT_MUX_PCIE_ATTENTION_LED = 1, HAL_GPIO_OUTPUT_MUX_PCIE_POWER_LED = 2, HAL_GPIO_OUTPUT_MUX_MAC_NETWORK_LED = 3, HAL_GPIO_OUTPUT_MUX_MAC_POWER_LED = 4, HAL_GPIO_OUTPUT_MUX_AS_WLAN_ACTIVE = 5, HAL_GPIO_OUTPUT_MUX_AS_TX_FRAME = 6, HAL_GPIO_OUTPUT_MUX_AS_MCI_WLAN_DATA, HAL_GPIO_OUTPUT_MUX_AS_MCI_WLAN_CLK, HAL_GPIO_OUTPUT_MUX_AS_MCI_BT_DATA, HAL_GPIO_OUTPUT_MUX_AS_MCI_BT_CLK, HAL_GPIO_OUTPUT_MUX_AS_WL_IN_TX, HAL_GPIO_OUTPUT_MUX_AS_WL_IN_RX, HAL_GPIO_OUTPUT_MUX_AS_BT_IN_TX, HAL_GPIO_OUTPUT_MUX_AS_BT_IN_RX, HAL_GPIO_OUTPUT_MUX_AS_RUCKUS_STROBE, HAL_GPIO_OUTPUT_MUX_AS_RUCKUS_DATA, HAL_GPIO_OUTPUT_MUX_AS_SMARTANT_CTRL0, HAL_GPIO_OUTPUT_MUX_AS_SMARTANT_CTRL1, HAL_GPIO_OUTPUT_MUX_AS_SMARTANT_CTRL2, HAL_GPIO_OUTPUT_MUX_NUM_ENTRIES } HAL_GPIO_MUX_TYPE; typedef enum { HAL_GPIO_INTR_LOW = 0, HAL_GPIO_INTR_HIGH = 1, HAL_GPIO_INTR_DISABLE = 2 } HAL_GPIO_INTR_TYPE; typedef struct halCounters { u_int32_t tx_frame_count; u_int32_t rx_frame_count; u_int32_t rx_clear_count; u_int32_t cycle_count; u_int8_t is_rx_active; // true (1) or false (0) u_int8_t is_tx_active; // true (1) or false (0) } HAL_COUNTERS; typedef enum { HAL_RFGAIN_INACTIVE = 0, HAL_RFGAIN_READ_REQUESTED = 1, HAL_RFGAIN_NEED_CHANGE = 2 } HAL_RFGAIN; typedef uint16_t HAL_CTRY_CODE; /* country code */ typedef uint16_t HAL_REG_DOMAIN; /* regulatory domain code */ #define HAL_ANTENNA_MIN_MODE 0 #define HAL_ANTENNA_FIXED_A 1 #define HAL_ANTENNA_FIXED_B 2 #define HAL_ANTENNA_MAX_MODE 3 typedef struct { uint32_t ackrcv_bad; uint32_t rts_bad; uint32_t rts_good; uint32_t fcs_bad; uint32_t beacons; } HAL_MIB_STATS; /* * These bits represent what's in ah_currentRDext. */ typedef enum { REG_EXT_FCC_MIDBAND = 0, REG_EXT_JAPAN_MIDBAND = 1, REG_EXT_FCC_DFS_HT40 = 2, REG_EXT_JAPAN_NONDFS_HT40 = 3, REG_EXT_JAPAN_DFS_HT40 = 4, REG_EXT_FCC_CH_144 = 5, } REG_EXT_BITMAP; enum { HAL_MODE_11A = 0x001, /* 11a channels */ HAL_MODE_TURBO = 0x002, /* 11a turbo-only channels */ HAL_MODE_11B = 0x004, /* 11b channels */ HAL_MODE_PUREG = 0x008, /* 11g channels (OFDM only) */ #ifdef notdef HAL_MODE_11G = 0x010, /* 11g channels (OFDM/CCK) */ #else HAL_MODE_11G = 0x008, /* XXX historical */ #endif HAL_MODE_108G = 0x020, /* 11g+Turbo channels */ HAL_MODE_108A = 0x040, /* 11a+Turbo channels */ HAL_MODE_11A_HALF_RATE = 0x200, /* 11a half width channels */ HAL_MODE_11A_QUARTER_RATE = 0x400, /* 11a quarter width channels */ HAL_MODE_11G_HALF_RATE = 0x800, /* 11g half width channels */ HAL_MODE_11G_QUARTER_RATE = 0x1000, /* 11g quarter width channels */ HAL_MODE_11NG_HT20 = 0x008000, HAL_MODE_11NA_HT20 = 0x010000, HAL_MODE_11NG_HT40PLUS = 0x020000, HAL_MODE_11NG_HT40MINUS = 0x040000, HAL_MODE_11NA_HT40PLUS = 0x080000, HAL_MODE_11NA_HT40MINUS = 0x100000, HAL_MODE_ALL = 0xffffff }; typedef struct { int rateCount; /* NB: for proper padding */ uint8_t rateCodeToIndex[256]; /* back mapping */ struct { uint8_t valid; /* valid for rate control use */ uint8_t phy; /* CCK/OFDM/XR */ uint32_t rateKbps; /* transfer rate in kbs */ uint8_t rateCode; /* rate for h/w descriptors */ uint8_t shortPreamble; /* mask for enabling short * preamble in CCK rate code */ uint8_t dot11Rate; /* value for supported rates * info element of MLME */ uint8_t controlRate; /* index of next lower basic * rate; used for dur. calcs */ uint16_t lpAckDuration; /* long preamble ACK duration */ uint16_t spAckDuration; /* short preamble ACK duration*/ } info[64]; } HAL_RATE_TABLE; typedef struct { u_int rs_count; /* number of valid entries */ uint8_t rs_rates[64]; /* rates */ } HAL_RATE_SET; /* * 802.11n specific structures and enums */ typedef enum { HAL_CHAINTYPE_TX = 1, /* Tx chain type */ HAL_CHAINTYPE_RX = 2, /* RX chain type */ } HAL_CHAIN_TYPE; typedef struct { u_int Tries; u_int Rate; /* hardware rate code */ u_int RateIndex; /* rate series table index */ u_int PktDuration; u_int ChSel; u_int RateFlags; #define HAL_RATESERIES_RTS_CTS 0x0001 /* use rts/cts w/this series */ #define HAL_RATESERIES_2040 0x0002 /* use ext channel for series */ #define HAL_RATESERIES_HALFGI 0x0004 /* use half-gi for series */ #define HAL_RATESERIES_STBC 0x0008 /* use STBC for series */ u_int tx_power_cap; /* in 1/2 dBm units XXX TODO */ } HAL_11N_RATE_SERIES; typedef enum { HAL_HT_MACMODE_20 = 0, /* 20 MHz operation */ HAL_HT_MACMODE_2040 = 1, /* 20/40 MHz operation */ } HAL_HT_MACMODE; typedef enum { HAL_HT_PHYMODE_20 = 0, /* 20 MHz operation */ HAL_HT_PHYMODE_2040 = 1, /* 20/40 MHz operation */ } HAL_HT_PHYMODE; typedef enum { HAL_HT_EXTPROTSPACING_20 = 0, /* 20 MHz spacing */ HAL_HT_EXTPROTSPACING_25 = 1, /* 25 MHz spacing */ } HAL_HT_EXTPROTSPACING; typedef enum { HAL_RX_CLEAR_CTL_LOW = 0x1, /* force control channel to appear busy */ HAL_RX_CLEAR_EXT_LOW = 0x2, /* force extension channel to appear busy */ } HAL_HT_RXCLEAR; typedef enum { HAL_FREQ_BAND_5GHZ = 0, HAL_FREQ_BAND_2GHZ = 1, } HAL_FREQ_BAND; /* * Antenna switch control. By default antenna selection * enables multiple (2) antenna use. To force use of the * A or B antenna only specify a fixed setting. Fixing * the antenna will also disable any diversity support. */ typedef enum { HAL_ANT_VARIABLE = 0, /* variable by programming */ HAL_ANT_FIXED_A = 1, /* fixed antenna A */ HAL_ANT_FIXED_B = 2, /* fixed antenna B */ } HAL_ANT_SETTING; typedef enum { HAL_M_STA = 1, /* infrastructure station */ HAL_M_IBSS = 0, /* IBSS (adhoc) station */ HAL_M_HOSTAP = 6, /* Software Access Point */ HAL_M_MONITOR = 8 /* Monitor mode */ } HAL_OPMODE; typedef enum { HAL_RESET_NORMAL = 0, /* Do normal reset */ HAL_RESET_BBPANIC = 1, /* Reset because of BB panic */ HAL_RESET_FORCE_COLD = 2, /* Force full reset */ } HAL_RESET_TYPE; +enum { + HAL_RESET_POWER_ON, + HAL_RESET_WARM, + HAL_RESET_COLD +}; + typedef struct { uint8_t kv_type; /* one of HAL_CIPHER */ uint8_t kv_apsd; /* Mask for APSD enabled ACs */ uint16_t kv_len; /* length in bits */ uint8_t kv_val[16]; /* enough for 128-bit keys */ uint8_t kv_mic[8]; /* TKIP MIC key */ uint8_t kv_txmic[8]; /* TKIP TX MIC key (optional) */ } HAL_KEYVAL; /* * This is the TX descriptor field which marks the key padding requirement. * The naming is unfortunately unclear. */ #define AH_KEYTYPE_MASK 0x0F typedef enum { HAL_KEY_TYPE_CLEAR, HAL_KEY_TYPE_WEP, HAL_KEY_TYPE_AES, HAL_KEY_TYPE_TKIP, } HAL_KEY_TYPE; typedef enum { HAL_CIPHER_WEP = 0, HAL_CIPHER_AES_OCB = 1, HAL_CIPHER_AES_CCM = 2, HAL_CIPHER_CKIP = 3, HAL_CIPHER_TKIP = 4, HAL_CIPHER_CLR = 5, /* no encryption */ HAL_CIPHER_MIC = 127 /* TKIP-MIC, not a cipher */ } HAL_CIPHER; enum { HAL_SLOT_TIME_6 = 6, /* NB: for turbo mode */ HAL_SLOT_TIME_9 = 9, HAL_SLOT_TIME_20 = 20, }; /* * Per-station beacon timer state. Note that the specified * beacon interval (given in TU's) can also include flags * to force a TSF reset and to enable the beacon xmit logic. * If bs_cfpmaxduration is non-zero the hardware is setup to * coexist with a PCF-capable AP. */ typedef struct { uint32_t bs_nexttbtt; /* next beacon in TU */ uint32_t bs_nextdtim; /* next DTIM in TU */ uint32_t bs_intval; /* beacon interval+flags */ /* * HAL_BEACON_PERIOD, HAL_BEACON_ENA and HAL_BEACON_RESET_TSF * are all 1:1 correspondances with the pre-11n chip AR_BEACON * register. */ #define HAL_BEACON_PERIOD 0x0000ffff /* beacon interval period */ #define HAL_BEACON_PERIOD_TU8 0x0007ffff /* beacon interval, tu/8 */ #define HAL_BEACON_ENA 0x00800000 /* beacon xmit enable */ #define HAL_BEACON_RESET_TSF 0x01000000 /* clear TSF */ #define HAL_TSFOOR_THRESHOLD 0x00004240 /* TSF OOR thresh (16k uS) */ uint32_t bs_dtimperiod; uint16_t bs_cfpperiod; /* CFP period in TU */ uint16_t bs_cfpmaxduration; /* max CFP duration in TU */ uint32_t bs_cfpnext; /* next CFP in TU */ uint16_t bs_timoffset; /* byte offset to TIM bitmap */ uint16_t bs_bmissthreshold; /* beacon miss threshold */ uint32_t bs_sleepduration; /* max sleep duration */ uint32_t bs_tsfoor_threshold; /* TSF out of range threshold */ } HAL_BEACON_STATE; /* * Like HAL_BEACON_STATE but for non-station mode setup. * NB: see above flag definitions for bt_intval. */ typedef struct { uint32_t bt_intval; /* beacon interval+flags */ uint32_t bt_nexttbtt; /* next beacon in TU */ uint32_t bt_nextatim; /* next ATIM in TU */ uint32_t bt_nextdba; /* next DBA in 1/8th TU */ uint32_t bt_nextswba; /* next SWBA in 1/8th TU */ uint32_t bt_flags; /* timer enables */ #define HAL_BEACON_TBTT_EN 0x00000001 #define HAL_BEACON_DBA_EN 0x00000002 #define HAL_BEACON_SWBA_EN 0x00000004 } HAL_BEACON_TIMERS; /* * Per-node statistics maintained by the driver for use in * optimizing signal quality and other operational aspects. */ typedef struct { uint32_t ns_avgbrssi; /* average beacon rssi */ uint32_t ns_avgrssi; /* average data rssi */ uint32_t ns_avgtxrssi; /* average tx rssi */ } HAL_NODE_STATS; #define HAL_RSSI_EP_MULTIPLIER (1<<7) /* pow2 to optimize out * and / */ /* * This is the ANI state and MIB stats. * * It's used by the HAL modules to keep state /and/ by the debug ioctl * to fetch ANI information. */ typedef struct { uint32_t ast_ani_niup; /* ANI increased noise immunity */ uint32_t ast_ani_nidown; /* ANI decreased noise immunity */ uint32_t ast_ani_spurup; /* ANI increased spur immunity */ uint32_t ast_ani_spurdown;/* ANI descreased spur immunity */ uint32_t ast_ani_ofdmon; /* ANI OFDM weak signal detect on */ uint32_t ast_ani_ofdmoff;/* ANI OFDM weak signal detect off */ uint32_t ast_ani_cckhigh;/* ANI CCK weak signal threshold high */ uint32_t ast_ani_ccklow; /* ANI CCK weak signal threshold low */ uint32_t ast_ani_stepup; /* ANI increased first step level */ uint32_t ast_ani_stepdown;/* ANI decreased first step level */ uint32_t ast_ani_ofdmerrs;/* ANI cumulative ofdm phy err count */ uint32_t ast_ani_cckerrs;/* ANI cumulative cck phy err count */ uint32_t ast_ani_reset; /* ANI parameters zero'd for non-STA */ uint32_t ast_ani_lzero; /* ANI listen time forced to zero */ uint32_t ast_ani_lneg; /* ANI listen time calculated < 0 */ HAL_MIB_STATS ast_mibstats; /* MIB counter stats */ HAL_NODE_STATS ast_nodestats; /* Latest rssi stats from driver */ } HAL_ANI_STATS; typedef struct { uint8_t noiseImmunityLevel; uint8_t spurImmunityLevel; uint8_t firstepLevel; uint8_t ofdmWeakSigDetectOff; uint8_t cckWeakSigThreshold; uint32_t listenTime; /* NB: intentionally ordered so data exported to user space is first */ uint32_t txFrameCount; /* Last txFrameCount */ uint32_t rxFrameCount; /* Last rx Frame count */ uint32_t cycleCount; /* Last cycleCount (to detect wrap-around) */ uint32_t ofdmPhyErrCount;/* OFDM err count since last reset */ uint32_t cckPhyErrCount; /* CCK err count since last reset */ } HAL_ANI_STATE; struct ath_desc; struct ath_tx_status; struct ath_rx_status; struct ieee80211_channel; /* * This is a channel survey sample entry. * * The AR5212 ANI routines fill these samples. The ANI code then uses it * when calculating listen time; it is also exported via a diagnostic * API. */ typedef struct { uint32_t seq_num; uint32_t tx_busy; uint32_t rx_busy; uint32_t chan_busy; uint32_t ext_chan_busy; uint32_t cycle_count; /* XXX TODO */ uint32_t ofdm_phyerr_count; uint32_t cck_phyerr_count; } HAL_SURVEY_SAMPLE; /* * This provides 3.2 seconds of sample space given an * ANI time of 1/10th of a second. This may not be enough! */ #define CHANNEL_SURVEY_SAMPLE_COUNT 32 typedef struct { HAL_SURVEY_SAMPLE samples[CHANNEL_SURVEY_SAMPLE_COUNT]; uint32_t cur_sample; /* current sample in sequence */ uint32_t cur_seq; /* current sequence number */ } HAL_CHANNEL_SURVEY; /* * ANI commands. * * These are used both internally and externally via the diagnostic * API. * * Note that this is NOT the ANI commands being used via the INTMIT * capability - that has a different mapping for some reason. */ typedef enum { HAL_ANI_PRESENT = 0, /* is ANI support present */ HAL_ANI_NOISE_IMMUNITY_LEVEL = 1, /* set level */ HAL_ANI_OFDM_WEAK_SIGNAL_DETECTION = 2, /* enable/disable */ HAL_ANI_CCK_WEAK_SIGNAL_THR = 3, /* enable/disable */ HAL_ANI_FIRSTEP_LEVEL = 4, /* set level */ HAL_ANI_SPUR_IMMUNITY_LEVEL = 5, /* set level */ HAL_ANI_MODE = 6, /* 0 => manual, 1 => auto (XXX do not change) */ HAL_ANI_PHYERR_RESET = 7, /* reset phy error stats */ HAL_ANI_MRC_CCK = 8, } HAL_ANI_CMD; #define HAL_ANI_ALL 0xffffffff /* * This is the layout of the ANI INTMIT capability. * * Notice that the command values differ to HAL_ANI_CMD. */ typedef enum { HAL_CAP_INTMIT_PRESENT = 0, HAL_CAP_INTMIT_ENABLE = 1, HAL_CAP_INTMIT_NOISE_IMMUNITY_LEVEL = 2, HAL_CAP_INTMIT_OFDM_WEAK_SIGNAL_LEVEL = 3, HAL_CAP_INTMIT_CCK_WEAK_SIGNAL_THR = 4, HAL_CAP_INTMIT_FIRSTEP_LEVEL = 5, HAL_CAP_INTMIT_SPUR_IMMUNITY_LEVEL = 6 } HAL_CAP_INTMIT_CMD; typedef struct { int32_t pe_firpwr; /* FIR pwr out threshold */ int32_t pe_rrssi; /* Radar rssi thresh */ int32_t pe_height; /* Pulse height thresh */ int32_t pe_prssi; /* Pulse rssi thresh */ int32_t pe_inband; /* Inband thresh */ /* The following params are only for AR5413 and later */ u_int32_t pe_relpwr; /* Relative power threshold in 0.5dB steps */ u_int32_t pe_relstep; /* Pulse Relative step threshold in 0.5dB steps */ u_int32_t pe_maxlen; /* Max length of radar sign in 0.8us units */ int32_t pe_usefir128; /* Use the average in-band power measured over 128 cycles */ int32_t pe_blockradar; /* * Enable to block radar check if pkt detect is done via OFDM * weak signal detect or pkt is detected immediately after tx * to rx transition */ int32_t pe_enmaxrssi; /* * Enable to use the max rssi instead of the last rssi during * fine gain changes for radar detection */ int32_t pe_extchannel; /* Enable DFS on ext channel */ int32_t pe_enabled; /* Whether radar detection is enabled */ int32_t pe_enrelpwr; int32_t pe_en_relstep_check; } HAL_PHYERR_PARAM; #define HAL_PHYERR_PARAM_NOVAL 65535 typedef struct { u_int16_t ss_fft_period; /* Skip interval for FFT reports */ u_int16_t ss_period; /* Spectral scan period */ u_int16_t ss_count; /* # of reports to return from ss_active */ u_int16_t ss_short_report;/* Set to report ony 1 set of FFT results */ u_int8_t radar_bin_thresh_sel; /* strong signal radar FFT threshold configuration */ u_int16_t ss_spectral_pri; /* are we doing a noise power cal ? */ int8_t ss_nf_cal[AH_MAX_CHAINS*2]; /* nf calibrated values for ctl+ext from eeprom */ int8_t ss_nf_pwr[AH_MAX_CHAINS*2]; /* nf pwr values for ctl+ext from eeprom */ int32_t ss_nf_temp_data; /* temperature data taken during nf scan */ int ss_enabled; int ss_active; } HAL_SPECTRAL_PARAM; #define HAL_SPECTRAL_PARAM_NOVAL 0xFFFF #define HAL_SPECTRAL_PARAM_ENABLE 0x8000 /* Enable/Disable if applicable */ /* * DFS operating mode flags. */ typedef enum { HAL_DFS_UNINIT_DOMAIN = 0, /* Uninitialized dfs domain */ HAL_DFS_FCC_DOMAIN = 1, /* FCC3 dfs domain */ HAL_DFS_ETSI_DOMAIN = 2, /* ETSI dfs domain */ HAL_DFS_MKK4_DOMAIN = 3, /* Japan dfs domain */ } HAL_DFS_DOMAIN; /* * MFP decryption options for initializing the MAC. */ typedef enum { HAL_MFP_QOSDATA = 0, /* Decrypt MFP frames like QoS data frames. All chips before Merlin. */ HAL_MFP_PASSTHRU, /* Don't decrypt MFP frames at all. Passthrough */ HAL_MFP_HW_CRYPTO /* hardware decryption enabled. Merlin can do it. */ } HAL_MFP_OPT_T; /* LNA config supported */ typedef enum { HAL_ANT_DIV_COMB_LNA1_MINUS_LNA2 = 0, HAL_ANT_DIV_COMB_LNA2 = 1, HAL_ANT_DIV_COMB_LNA1 = 2, HAL_ANT_DIV_COMB_LNA1_PLUS_LNA2 = 3, } HAL_ANT_DIV_COMB_LNA_CONF; typedef struct { u_int8_t main_lna_conf; u_int8_t alt_lna_conf; u_int8_t fast_div_bias; u_int8_t main_gaintb; u_int8_t alt_gaintb; u_int8_t antdiv_configgroup; int8_t lna1_lna2_delta; } HAL_ANT_COMB_CONFIG; #define DEFAULT_ANTDIV_CONFIG_GROUP 0x00 #define HAL_ANTDIV_CONFIG_GROUP_1 0x01 #define HAL_ANTDIV_CONFIG_GROUP_2 0x02 #define HAL_ANTDIV_CONFIG_GROUP_3 0x03 /* * Flag for setting QUIET period */ typedef enum { HAL_QUIET_DISABLE = 0x0, HAL_QUIET_ENABLE = 0x1, HAL_QUIET_ADD_CURRENT_TSF = 0x2, /* add current TSF to next_start offset */ HAL_QUIET_ADD_SWBA_RESP_TIME = 0x4, /* add beacon response time to next_start offset */ } HAL_QUIET_FLAG; #define HAL_DFS_EVENT_PRICH 0x0000001 #define HAL_DFS_EVENT_EXTCH 0x0000002 #define HAL_DFS_EVENT_EXTEARLY 0x0000004 #define HAL_DFS_EVENT_ISDC 0x0000008 struct hal_dfs_event { uint64_t re_full_ts; /* 64-bit full timestamp from interrupt time */ uint32_t re_ts; /* Original 15 bit recv timestamp */ uint8_t re_rssi; /* rssi of radar event */ uint8_t re_dur; /* duration of radar pulse */ uint32_t re_flags; /* Flags (see above) */ }; typedef struct hal_dfs_event HAL_DFS_EVENT; /* * Generic Timer domain */ typedef enum { HAL_GEN_TIMER_TSF = 0, HAL_GEN_TIMER_TSF2, HAL_GEN_TIMER_TSF_ANY } HAL_GEN_TIMER_DOMAIN; /* * BT Co-existence definitions */ #include "ath_hal/ah_btcoex.h" struct hal_bb_panic_info { u_int32_t status; u_int32_t tsf; u_int32_t phy_panic_wd_ctl1; u_int32_t phy_panic_wd_ctl2; u_int32_t phy_gen_ctrl; u_int32_t rxc_pcnt; u_int32_t rxf_pcnt; u_int32_t txf_pcnt; u_int32_t cycles; u_int32_t wd; u_int32_t det; u_int32_t rdar; u_int32_t r_odfm; u_int32_t r_cck; u_int32_t t_odfm; u_int32_t t_cck; u_int32_t agc; u_int32_t src; }; /* Serialize Register Access Mode */ typedef enum { SER_REG_MODE_OFF = 0, SER_REG_MODE_ON = 1, SER_REG_MODE_AUTO = 2, } SER_REG_MODE; typedef struct { int ah_debug; /* only used if AH_DEBUG is defined */ int ah_ar5416_biasadj; /* enable AR2133 radio specific bias fiddling */ /* NB: these are deprecated; they exist for now for compatibility */ int ah_dma_beacon_response_time;/* in TU's */ int ah_sw_beacon_response_time; /* in TU's */ int ah_additional_swba_backoff; /* in TU's */ int ah_force_full_reset; /* force full chip reset rather then warm reset */ int ah_serialise_reg_war; /* force serialisation of register IO */ /* XXX these don't belong here, they're just for the ar9300 HAL port effort */ int ath_hal_desc_tpc; /* Per-packet TPC */ int ath_hal_sta_update_tx_pwr_enable; /* GreenTX */ int ath_hal_sta_update_tx_pwr_enable_S1; /* GreenTX */ int ath_hal_sta_update_tx_pwr_enable_S2; /* GreenTX */ int ath_hal_sta_update_tx_pwr_enable_S3; /* GreenTX */ /* I'm not sure what the default values for these should be */ int ath_hal_pll_pwr_save; int ath_hal_pcie_power_save_enable; int ath_hal_intr_mitigation_rx; int ath_hal_intr_mitigation_tx; int ath_hal_pcie_clock_req; #define AR_PCIE_PLL_PWRSAVE_CONTROL (1<<0) #define AR_PCIE_PLL_PWRSAVE_ON_D3 (1<<1) #define AR_PCIE_PLL_PWRSAVE_ON_D0 (1<<2) int ath_hal_pcie_waen; int ath_hal_pcie_ser_des_write; /* these are important for correct AR9300 behaviour */ int ath_hal_ht_enable; /* needs to be enabled for AR9300 HT */ int ath_hal_diversity_control; int ath_hal_antenna_switch_swap; int ath_hal_ext_lna_ctl_gpio; int ath_hal_spur_mode; int ath_hal_6mb_ack; /* should set this to 1 for 11a/11na? */ int ath_hal_enable_msi; /* enable MSI interrupts (needed?) */ int ath_hal_beacon_filter_interval; /* ok to be 0 for now? */ /* For now, set this to 0 - net80211 needs to know about hardware MFP support */ int ath_hal_mfp_support; int ath_hal_enable_ani; /* should set this.. */ int ath_hal_cwm_ignore_ext_cca; int ath_hal_show_bb_panic; int ath_hal_ant_ctrl_comm2g_switch_enable; int ath_hal_ext_atten_margin_cfg; int ath_hal_min_gainidx; int ath_hal_war70c; uint32_t ath_hal_mci_config; } HAL_OPS_CONFIG; /* * Hardware Access Layer (HAL) API. * * Clients of the HAL call ath_hal_attach to obtain a reference to an * ath_hal structure for use with the device. Hardware-related operations * that follow must call back into the HAL through interface, supplying * the reference as the first parameter. Note that before using the * reference returned by ath_hal_attach the caller should verify the * ABI version number. */ struct ath_hal { uint32_t ah_magic; /* consistency check magic number */ uint16_t ah_devid; /* PCI device ID */ uint16_t ah_subvendorid; /* PCI subvendor ID */ HAL_SOFTC ah_sc; /* back pointer to driver/os state */ HAL_BUS_TAG ah_st; /* params for register r+w */ HAL_BUS_HANDLE ah_sh; HAL_CTRY_CODE ah_countryCode; uint32_t ah_macVersion; /* MAC version id */ uint16_t ah_macRev; /* MAC revision */ uint16_t ah_phyRev; /* PHY revision */ /* NB: when only one radio is present the rev is in 5Ghz */ uint16_t ah_analog5GhzRev;/* 5GHz radio revision */ uint16_t ah_analog2GhzRev;/* 2GHz radio revision */ uint16_t *ah_eepromdata; /* eeprom buffer, if needed */ uint32_t ah_intrstate[8]; /* last int state */ uint32_t ah_syncstate; /* last sync intr state */ /* Current powerstate from HAL calls */ HAL_POWER_MODE ah_powerMode; HAL_OPS_CONFIG ah_config; const HAL_RATE_TABLE *__ahdecl(*ah_getRateTable)(struct ath_hal *, u_int mode); void __ahdecl(*ah_detach)(struct ath_hal*); /* Reset functions */ HAL_BOOL __ahdecl(*ah_reset)(struct ath_hal *, HAL_OPMODE, struct ieee80211_channel *, HAL_BOOL bChannelChange, HAL_RESET_TYPE resetType, HAL_STATUS *status); HAL_BOOL __ahdecl(*ah_phyDisable)(struct ath_hal *); HAL_BOOL __ahdecl(*ah_disable)(struct ath_hal *); void __ahdecl(*ah_configPCIE)(struct ath_hal *, HAL_BOOL restore, HAL_BOOL power_off); void __ahdecl(*ah_disablePCIE)(struct ath_hal *); void __ahdecl(*ah_setPCUConfig)(struct ath_hal *); HAL_BOOL __ahdecl(*ah_perCalibration)(struct ath_hal*, struct ieee80211_channel *, HAL_BOOL *); HAL_BOOL __ahdecl(*ah_perCalibrationN)(struct ath_hal *, struct ieee80211_channel *, u_int chainMask, HAL_BOOL longCal, HAL_BOOL *isCalDone); HAL_BOOL __ahdecl(*ah_resetCalValid)(struct ath_hal *, const struct ieee80211_channel *); HAL_BOOL __ahdecl(*ah_setTxPower)(struct ath_hal *, const struct ieee80211_channel *, uint16_t *); HAL_BOOL __ahdecl(*ah_setTxPowerLimit)(struct ath_hal *, uint32_t); HAL_BOOL __ahdecl(*ah_setBoardValues)(struct ath_hal *, const struct ieee80211_channel *); /* Transmit functions */ HAL_BOOL __ahdecl(*ah_updateTxTrigLevel)(struct ath_hal*, HAL_BOOL incTrigLevel); int __ahdecl(*ah_setupTxQueue)(struct ath_hal *, HAL_TX_QUEUE, const HAL_TXQ_INFO *qInfo); HAL_BOOL __ahdecl(*ah_setTxQueueProps)(struct ath_hal *, int q, const HAL_TXQ_INFO *qInfo); HAL_BOOL __ahdecl(*ah_getTxQueueProps)(struct ath_hal *, int q, HAL_TXQ_INFO *qInfo); HAL_BOOL __ahdecl(*ah_releaseTxQueue)(struct ath_hal *ah, u_int q); HAL_BOOL __ahdecl(*ah_resetTxQueue)(struct ath_hal *ah, u_int q); uint32_t __ahdecl(*ah_getTxDP)(struct ath_hal*, u_int); HAL_BOOL __ahdecl(*ah_setTxDP)(struct ath_hal*, u_int, uint32_t txdp); uint32_t __ahdecl(*ah_numTxPending)(struct ath_hal *, u_int q); HAL_BOOL __ahdecl(*ah_startTxDma)(struct ath_hal*, u_int); HAL_BOOL __ahdecl(*ah_stopTxDma)(struct ath_hal*, u_int); HAL_BOOL __ahdecl(*ah_setupTxDesc)(struct ath_hal *, struct ath_desc *, u_int pktLen, u_int hdrLen, HAL_PKT_TYPE type, u_int txPower, u_int txRate0, u_int txTries0, u_int keyIx, u_int antMode, u_int flags, u_int rtsctsRate, u_int rtsctsDuration, u_int compicvLen, u_int compivLen, u_int comp); HAL_BOOL __ahdecl(*ah_setupXTxDesc)(struct ath_hal *, struct ath_desc*, u_int txRate1, u_int txTries1, u_int txRate2, u_int txTries2, u_int txRate3, u_int txTries3); HAL_BOOL __ahdecl(*ah_fillTxDesc)(struct ath_hal *, struct ath_desc *, HAL_DMA_ADDR *bufAddrList, uint32_t *segLenList, u_int descId, u_int qcuId, HAL_BOOL firstSeg, HAL_BOOL lastSeg, const struct ath_desc *); HAL_STATUS __ahdecl(*ah_procTxDesc)(struct ath_hal *, struct ath_desc *, struct ath_tx_status *); void __ahdecl(*ah_getTxIntrQueue)(struct ath_hal *, uint32_t *); void __ahdecl(*ah_reqTxIntrDesc)(struct ath_hal *, struct ath_desc*); HAL_BOOL __ahdecl(*ah_getTxCompletionRates)(struct ath_hal *, const struct ath_desc *ds, int *rates, int *tries); void __ahdecl(*ah_setTxDescLink)(struct ath_hal *ah, void *ds, uint32_t link); void __ahdecl(*ah_getTxDescLink)(struct ath_hal *ah, void *ds, uint32_t *link); void __ahdecl(*ah_getTxDescLinkPtr)(struct ath_hal *ah, void *ds, uint32_t **linkptr); void __ahdecl(*ah_setupTxStatusRing)(struct ath_hal *, void *ts_start, uint32_t ts_paddr_start, uint16_t size); void __ahdecl(*ah_getTxRawTxDesc)(struct ath_hal *, u_int32_t *); /* Receive Functions */ uint32_t __ahdecl(*ah_getRxDP)(struct ath_hal*, HAL_RX_QUEUE); void __ahdecl(*ah_setRxDP)(struct ath_hal*, uint32_t rxdp, HAL_RX_QUEUE); void __ahdecl(*ah_enableReceive)(struct ath_hal*); HAL_BOOL __ahdecl(*ah_stopDmaReceive)(struct ath_hal*); void __ahdecl(*ah_startPcuReceive)(struct ath_hal*); void __ahdecl(*ah_stopPcuReceive)(struct ath_hal*); void __ahdecl(*ah_setMulticastFilter)(struct ath_hal*, uint32_t filter0, uint32_t filter1); HAL_BOOL __ahdecl(*ah_setMulticastFilterIndex)(struct ath_hal*, uint32_t index); HAL_BOOL __ahdecl(*ah_clrMulticastFilterIndex)(struct ath_hal*, uint32_t index); uint32_t __ahdecl(*ah_getRxFilter)(struct ath_hal*); void __ahdecl(*ah_setRxFilter)(struct ath_hal*, uint32_t); HAL_BOOL __ahdecl(*ah_setupRxDesc)(struct ath_hal *, struct ath_desc *, uint32_t size, u_int flags); HAL_STATUS __ahdecl(*ah_procRxDesc)(struct ath_hal *, struct ath_desc *, uint32_t phyAddr, struct ath_desc *next, uint64_t tsf, struct ath_rx_status *); void __ahdecl(*ah_rxMonitor)(struct ath_hal *, const HAL_NODE_STATS *, const struct ieee80211_channel *); void __ahdecl(*ah_aniPoll)(struct ath_hal *, const struct ieee80211_channel *); void __ahdecl(*ah_procMibEvent)(struct ath_hal *, const HAL_NODE_STATS *); /* Misc Functions */ HAL_STATUS __ahdecl(*ah_getCapability)(struct ath_hal *, HAL_CAPABILITY_TYPE, uint32_t capability, uint32_t *result); HAL_BOOL __ahdecl(*ah_setCapability)(struct ath_hal *, HAL_CAPABILITY_TYPE, uint32_t capability, uint32_t setting, HAL_STATUS *); HAL_BOOL __ahdecl(*ah_getDiagState)(struct ath_hal *, int request, const void *args, uint32_t argsize, void **result, uint32_t *resultsize); void __ahdecl(*ah_getMacAddress)(struct ath_hal *, uint8_t *); HAL_BOOL __ahdecl(*ah_setMacAddress)(struct ath_hal *, const uint8_t*); void __ahdecl(*ah_getBssIdMask)(struct ath_hal *, uint8_t *); HAL_BOOL __ahdecl(*ah_setBssIdMask)(struct ath_hal *, const uint8_t*); HAL_BOOL __ahdecl(*ah_setRegulatoryDomain)(struct ath_hal*, uint16_t, HAL_STATUS *); void __ahdecl(*ah_setLedState)(struct ath_hal*, HAL_LED_STATE); void __ahdecl(*ah_writeAssocid)(struct ath_hal*, const uint8_t *bssid, uint16_t assocId); HAL_BOOL __ahdecl(*ah_gpioCfgOutput)(struct ath_hal *, uint32_t gpio, HAL_GPIO_MUX_TYPE); HAL_BOOL __ahdecl(*ah_gpioCfgInput)(struct ath_hal *, uint32_t gpio); uint32_t __ahdecl(*ah_gpioGet)(struct ath_hal *, uint32_t gpio); HAL_BOOL __ahdecl(*ah_gpioSet)(struct ath_hal *, uint32_t gpio, uint32_t val); void __ahdecl(*ah_gpioSetIntr)(struct ath_hal*, u_int, uint32_t); uint32_t __ahdecl(*ah_getTsf32)(struct ath_hal*); uint64_t __ahdecl(*ah_getTsf64)(struct ath_hal*); void __ahdecl(*ah_setTsf64)(struct ath_hal *, uint64_t); void __ahdecl(*ah_resetTsf)(struct ath_hal*); HAL_BOOL __ahdecl(*ah_detectCardPresent)(struct ath_hal*); void __ahdecl(*ah_updateMibCounters)(struct ath_hal*, HAL_MIB_STATS*); HAL_RFGAIN __ahdecl(*ah_getRfGain)(struct ath_hal*); u_int __ahdecl(*ah_getDefAntenna)(struct ath_hal*); void __ahdecl(*ah_setDefAntenna)(struct ath_hal*, u_int); HAL_ANT_SETTING __ahdecl(*ah_getAntennaSwitch)(struct ath_hal*); HAL_BOOL __ahdecl(*ah_setAntennaSwitch)(struct ath_hal*, HAL_ANT_SETTING); HAL_BOOL __ahdecl(*ah_setSifsTime)(struct ath_hal*, u_int); u_int __ahdecl(*ah_getSifsTime)(struct ath_hal*); HAL_BOOL __ahdecl(*ah_setSlotTime)(struct ath_hal*, u_int); u_int __ahdecl(*ah_getSlotTime)(struct ath_hal*); HAL_BOOL __ahdecl(*ah_setAckTimeout)(struct ath_hal*, u_int); u_int __ahdecl(*ah_getAckTimeout)(struct ath_hal*); HAL_BOOL __ahdecl(*ah_setAckCTSRate)(struct ath_hal*, u_int); u_int __ahdecl(*ah_getAckCTSRate)(struct ath_hal*); HAL_BOOL __ahdecl(*ah_setCTSTimeout)(struct ath_hal*, u_int); u_int __ahdecl(*ah_getCTSTimeout)(struct ath_hal*); HAL_BOOL __ahdecl(*ah_setDecompMask)(struct ath_hal*, uint16_t, int); void __ahdecl(*ah_setCoverageClass)(struct ath_hal*, uint8_t, int); HAL_STATUS __ahdecl(*ah_setQuiet)(struct ath_hal *ah, uint32_t period, uint32_t duration, uint32_t nextStart, HAL_QUIET_FLAG flag); void __ahdecl(*ah_setChainMasks)(struct ath_hal *, uint32_t, uint32_t); /* DFS functions */ void __ahdecl(*ah_enableDfs)(struct ath_hal *ah, HAL_PHYERR_PARAM *pe); void __ahdecl(*ah_getDfsThresh)(struct ath_hal *ah, HAL_PHYERR_PARAM *pe); HAL_BOOL __ahdecl(*ah_getDfsDefaultThresh)(struct ath_hal *ah, HAL_PHYERR_PARAM *pe); HAL_BOOL __ahdecl(*ah_procRadarEvent)(struct ath_hal *ah, struct ath_rx_status *rxs, uint64_t fulltsf, const char *buf, HAL_DFS_EVENT *event); HAL_BOOL __ahdecl(*ah_isFastClockEnabled)(struct ath_hal *ah); void __ahdecl(*ah_setDfsCacTxQuiet)(struct ath_hal *, HAL_BOOL); /* Spectral Scan functions */ void __ahdecl(*ah_spectralConfigure)(struct ath_hal *ah, HAL_SPECTRAL_PARAM *sp); void __ahdecl(*ah_spectralGetConfig)(struct ath_hal *ah, HAL_SPECTRAL_PARAM *sp); void __ahdecl(*ah_spectralStart)(struct ath_hal *); void __ahdecl(*ah_spectralStop)(struct ath_hal *); HAL_BOOL __ahdecl(*ah_spectralIsEnabled)(struct ath_hal *); HAL_BOOL __ahdecl(*ah_spectralIsActive)(struct ath_hal *); /* XXX getNfPri() and getNfExt() */ /* Key Cache Functions */ uint32_t __ahdecl(*ah_getKeyCacheSize)(struct ath_hal*); HAL_BOOL __ahdecl(*ah_resetKeyCacheEntry)(struct ath_hal*, uint16_t); HAL_BOOL __ahdecl(*ah_isKeyCacheEntryValid)(struct ath_hal *, uint16_t); HAL_BOOL __ahdecl(*ah_setKeyCacheEntry)(struct ath_hal*, uint16_t, const HAL_KEYVAL *, const uint8_t *, int); HAL_BOOL __ahdecl(*ah_setKeyCacheEntryMac)(struct ath_hal*, uint16_t, const uint8_t *); /* Power Management Functions */ HAL_BOOL __ahdecl(*ah_setPowerMode)(struct ath_hal*, HAL_POWER_MODE mode, int setChip); HAL_POWER_MODE __ahdecl(*ah_getPowerMode)(struct ath_hal*); int16_t __ahdecl(*ah_getChanNoise)(struct ath_hal *, const struct ieee80211_channel *); /* Beacon Management Functions */ void __ahdecl(*ah_setBeaconTimers)(struct ath_hal*, const HAL_BEACON_TIMERS *); /* NB: deprecated, use ah_setBeaconTimers instead */ void __ahdecl(*ah_beaconInit)(struct ath_hal *, uint32_t nexttbtt, uint32_t intval); void __ahdecl(*ah_setStationBeaconTimers)(struct ath_hal*, const HAL_BEACON_STATE *); void __ahdecl(*ah_resetStationBeaconTimers)(struct ath_hal*); uint64_t __ahdecl(*ah_getNextTBTT)(struct ath_hal *); /* 802.11n Functions */ HAL_BOOL __ahdecl(*ah_chainTxDesc)(struct ath_hal *, struct ath_desc *, HAL_DMA_ADDR *bufAddrList, uint32_t *segLenList, u_int, u_int, HAL_PKT_TYPE, u_int, HAL_CIPHER, uint8_t, HAL_BOOL, HAL_BOOL, HAL_BOOL); HAL_BOOL __ahdecl(*ah_setupFirstTxDesc)(struct ath_hal *, struct ath_desc *, u_int, u_int, u_int, u_int, u_int, u_int, u_int, u_int); HAL_BOOL __ahdecl(*ah_setupLastTxDesc)(struct ath_hal *, struct ath_desc *, const struct ath_desc *); void __ahdecl(*ah_set11nRateScenario)(struct ath_hal *, struct ath_desc *, u_int, u_int, HAL_11N_RATE_SERIES [], u_int, u_int); /* * The next 4 (set11ntxdesc -> set11naggrlast) are specific * to the EDMA HAL. Descriptors are chained together by * using filltxdesc (not ChainTxDesc) and then setting the * aggregate flags appropriately using first/middle/last. */ void __ahdecl(*ah_set11nTxDesc)(struct ath_hal *, void *, u_int, HAL_PKT_TYPE, u_int, u_int, u_int); void __ahdecl(*ah_set11nAggrFirst)(struct ath_hal *, struct ath_desc *, u_int, u_int); void __ahdecl(*ah_set11nAggrMiddle)(struct ath_hal *, struct ath_desc *, u_int); void __ahdecl(*ah_set11nAggrLast)(struct ath_hal *, struct ath_desc *); void __ahdecl(*ah_clr11nAggr)(struct ath_hal *, struct ath_desc *); void __ahdecl(*ah_set11nBurstDuration)(struct ath_hal *, struct ath_desc *, u_int); void __ahdecl(*ah_set11nVirtMoreFrag)(struct ath_hal *, struct ath_desc *, u_int); HAL_BOOL __ahdecl(*ah_getMibCycleCounts) (struct ath_hal *, HAL_SURVEY_SAMPLE *); uint32_t __ahdecl(*ah_get11nExtBusy)(struct ath_hal *); void __ahdecl(*ah_set11nMac2040)(struct ath_hal *, HAL_HT_MACMODE); HAL_HT_RXCLEAR __ahdecl(*ah_get11nRxClear)(struct ath_hal *ah); void __ahdecl(*ah_set11nRxClear)(struct ath_hal *, HAL_HT_RXCLEAR); /* Interrupt functions */ HAL_BOOL __ahdecl(*ah_isInterruptPending)(struct ath_hal*); HAL_BOOL __ahdecl(*ah_getPendingInterrupts)(struct ath_hal*, HAL_INT*); HAL_INT __ahdecl(*ah_getInterrupts)(struct ath_hal*); HAL_INT __ahdecl(*ah_setInterrupts)(struct ath_hal*, HAL_INT); /* Bluetooth Coexistence functions */ void __ahdecl(*ah_btCoexSetInfo)(struct ath_hal *, HAL_BT_COEX_INFO *); void __ahdecl(*ah_btCoexSetConfig)(struct ath_hal *, HAL_BT_COEX_CONFIG *); void __ahdecl(*ah_btCoexSetQcuThresh)(struct ath_hal *, int); void __ahdecl(*ah_btCoexSetWeights)(struct ath_hal *, uint32_t); void __ahdecl(*ah_btCoexSetBmissThresh)(struct ath_hal *, uint32_t); void __ahdecl(*ah_btCoexSetParameter)(struct ath_hal *, uint32_t, uint32_t); void __ahdecl(*ah_btCoexDisable)(struct ath_hal *); int __ahdecl(*ah_btCoexEnable)(struct ath_hal *); /* Bluetooth MCI methods */ void __ahdecl(*ah_btMciSetup)(struct ath_hal *, uint32_t, void *, uint16_t, uint32_t); HAL_BOOL __ahdecl(*ah_btMciSendMessage)(struct ath_hal *, uint8_t, uint32_t, uint32_t *, uint8_t, HAL_BOOL, HAL_BOOL); uint32_t __ahdecl(*ah_btMciGetInterrupt)(struct ath_hal *, uint32_t *, uint32_t *); uint32_t __ahdecl(*ah_btMciState)(struct ath_hal *, uint32_t, uint32_t *); void __ahdecl(*ah_btMciDetach)(struct ath_hal *); /* LNA diversity configuration */ void __ahdecl(*ah_divLnaConfGet)(struct ath_hal *, HAL_ANT_COMB_CONFIG *); void __ahdecl(*ah_divLnaConfSet)(struct ath_hal *, HAL_ANT_COMB_CONFIG *); }; /* * Check the PCI vendor ID and device ID against Atheros' values * and return a printable description for any Atheros hardware. * AH_NULL is returned if the ID's do not describe Atheros hardware. */ extern const char *__ahdecl ath_hal_probe(uint16_t vendorid, uint16_t devid); /* * Attach the HAL for use with the specified device. The device is * defined by the PCI device ID. The caller provides an opaque pointer * to an upper-layer data structure (HAL_SOFTC) that is stored in the * HAL state block for later use. Hardware register accesses are done * using the specified bus tag and handle. On successful return a * reference to a state block is returned that must be supplied in all * subsequent HAL calls. Storage associated with this reference is * dynamically allocated and must be freed by calling the ah_detach * method when the client is done. If the attach operation fails a * null (AH_NULL) reference will be returned and a status code will * be returned if the status parameter is non-zero. */ extern struct ath_hal * __ahdecl ath_hal_attach(uint16_t devid, HAL_SOFTC, HAL_BUS_TAG, HAL_BUS_HANDLE, uint16_t *eepromdata, HAL_OPS_CONFIG *ah_config, HAL_STATUS* status); extern const char *ath_hal_mac_name(struct ath_hal *); extern const char *ath_hal_rf_name(struct ath_hal *); /* * Regulatory interfaces. Drivers should use ath_hal_init_channels to * request a set of channels for a particular country code and/or * regulatory domain. If CTRY_DEFAULT and SKU_NONE are specified then * this list is constructed according to the contents of the EEPROM. * ath_hal_getchannels acts similarly but does not alter the operating * state; this can be used to collect information for a particular * regulatory configuration. Finally ath_hal_set_channels installs a * channel list constructed outside the driver. The HAL will adopt the * channel list and setup internal state according to the specified * regulatory configuration (e.g. conformance test limits). * * For all interfaces the channel list is returned in the supplied array. * maxchans defines the maximum size of this array. nchans contains the * actual number of channels returned. If a problem occurred then a * status code != HAL_OK is returned. */ struct ieee80211_channel; /* * Return a list of channels according to the specified regulatory. */ extern HAL_STATUS __ahdecl ath_hal_getchannels(struct ath_hal *, struct ieee80211_channel *chans, u_int maxchans, int *nchans, u_int modeSelect, HAL_CTRY_CODE cc, HAL_REG_DOMAIN regDmn, HAL_BOOL enableExtendedChannels); /* * Return a list of channels and install it as the current operating * regulatory list. */ extern HAL_STATUS __ahdecl ath_hal_init_channels(struct ath_hal *, struct ieee80211_channel *chans, u_int maxchans, int *nchans, u_int modeSelect, HAL_CTRY_CODE cc, HAL_REG_DOMAIN rd, HAL_BOOL enableExtendedChannels); /* * Install the list of channels as the current operating regulatory * and setup related state according to the country code and sku. */ extern HAL_STATUS __ahdecl ath_hal_set_channels(struct ath_hal *, struct ieee80211_channel *chans, int nchans, HAL_CTRY_CODE cc, HAL_REG_DOMAIN regDmn); /* * Fetch the ctl/ext noise floor values reported by a MIMO * radio. Returns 1 for valid results, 0 for invalid channel. */ extern int __ahdecl ath_hal_get_mimo_chan_noise(struct ath_hal *ah, const struct ieee80211_channel *chan, int16_t *nf_ctl, int16_t *nf_ext); /* * Calibrate noise floor data following a channel scan or similar. * This must be called prior retrieving noise floor data. */ extern void __ahdecl ath_hal_process_noisefloor(struct ath_hal *ah); /* * Return bit mask of wireless modes supported by the hardware. */ extern u_int __ahdecl ath_hal_getwirelessmodes(struct ath_hal*); /* * Get the HAL wireless mode for the given channel. */ extern int ath_hal_get_curmode(struct ath_hal *ah, const struct ieee80211_channel *chan); /* * Calculate the packet TX time for a legacy or 11n frame */ extern uint32_t __ahdecl ath_hal_pkt_txtime(struct ath_hal *ah, const HAL_RATE_TABLE *rates, uint32_t frameLen, uint16_t rateix, HAL_BOOL isht40, HAL_BOOL shortPreamble, HAL_BOOL includeSifs); /* * Calculate the duration of an 11n frame. */ extern uint32_t __ahdecl ath_computedur_ht(uint32_t frameLen, uint16_t rate, int streams, HAL_BOOL isht40, HAL_BOOL isShortGI); /* * Calculate the transmit duration of a legacy frame. */ extern uint16_t __ahdecl ath_hal_computetxtime(struct ath_hal *, const HAL_RATE_TABLE *rates, uint32_t frameLen, uint16_t rateix, HAL_BOOL shortPreamble, HAL_BOOL includeSifs); /* * Adjust the TSF. */ extern void __ahdecl ath_hal_adjusttsf(struct ath_hal *ah, int32_t tsfdelta); /* * Enable or disable CCA. */ void __ahdecl ath_hal_setcca(struct ath_hal *ah, int ena); /* * Get CCA setting. */ int __ahdecl ath_hal_getcca(struct ath_hal *ah); /* * Enable/disable and get self-gen frame (ACK, CTS) for CAC. */ void __ahdecl ath_hal_set_dfs_cac_tx_quiet(struct ath_hal *ah, HAL_BOOL ena); /* * Read EEPROM data from ah_eepromdata */ HAL_BOOL __ahdecl ath_hal_EepromDataRead(struct ath_hal *ah, u_int off, uint16_t *data); /* * For now, simply pass through MFP frames. */ static inline u_int32_t ath_hal_get_mfp_qos(struct ath_hal *ah) { //return AH_PRIVATE(ah)->ah_mfp_qos; return HAL_MFP_QOSDATA; } /* * Convert between microseconds and core system clocks. */ extern u_int ath_hal_mac_clks(struct ath_hal *ah, u_int usecs); extern u_int ath_hal_mac_usec(struct ath_hal *ah, u_int clks); extern uint64_t ath_hal_mac_psec(struct ath_hal *ah, u_int clks); #endif /* _ATH_AH_H_ */ Index: head/sys/dev/ath/ath_hal/ar5416/ar5416.h =================================================================== --- head/sys/dev/ath/ath_hal/ar5416/ar5416.h (revision 334196) +++ head/sys/dev/ath/ath_hal/ar5416/ar5416.h (revision 334197) @@ -1,428 +1,422 @@ /*- * SPDX-License-Identifier: ISC * * Copyright (c) 2002-2009 Sam Leffler, Errno Consulting * Copyright (c) 2002-2008 Atheros Communications, Inc. * * Permission to use, copy, modify, and/or distribute this software for any * purpose with or without fee is hereby granted, provided that the above * copyright notice and this permission notice appear in all copies. * * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE. * * $FreeBSD$ */ #ifndef _ATH_AR5416_H_ #define _ATH_AR5416_H_ #include "ar5212/ar5212.h" #include "ar5416_cal.h" #include "ah_eeprom_v14.h" /* for CAL_TARGET_POWER_* */ #define AR5416_MAGIC 0x20065416 -enum { - HAL_RESET_POWER_ON, - HAL_RESET_WARM, - HAL_RESET_COLD, -}; - typedef struct { uint16_t synth_center; uint16_t ctl_center; uint16_t ext_center; } CHAN_CENTERS; typedef enum Ar5416_Rates { rate6mb, rate9mb, rate12mb, rate18mb, rate24mb, rate36mb, rate48mb, rate54mb, rate1l, rate2l, rate2s, rate5_5l, rate5_5s, rate11l, rate11s, rateXr, rateHt20_0, rateHt20_1, rateHt20_2, rateHt20_3, rateHt20_4, rateHt20_5, rateHt20_6, rateHt20_7, rateHt40_0, rateHt40_1, rateHt40_2, rateHt40_3, rateHt40_4, rateHt40_5, rateHt40_6, rateHt40_7, rateDupCck, rateDupOfdm, rateExtCck, rateExtOfdm, Ar5416RateSize } AR5416_RATES; #define AR5416_DEFAULT_RXCHAINMASK 7 #define AR5416_DEFAULT_TXCHAINMASK 1 #define AR5416_MAX_RATE_POWER 63 #define AR5416_KEYTABLE_SIZE 128 #define AR5416_CCA_MAX_GOOD_VALUE -85 #define AR5416_CCA_MAX_HIGH_VALUE -62 #define AR5416_CCA_MIN_BAD_VALUE -140 #define AR9285_CCA_MAX_GOOD_VALUE -118 #define AR5416_SPUR_RSSI_THRESH 40 struct ar5416NfLimits { int16_t max; int16_t min; int16_t nominal; }; struct ath_hal_5416 { struct ath_hal_5212 ah_5212; /* NB: RF data setup at attach */ HAL_INI_ARRAY ah_ini_bb_rfgain; HAL_INI_ARRAY ah_ini_bank0; HAL_INI_ARRAY ah_ini_bank1; HAL_INI_ARRAY ah_ini_bank2; HAL_INI_ARRAY ah_ini_bank3; HAL_INI_ARRAY ah_ini_bank6; HAL_INI_ARRAY ah_ini_bank7; HAL_INI_ARRAY ah_ini_addac; HAL_INI_ARRAY ah_ini_pcieserdes; void (*ah_writeIni)(struct ath_hal *, const struct ieee80211_channel *); void (*ah_spurMitigate)(struct ath_hal *, const struct ieee80211_channel *); /* calibration ops */ HAL_BOOL (*ah_cal_initcal)(struct ath_hal *, const struct ieee80211_channel *); void (*ah_cal_pacal)(struct ath_hal *, HAL_BOOL is_reset); /* optional open-loop tx power control related methods */ void (*ah_olcInit)(struct ath_hal *); void (*ah_olcTempCompensation)(struct ath_hal *); /* tx power control */ HAL_BOOL (*ah_setPowerCalTable) (struct ath_hal *ah, struct ar5416eeprom *pEepData, const struct ieee80211_channel *chan, int16_t *pTxPowerIndexOffset); /* baseband operations */ void (*ah_initPLL) (struct ath_hal *ah, const struct ieee80211_channel *chan); /* bluetooth coexistence operations */ void (*ah_btCoexSetDiversity)(struct ath_hal *ah); u_int ah_globaltxtimeout; /* global tx timeout */ u_int ah_gpioMask; int ah_hangs; /* h/w hangs state */ uint8_t ah_keytype[AR5416_KEYTABLE_SIZE]; /* * Primary/Extension Channel Tx, Rx, Rx Clear State */ uint32_t ah_cycleCount; uint32_t ah_ctlBusy; uint32_t ah_extBusy; uint32_t ah_rxBusy; uint32_t ah_txBusy; uint32_t ah_rx_chainmask; uint32_t ah_tx_chainmask; HAL_ANI_CMD ah_ani_function; struct ar5416PerCal ah_cal; /* periodic calibration state */ struct ar5416NfLimits nf_2g; struct ar5416NfLimits nf_5g; /* * TX power configuration related structures */ int initPDADC; int ah_ht40PowerIncForPdadc; int16_t ah_ratesArray[Ar5416RateSize]; int ah_need_an_top2_fixup; /* merlin or later chips that may need this workaround */ /* * Bluetooth coexistence static setup according to the registry */ HAL_BT_MODULE ah_btModule; /* Bluetooth module identifier */ uint8_t ah_btCoexConfigType; /* BT coex configuration */ uint8_t ah_btActiveGpioSelect; /* GPIO pin for BT_ACTIVE */ uint8_t ah_btPriorityGpioSelect; /* GPIO pin for BT_PRIORITY */ uint8_t ah_wlanActiveGpioSelect; /* GPIO pin for WLAN_ACTIVE */ uint8_t ah_btActivePolarity; /* Polarity of BT_ACTIVE */ HAL_BOOL ah_btCoexSingleAnt; /* Single or dual antenna configuration */ uint8_t ah_btWlanIsolation; /* Isolation between BT and WLAN in dB */ /* * Bluetooth coexistence runtime settings */ HAL_BOOL ah_btCoexEnabled; /* If Bluetooth coexistence is enabled */ uint32_t ah_btCoexMode; /* Register setting for AR_BT_COEX_MODE */ uint32_t ah_btCoexBTWeight; /* Register setting for AR_BT_COEX_WEIGHT */ uint32_t ah_btCoexWLANWeight; /* Register setting for AR_BT_COEX_WEIGHT */ uint32_t ah_btCoexMode2; /* Register setting for AR_BT_COEX_MODE2 */ uint32_t ah_btCoexFlag; /* Special tuning flags for BT coex */ }; #define AH5416(_ah) ((struct ath_hal_5416 *)(_ah)) #define IS_5416_PCI(ah) ((AH_PRIVATE(ah)->ah_macVersion) == AR_SREV_VERSION_OWL_PCI) #define IS_5416_PCIE(ah) ((AH_PRIVATE(ah)->ah_macVersion) == AR_SREV_VERSION_OWL_PCIE) #undef IS_PCIE #define IS_PCIE(ah) (IS_5416_PCIE(ah)) extern HAL_BOOL ar2133RfAttach(struct ath_hal *, HAL_STATUS *); struct ath_hal; extern uint32_t ar5416GetRadioRev(struct ath_hal *ah); extern void ar5416InitState(struct ath_hal_5416 *, uint16_t devid, HAL_SOFTC sc, HAL_BUS_TAG st, HAL_BUS_HANDLE sh, HAL_STATUS *status); extern void ar5416Detach(struct ath_hal *ah); extern void ar5416AttachPCIE(struct ath_hal *ah); extern HAL_BOOL ar5416FillCapabilityInfo(struct ath_hal *ah); extern void ar5416AniAttach(struct ath_hal *, const struct ar5212AniParams *, const struct ar5212AniParams *, HAL_BOOL ena); extern void ar5416AniDetach(struct ath_hal *); extern HAL_BOOL ar5416AniControl(struct ath_hal *, HAL_ANI_CMD cmd, int param); extern HAL_BOOL ar5416AniSetParams(struct ath_hal *, const struct ar5212AniParams *, const struct ar5212AniParams *); extern void ar5416ProcessMibIntr(struct ath_hal *, const HAL_NODE_STATS *); extern void ar5416RxMonitor(struct ath_hal *, const HAL_NODE_STATS *, const struct ieee80211_channel *); extern void ar5416AniPoll(struct ath_hal *, const struct ieee80211_channel *); extern void ar5416AniReset(struct ath_hal *, const struct ieee80211_channel *, HAL_OPMODE, int); extern void ar5416SetBeaconTimers(struct ath_hal *, const HAL_BEACON_TIMERS *); extern void ar5416BeaconInit(struct ath_hal *ah, uint32_t next_beacon, uint32_t beacon_period); extern void ar5416ResetStaBeaconTimers(struct ath_hal *ah); extern void ar5416SetStaBeaconTimers(struct ath_hal *ah, const HAL_BEACON_STATE *); extern uint64_t ar5416GetNextTBTT(struct ath_hal *); /* ar5416_btcoex.c */ extern void ar5416SetBTCoexInfo(struct ath_hal *ah, HAL_BT_COEX_INFO *btinfo); extern void ar5416BTCoexConfig(struct ath_hal *ah, HAL_BT_COEX_CONFIG *btconf); extern void ar5416BTCoexAntennaDiversity(struct ath_hal *ah); extern void ar5416BTCoexSetQcuThresh(struct ath_hal *ah, int qnum); extern void ar5416BTCoexSetWeights(struct ath_hal *ah, uint32_t stompType); extern void ar5416BTCoexSetupBmissThresh(struct ath_hal *ah, uint32_t thresh); extern void ar5416BTCoexSetParameter(struct ath_hal *ah, uint32_t type, uint32_t value); extern void ar5416BTCoexDisable(struct ath_hal *ah); extern int ar5416BTCoexEnable(struct ath_hal *ah); extern void ar5416InitBTCoex(struct ath_hal *ah); extern HAL_BOOL ar5416EepromRead(struct ath_hal *, u_int off, uint16_t *data); extern HAL_BOOL ar5416EepromWrite(struct ath_hal *, u_int off, uint16_t data); extern HAL_BOOL ar5416IsInterruptPending(struct ath_hal *ah); extern HAL_BOOL ar5416GetPendingInterrupts(struct ath_hal *, HAL_INT *masked); extern HAL_INT ar5416SetInterrupts(struct ath_hal *ah, HAL_INT ints); extern HAL_BOOL ar5416GpioCfgOutput(struct ath_hal *, uint32_t gpio, HAL_GPIO_MUX_TYPE); extern HAL_BOOL ar5416GpioCfgInput(struct ath_hal *, uint32_t gpio); extern HAL_BOOL ar5416GpioSet(struct ath_hal *, uint32_t gpio, uint32_t val); extern uint32_t ar5416GpioGet(struct ath_hal *ah, uint32_t gpio); extern void ar5416GpioSetIntr(struct ath_hal *ah, u_int, uint32_t ilevel); extern u_int ar5416GetWirelessModes(struct ath_hal *ah); extern void ar5416SetLedState(struct ath_hal *ah, HAL_LED_STATE state); extern uint64_t ar5416GetTsf64(struct ath_hal *ah); extern void ar5416SetTsf64(struct ath_hal *ah, uint64_t tsf64); extern void ar5416ResetTsf(struct ath_hal *ah); extern uint32_t ar5416GetCurRssi(struct ath_hal *ah); extern HAL_BOOL ar5416SetAntennaSwitch(struct ath_hal *, HAL_ANT_SETTING); extern HAL_BOOL ar5416SetDecompMask(struct ath_hal *, uint16_t, int); extern void ar5416SetCoverageClass(struct ath_hal *, uint8_t, int); extern HAL_BOOL ar5416GetMibCycleCounts(struct ath_hal *ah, HAL_SURVEY_SAMPLE *hsample); extern void ar5416SetChainMasks(struct ath_hal *ah, uint32_t, uint32_t); extern uint32_t ar5416Get11nExtBusy(struct ath_hal *ah); extern void ar5416Set11nMac2040(struct ath_hal *ah, HAL_HT_MACMODE mode); extern HAL_HT_RXCLEAR ar5416Get11nRxClear(struct ath_hal *ah); extern void ar5416Set11nRxClear(struct ath_hal *ah, HAL_HT_RXCLEAR rxclear); extern HAL_STATUS ar5416SetQuiet(struct ath_hal *ah, uint32_t period, uint32_t duration, uint32_t nextStart, HAL_QUIET_FLAG flag); extern HAL_STATUS ar5416GetCapability(struct ath_hal *ah, HAL_CAPABILITY_TYPE type, uint32_t capability, uint32_t *result); extern HAL_BOOL ar5416SetCapability(struct ath_hal *ah, HAL_CAPABILITY_TYPE type, uint32_t capability, uint32_t val, HAL_STATUS *status); extern HAL_BOOL ar5416GetDiagState(struct ath_hal *ah, int request, const void *args, uint32_t argsize, void **result, uint32_t *resultsize); extern HAL_BOOL ar5416SetRifsDelay(struct ath_hal *ah, const struct ieee80211_channel *chan, HAL_BOOL enable); extern void ar5416EnableDfs(struct ath_hal *ah, HAL_PHYERR_PARAM *pe); extern HAL_BOOL ar5416GetDfsDefaultThresh(struct ath_hal *ah, HAL_PHYERR_PARAM *pe); extern void ar5416GetDfsThresh(struct ath_hal *ah, HAL_PHYERR_PARAM *pe); extern HAL_BOOL ar5416ProcessRadarEvent(struct ath_hal *ah, struct ath_rx_status *rxs, uint64_t fulltsf, const char *buf, HAL_DFS_EVENT *event); extern HAL_BOOL ar5416IsFastClockEnabled(struct ath_hal *ah); /* ar9280_spectral.c */ extern void ar5416ConfigureSpectralScan(struct ath_hal *ah, HAL_SPECTRAL_PARAM *ss); extern void ar5416GetSpectralParams(struct ath_hal *ah, HAL_SPECTRAL_PARAM *ss); extern HAL_BOOL ar5416IsSpectralActive(struct ath_hal *ah); extern HAL_BOOL ar5416IsSpectralEnabled(struct ath_hal *ah); extern void ar5416StartSpectralScan(struct ath_hal *ah); extern void ar5416StopSpectralScan(struct ath_hal *ah); extern uint32_t ar5416GetSpectralConfig(struct ath_hal *ah); extern void ar5416RestoreSpectralConfig(struct ath_hal *ah, uint32_t restoreval); extern HAL_BOOL ar5416SetPowerMode(struct ath_hal *ah, HAL_POWER_MODE mode, int setChip); extern HAL_POWER_MODE ar5416GetPowerMode(struct ath_hal *ah); extern HAL_BOOL ar5416GetPowerStatus(struct ath_hal *ah); extern HAL_BOOL ar5416ResetKeyCacheEntry(struct ath_hal *ah, uint16_t entry); extern HAL_BOOL ar5416SetKeyCacheEntry(struct ath_hal *ah, uint16_t entry, const HAL_KEYVAL *k, const uint8_t *mac, int xorKey); extern uint32_t ar5416GetRxFilter(struct ath_hal *ah); extern void ar5416SetRxFilter(struct ath_hal *ah, uint32_t bits); extern HAL_BOOL ar5416StopDmaReceive(struct ath_hal *ah); extern void ar5416StartPcuReceive(struct ath_hal *ah); extern void ar5416StopPcuReceive(struct ath_hal *ah); extern HAL_BOOL ar5416SetupRxDesc(struct ath_hal *, struct ath_desc *, uint32_t size, u_int flags); extern HAL_STATUS ar5416ProcRxDesc(struct ath_hal *ah, struct ath_desc *, uint32_t, struct ath_desc *, uint64_t, struct ath_rx_status *); extern HAL_BOOL ar5416Reset(struct ath_hal *ah, HAL_OPMODE opmode, struct ieee80211_channel *chan, HAL_BOOL bChannelChange, HAL_RESET_TYPE, HAL_STATUS *status); extern HAL_BOOL ar5416PhyDisable(struct ath_hal *ah); extern HAL_RFGAIN ar5416GetRfgain(struct ath_hal *ah); extern HAL_BOOL ar5416Disable(struct ath_hal *ah); extern HAL_BOOL ar5416ChipReset(struct ath_hal *ah, const struct ieee80211_channel *); extern int ar5416GetRegChainOffset(struct ath_hal *ah, int i); extern HAL_BOOL ar5416SetBoardValues(struct ath_hal *, const struct ieee80211_channel *); extern HAL_BOOL ar5416SetResetReg(struct ath_hal *, uint32_t type); extern HAL_BOOL ar5416SetTxPowerLimit(struct ath_hal *ah, uint32_t limit); extern HAL_BOOL ar5416SetTransmitPower(struct ath_hal *, const struct ieee80211_channel *, uint16_t *); extern HAL_BOOL ar5416GetChipPowerLimits(struct ath_hal *ah, struct ieee80211_channel *chan); extern void ar5416GetChannelCenters(struct ath_hal *, const struct ieee80211_channel *chan, CHAN_CENTERS *centers); extern void ar5416SetRatesArrayFromTargetPower(struct ath_hal *ah, const struct ieee80211_channel *chan, int16_t *ratesArray, const CAL_TARGET_POWER_LEG *targetPowerCck, const CAL_TARGET_POWER_LEG *targetPowerCckExt, const CAL_TARGET_POWER_LEG *targetPowerOfdm, const CAL_TARGET_POWER_LEG *targetPowerOfdmExt, const CAL_TARGET_POWER_HT *targetPowerHt20, const CAL_TARGET_POWER_HT *targetPowerHt40); extern void ar5416GetTargetPowers(struct ath_hal *ah, const struct ieee80211_channel *chan, CAL_TARGET_POWER_HT *powInfo, uint16_t numChannels, CAL_TARGET_POWER_HT *pNewPower, uint16_t numRates, HAL_BOOL isHt40Target); extern void ar5416GetTargetPowersLeg(struct ath_hal *ah, const struct ieee80211_channel *chan, CAL_TARGET_POWER_LEG *powInfo, uint16_t numChannels, CAL_TARGET_POWER_LEG *pNewPower, uint16_t numRates, HAL_BOOL isExtTarget); extern void ar5416InitChainMasks(struct ath_hal *ah); extern void ar5416RestoreChainMask(struct ath_hal *ah); extern void ar5416EepromSetAddac(struct ath_hal *ah, const struct ieee80211_channel *chan); extern uint16_t ar5416GetMaxEdgePower(uint16_t freq, CAL_CTL_EDGES *pRdEdgesPower, HAL_BOOL is2GHz); extern void ar5416InitPLL(struct ath_hal *ah, const struct ieee80211_channel *chan); /* TX power setup related routines in ar5416_reset.c */ extern void ar5416GetGainBoundariesAndPdadcs(struct ath_hal *ah, const struct ieee80211_channel *chan, CAL_DATA_PER_FREQ *pRawDataSet, uint8_t * bChans, uint16_t availPiers, uint16_t tPdGainOverlap, int16_t *pMinCalPower, uint16_t * pPdGainBoundaries, uint8_t * pPDADCValues, uint16_t numXpdGains); extern void ar5416SetGainBoundariesClosedLoop(struct ath_hal *ah, int i, uint16_t pdGainOverlap_t2, uint16_t gainBoundaries[]); extern uint16_t ar5416GetXpdGainValues(struct ath_hal *ah, uint16_t xpdMask, uint16_t xpdGainValues[]); extern void ar5416WriteDetectorGainBiases(struct ath_hal *ah, uint16_t numXpdGain, uint16_t xpdGainValues[]); extern void ar5416WritePdadcValues(struct ath_hal *ah, int i, uint8_t pdadcValues[]); extern HAL_BOOL ar5416SetPowerCalTable(struct ath_hal *ah, struct ar5416eeprom *pEepData, const struct ieee80211_channel *chan, int16_t *pTxPowerIndexOffset); extern void ar5416WriteTxPowerRateRegisters(struct ath_hal *ah, const struct ieee80211_channel *chan, const int16_t ratesArray[]); extern HAL_BOOL ar5416StopTxDma(struct ath_hal *ah, u_int q); extern HAL_BOOL ar5416SetupTxDesc(struct ath_hal *ah, struct ath_desc *ds, u_int pktLen, u_int hdrLen, HAL_PKT_TYPE type, u_int txPower, u_int txRate0, u_int txTries0, u_int keyIx, u_int antMode, u_int flags, u_int rtsctsRate, u_int rtsctsDuration, u_int compicvLen, u_int compivLen, u_int comp); extern HAL_BOOL ar5416SetupXTxDesc(struct ath_hal *, struct ath_desc *, u_int txRate1, u_int txRetries1, u_int txRate2, u_int txRetries2, u_int txRate3, u_int txRetries3); extern HAL_BOOL ar5416FillTxDesc(struct ath_hal *ah, struct ath_desc *ds, HAL_DMA_ADDR *bufAddrList, uint32_t *segLenList, u_int descId, u_int qcuId, HAL_BOOL firstSeg, HAL_BOOL lastSeg, const struct ath_desc *ds0); extern HAL_STATUS ar5416ProcTxDesc(struct ath_hal *ah, struct ath_desc *, struct ath_tx_status *); extern HAL_BOOL ar5416GetTxCompletionRates(struct ath_hal *ah, const struct ath_desc *ds0, int *rates, int *tries); extern HAL_BOOL ar5416ResetTxQueue(struct ath_hal *ah, u_int q); extern int ar5416SetupTxQueue(struct ath_hal *ah, HAL_TX_QUEUE type, const HAL_TXQ_INFO *qInfo); extern HAL_BOOL ar5416ChainTxDesc(struct ath_hal *ah, struct ath_desc *ds, HAL_DMA_ADDR *bufAddrList, uint32_t *segLenList, u_int pktLen, u_int hdrLen, HAL_PKT_TYPE type, u_int keyIx, HAL_CIPHER cipher, uint8_t delims, HAL_BOOL firstSeg, HAL_BOOL lastSeg, HAL_BOOL lastAggr); extern HAL_BOOL ar5416SetupFirstTxDesc(struct ath_hal *ah, struct ath_desc *ds, u_int aggrLen, u_int flags, u_int txPower, u_int txRate0, u_int txTries0, u_int antMode, u_int rtsctsRate, u_int rtsctsDuration); extern HAL_BOOL ar5416SetupLastTxDesc(struct ath_hal *ah, struct ath_desc *ds, const struct ath_desc *ds0); extern HAL_BOOL ar5416SetGlobalTxTimeout(struct ath_hal *ah, u_int tu); extern u_int ar5416GetGlobalTxTimeout(struct ath_hal *ah); extern void ar5416Set11nRateScenario(struct ath_hal *ah, struct ath_desc *ds, u_int durUpdateEn, u_int rtsctsRate, HAL_11N_RATE_SERIES series[], u_int nseries, u_int flags); extern void ar5416Set11nAggrFirst(struct ath_hal *ah, struct ath_desc *ds, u_int aggrLen, u_int numDelims); extern void ar5416Set11nAggrMiddle(struct ath_hal *ah, struct ath_desc *ds, u_int numDelims); extern void ar5416Set11nAggrLast(struct ath_hal *ah, struct ath_desc *ds); extern void ar5416Clr11nAggr(struct ath_hal *ah, struct ath_desc *ds); extern void ar5416Set11nVirtualMoreFrag(struct ath_hal *ah, struct ath_desc *ds, u_int vmf); extern void ar5416Set11nBurstDuration(struct ath_hal *ah, struct ath_desc *ds, u_int burstDuration); extern const HAL_RATE_TABLE *ar5416GetRateTable(struct ath_hal *, u_int mode); #endif /* _ATH_AR5416_H_ */