Index: head/sys/mips/conf/ONIONOMEGA.hints
===================================================================
--- head/sys/mips/conf/ONIONOMEGA.hints	(revision 313473)
+++ head/sys/mips/conf/ONIONOMEGA.hints	(revision 313474)
@@ -1,125 +1,132 @@
 #
 # This file adds to the values in AR933X_BASE.hints.
 #
 # $FreeBSD$
 
 # mdiobus on arge1
 hint.argemdio.0.at="nexus0"
 hint.argemdio.0.maddr=0x1a000000
 hint.argemdio.0.msize=0x1000
 hint.argemdio.0.order=0
 
 # Embedded Atheros Switch
 hint.arswitch.0.at="mdio0"
 
 # XXX this should really say it's an AR933x switch, as there
 # are some vlan specific differences here!
 hint.arswitch.0.is_7240=1
 hint.arswitch.0.numphys=4
 hint.arswitch.0.phy4cpu=1	# phy 4 is a "CPU" separate PHY
 hint.arswitch.0.is_rgmii=0
 hint.arswitch.0.is_gmii=1	# arge1 <-> switch PHY is GMII
 
 # arge0 - MII, autoneg, phy(4)
 hint.arge.0.phymask=0x10	# PHY4
 hint.arge.0.mdio=mdioproxy1	# .. off of the switch mdiobus
 hint.arge.0.eeprommac=0x1fff0000
 
 # arge1 - GMII, 1000/full
 hint.arge.1.phymask=0x0		# No directly mapped PHYs
 hint.arge.1.media=1000
 hint.arge.1.fduplex=1
 hint.arge.1.eeprommac=0x1fff0006
 
 # ath0
 hint.ath.0.eepromaddr=0x1fff0000
 hint.ath.0.eepromsize=16384
 
 # 16MB flash layout:
 # [    0.510000] 5 tp-link partitions found on MTD device spi0.0
 # [    0.510000] Creating 5 MTD partitions on "spi0.0":
 # [    0.520000] 0x000000000000-0x000000020000 : "u-boot"
 # [    0.520000] 0x000000020000-0x000000136468 : "kernel"
 # [    0.530000] 0x000000136468-0x000000ff0000 : "rootfs"
 # [    0.530000] mtd: device 2 (rootfs) set to be root filesystem
 # [    0.540000] 1 squashfs-split partitions found on MTD device rootfs
 # [    0.540000] 0x000000730000-0x000000fe0000 : "rootfs_data"
 # [    0.540000] 0x000000fe0000-0x000000ff0000 : "nvram"
 # [    0.550000] 0x000000ff0000-0x000001000000 : "art"
 # [    0.560000] 0x000000020000-0x000000fe0000 : "firmware"
 
 # 64KiB uboot
 hint.map.0.at="flash/spi0"
 hint.map.0.start=0x00000000
 hint.map.0.end=0x00010000
 hint.map.0.name="u-boot"
 hint.map.0.readonly=1
 
 # 64KiB uboot
 hint.map.1.at="flash/spi0"
 hint.map.1.start=0x00010000
 hint.map.1.end=0x00020000
 hint.map.1.name="uboot-env"
 hint.map.1.readonly=1
 
 # kernel
 hint.map.2.at="flash/spi0"
 hint.map.2.start=0x00020000
 hint.map.2.end="search:0x00020000:0x10000:.!/bin/sh"
 hint.map.2.name="kernel"
 hint.map.2.readonly=1
 
 # rootfs ulzma
 hint.map.3.at="flash/spi0"
 hint.map.3.start="search:0x00020000:0x10000:.!/bin/sh"
 hint.map.3.end=0x00fe0000
 hint.map.3.name="rootfs"
 hint.map.3.readonly=1
 
 # 64KiB cfg
 hint.map.4.at="flash/spi0"
 hint.map.4.start=0x00fe0000
 hint.map.4.end=0x00ff0000
 hint.map.4.name="cfg"
 hint.map.4.readonly=0
 
 # all firmware 16000KiB
 hint.map.5.at="flash/spi0"
 hint.map.5.start=0x00020000
 hint.map.5.end=0x00ff0000
 hint.map.5.name="firmware"
 hint.map.5.readonly=0
 
 # 64KiB ART
 hint.map.6.at="flash/spi0"
 hint.map.6.start=0x00ff0000
 hint.map.6.end=0x01000000
 hint.map.6.name="ART"
 hint.map.6.readonly=1
 
 # GPIO
 hint.gpio.0.pinmask=0x0c8ff1c3
 
 hint.gpioled.0.at="gpiobus0"
 hint.gpioled.0.pins=0x08000000
 hint.gpioled.0.name="board"
 hint.gpioled.0.invert=0
 
 #Red
 hint.gpioled.1.at="gpiobus0"
 hint.gpioled.1.pins=0x00020000
 hint.gpioled.1.name="red"
 hint.gpioled.1.invert=0
 
 #Green
 hint.gpioled.2.at="gpiobus0"
 hint.gpioled.2.pins=0x00010000
 hint.gpioled.2.name="green"
 hint.gpioled.2.invert=0
 
 #Blue
 hint.gpioled.3.at="gpiobus0"
 hint.gpioled.3.pins=0x00008000
 hint.gpioled.3.name="blue"
 hint.gpioled.3.invert=0
 
+# I2C
+# 0x20 - 0x27 = Relay Controllers (0x27 is default)
+# 0x5a = PWM/Servo Controller
+hint.gpioiic.0.at="gpiobus0"
+hint.gpioiic.0.pins=0x300000 # pins 20 and 21
+hint.gpioiic.0.scl=0 # pin 20
+hint.gpioiic.0.sda=1 # pin 21