Index: stable/10/sys/amd64/amd64/mp_machdep.c =================================================================== --- stable/10/sys/amd64/amd64/mp_machdep.c (revision 281559) +++ stable/10/sys/amd64/amd64/mp_machdep.c (revision 281560) @@ -1,1718 +1,1736 @@ /*- * Copyright (c) 1996, by Steve Passe * Copyright (c) 2003, by Peter Wemm * All rights reserved. * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * 1. Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * 2. The name of the developer may NOT be used to endorse or promote products * derived from this software without specific prior written permission. * * THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE * ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF * SUCH DAMAGE. */ #include __FBSDID("$FreeBSD$"); #include "opt_cpu.h" #include "opt_ddb.h" #include "opt_kstack_pages.h" #include "opt_sched.h" #include "opt_smp.h" #include #include #include #include #ifdef GPROF #include #endif #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #define WARMBOOT_TARGET 0 #define WARMBOOT_OFF (KERNBASE + 0x0467) #define WARMBOOT_SEG (KERNBASE + 0x0469) #define CMOS_REG (0x70) #define CMOS_DATA (0x71) #define BIOS_RESET (0x0f) #define BIOS_WARM (0x0a) /* lock region used by kernel profiling */ int mcount_lock; int mp_naps; /* # of Applications processors */ int boot_cpu_id = -1; /* designated BSP */ extern struct pcpu __pcpu[]; /* AP uses this during bootstrap. Do not staticize. */ char *bootSTK; static int bootAP; /* Free these after use */ void *bootstacks[MAXCPU]; /* Temporary variables for init_secondary() */ char *doublefault_stack; char *nmi_stack; void *dpcpu; struct pcb stoppcbs[MAXCPU]; struct susppcb **susppcbs; /* Variables needed for SMP tlb shootdown. */ vm_offset_t smp_tlb_addr2; struct invpcid_descr smp_tlb_invpcid; volatile int smp_tlb_wait; uint64_t pcid_cr3; pmap_t smp_tlb_pmap; extern int invpcid_works; #ifdef COUNT_IPIS /* Interrupt counts. */ static u_long *ipi_preempt_counts[MAXCPU]; static u_long *ipi_ast_counts[MAXCPU]; u_long *ipi_invltlb_counts[MAXCPU]; u_long *ipi_invlrng_counts[MAXCPU]; u_long *ipi_invlpg_counts[MAXCPU]; u_long *ipi_invlcache_counts[MAXCPU]; u_long *ipi_rendezvous_counts[MAXCPU]; static u_long *ipi_hardclock_counts[MAXCPU]; #endif /* Default cpu_ops implementation. */ struct cpu_ops cpu_ops = { .ipi_vectored = lapic_ipi_vectored }; extern inthand_t IDTVEC(fast_syscall), IDTVEC(fast_syscall32); extern int pmap_pcid_enabled; /* * Local data and functions. */ static volatile cpuset_t ipi_nmi_pending; /* used to hold the AP's until we are ready to release them */ static struct mtx ap_boot_mtx; /* Set to 1 once we're ready to let the APs out of the pen. */ static volatile int aps_ready = 0; /* * Store data from cpu_add() until later in the boot when we actually setup * the APs. */ struct cpu_info { int cpu_present:1; int cpu_bsp:1; int cpu_disabled:1; int cpu_hyperthread:1; } static cpu_info[MAX_APIC_ID + 1]; int cpu_apic_ids[MAXCPU]; int apic_cpuids[MAX_APIC_ID + 1]; /* Holds pending bitmap based IPIs per CPU */ volatile u_int cpu_ipi_pending[MAXCPU]; static u_int boot_address; static int cpu_logical; /* logical cpus per core */ static int cpu_cores; /* cores per package */ static void assign_cpu_ids(void); static void set_interrupt_apic_ids(void); static int start_all_aps(void); static int start_ap(int apic_id); static void release_aps(void *dummy); static u_int hyperthreading_cpus; /* logical cpus sharing L1 cache */ static int hyperthreading_allowed = 1; static u_int bootMP_size; static void mem_range_AP_init(void) { if (mem_range_softc.mr_op && mem_range_softc.mr_op->initAP) mem_range_softc.mr_op->initAP(&mem_range_softc); } static void topo_probe_amd(void) { int core_id_bits; int id; /* AMD processors do not support HTT. */ cpu_logical = 1; if ((amd_feature2 & AMDID2_CMP) == 0) { cpu_cores = 1; return; } core_id_bits = (cpu_procinfo2 & AMDID_COREID_SIZE) >> AMDID_COREID_SIZE_SHIFT; if (core_id_bits == 0) { cpu_cores = (cpu_procinfo2 & AMDID_CMP_CORES) + 1; return; } /* Fam 10h and newer should get here. */ for (id = 0; id <= MAX_APIC_ID; id++) { /* Check logical CPU availability. */ if (!cpu_info[id].cpu_present || cpu_info[id].cpu_disabled) continue; /* Check if logical CPU has the same package ID. */ if ((id >> core_id_bits) != (boot_cpu_id >> core_id_bits)) continue; cpu_cores++; } } /* * Round up to the next power of two, if necessary, and then * take log2. * Returns -1 if argument is zero. */ static __inline int mask_width(u_int x) { return (fls(x << (1 - powerof2(x))) - 1); } static void topo_probe_0x4(void) { u_int p[4]; int pkg_id_bits; int core_id_bits; int max_cores; int max_logical; int id; /* Both zero and one here mean one logical processor per package. */ max_logical = (cpu_feature & CPUID_HTT) != 0 ? (cpu_procinfo & CPUID_HTT_CORES) >> 16 : 1; if (max_logical <= 1) return; /* * Because of uniformity assumption we examine only * those logical processors that belong to the same * package as BSP. Further, we count number of * logical processors that belong to the same core * as BSP thus deducing number of threads per core. */ if (cpu_high >= 0x4) { cpuid_count(0x04, 0, p); max_cores = ((p[0] >> 26) & 0x3f) + 1; } else max_cores = 1; core_id_bits = mask_width(max_logical/max_cores); if (core_id_bits < 0) return; pkg_id_bits = core_id_bits + mask_width(max_cores); for (id = 0; id <= MAX_APIC_ID; id++) { /* Check logical CPU availability. */ if (!cpu_info[id].cpu_present || cpu_info[id].cpu_disabled) continue; /* Check if logical CPU has the same package ID. */ if ((id >> pkg_id_bits) != (boot_cpu_id >> pkg_id_bits)) continue; cpu_cores++; /* Check if logical CPU has the same package and core IDs. */ if ((id >> core_id_bits) == (boot_cpu_id >> core_id_bits)) cpu_logical++; } KASSERT(cpu_cores >= 1 && cpu_logical >= 1, ("topo_probe_0x4 couldn't find BSP")); cpu_cores /= cpu_logical; hyperthreading_cpus = cpu_logical; } static void topo_probe_0xb(void) { u_int p[4]; int bits; int cnt; int i; int logical; int type; int x; /* We only support three levels for now. */ for (i = 0; i < 3; i++) { cpuid_count(0x0b, i, p); /* Fall back if CPU leaf 11 doesn't really exist. */ if (i == 0 && p[1] == 0) { topo_probe_0x4(); return; } bits = p[0] & 0x1f; logical = p[1] &= 0xffff; type = (p[2] >> 8) & 0xff; if (type == 0 || logical == 0) break; /* * Because of uniformity assumption we examine only * those logical processors that belong to the same * package as BSP. */ for (cnt = 0, x = 0; x <= MAX_APIC_ID; x++) { if (!cpu_info[x].cpu_present || cpu_info[x].cpu_disabled) continue; if (x >> bits == boot_cpu_id >> bits) cnt++; } if (type == CPUID_TYPE_SMT) cpu_logical = cnt; else if (type == CPUID_TYPE_CORE) cpu_cores = cnt; } if (cpu_logical == 0) cpu_logical = 1; cpu_cores /= cpu_logical; } /* * Both topology discovery code and code that consumes topology * information assume top-down uniformity of the topology. * That is, all physical packages must be identical and each * core in a package must have the same number of threads. * Topology information is queried only on BSP, on which this * code runs and for which it can query CPUID information. * Then topology is extrapolated on all packages using the * uniformity assumption. */ static void topo_probe(void) { static int cpu_topo_probed = 0; if (cpu_topo_probed) return; CPU_ZERO(&logical_cpus_mask); if (mp_ncpus <= 1) cpu_cores = cpu_logical = 1; else if (cpu_vendor_id == CPU_VENDOR_AMD) topo_probe_amd(); else if (cpu_vendor_id == CPU_VENDOR_INTEL) { /* * See Intel(R) 64 Architecture Processor * Topology Enumeration article for details. * * Note that 0x1 <= cpu_high < 4 case should be * compatible with topo_probe_0x4() logic when * CPUID.1:EBX[23:16] > 0 (cpu_cores will be 1) * or it should trigger the fallback otherwise. */ if (cpu_high >= 0xb) topo_probe_0xb(); else if (cpu_high >= 0x1) topo_probe_0x4(); } /* * Fallback: assume each logical CPU is in separate * physical package. That is, no multi-core, no SMT. */ if (cpu_cores == 0 || cpu_logical == 0) cpu_cores = cpu_logical = 1; cpu_topo_probed = 1; } struct cpu_group * cpu_topo(void) { int cg_flags; /* * Determine whether any threading flags are * necessry. */ topo_probe(); if (cpu_logical > 1 && hyperthreading_cpus) cg_flags = CG_FLAG_HTT; else if (cpu_logical > 1) cg_flags = CG_FLAG_SMT; else cg_flags = 0; if (mp_ncpus % (cpu_cores * cpu_logical) != 0) { printf("WARNING: Non-uniform processors.\n"); printf("WARNING: Using suboptimal topology.\n"); return (smp_topo_none()); } /* * No multi-core or hyper-threaded. */ if (cpu_logical * cpu_cores == 1) return (smp_topo_none()); /* * Only HTT no multi-core. */ if (cpu_logical > 1 && cpu_cores == 1) return (smp_topo_1level(CG_SHARE_L1, cpu_logical, cg_flags)); /* * Only multi-core no HTT. */ if (cpu_cores > 1 && cpu_logical == 1) return (smp_topo_1level(CG_SHARE_L2, cpu_cores, cg_flags)); /* * Both HTT and multi-core. */ return (smp_topo_2level(CG_SHARE_L2, cpu_cores, CG_SHARE_L1, cpu_logical, cg_flags)); } /* * Calculate usable address in base memory for AP trampoline code. */ u_int mp_bootaddress(u_int basemem) { bootMP_size = mptramp_end - mptramp_start; boot_address = trunc_page(basemem * 1024); /* round down to 4k boundary */ if (((basemem * 1024) - boot_address) < bootMP_size) boot_address -= PAGE_SIZE; /* not enough, lower by 4k */ /* 3 levels of page table pages */ mptramp_pagetables = boot_address - (PAGE_SIZE * 3); return mptramp_pagetables; } void cpu_add(u_int apic_id, char boot_cpu) { if (apic_id > MAX_APIC_ID) { panic("SMP: APIC ID %d too high", apic_id); return; } KASSERT(cpu_info[apic_id].cpu_present == 0, ("CPU %d added twice", apic_id)); cpu_info[apic_id].cpu_present = 1; if (boot_cpu) { KASSERT(boot_cpu_id == -1, ("CPU %d claims to be BSP, but CPU %d already is", apic_id, boot_cpu_id)); boot_cpu_id = apic_id; cpu_info[apic_id].cpu_bsp = 1; } if (mp_ncpus < MAXCPU) { mp_ncpus++; mp_maxid = mp_ncpus - 1; } if (bootverbose) printf("SMP: Added CPU %d (%s)\n", apic_id, boot_cpu ? "BSP" : "AP"); } void cpu_mp_setmaxid(void) { /* * mp_maxid should be already set by calls to cpu_add(). * Just sanity check its value here. */ if (mp_ncpus == 0) KASSERT(mp_maxid == 0, ("%s: mp_ncpus is zero, but mp_maxid is not", __func__)); else if (mp_ncpus == 1) mp_maxid = 0; else KASSERT(mp_maxid >= mp_ncpus - 1, ("%s: counters out of sync: max %d, count %d", __func__, mp_maxid, mp_ncpus)); } int cpu_mp_probe(void) { /* * Always record BSP in CPU map so that the mbuf init code works * correctly. */ CPU_SETOF(0, &all_cpus); if (mp_ncpus == 0) { /* * No CPUs were found, so this must be a UP system. Setup * the variables to represent a system with a single CPU * with an id of 0. */ mp_ncpus = 1; return (0); } /* At least one CPU was found. */ if (mp_ncpus == 1) { /* * One CPU was found, so this must be a UP system with * an I/O APIC. */ mp_maxid = 0; return (0); } /* At least two CPUs were found. */ return (1); } /* * Initialize the IPI handlers and start up the AP's. */ void cpu_mp_start(void) { int i; /* Initialize the logical ID to APIC ID table. */ for (i = 0; i < MAXCPU; i++) { cpu_apic_ids[i] = -1; cpu_ipi_pending[i] = 0; } /* Install an inter-CPU IPI for TLB invalidation */ if (pmap_pcid_enabled) { setidt(IPI_INVLTLB, IDTVEC(invltlb_pcid), SDT_SYSIGT, SEL_KPL, 0); setidt(IPI_INVLPG, IDTVEC(invlpg_pcid), SDT_SYSIGT, SEL_KPL, 0); } else { setidt(IPI_INVLTLB, IDTVEC(invltlb), SDT_SYSIGT, SEL_KPL, 0); setidt(IPI_INVLPG, IDTVEC(invlpg), SDT_SYSIGT, SEL_KPL, 0); } setidt(IPI_INVLRNG, IDTVEC(invlrng), SDT_SYSIGT, SEL_KPL, 0); /* Install an inter-CPU IPI for cache invalidation. */ setidt(IPI_INVLCACHE, IDTVEC(invlcache), SDT_SYSIGT, SEL_KPL, 0); /* Install an inter-CPU IPI for all-CPU rendezvous */ setidt(IPI_RENDEZVOUS, IDTVEC(rendezvous), SDT_SYSIGT, SEL_KPL, 0); /* Install generic inter-CPU IPI handler */ setidt(IPI_BITMAP_VECTOR, IDTVEC(ipi_intr_bitmap_handler), SDT_SYSIGT, SEL_KPL, 0); /* Install an inter-CPU IPI for CPU stop/restart */ setidt(IPI_STOP, IDTVEC(cpustop), SDT_SYSIGT, SEL_KPL, 0); /* Install an inter-CPU IPI for CPU suspend/resume */ setidt(IPI_SUSPEND, IDTVEC(cpususpend), SDT_SYSIGT, SEL_KPL, 0); /* Set boot_cpu_id if needed. */ if (boot_cpu_id == -1) { boot_cpu_id = PCPU_GET(apic_id); cpu_info[boot_cpu_id].cpu_bsp = 1; } else KASSERT(boot_cpu_id == PCPU_GET(apic_id), ("BSP's APIC ID doesn't match boot_cpu_id")); /* Probe logical/physical core configuration. */ topo_probe(); assign_cpu_ids(); /* Start each Application Processor */ start_all_aps(); set_interrupt_apic_ids(); } /* * Print various information about the SMP system hardware and setup. */ void cpu_mp_announce(void) { const char *hyperthread; int i; printf("FreeBSD/SMP: %d package(s) x %d core(s)", mp_ncpus / (cpu_cores * cpu_logical), cpu_cores); if (hyperthreading_cpus > 1) printf(" x %d HTT threads", cpu_logical); else if (cpu_logical > 1) printf(" x %d SMT threads", cpu_logical); printf("\n"); /* List active CPUs first. */ printf(" cpu0 (BSP): APIC ID: %2d\n", boot_cpu_id); for (i = 1; i < mp_ncpus; i++) { if (cpu_info[cpu_apic_ids[i]].cpu_hyperthread) hyperthread = "/HT"; else hyperthread = ""; printf(" cpu%d (AP%s): APIC ID: %2d\n", i, hyperthread, cpu_apic_ids[i]); } /* List disabled CPUs last. */ for (i = 0; i <= MAX_APIC_ID; i++) { if (!cpu_info[i].cpu_present || !cpu_info[i].cpu_disabled) continue; if (cpu_info[i].cpu_hyperthread) hyperthread = "/HT"; else hyperthread = ""; printf(" cpu (AP%s): APIC ID: %2d (disabled)\n", hyperthread, i); } } /* * AP CPU's call this to initialize themselves. */ void init_secondary(void) { struct pcpu *pc; struct nmi_pcpu *np; u_int64_t msr, cr0; u_int cpuid; int cpu, gsel_tss, x; struct region_descriptor ap_gdt; /* Set by the startup code for us to use */ cpu = bootAP; /* Init tss */ common_tss[cpu] = common_tss[0]; common_tss[cpu].tss_rsp0 = 0; /* not used until after switch */ common_tss[cpu].tss_iobase = sizeof(struct amd64tss) + IOPAGES * PAGE_SIZE; common_tss[cpu].tss_ist1 = (long)&doublefault_stack[PAGE_SIZE]; /* The NMI stack runs on IST2. */ np = ((struct nmi_pcpu *) &nmi_stack[PAGE_SIZE]) - 1; common_tss[cpu].tss_ist2 = (long) np; /* Prepare private GDT */ gdt_segs[GPROC0_SEL].ssd_base = (long) &common_tss[cpu]; for (x = 0; x < NGDT; x++) { if (x != GPROC0_SEL && x != (GPROC0_SEL + 1) && x != GUSERLDT_SEL && x != (GUSERLDT_SEL + 1)) ssdtosd(&gdt_segs[x], &gdt[NGDT * cpu + x]); } ssdtosyssd(&gdt_segs[GPROC0_SEL], (struct system_segment_descriptor *)&gdt[NGDT * cpu + GPROC0_SEL]); ap_gdt.rd_limit = NGDT * sizeof(gdt[0]) - 1; ap_gdt.rd_base = (long) &gdt[NGDT * cpu]; lgdt(&ap_gdt); /* does magic intra-segment return */ /* Get per-cpu data */ pc = &__pcpu[cpu]; /* prime data page for it to use */ pcpu_init(pc, cpu, sizeof(struct pcpu)); dpcpu_init(dpcpu, cpu); pc->pc_apic_id = cpu_apic_ids[cpu]; pc->pc_prvspace = pc; pc->pc_curthread = 0; pc->pc_tssp = &common_tss[cpu]; pc->pc_commontssp = &common_tss[cpu]; pc->pc_rsp0 = 0; pc->pc_tss = (struct system_segment_descriptor *)&gdt[NGDT * cpu + GPROC0_SEL]; pc->pc_fs32p = &gdt[NGDT * cpu + GUFS32_SEL]; pc->pc_gs32p = &gdt[NGDT * cpu + GUGS32_SEL]; pc->pc_ldt = (struct system_segment_descriptor *)&gdt[NGDT * cpu + GUSERLDT_SEL]; /* Save the per-cpu pointer for use by the NMI handler. */ np->np_pcpu = (register_t) pc; wrmsr(MSR_FSBASE, 0); /* User value */ wrmsr(MSR_GSBASE, (u_int64_t)pc); wrmsr(MSR_KGSBASE, (u_int64_t)pc); /* XXX User value while we're in the kernel */ lidt(&r_idt); gsel_tss = GSEL(GPROC0_SEL, SEL_KPL); ltr(gsel_tss); /* * Set to a known state: * Set by mpboot.s: CR0_PG, CR0_PE * Set by cpu_setregs: CR0_NE, CR0_MP, CR0_TS, CR0_WP, CR0_AM */ cr0 = rcr0(); cr0 &= ~(CR0_CD | CR0_NW | CR0_EM); load_cr0(cr0); /* Set up the fast syscall stuff */ msr = rdmsr(MSR_EFER) | EFER_SCE; wrmsr(MSR_EFER, msr); wrmsr(MSR_LSTAR, (u_int64_t)IDTVEC(fast_syscall)); wrmsr(MSR_CSTAR, (u_int64_t)IDTVEC(fast_syscall32)); msr = ((u_int64_t)GSEL(GCODE_SEL, SEL_KPL) << 32) | ((u_int64_t)GSEL(GUCODE32_SEL, SEL_UPL) << 48); wrmsr(MSR_STAR, msr); wrmsr(MSR_SF_MASK, PSL_NT|PSL_T|PSL_I|PSL_C|PSL_D); /* Disable local APIC just to be sure. */ lapic_disable(); /* signal our startup to the BSP. */ mp_naps++; /* Spin until the BSP releases the AP's. */ while (!aps_ready) ia32_pause(); /* Initialize the PAT MSR. */ pmap_init_pat(); /* set up CPU registers and state */ cpu_setregs(); /* set up SSE/NX */ initializecpu(); /* set up FPU state on the AP */ fpuinit(); if (cpu_ops.cpu_init) cpu_ops.cpu_init(); /* A quick check from sanity claus */ cpuid = PCPU_GET(cpuid); if (PCPU_GET(apic_id) != lapic_id()) { printf("SMP: cpuid = %d\n", cpuid); printf("SMP: actual apic_id = %d\n", lapic_id()); printf("SMP: correct apic_id = %d\n", PCPU_GET(apic_id)); panic("cpuid mismatch! boom!!"); } /* Initialize curthread. */ KASSERT(PCPU_GET(idlethread) != NULL, ("no idle thread")); PCPU_SET(curthread, PCPU_GET(idlethread)); mca_init(); mtx_lock_spin(&ap_boot_mtx); /* Init local apic for irq's */ lapic_setup(1); /* Set memory range attributes for this CPU to match the BSP */ mem_range_AP_init(); smp_cpus++; CTR1(KTR_SMP, "SMP: AP CPU #%d Launched", cpuid); printf("SMP: AP CPU #%d Launched!\n", cpuid); /* Determine if we are a logical CPU. */ /* XXX Calculation depends on cpu_logical being a power of 2, e.g. 2 */ if (cpu_logical > 1 && PCPU_GET(apic_id) % cpu_logical != 0) CPU_SET(cpuid, &logical_cpus_mask); if (bootverbose) lapic_dump("AP"); if (smp_cpus == mp_ncpus) { /* enable IPI's, tlb shootdown, freezes etc */ atomic_store_rel_int(&smp_started, 1); } /* * Enable global pages TLB extension * This also implicitly flushes the TLB */ load_cr4(rcr4() | CR4_PGE); if (pmap_pcid_enabled) load_cr4(rcr4() | CR4_PCIDE); load_ds(_udatasel); load_es(_udatasel); load_fs(_ufssel); mtx_unlock_spin(&ap_boot_mtx); /* Wait until all the AP's are up. */ while (smp_started == 0) ia32_pause(); /* Start per-CPU event timers. */ cpu_initclocks_ap(); sched_throw(NULL); panic("scheduler returned us to %s", __func__); /* NOTREACHED */ } /******************************************************************* * local functions and data */ /* * We tell the I/O APIC code about all the CPUs we want to receive * interrupts. If we don't want certain CPUs to receive IRQs we * can simply not tell the I/O APIC code about them in this function. * We also do not tell it about the BSP since it tells itself about * the BSP internally to work with UP kernels and on UP machines. */ static void set_interrupt_apic_ids(void) { u_int i, apic_id; for (i = 0; i < MAXCPU; i++) { apic_id = cpu_apic_ids[i]; if (apic_id == -1) continue; if (cpu_info[apic_id].cpu_bsp) continue; if (cpu_info[apic_id].cpu_disabled) continue; /* Don't let hyperthreads service interrupts. */ if (hyperthreading_cpus > 1 && apic_id % hyperthreading_cpus != 0) continue; intr_add_cpu(i); } } /* * Assign logical CPU IDs to local APICs. */ static void assign_cpu_ids(void) { u_int i; TUNABLE_INT_FETCH("machdep.hyperthreading_allowed", &hyperthreading_allowed); /* Check for explicitly disabled CPUs. */ for (i = 0; i <= MAX_APIC_ID; i++) { if (!cpu_info[i].cpu_present || cpu_info[i].cpu_bsp) continue; if (hyperthreading_cpus > 1 && i % hyperthreading_cpus != 0) { cpu_info[i].cpu_hyperthread = 1; /* * Don't use HT CPU if it has been disabled by a * tunable. */ if (hyperthreading_allowed == 0) { cpu_info[i].cpu_disabled = 1; continue; } } /* Don't use this CPU if it has been disabled by a tunable. */ if (resource_disabled("lapic", i)) { cpu_info[i].cpu_disabled = 1; continue; } } if (hyperthreading_allowed == 0 && hyperthreading_cpus > 1) { hyperthreading_cpus = 0; cpu_logical = 1; } /* * Assign CPU IDs to local APIC IDs and disable any CPUs * beyond MAXCPU. CPU 0 is always assigned to the BSP. * * To minimize confusion for userland, we attempt to number * CPUs such that all threads and cores in a package are * grouped together. For now we assume that the BSP is always * the first thread in a package and just start adding APs * starting with the BSP's APIC ID. */ mp_ncpus = 1; cpu_apic_ids[0] = boot_cpu_id; apic_cpuids[boot_cpu_id] = 0; for (i = boot_cpu_id + 1; i != boot_cpu_id; i == MAX_APIC_ID ? i = 0 : i++) { if (!cpu_info[i].cpu_present || cpu_info[i].cpu_bsp || cpu_info[i].cpu_disabled) continue; if (mp_ncpus < MAXCPU) { cpu_apic_ids[mp_ncpus] = i; apic_cpuids[i] = mp_ncpus; mp_ncpus++; } else cpu_info[i].cpu_disabled = 1; } KASSERT(mp_maxid >= mp_ncpus - 1, ("%s: counters out of sync: max %d, count %d", __func__, mp_maxid, mp_ncpus)); } /* * start each AP in our list */ static int start_all_aps(void) { vm_offset_t va = boot_address + KERNBASE; u_int64_t *pt4, *pt3, *pt2; u_int32_t mpbioswarmvec; int apic_id, cpu, i; u_char mpbiosreason; mtx_init(&ap_boot_mtx, "ap boot", NULL, MTX_SPIN); /* install the AP 1st level boot code */ pmap_kenter(va, boot_address); pmap_invalidate_page(kernel_pmap, va); bcopy(mptramp_start, (void *)va, bootMP_size); /* Locate the page tables, they'll be below the trampoline */ pt4 = (u_int64_t *)(uintptr_t)(mptramp_pagetables + KERNBASE); pt3 = pt4 + (PAGE_SIZE) / sizeof(u_int64_t); pt2 = pt3 + (PAGE_SIZE) / sizeof(u_int64_t); /* Create the initial 1GB replicated page tables */ for (i = 0; i < 512; i++) { /* Each slot of the level 4 pages points to the same level 3 page */ pt4[i] = (u_int64_t)(uintptr_t)(mptramp_pagetables + PAGE_SIZE); pt4[i] |= PG_V | PG_RW | PG_U; /* Each slot of the level 3 pages points to the same level 2 page */ pt3[i] = (u_int64_t)(uintptr_t)(mptramp_pagetables + (2 * PAGE_SIZE)); pt3[i] |= PG_V | PG_RW | PG_U; /* The level 2 page slots are mapped with 2MB pages for 1GB. */ pt2[i] = i * (2 * 1024 * 1024); pt2[i] |= PG_V | PG_RW | PG_PS | PG_U; } /* save the current value of the warm-start vector */ mpbioswarmvec = *((u_int32_t *) WARMBOOT_OFF); outb(CMOS_REG, BIOS_RESET); mpbiosreason = inb(CMOS_DATA); /* setup a vector to our boot code */ *((volatile u_short *) WARMBOOT_OFF) = WARMBOOT_TARGET; *((volatile u_short *) WARMBOOT_SEG) = (boot_address >> 4); outb(CMOS_REG, BIOS_RESET); outb(CMOS_DATA, BIOS_WARM); /* 'warm-start' */ /* start each AP */ for (cpu = 1; cpu < mp_ncpus; cpu++) { apic_id = cpu_apic_ids[cpu]; /* allocate and set up an idle stack data page */ bootstacks[cpu] = (void *)kmem_malloc(kernel_arena, KSTACK_PAGES * PAGE_SIZE, M_WAITOK | M_ZERO); doublefault_stack = (char *)kmem_malloc(kernel_arena, PAGE_SIZE, M_WAITOK | M_ZERO); nmi_stack = (char *)kmem_malloc(kernel_arena, PAGE_SIZE, M_WAITOK | M_ZERO); dpcpu = (void *)kmem_malloc(kernel_arena, DPCPU_SIZE, M_WAITOK | M_ZERO); bootSTK = (char *)bootstacks[cpu] + KSTACK_PAGES * PAGE_SIZE - 8; bootAP = cpu; /* attempt to start the Application Processor */ if (!start_ap(apic_id)) { /* restore the warmstart vector */ *(u_int32_t *) WARMBOOT_OFF = mpbioswarmvec; panic("AP #%d (PHY# %d) failed!", cpu, apic_id); } CPU_SET(cpu, &all_cpus); /* record AP in CPU map */ } /* restore the warmstart vector */ *(u_int32_t *) WARMBOOT_OFF = mpbioswarmvec; outb(CMOS_REG, BIOS_RESET); outb(CMOS_DATA, mpbiosreason); /* number of APs actually started */ return mp_naps; } /* * This function starts the AP (application processor) identified * by the APIC ID 'physicalCpu'. It does quite a "song and dance" * to accomplish this. This is necessary because of the nuances * of the different hardware we might encounter. It isn't pretty, * but it seems to work. */ static int start_ap(int apic_id) { int vector, ms; int cpus; /* calculate the vector */ vector = (boot_address >> 12) & 0xff; /* used as a watchpoint to signal AP startup */ cpus = mp_naps; ipi_startup(apic_id, vector); /* Wait up to 5 seconds for it to start. */ for (ms = 0; ms < 5000; ms++) { if (mp_naps > cpus) return 1; /* return SUCCESS */ DELAY(1000); } return 0; /* return FAILURE */ } #ifdef COUNT_XINVLTLB_HITS u_int xhits_gbl[MAXCPU]; u_int xhits_pg[MAXCPU]; u_int xhits_rng[MAXCPU]; static SYSCTL_NODE(_debug, OID_AUTO, xhits, CTLFLAG_RW, 0, ""); SYSCTL_OPAQUE(_debug_xhits, OID_AUTO, global, CTLFLAG_RW, &xhits_gbl, sizeof(xhits_gbl), "IU", ""); SYSCTL_OPAQUE(_debug_xhits, OID_AUTO, page, CTLFLAG_RW, &xhits_pg, sizeof(xhits_pg), "IU", ""); SYSCTL_OPAQUE(_debug_xhits, OID_AUTO, range, CTLFLAG_RW, &xhits_rng, sizeof(xhits_rng), "IU", ""); u_int ipi_global; u_int ipi_page; u_int ipi_range; u_int ipi_range_size; SYSCTL_UINT(_debug_xhits, OID_AUTO, ipi_global, CTLFLAG_RW, &ipi_global, 0, ""); SYSCTL_UINT(_debug_xhits, OID_AUTO, ipi_page, CTLFLAG_RW, &ipi_page, 0, ""); SYSCTL_UINT(_debug_xhits, OID_AUTO, ipi_range, CTLFLAG_RW, &ipi_range, 0, ""); SYSCTL_UINT(_debug_xhits, OID_AUTO, ipi_range_size, CTLFLAG_RW, &ipi_range_size, 0, ""); u_int ipi_masked_global; u_int ipi_masked_page; u_int ipi_masked_range; u_int ipi_masked_range_size; SYSCTL_UINT(_debug_xhits, OID_AUTO, ipi_masked_global, CTLFLAG_RW, &ipi_masked_global, 0, ""); SYSCTL_UINT(_debug_xhits, OID_AUTO, ipi_masked_page, CTLFLAG_RW, &ipi_masked_page, 0, ""); SYSCTL_UINT(_debug_xhits, OID_AUTO, ipi_masked_range, CTLFLAG_RW, &ipi_masked_range, 0, ""); SYSCTL_UINT(_debug_xhits, OID_AUTO, ipi_masked_range_size, CTLFLAG_RW, &ipi_masked_range_size, 0, ""); #endif /* COUNT_XINVLTLB_HITS */ /* * Init and startup IPI. */ void ipi_startup(int apic_id, int vector) { /* + * This attempts to follow the algorithm described in the + * Intel Multiprocessor Specification v1.4 in section B.4. + * For each IPI, we allow the local APIC ~20us to deliver the + * IPI. If that times out, we panic. + */ + + /* * first we do an INIT IPI: this INIT IPI might be run, resetting * and running the target CPU. OR this INIT IPI might be latched (P5 * bug), CPU waiting for STARTUP IPI. OR this INIT IPI might be * ignored. */ - lapic_ipi_raw(APIC_DEST_DESTFLD | APIC_TRIGMOD_EDGE | + lapic_ipi_raw(APIC_DEST_DESTFLD | APIC_TRIGMOD_LEVEL | APIC_LEVEL_ASSERT | APIC_DESTMODE_PHY | APIC_DELMODE_INIT, apic_id); - lapic_ipi_wait(-1); + lapic_ipi_wait(100); + + /* Explicitly deassert the INIT IPI. */ + lapic_ipi_raw(APIC_DEST_DESTFLD | APIC_TRIGMOD_LEVEL | + APIC_LEVEL_DEASSERT | APIC_DESTMODE_PHY | APIC_DELMODE_INIT, + apic_id); + DELAY(10000); /* wait ~10mS */ /* * next we do a STARTUP IPI: the previous INIT IPI might still be * latched, (P5 bug) this 1st STARTUP would then terminate * immediately, and the previously started INIT IPI would continue. OR * the previous INIT IPI has already run. and this STARTUP IPI will * run. OR the previous INIT IPI was ignored. and this STARTUP IPI * will run. */ lapic_ipi_raw(APIC_DEST_DESTFLD | APIC_TRIGMOD_EDGE | - APIC_LEVEL_DEASSERT | APIC_DESTMODE_PHY | APIC_DELMODE_STARTUP | + APIC_LEVEL_ASSERT | APIC_DESTMODE_PHY | APIC_DELMODE_STARTUP | vector, apic_id); - lapic_ipi_wait(-1); + if (!lapic_ipi_wait(100)) + panic("Failed to deliver first STARTUP IPI to APIC %d", + apic_id); DELAY(200); /* wait ~200uS */ /* * finally we do a 2nd STARTUP IPI: this 2nd STARTUP IPI should run IF * the previous STARTUP IPI was cancelled by a latched INIT IPI. OR * this STARTUP IPI will be ignored, as only ONE STARTUP IPI is * recognized after hardware RESET or INIT IPI. */ lapic_ipi_raw(APIC_DEST_DESTFLD | APIC_TRIGMOD_EDGE | - APIC_LEVEL_DEASSERT | APIC_DESTMODE_PHY | APIC_DELMODE_STARTUP | + APIC_LEVEL_ASSERT | APIC_DESTMODE_PHY | APIC_DELMODE_STARTUP | vector, apic_id); - lapic_ipi_wait(-1); + if (!lapic_ipi_wait(100)) + panic("Failed to deliver second STARTUP IPI to APIC %d", + apic_id); + DELAY(200); /* wait ~200uS */ } /* * Send an IPI to specified CPU handling the bitmap logic. */ static void ipi_send_cpu(int cpu, u_int ipi) { u_int bitmap, old_pending, new_pending; KASSERT(cpu_apic_ids[cpu] != -1, ("IPI to non-existent CPU %d", cpu)); if (IPI_IS_BITMAPED(ipi)) { bitmap = 1 << ipi; ipi = IPI_BITMAP_VECTOR; do { old_pending = cpu_ipi_pending[cpu]; new_pending = old_pending | bitmap; } while (!atomic_cmpset_int(&cpu_ipi_pending[cpu], old_pending, new_pending)); if (old_pending) return; } cpu_ops.ipi_vectored(ipi, cpu_apic_ids[cpu]); } /* * Flush the TLB on all other CPU's */ static void smp_tlb_shootdown(u_int vector, pmap_t pmap, vm_offset_t addr1, vm_offset_t addr2) { u_int ncpu; ncpu = mp_ncpus - 1; /* does not shootdown self */ if (ncpu < 1) return; /* no other cpus */ if (!(read_rflags() & PSL_I)) panic("%s: interrupts disabled", __func__); mtx_lock_spin(&smp_ipi_mtx); smp_tlb_invpcid.addr = addr1; if (pmap == NULL) { smp_tlb_invpcid.pcid = 0; } else { smp_tlb_invpcid.pcid = pmap->pm_pcid; pcid_cr3 = pmap->pm_cr3; } smp_tlb_addr2 = addr2; smp_tlb_pmap = pmap; atomic_store_rel_int(&smp_tlb_wait, 0); ipi_all_but_self(vector); while (smp_tlb_wait < ncpu) ia32_pause(); mtx_unlock_spin(&smp_ipi_mtx); } static void smp_targeted_tlb_shootdown(cpuset_t mask, u_int vector, pmap_t pmap, vm_offset_t addr1, vm_offset_t addr2) { int cpu, ncpu, othercpus; othercpus = mp_ncpus - 1; if (CPU_ISFULLSET(&mask)) { if (othercpus < 1) return; } else { CPU_CLR(PCPU_GET(cpuid), &mask); if (CPU_EMPTY(&mask)) return; } if (!(read_rflags() & PSL_I)) panic("%s: interrupts disabled", __func__); mtx_lock_spin(&smp_ipi_mtx); smp_tlb_invpcid.addr = addr1; if (pmap == NULL) { smp_tlb_invpcid.pcid = 0; } else { smp_tlb_invpcid.pcid = pmap->pm_pcid; pcid_cr3 = pmap->pm_cr3; } smp_tlb_addr2 = addr2; smp_tlb_pmap = pmap; atomic_store_rel_int(&smp_tlb_wait, 0); if (CPU_ISFULLSET(&mask)) { ncpu = othercpus; ipi_all_but_self(vector); } else { ncpu = 0; while ((cpu = CPU_FFS(&mask)) != 0) { cpu--; CPU_CLR(cpu, &mask); CTR3(KTR_SMP, "%s: cpu: %d ipi: %x", __func__, cpu, vector); ipi_send_cpu(cpu, vector); ncpu++; } } while (smp_tlb_wait < ncpu) ia32_pause(); mtx_unlock_spin(&smp_ipi_mtx); } void smp_cache_flush(void) { if (smp_started) smp_tlb_shootdown(IPI_INVLCACHE, NULL, 0, 0); } void smp_invltlb(pmap_t pmap) { if (smp_started) { smp_tlb_shootdown(IPI_INVLTLB, pmap, 0, 0); #ifdef COUNT_XINVLTLB_HITS ipi_global++; #endif } } void smp_invlpg(pmap_t pmap, vm_offset_t addr) { if (smp_started) { smp_tlb_shootdown(IPI_INVLPG, pmap, addr, 0); #ifdef COUNT_XINVLTLB_HITS ipi_page++; #endif } } void smp_invlpg_range(pmap_t pmap, vm_offset_t addr1, vm_offset_t addr2) { if (smp_started) { smp_tlb_shootdown(IPI_INVLRNG, pmap, addr1, addr2); #ifdef COUNT_XINVLTLB_HITS ipi_range++; ipi_range_size += (addr2 - addr1) / PAGE_SIZE; #endif } } void smp_masked_invltlb(cpuset_t mask, pmap_t pmap) { if (smp_started) { smp_targeted_tlb_shootdown(mask, IPI_INVLTLB, pmap, 0, 0); #ifdef COUNT_XINVLTLB_HITS ipi_masked_global++; #endif } } void smp_masked_invlpg(cpuset_t mask, pmap_t pmap, vm_offset_t addr) { if (smp_started) { smp_targeted_tlb_shootdown(mask, IPI_INVLPG, pmap, addr, 0); #ifdef COUNT_XINVLTLB_HITS ipi_masked_page++; #endif } } void smp_masked_invlpg_range(cpuset_t mask, pmap_t pmap, vm_offset_t addr1, vm_offset_t addr2) { if (smp_started) { smp_targeted_tlb_shootdown(mask, IPI_INVLRNG, pmap, addr1, addr2); #ifdef COUNT_XINVLTLB_HITS ipi_masked_range++; ipi_masked_range_size += (addr2 - addr1) / PAGE_SIZE; #endif } } void ipi_bitmap_handler(struct trapframe frame) { struct trapframe *oldframe; struct thread *td; int cpu = PCPU_GET(cpuid); u_int ipi_bitmap; critical_enter(); td = curthread; td->td_intr_nesting_level++; oldframe = td->td_intr_frame; td->td_intr_frame = &frame; ipi_bitmap = atomic_readandclear_int(&cpu_ipi_pending[cpu]); if (ipi_bitmap & (1 << IPI_PREEMPT)) { #ifdef COUNT_IPIS (*ipi_preempt_counts[cpu])++; #endif sched_preempt(td); } if (ipi_bitmap & (1 << IPI_AST)) { #ifdef COUNT_IPIS (*ipi_ast_counts[cpu])++; #endif /* Nothing to do for AST */ } if (ipi_bitmap & (1 << IPI_HARDCLOCK)) { #ifdef COUNT_IPIS (*ipi_hardclock_counts[cpu])++; #endif hardclockintr(); } td->td_intr_frame = oldframe; td->td_intr_nesting_level--; critical_exit(); } /* * send an IPI to a set of cpus. */ void ipi_selected(cpuset_t cpus, u_int ipi) { int cpu; /* * IPI_STOP_HARD maps to a NMI and the trap handler needs a bit * of help in order to understand what is the source. * Set the mask of receiving CPUs for this purpose. */ if (ipi == IPI_STOP_HARD) CPU_OR_ATOMIC(&ipi_nmi_pending, &cpus); while ((cpu = CPU_FFS(&cpus)) != 0) { cpu--; CPU_CLR(cpu, &cpus); CTR3(KTR_SMP, "%s: cpu: %d ipi: %x", __func__, cpu, ipi); ipi_send_cpu(cpu, ipi); } } /* * send an IPI to a specific CPU. */ void ipi_cpu(int cpu, u_int ipi) { /* * IPI_STOP_HARD maps to a NMI and the trap handler needs a bit * of help in order to understand what is the source. * Set the mask of receiving CPUs for this purpose. */ if (ipi == IPI_STOP_HARD) CPU_SET_ATOMIC(cpu, &ipi_nmi_pending); CTR3(KTR_SMP, "%s: cpu: %d ipi: %x", __func__, cpu, ipi); ipi_send_cpu(cpu, ipi); } /* * send an IPI to all CPUs EXCEPT myself */ void ipi_all_but_self(u_int ipi) { cpuset_t other_cpus; other_cpus = all_cpus; CPU_CLR(PCPU_GET(cpuid), &other_cpus); if (IPI_IS_BITMAPED(ipi)) { ipi_selected(other_cpus, ipi); return; } /* * IPI_STOP_HARD maps to a NMI and the trap handler needs a bit * of help in order to understand what is the source. * Set the mask of receiving CPUs for this purpose. */ if (ipi == IPI_STOP_HARD) CPU_OR_ATOMIC(&ipi_nmi_pending, &other_cpus); CTR2(KTR_SMP, "%s: ipi: %x", __func__, ipi); cpu_ops.ipi_vectored(ipi, APIC_IPI_DEST_OTHERS); } int ipi_nmi_handler() { u_int cpuid; /* * As long as there is not a simple way to know about a NMI's * source, if the bitmask for the current CPU is present in * the global pending bitword an IPI_STOP_HARD has been issued * and should be handled. */ cpuid = PCPU_GET(cpuid); if (!CPU_ISSET(cpuid, &ipi_nmi_pending)) return (1); CPU_CLR_ATOMIC(cpuid, &ipi_nmi_pending); cpustop_handler(); return (0); } /* * Handle an IPI_STOP by saving our current context and spinning until we * are resumed. */ void cpustop_handler(void) { u_int cpu; cpu = PCPU_GET(cpuid); savectx(&stoppcbs[cpu]); /* Indicate that we are stopped */ CPU_SET_ATOMIC(cpu, &stopped_cpus); /* Wait for restart */ while (!CPU_ISSET(cpu, &started_cpus)) ia32_pause(); CPU_CLR_ATOMIC(cpu, &started_cpus); CPU_CLR_ATOMIC(cpu, &stopped_cpus); #ifdef DDB amd64_db_resume_dbreg(); #endif if (cpu == 0 && cpustop_restartfunc != NULL) { cpustop_restartfunc(); cpustop_restartfunc = NULL; } } /* * Handle an IPI_SUSPEND by saving our current context and spinning until we * are resumed. */ void cpususpend_handler(void) { u_int cpu; mtx_assert(&smp_ipi_mtx, MA_NOTOWNED); cpu = PCPU_GET(cpuid); if (savectx(&susppcbs[cpu]->sp_pcb)) { fpususpend(susppcbs[cpu]->sp_fpususpend); wbinvd(); CPU_SET_ATOMIC(cpu, &suspended_cpus); } else { fpuresume(susppcbs[cpu]->sp_fpususpend); pmap_init_pat(); initializecpu(); PCPU_SET(switchtime, 0); PCPU_SET(switchticks, ticks); /* Indicate that we are resumed */ CPU_CLR_ATOMIC(cpu, &suspended_cpus); } /* Wait for resume */ while (!CPU_ISSET(cpu, &started_cpus)) ia32_pause(); if (cpu_ops.cpu_resume) cpu_ops.cpu_resume(); if (vmm_resume_p) vmm_resume_p(); /* Resume MCA and local APIC */ mca_resume(); lapic_setup(0); CPU_CLR_ATOMIC(cpu, &started_cpus); /* Indicate that we are resumed */ CPU_CLR_ATOMIC(cpu, &suspended_cpus); } /* * Handlers for TLB related IPIs */ void invltlb_handler(void) { #ifdef COUNT_XINVLTLB_HITS xhits_gbl[PCPU_GET(cpuid)]++; #endif /* COUNT_XINVLTLB_HITS */ #ifdef COUNT_IPIS (*ipi_invltlb_counts[PCPU_GET(cpuid)])++; #endif /* COUNT_IPIS */ invltlb(); atomic_add_int(&smp_tlb_wait, 1); } void invltlb_pcid_handler(void) { uint64_t cr3; u_int cpuid; #ifdef COUNT_XINVLTLB_HITS xhits_gbl[PCPU_GET(cpuid)]++; #endif /* COUNT_XINVLTLB_HITS */ #ifdef COUNT_IPIS (*ipi_invltlb_counts[PCPU_GET(cpuid)])++; #endif /* COUNT_IPIS */ if (smp_tlb_invpcid.pcid != (uint64_t)-1 && smp_tlb_invpcid.pcid != 0) { if (invpcid_works) { invpcid(&smp_tlb_invpcid, INVPCID_CTX); } else { /* Otherwise reload %cr3 twice. */ cr3 = rcr3(); if (cr3 != pcid_cr3) { load_cr3(pcid_cr3); cr3 |= CR3_PCID_SAVE; } load_cr3(cr3); } } else { invltlb_globpcid(); } if (smp_tlb_pmap != NULL) { cpuid = PCPU_GET(cpuid); if (!CPU_ISSET(cpuid, &smp_tlb_pmap->pm_active)) CPU_CLR_ATOMIC(cpuid, &smp_tlb_pmap->pm_save); } atomic_add_int(&smp_tlb_wait, 1); } void invlpg_handler(void) { #ifdef COUNT_XINVLTLB_HITS xhits_pg[PCPU_GET(cpuid)]++; #endif /* COUNT_XINVLTLB_HITS */ #ifdef COUNT_IPIS (*ipi_invlpg_counts[PCPU_GET(cpuid)])++; #endif /* COUNT_IPIS */ invlpg(smp_tlb_invpcid.addr); atomic_add_int(&smp_tlb_wait, 1); } void invlpg_pcid_handler(void) { uint64_t cr3; #ifdef COUNT_XINVLTLB_HITS xhits_pg[PCPU_GET(cpuid)]++; #endif /* COUNT_XINVLTLB_HITS */ #ifdef COUNT_IPIS (*ipi_invlpg_counts[PCPU_GET(cpuid)])++; #endif /* COUNT_IPIS */ if (smp_tlb_invpcid.pcid == (uint64_t)-1) { invltlb_globpcid(); } else if (smp_tlb_invpcid.pcid == 0) { invlpg(smp_tlb_invpcid.addr); } else if (invpcid_works) { invpcid(&smp_tlb_invpcid, INVPCID_ADDR); } else { /* * PCID supported, but INVPCID is not. * Temporarily switch to the target address * space and do INVLPG. */ cr3 = rcr3(); if (cr3 != pcid_cr3) load_cr3(pcid_cr3 | CR3_PCID_SAVE); invlpg(smp_tlb_invpcid.addr); load_cr3(cr3 | CR3_PCID_SAVE); } atomic_add_int(&smp_tlb_wait, 1); } static inline void invlpg_range(vm_offset_t start, vm_offset_t end) { do { invlpg(start); start += PAGE_SIZE; } while (start < end); } void invlrng_handler(void) { struct invpcid_descr d; vm_offset_t addr; uint64_t cr3; u_int cpuid; #ifdef COUNT_XINVLTLB_HITS xhits_rng[PCPU_GET(cpuid)]++; #endif /* COUNT_XINVLTLB_HITS */ #ifdef COUNT_IPIS (*ipi_invlrng_counts[PCPU_GET(cpuid)])++; #endif /* COUNT_IPIS */ addr = smp_tlb_invpcid.addr; if (pmap_pcid_enabled) { if (smp_tlb_invpcid.pcid == 0) { /* * kernel pmap - use invlpg to invalidate * global mapping. */ invlpg_range(addr, smp_tlb_addr2); } else if (smp_tlb_invpcid.pcid == (uint64_t)-1) { invltlb_globpcid(); if (smp_tlb_pmap != NULL) { cpuid = PCPU_GET(cpuid); if (!CPU_ISSET(cpuid, &smp_tlb_pmap->pm_active)) CPU_CLR_ATOMIC(cpuid, &smp_tlb_pmap->pm_save); } } else if (invpcid_works) { d = smp_tlb_invpcid; do { invpcid(&d, INVPCID_ADDR); d.addr += PAGE_SIZE; } while (d.addr <= smp_tlb_addr2); } else { cr3 = rcr3(); if (cr3 != pcid_cr3) load_cr3(pcid_cr3 | CR3_PCID_SAVE); invlpg_range(addr, smp_tlb_addr2); load_cr3(cr3 | CR3_PCID_SAVE); } } else { invlpg_range(addr, smp_tlb_addr2); } atomic_add_int(&smp_tlb_wait, 1); } void invlcache_handler(void) { #ifdef COUNT_IPIS (*ipi_invlcache_counts[PCPU_GET(cpuid)])++; #endif /* COUNT_IPIS */ wbinvd(); atomic_add_int(&smp_tlb_wait, 1); } /* * This is called once the rest of the system is up and running and we're * ready to let the AP's out of the pen. */ static void release_aps(void *dummy __unused) { if (mp_ncpus == 1) return; atomic_store_rel_int(&aps_ready, 1); while (smp_started == 0) ia32_pause(); } SYSINIT(start_aps, SI_SUB_SMP, SI_ORDER_FIRST, release_aps, NULL); #ifdef COUNT_IPIS /* * Setup interrupt counters for IPI handlers. */ static void mp_ipi_intrcnt(void *dummy) { char buf[64]; int i; CPU_FOREACH(i) { snprintf(buf, sizeof(buf), "cpu%d:invltlb", i); intrcnt_add(buf, &ipi_invltlb_counts[i]); snprintf(buf, sizeof(buf), "cpu%d:invlrng", i); intrcnt_add(buf, &ipi_invlrng_counts[i]); snprintf(buf, sizeof(buf), "cpu%d:invlpg", i); intrcnt_add(buf, &ipi_invlpg_counts[i]); snprintf(buf, sizeof(buf), "cpu%d:invlcache", i); intrcnt_add(buf, &ipi_invlcache_counts[i]); snprintf(buf, sizeof(buf), "cpu%d:preempt", i); intrcnt_add(buf, &ipi_preempt_counts[i]); snprintf(buf, sizeof(buf), "cpu%d:ast", i); intrcnt_add(buf, &ipi_ast_counts[i]); snprintf(buf, sizeof(buf), "cpu%d:rendezvous", i); intrcnt_add(buf, &ipi_rendezvous_counts[i]); snprintf(buf, sizeof(buf), "cpu%d:hardclock", i); intrcnt_add(buf, &ipi_hardclock_counts[i]); } } SYSINIT(mp_ipi_intrcnt, SI_SUB_INTR, SI_ORDER_MIDDLE, mp_ipi_intrcnt, NULL); #endif Index: stable/10/sys/i386/i386/mp_machdep.c =================================================================== --- stable/10/sys/i386/i386/mp_machdep.c (revision 281559) +++ stable/10/sys/i386/i386/mp_machdep.c (revision 281560) @@ -1,1660 +1,1678 @@ /*- * Copyright (c) 1996, by Steve Passe * All rights reserved. * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * 1. Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * 2. The name of the developer may NOT be used to endorse or promote products * derived from this software without specific prior written permission. * * THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE * ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF * SUCH DAMAGE. */ #include __FBSDID("$FreeBSD$"); #include "opt_apic.h" #include "opt_cpu.h" #include "opt_kstack_pages.h" #include "opt_pmap.h" #include "opt_sched.h" #include "opt_smp.h" #if !defined(lint) #if !defined(SMP) #error How did you get here? #endif #ifndef DEV_APIC #error The apic device is required for SMP, add "device apic" to your config file. #endif #if defined(CPU_DISABLE_CMPXCHG) && !defined(COMPILING_LINT) #error SMP not supported with CPU_DISABLE_CMPXCHG #endif #endif /* not lint */ #include #include #include #include /* cngetc() */ #include #ifdef GPROF #include #endif #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #define WARMBOOT_TARGET 0 #define WARMBOOT_OFF (KERNBASE + 0x0467) #define WARMBOOT_SEG (KERNBASE + 0x0469) #define CMOS_REG (0x70) #define CMOS_DATA (0x71) #define BIOS_RESET (0x0f) #define BIOS_WARM (0x0a) /* * this code MUST be enabled here and in mpboot.s. * it follows the very early stages of AP boot by placing values in CMOS ram. * it NORMALLY will never be needed and thus the primitive method for enabling. * #define CHECK_POINTS */ #if defined(CHECK_POINTS) && !defined(PC98) #define CHECK_READ(A) (outb(CMOS_REG, (A)), inb(CMOS_DATA)) #define CHECK_WRITE(A,D) (outb(CMOS_REG, (A)), outb(CMOS_DATA, (D))) #define CHECK_INIT(D); \ CHECK_WRITE(0x34, (D)); \ CHECK_WRITE(0x35, (D)); \ CHECK_WRITE(0x36, (D)); \ CHECK_WRITE(0x37, (D)); \ CHECK_WRITE(0x38, (D)); \ CHECK_WRITE(0x39, (D)); #define CHECK_PRINT(S); \ printf("%s: %d, %d, %d, %d, %d, %d\n", \ (S), \ CHECK_READ(0x34), \ CHECK_READ(0x35), \ CHECK_READ(0x36), \ CHECK_READ(0x37), \ CHECK_READ(0x38), \ CHECK_READ(0x39)); #else /* CHECK_POINTS */ #define CHECK_INIT(D) #define CHECK_PRINT(S) #define CHECK_WRITE(A, D) #endif /* CHECK_POINTS */ /* lock region used by kernel profiling */ int mcount_lock; int mp_naps; /* # of Applications processors */ int boot_cpu_id = -1; /* designated BSP */ extern struct pcpu __pcpu[]; /* AP uses this during bootstrap. Do not staticize. */ char *bootSTK; static int bootAP; /* Free these after use */ void *bootstacks[MAXCPU]; static void *dpcpu; struct pcb stoppcbs[MAXCPU]; struct susppcb **susppcbs; /* Variables needed for SMP tlb shootdown. */ vm_offset_t smp_tlb_addr1; vm_offset_t smp_tlb_addr2; volatile int smp_tlb_wait; #ifdef COUNT_IPIS /* Interrupt counts. */ static u_long *ipi_preempt_counts[MAXCPU]; static u_long *ipi_ast_counts[MAXCPU]; u_long *ipi_invltlb_counts[MAXCPU]; u_long *ipi_invlrng_counts[MAXCPU]; u_long *ipi_invlpg_counts[MAXCPU]; u_long *ipi_invlcache_counts[MAXCPU]; u_long *ipi_rendezvous_counts[MAXCPU]; u_long *ipi_lazypmap_counts[MAXCPU]; static u_long *ipi_hardclock_counts[MAXCPU]; #endif /* Default cpu_ops implementation. */ struct cpu_ops cpu_ops = { .ipi_vectored = lapic_ipi_vectored }; /* * Local data and functions. */ static volatile cpuset_t ipi_nmi_pending; /* used to hold the AP's until we are ready to release them */ static struct mtx ap_boot_mtx; /* Set to 1 once we're ready to let the APs out of the pen. */ static volatile int aps_ready = 0; /* * Store data from cpu_add() until later in the boot when we actually setup * the APs. */ struct cpu_info { int cpu_present:1; int cpu_bsp:1; int cpu_disabled:1; int cpu_hyperthread:1; } static cpu_info[MAX_APIC_ID + 1]; int cpu_apic_ids[MAXCPU]; int apic_cpuids[MAX_APIC_ID + 1]; /* Holds pending bitmap based IPIs per CPU */ volatile u_int cpu_ipi_pending[MAXCPU]; static u_int boot_address; static int cpu_logical; /* logical cpus per core */ static int cpu_cores; /* cores per package */ static void assign_cpu_ids(void); static void install_ap_tramp(void); static void set_interrupt_apic_ids(void); static int start_all_aps(void); static int start_ap(int apic_id); static void release_aps(void *dummy); static u_int hyperthreading_cpus; /* logical cpus sharing L1 cache */ static int hyperthreading_allowed = 1; static void mem_range_AP_init(void) { if (mem_range_softc.mr_op && mem_range_softc.mr_op->initAP) mem_range_softc.mr_op->initAP(&mem_range_softc); } static void topo_probe_amd(void) { int core_id_bits; int id; /* AMD processors do not support HTT. */ cpu_logical = 1; if ((amd_feature2 & AMDID2_CMP) == 0) { cpu_cores = 1; return; } core_id_bits = (cpu_procinfo2 & AMDID_COREID_SIZE) >> AMDID_COREID_SIZE_SHIFT; if (core_id_bits == 0) { cpu_cores = (cpu_procinfo2 & AMDID_CMP_CORES) + 1; return; } /* Fam 10h and newer should get here. */ for (id = 0; id <= MAX_APIC_ID; id++) { /* Check logical CPU availability. */ if (!cpu_info[id].cpu_present || cpu_info[id].cpu_disabled) continue; /* Check if logical CPU has the same package ID. */ if ((id >> core_id_bits) != (boot_cpu_id >> core_id_bits)) continue; cpu_cores++; } } /* * Round up to the next power of two, if necessary, and then * take log2. * Returns -1 if argument is zero. */ static __inline int mask_width(u_int x) { return (fls(x << (1 - powerof2(x))) - 1); } static void topo_probe_0x4(void) { u_int p[4]; int pkg_id_bits; int core_id_bits; int max_cores; int max_logical; int id; /* Both zero and one here mean one logical processor per package. */ max_logical = (cpu_feature & CPUID_HTT) != 0 ? (cpu_procinfo & CPUID_HTT_CORES) >> 16 : 1; if (max_logical <= 1) return; /* * Because of uniformity assumption we examine only * those logical processors that belong to the same * package as BSP. Further, we count number of * logical processors that belong to the same core * as BSP thus deducing number of threads per core. */ if (cpu_high >= 0x4) { cpuid_count(0x04, 0, p); max_cores = ((p[0] >> 26) & 0x3f) + 1; } else max_cores = 1; core_id_bits = mask_width(max_logical/max_cores); if (core_id_bits < 0) return; pkg_id_bits = core_id_bits + mask_width(max_cores); for (id = 0; id <= MAX_APIC_ID; id++) { /* Check logical CPU availability. */ if (!cpu_info[id].cpu_present || cpu_info[id].cpu_disabled) continue; /* Check if logical CPU has the same package ID. */ if ((id >> pkg_id_bits) != (boot_cpu_id >> pkg_id_bits)) continue; cpu_cores++; /* Check if logical CPU has the same package and core IDs. */ if ((id >> core_id_bits) == (boot_cpu_id >> core_id_bits)) cpu_logical++; } KASSERT(cpu_cores >= 1 && cpu_logical >= 1, ("topo_probe_0x4 couldn't find BSP")); cpu_cores /= cpu_logical; hyperthreading_cpus = cpu_logical; } static void topo_probe_0xb(void) { u_int p[4]; int bits; int cnt; int i; int logical; int type; int x; /* We only support three levels for now. */ for (i = 0; i < 3; i++) { cpuid_count(0x0b, i, p); /* Fall back if CPU leaf 11 doesn't really exist. */ if (i == 0 && p[1] == 0) { topo_probe_0x4(); return; } bits = p[0] & 0x1f; logical = p[1] &= 0xffff; type = (p[2] >> 8) & 0xff; if (type == 0 || logical == 0) break; /* * Because of uniformity assumption we examine only * those logical processors that belong to the same * package as BSP. */ for (cnt = 0, x = 0; x <= MAX_APIC_ID; x++) { if (!cpu_info[x].cpu_present || cpu_info[x].cpu_disabled) continue; if (x >> bits == boot_cpu_id >> bits) cnt++; } if (type == CPUID_TYPE_SMT) cpu_logical = cnt; else if (type == CPUID_TYPE_CORE) cpu_cores = cnt; } if (cpu_logical == 0) cpu_logical = 1; cpu_cores /= cpu_logical; } /* * Both topology discovery code and code that consumes topology * information assume top-down uniformity of the topology. * That is, all physical packages must be identical and each * core in a package must have the same number of threads. * Topology information is queried only on BSP, on which this * code runs and for which it can query CPUID information. * Then topology is extrapolated on all packages using the * uniformity assumption. */ static void topo_probe(void) { static int cpu_topo_probed = 0; if (cpu_topo_probed) return; CPU_ZERO(&logical_cpus_mask); if (mp_ncpus <= 1) cpu_cores = cpu_logical = 1; else if (cpu_vendor_id == CPU_VENDOR_AMD) topo_probe_amd(); else if (cpu_vendor_id == CPU_VENDOR_INTEL) { /* * See Intel(R) 64 Architecture Processor * Topology Enumeration article for details. * * Note that 0x1 <= cpu_high < 4 case should be * compatible with topo_probe_0x4() logic when * CPUID.1:EBX[23:16] > 0 (cpu_cores will be 1) * or it should trigger the fallback otherwise. */ if (cpu_high >= 0xb) topo_probe_0xb(); else if (cpu_high >= 0x1) topo_probe_0x4(); } /* * Fallback: assume each logical CPU is in separate * physical package. That is, no multi-core, no SMT. */ if (cpu_cores == 0 || cpu_logical == 0) cpu_cores = cpu_logical = 1; cpu_topo_probed = 1; } struct cpu_group * cpu_topo(void) { int cg_flags; /* * Determine whether any threading flags are * necessry. */ topo_probe(); if (cpu_logical > 1 && hyperthreading_cpus) cg_flags = CG_FLAG_HTT; else if (cpu_logical > 1) cg_flags = CG_FLAG_SMT; else cg_flags = 0; if (mp_ncpus % (cpu_cores * cpu_logical) != 0) { printf("WARNING: Non-uniform processors.\n"); printf("WARNING: Using suboptimal topology.\n"); return (smp_topo_none()); } /* * No multi-core or hyper-threaded. */ if (cpu_logical * cpu_cores == 1) return (smp_topo_none()); /* * Only HTT no multi-core. */ if (cpu_logical > 1 && cpu_cores == 1) return (smp_topo_1level(CG_SHARE_L1, cpu_logical, cg_flags)); /* * Only multi-core no HTT. */ if (cpu_cores > 1 && cpu_logical == 1) return (smp_topo_1level(CG_SHARE_L2, cpu_cores, cg_flags)); /* * Both HTT and multi-core. */ return (smp_topo_2level(CG_SHARE_L2, cpu_cores, CG_SHARE_L1, cpu_logical, cg_flags)); } /* * Calculate usable address in base memory for AP trampoline code. */ u_int mp_bootaddress(u_int basemem) { boot_address = trunc_page(basemem); /* round down to 4k boundary */ if ((basemem - boot_address) < bootMP_size) boot_address -= PAGE_SIZE; /* not enough, lower by 4k */ return boot_address; } void cpu_add(u_int apic_id, char boot_cpu) { if (apic_id > MAX_APIC_ID) { panic("SMP: APIC ID %d too high", apic_id); return; } KASSERT(cpu_info[apic_id].cpu_present == 0, ("CPU %d added twice", apic_id)); cpu_info[apic_id].cpu_present = 1; if (boot_cpu) { KASSERT(boot_cpu_id == -1, ("CPU %d claims to be BSP, but CPU %d already is", apic_id, boot_cpu_id)); boot_cpu_id = apic_id; cpu_info[apic_id].cpu_bsp = 1; } if (mp_ncpus < MAXCPU) { mp_ncpus++; mp_maxid = mp_ncpus - 1; } if (bootverbose) printf("SMP: Added CPU %d (%s)\n", apic_id, boot_cpu ? "BSP" : "AP"); } void cpu_mp_setmaxid(void) { /* * mp_maxid should be already set by calls to cpu_add(). * Just sanity check its value here. */ if (mp_ncpus == 0) KASSERT(mp_maxid == 0, ("%s: mp_ncpus is zero, but mp_maxid is not", __func__)); else if (mp_ncpus == 1) mp_maxid = 0; else KASSERT(mp_maxid >= mp_ncpus - 1, ("%s: counters out of sync: max %d, count %d", __func__, mp_maxid, mp_ncpus)); } int cpu_mp_probe(void) { /* * Always record BSP in CPU map so that the mbuf init code works * correctly. */ CPU_SETOF(0, &all_cpus); if (mp_ncpus == 0) { /* * No CPUs were found, so this must be a UP system. Setup * the variables to represent a system with a single CPU * with an id of 0. */ mp_ncpus = 1; return (0); } /* At least one CPU was found. */ if (mp_ncpus == 1) { /* * One CPU was found, so this must be a UP system with * an I/O APIC. */ mp_maxid = 0; return (0); } /* At least two CPUs were found. */ return (1); } /* * Initialize the IPI handlers and start up the AP's. */ void cpu_mp_start(void) { int i; /* Initialize the logical ID to APIC ID table. */ for (i = 0; i < MAXCPU; i++) { cpu_apic_ids[i] = -1; cpu_ipi_pending[i] = 0; } /* Install an inter-CPU IPI for TLB invalidation */ setidt(IPI_INVLTLB, IDTVEC(invltlb), SDT_SYS386IGT, SEL_KPL, GSEL(GCODE_SEL, SEL_KPL)); setidt(IPI_INVLPG, IDTVEC(invlpg), SDT_SYS386IGT, SEL_KPL, GSEL(GCODE_SEL, SEL_KPL)); setidt(IPI_INVLRNG, IDTVEC(invlrng), SDT_SYS386IGT, SEL_KPL, GSEL(GCODE_SEL, SEL_KPL)); /* Install an inter-CPU IPI for cache invalidation. */ setidt(IPI_INVLCACHE, IDTVEC(invlcache), SDT_SYS386IGT, SEL_KPL, GSEL(GCODE_SEL, SEL_KPL)); /* Install an inter-CPU IPI for lazy pmap release */ setidt(IPI_LAZYPMAP, IDTVEC(lazypmap), SDT_SYS386IGT, SEL_KPL, GSEL(GCODE_SEL, SEL_KPL)); /* Install an inter-CPU IPI for all-CPU rendezvous */ setidt(IPI_RENDEZVOUS, IDTVEC(rendezvous), SDT_SYS386IGT, SEL_KPL, GSEL(GCODE_SEL, SEL_KPL)); /* Install generic inter-CPU IPI handler */ setidt(IPI_BITMAP_VECTOR, IDTVEC(ipi_intr_bitmap_handler), SDT_SYS386IGT, SEL_KPL, GSEL(GCODE_SEL, SEL_KPL)); /* Install an inter-CPU IPI for CPU stop/restart */ setidt(IPI_STOP, IDTVEC(cpustop), SDT_SYS386IGT, SEL_KPL, GSEL(GCODE_SEL, SEL_KPL)); /* Install an inter-CPU IPI for CPU suspend/resume */ setidt(IPI_SUSPEND, IDTVEC(cpususpend), SDT_SYS386IGT, SEL_KPL, GSEL(GCODE_SEL, SEL_KPL)); /* Set boot_cpu_id if needed. */ if (boot_cpu_id == -1) { boot_cpu_id = PCPU_GET(apic_id); cpu_info[boot_cpu_id].cpu_bsp = 1; } else KASSERT(boot_cpu_id == PCPU_GET(apic_id), ("BSP's APIC ID doesn't match boot_cpu_id")); /* Probe logical/physical core configuration. */ topo_probe(); assign_cpu_ids(); /* Start each Application Processor */ start_all_aps(); set_interrupt_apic_ids(); } /* * Print various information about the SMP system hardware and setup. */ void cpu_mp_announce(void) { const char *hyperthread; int i; printf("FreeBSD/SMP: %d package(s) x %d core(s)", mp_ncpus / (cpu_cores * cpu_logical), cpu_cores); if (hyperthreading_cpus > 1) printf(" x %d HTT threads", cpu_logical); else if (cpu_logical > 1) printf(" x %d SMT threads", cpu_logical); printf("\n"); /* List active CPUs first. */ printf(" cpu0 (BSP): APIC ID: %2d\n", boot_cpu_id); for (i = 1; i < mp_ncpus; i++) { if (cpu_info[cpu_apic_ids[i]].cpu_hyperthread) hyperthread = "/HT"; else hyperthread = ""; printf(" cpu%d (AP%s): APIC ID: %2d\n", i, hyperthread, cpu_apic_ids[i]); } /* List disabled CPUs last. */ for (i = 0; i <= MAX_APIC_ID; i++) { if (!cpu_info[i].cpu_present || !cpu_info[i].cpu_disabled) continue; if (cpu_info[i].cpu_hyperthread) hyperthread = "/HT"; else hyperthread = ""; printf(" cpu (AP%s): APIC ID: %2d (disabled)\n", hyperthread, i); } } /* * AP CPU's call this to initialize themselves. */ void init_secondary(void) { struct pcpu *pc; vm_offset_t addr; int gsel_tss; int x, myid; u_int cpuid, cr0; /* bootAP is set in start_ap() to our ID. */ myid = bootAP; /* Get per-cpu data */ pc = &__pcpu[myid]; /* prime data page for it to use */ pcpu_init(pc, myid, sizeof(struct pcpu)); dpcpu_init(dpcpu, myid); pc->pc_apic_id = cpu_apic_ids[myid]; pc->pc_prvspace = pc; pc->pc_curthread = 0; gdt_segs[GPRIV_SEL].ssd_base = (int) pc; gdt_segs[GPROC0_SEL].ssd_base = (int) &pc->pc_common_tss; for (x = 0; x < NGDT; x++) { ssdtosd(&gdt_segs[x], &gdt[myid * NGDT + x].sd); } r_gdt.rd_limit = NGDT * sizeof(gdt[0]) - 1; r_gdt.rd_base = (int) &gdt[myid * NGDT]; lgdt(&r_gdt); /* does magic intra-segment return */ lidt(&r_idt); lldt(_default_ldt); PCPU_SET(currentldt, _default_ldt); gsel_tss = GSEL(GPROC0_SEL, SEL_KPL); gdt[myid * NGDT + GPROC0_SEL].sd.sd_type = SDT_SYS386TSS; PCPU_SET(common_tss.tss_esp0, 0); /* not used until after switch */ PCPU_SET(common_tss.tss_ss0, GSEL(GDATA_SEL, SEL_KPL)); PCPU_SET(common_tss.tss_ioopt, (sizeof (struct i386tss)) << 16); PCPU_SET(tss_gdt, &gdt[myid * NGDT + GPROC0_SEL].sd); PCPU_SET(common_tssd, *PCPU_GET(tss_gdt)); ltr(gsel_tss); PCPU_SET(fsgs_gdt, &gdt[myid * NGDT + GUFS_SEL].sd); /* * Set to a known state: * Set by mpboot.s: CR0_PG, CR0_PE * Set by cpu_setregs: CR0_NE, CR0_MP, CR0_TS, CR0_WP, CR0_AM */ cr0 = rcr0(); cr0 &= ~(CR0_CD | CR0_NW | CR0_EM); load_cr0(cr0); CHECK_WRITE(0x38, 5); /* Disable local APIC just to be sure. */ lapic_disable(); /* signal our startup to the BSP. */ mp_naps++; CHECK_WRITE(0x39, 6); /* Spin until the BSP releases the AP's. */ while (!aps_ready) ia32_pause(); /* BSP may have changed PTD while we were waiting */ invltlb(); for (addr = 0; addr < NKPT * NBPDR - 1; addr += PAGE_SIZE) invlpg(addr); #if defined(I586_CPU) && !defined(NO_F00F_HACK) lidt(&r_idt); #endif /* Initialize the PAT MSR if present. */ pmap_init_pat(); /* set up CPU registers and state */ cpu_setregs(); /* set up SSE/NX */ initializecpu(); /* set up FPU state on the AP */ npxinit(false); if (cpu_ops.cpu_init) cpu_ops.cpu_init(); /* A quick check from sanity claus */ cpuid = PCPU_GET(cpuid); if (PCPU_GET(apic_id) != lapic_id()) { printf("SMP: cpuid = %d\n", cpuid); printf("SMP: actual apic_id = %d\n", lapic_id()); printf("SMP: correct apic_id = %d\n", PCPU_GET(apic_id)); panic("cpuid mismatch! boom!!"); } /* Initialize curthread. */ KASSERT(PCPU_GET(idlethread) != NULL, ("no idle thread")); PCPU_SET(curthread, PCPU_GET(idlethread)); mca_init(); mtx_lock_spin(&ap_boot_mtx); /* Init local apic for irq's */ lapic_setup(1); /* Set memory range attributes for this CPU to match the BSP */ mem_range_AP_init(); smp_cpus++; CTR1(KTR_SMP, "SMP: AP CPU #%d Launched", cpuid); printf("SMP: AP CPU #%d Launched!\n", cpuid); /* Determine if we are a logical CPU. */ /* XXX Calculation depends on cpu_logical being a power of 2, e.g. 2 */ if (cpu_logical > 1 && PCPU_GET(apic_id) % cpu_logical != 0) CPU_SET(cpuid, &logical_cpus_mask); if (bootverbose) lapic_dump("AP"); if (smp_cpus == mp_ncpus) { /* enable IPI's, tlb shootdown, freezes etc */ atomic_store_rel_int(&smp_started, 1); } mtx_unlock_spin(&ap_boot_mtx); /* Wait until all the AP's are up. */ while (smp_started == 0) ia32_pause(); /* Start per-CPU event timers. */ cpu_initclocks_ap(); /* Enter the scheduler. */ sched_throw(NULL); panic("scheduler returned us to %s", __func__); /* NOTREACHED */ } /******************************************************************* * local functions and data */ /* * We tell the I/O APIC code about all the CPUs we want to receive * interrupts. If we don't want certain CPUs to receive IRQs we * can simply not tell the I/O APIC code about them in this function. * We also do not tell it about the BSP since it tells itself about * the BSP internally to work with UP kernels and on UP machines. */ static void set_interrupt_apic_ids(void) { u_int i, apic_id; for (i = 0; i < MAXCPU; i++) { apic_id = cpu_apic_ids[i]; if (apic_id == -1) continue; if (cpu_info[apic_id].cpu_bsp) continue; if (cpu_info[apic_id].cpu_disabled) continue; /* Don't let hyperthreads service interrupts. */ if (hyperthreading_cpus > 1 && apic_id % hyperthreading_cpus != 0) continue; intr_add_cpu(i); } } /* * Assign logical CPU IDs to local APICs. */ static void assign_cpu_ids(void) { u_int i; TUNABLE_INT_FETCH("machdep.hyperthreading_allowed", &hyperthreading_allowed); /* Check for explicitly disabled CPUs. */ for (i = 0; i <= MAX_APIC_ID; i++) { if (!cpu_info[i].cpu_present || cpu_info[i].cpu_bsp) continue; if (hyperthreading_cpus > 1 && i % hyperthreading_cpus != 0) { cpu_info[i].cpu_hyperthread = 1; /* * Don't use HT CPU if it has been disabled by a * tunable. */ if (hyperthreading_allowed == 0) { cpu_info[i].cpu_disabled = 1; continue; } } /* Don't use this CPU if it has been disabled by a tunable. */ if (resource_disabled("lapic", i)) { cpu_info[i].cpu_disabled = 1; continue; } } if (hyperthreading_allowed == 0 && hyperthreading_cpus > 1) { hyperthreading_cpus = 0; cpu_logical = 1; } /* * Assign CPU IDs to local APIC IDs and disable any CPUs * beyond MAXCPU. CPU 0 is always assigned to the BSP. * * To minimize confusion for userland, we attempt to number * CPUs such that all threads and cores in a package are * grouped together. For now we assume that the BSP is always * the first thread in a package and just start adding APs * starting with the BSP's APIC ID. */ mp_ncpus = 1; cpu_apic_ids[0] = boot_cpu_id; apic_cpuids[boot_cpu_id] = 0; for (i = boot_cpu_id + 1; i != boot_cpu_id; i == MAX_APIC_ID ? i = 0 : i++) { if (!cpu_info[i].cpu_present || cpu_info[i].cpu_bsp || cpu_info[i].cpu_disabled) continue; if (mp_ncpus < MAXCPU) { cpu_apic_ids[mp_ncpus] = i; apic_cpuids[i] = mp_ncpus; mp_ncpus++; } else cpu_info[i].cpu_disabled = 1; } KASSERT(mp_maxid >= mp_ncpus - 1, ("%s: counters out of sync: max %d, count %d", __func__, mp_maxid, mp_ncpus)); } /* * start each AP in our list */ /* Lowest 1MB is already mapped: don't touch*/ #define TMPMAP_START 1 static int start_all_aps(void) { #ifndef PC98 u_char mpbiosreason; #endif u_int32_t mpbioswarmvec; int apic_id, cpu, i; mtx_init(&ap_boot_mtx, "ap boot", NULL, MTX_SPIN); /* install the AP 1st level boot code */ install_ap_tramp(); /* save the current value of the warm-start vector */ mpbioswarmvec = *((u_int32_t *) WARMBOOT_OFF); #ifndef PC98 outb(CMOS_REG, BIOS_RESET); mpbiosreason = inb(CMOS_DATA); #endif /* set up temporary P==V mapping for AP boot */ /* XXX this is a hack, we should boot the AP on its own stack/PTD */ for (i = TMPMAP_START; i < NKPT; i++) PTD[i] = PTD[KPTDI + i]; invltlb(); /* start each AP */ for (cpu = 1; cpu < mp_ncpus; cpu++) { apic_id = cpu_apic_ids[cpu]; /* allocate and set up a boot stack data page */ bootstacks[cpu] = (char *)kmem_malloc(kernel_arena, KSTACK_PAGES * PAGE_SIZE, M_WAITOK | M_ZERO); dpcpu = (void *)kmem_malloc(kernel_arena, DPCPU_SIZE, M_WAITOK | M_ZERO); /* setup a vector to our boot code */ *((volatile u_short *) WARMBOOT_OFF) = WARMBOOT_TARGET; *((volatile u_short *) WARMBOOT_SEG) = (boot_address >> 4); #ifndef PC98 outb(CMOS_REG, BIOS_RESET); outb(CMOS_DATA, BIOS_WARM); /* 'warm-start' */ #endif bootSTK = (char *)bootstacks[cpu] + KSTACK_PAGES * PAGE_SIZE - 4; bootAP = cpu; /* attempt to start the Application Processor */ CHECK_INIT(99); /* setup checkpoints */ if (!start_ap(apic_id)) { printf("AP #%d (PHY# %d) failed!\n", cpu, apic_id); CHECK_PRINT("trace"); /* show checkpoints */ /* better panic as the AP may be running loose */ printf("panic y/n? [y] "); if (cngetc() != 'n') panic("bye-bye"); } CHECK_PRINT("trace"); /* show checkpoints */ CPU_SET(cpu, &all_cpus); /* record AP in CPU map */ } /* restore the warmstart vector */ *(u_int32_t *) WARMBOOT_OFF = mpbioswarmvec; #ifndef PC98 outb(CMOS_REG, BIOS_RESET); outb(CMOS_DATA, mpbiosreason); #endif /* Undo V==P hack from above */ for (i = TMPMAP_START; i < NKPT; i++) PTD[i] = 0; pmap_invalidate_range(kernel_pmap, 0, NKPT * NBPDR - 1); /* number of APs actually started */ return mp_naps; } /* * load the 1st level AP boot code into base memory. */ /* targets for relocation */ extern void bigJump(void); extern void bootCodeSeg(void); extern void bootDataSeg(void); extern void MPentry(void); extern u_int MP_GDT; extern u_int mp_gdtbase; static void install_ap_tramp(void) { int x; int size = *(int *) ((u_long) & bootMP_size); vm_offset_t va = boot_address + KERNBASE; u_char *src = (u_char *) ((u_long) bootMP); u_char *dst = (u_char *) va; u_int boot_base = (u_int) bootMP; u_int8_t *dst8; u_int16_t *dst16; u_int32_t *dst32; KASSERT (size <= PAGE_SIZE, ("'size' do not fit into PAGE_SIZE, as expected.")); pmap_kenter(va, boot_address); pmap_invalidate_page (kernel_pmap, va); for (x = 0; x < size; ++x) *dst++ = *src++; /* * modify addresses in code we just moved to basemem. unfortunately we * need fairly detailed info about mpboot.s for this to work. changes * to mpboot.s might require changes here. */ /* boot code is located in KERNEL space */ dst = (u_char *) va; /* modify the lgdt arg */ dst32 = (u_int32_t *) (dst + ((u_int) & mp_gdtbase - boot_base)); *dst32 = boot_address + ((u_int) & MP_GDT - boot_base); /* modify the ljmp target for MPentry() */ dst32 = (u_int32_t *) (dst + ((u_int) bigJump - boot_base) + 1); *dst32 = ((u_int) MPentry - KERNBASE); /* modify the target for boot code segment */ dst16 = (u_int16_t *) (dst + ((u_int) bootCodeSeg - boot_base)); dst8 = (u_int8_t *) (dst16 + 1); *dst16 = (u_int) boot_address & 0xffff; *dst8 = ((u_int) boot_address >> 16) & 0xff; /* modify the target for boot data segment */ dst16 = (u_int16_t *) (dst + ((u_int) bootDataSeg - boot_base)); dst8 = (u_int8_t *) (dst16 + 1); *dst16 = (u_int) boot_address & 0xffff; *dst8 = ((u_int) boot_address >> 16) & 0xff; } /* * This function starts the AP (application processor) identified * by the APIC ID 'physicalCpu'. It does quite a "song and dance" * to accomplish this. This is necessary because of the nuances * of the different hardware we might encounter. It isn't pretty, * but it seems to work. */ static int start_ap(int apic_id) { int vector, ms; int cpus; /* calculate the vector */ vector = (boot_address >> 12) & 0xff; /* used as a watchpoint to signal AP startup */ cpus = mp_naps; ipi_startup(apic_id, vector); /* Wait up to 5 seconds for it to start. */ for (ms = 0; ms < 5000; ms++) { if (mp_naps > cpus) return 1; /* return SUCCESS */ DELAY(1000); } return 0; /* return FAILURE */ } #ifdef COUNT_XINVLTLB_HITS u_int xhits_gbl[MAXCPU]; u_int xhits_pg[MAXCPU]; u_int xhits_rng[MAXCPU]; static SYSCTL_NODE(_debug, OID_AUTO, xhits, CTLFLAG_RW, 0, ""); SYSCTL_OPAQUE(_debug_xhits, OID_AUTO, global, CTLFLAG_RW, &xhits_gbl, sizeof(xhits_gbl), "IU", ""); SYSCTL_OPAQUE(_debug_xhits, OID_AUTO, page, CTLFLAG_RW, &xhits_pg, sizeof(xhits_pg), "IU", ""); SYSCTL_OPAQUE(_debug_xhits, OID_AUTO, range, CTLFLAG_RW, &xhits_rng, sizeof(xhits_rng), "IU", ""); u_int ipi_global; u_int ipi_page; u_int ipi_range; u_int ipi_range_size; SYSCTL_INT(_debug_xhits, OID_AUTO, ipi_global, CTLFLAG_RW, &ipi_global, 0, ""); SYSCTL_INT(_debug_xhits, OID_AUTO, ipi_page, CTLFLAG_RW, &ipi_page, 0, ""); SYSCTL_INT(_debug_xhits, OID_AUTO, ipi_range, CTLFLAG_RW, &ipi_range, 0, ""); SYSCTL_INT(_debug_xhits, OID_AUTO, ipi_range_size, CTLFLAG_RW, &ipi_range_size, 0, ""); u_int ipi_masked_global; u_int ipi_masked_page; u_int ipi_masked_range; u_int ipi_masked_range_size; SYSCTL_INT(_debug_xhits, OID_AUTO, ipi_masked_global, CTLFLAG_RW, &ipi_masked_global, 0, ""); SYSCTL_INT(_debug_xhits, OID_AUTO, ipi_masked_page, CTLFLAG_RW, &ipi_masked_page, 0, ""); SYSCTL_INT(_debug_xhits, OID_AUTO, ipi_masked_range, CTLFLAG_RW, &ipi_masked_range, 0, ""); SYSCTL_INT(_debug_xhits, OID_AUTO, ipi_masked_range_size, CTLFLAG_RW, &ipi_masked_range_size, 0, ""); #endif /* COUNT_XINVLTLB_HITS */ /* * Init and startup IPI. */ void ipi_startup(int apic_id, int vector) { /* + * This attempts to follow the algorithm described in the + * Intel Multiprocessor Specification v1.4 in section B.4. + * For each IPI, we allow the local APIC ~20us to deliver the + * IPI. If that times out, we panic. + */ + + /* * first we do an INIT IPI: this INIT IPI might be run, resetting * and running the target CPU. OR this INIT IPI might be latched (P5 * bug), CPU waiting for STARTUP IPI. OR this INIT IPI might be * ignored. */ - lapic_ipi_raw(APIC_DEST_DESTFLD | APIC_TRIGMOD_EDGE | + lapic_ipi_raw(APIC_DEST_DESTFLD | APIC_TRIGMOD_LEVEL | APIC_LEVEL_ASSERT | APIC_DESTMODE_PHY | APIC_DELMODE_INIT, apic_id); - lapic_ipi_wait(-1); + lapic_ipi_wait(100); + + /* Explicitly deassert the INIT IPI. */ + lapic_ipi_raw(APIC_DEST_DESTFLD | APIC_TRIGMOD_LEVEL | + APIC_LEVEL_DEASSERT | APIC_DESTMODE_PHY | APIC_DELMODE_INIT, + apic_id); + DELAY(10000); /* wait ~10mS */ /* * next we do a STARTUP IPI: the previous INIT IPI might still be * latched, (P5 bug) this 1st STARTUP would then terminate * immediately, and the previously started INIT IPI would continue. OR * the previous INIT IPI has already run. and this STARTUP IPI will * run. OR the previous INIT IPI was ignored. and this STARTUP IPI * will run. */ lapic_ipi_raw(APIC_DEST_DESTFLD | APIC_TRIGMOD_EDGE | - APIC_LEVEL_DEASSERT | APIC_DESTMODE_PHY | APIC_DELMODE_STARTUP | + APIC_LEVEL_ASSERT | APIC_DESTMODE_PHY | APIC_DELMODE_STARTUP | vector, apic_id); - lapic_ipi_wait(-1); + if (!lapic_ipi_wait(100)) + panic("Failed to deliver first STARTUP IPI to APIC %d", + apic_id); DELAY(200); /* wait ~200uS */ /* * finally we do a 2nd STARTUP IPI: this 2nd STARTUP IPI should run IF * the previous STARTUP IPI was cancelled by a latched INIT IPI. OR * this STARTUP IPI will be ignored, as only ONE STARTUP IPI is * recognized after hardware RESET or INIT IPI. */ lapic_ipi_raw(APIC_DEST_DESTFLD | APIC_TRIGMOD_EDGE | - APIC_LEVEL_DEASSERT | APIC_DESTMODE_PHY | APIC_DELMODE_STARTUP | + APIC_LEVEL_ASSERT | APIC_DESTMODE_PHY | APIC_DELMODE_STARTUP | vector, apic_id); - lapic_ipi_wait(-1); + if (!lapic_ipi_wait(100)) + panic("Failed to deliver second STARTUP IPI to APIC %d", + apic_id); + DELAY(200); /* wait ~200uS */ } /* * Send an IPI to specified CPU handling the bitmap logic. */ static void ipi_send_cpu(int cpu, u_int ipi) { u_int bitmap, old_pending, new_pending; KASSERT(cpu_apic_ids[cpu] != -1, ("IPI to non-existent CPU %d", cpu)); if (IPI_IS_BITMAPED(ipi)) { bitmap = 1 << ipi; ipi = IPI_BITMAP_VECTOR; do { old_pending = cpu_ipi_pending[cpu]; new_pending = old_pending | bitmap; } while (!atomic_cmpset_int(&cpu_ipi_pending[cpu], old_pending, new_pending)); if (old_pending) return; } cpu_ops.ipi_vectored(ipi, cpu_apic_ids[cpu]); } /* * Flush the TLB on all other CPU's */ static void smp_tlb_shootdown(u_int vector, vm_offset_t addr1, vm_offset_t addr2) { u_int ncpu; ncpu = mp_ncpus - 1; /* does not shootdown self */ if (ncpu < 1) return; /* no other cpus */ if (!(read_eflags() & PSL_I)) panic("%s: interrupts disabled", __func__); mtx_lock_spin(&smp_ipi_mtx); smp_tlb_addr1 = addr1; smp_tlb_addr2 = addr2; atomic_store_rel_int(&smp_tlb_wait, 0); ipi_all_but_self(vector); while (smp_tlb_wait < ncpu) ia32_pause(); mtx_unlock_spin(&smp_ipi_mtx); } static void smp_targeted_tlb_shootdown(cpuset_t mask, u_int vector, vm_offset_t addr1, vm_offset_t addr2) { int cpu, ncpu, othercpus; othercpus = mp_ncpus - 1; if (CPU_ISFULLSET(&mask)) { if (othercpus < 1) return; } else { CPU_CLR(PCPU_GET(cpuid), &mask); if (CPU_EMPTY(&mask)) return; } if (!(read_eflags() & PSL_I)) panic("%s: interrupts disabled", __func__); mtx_lock_spin(&smp_ipi_mtx); smp_tlb_addr1 = addr1; smp_tlb_addr2 = addr2; atomic_store_rel_int(&smp_tlb_wait, 0); if (CPU_ISFULLSET(&mask)) { ncpu = othercpus; ipi_all_but_self(vector); } else { ncpu = 0; while ((cpu = CPU_FFS(&mask)) != 0) { cpu--; CPU_CLR(cpu, &mask); CTR3(KTR_SMP, "%s: cpu: %d ipi: %x", __func__, cpu, vector); ipi_send_cpu(cpu, vector); ncpu++; } } while (smp_tlb_wait < ncpu) ia32_pause(); mtx_unlock_spin(&smp_ipi_mtx); } void smp_cache_flush(void) { if (smp_started) smp_tlb_shootdown(IPI_INVLCACHE, 0, 0); } void smp_invltlb(void) { if (smp_started) { smp_tlb_shootdown(IPI_INVLTLB, 0, 0); #ifdef COUNT_XINVLTLB_HITS ipi_global++; #endif } } void smp_invlpg(vm_offset_t addr) { if (smp_started) { smp_tlb_shootdown(IPI_INVLPG, addr, 0); #ifdef COUNT_XINVLTLB_HITS ipi_page++; #endif } } void smp_invlpg_range(vm_offset_t addr1, vm_offset_t addr2) { if (smp_started) { smp_tlb_shootdown(IPI_INVLRNG, addr1, addr2); #ifdef COUNT_XINVLTLB_HITS ipi_range++; ipi_range_size += (addr2 - addr1) / PAGE_SIZE; #endif } } void smp_masked_invltlb(cpuset_t mask) { if (smp_started) { smp_targeted_tlb_shootdown(mask, IPI_INVLTLB, 0, 0); #ifdef COUNT_XINVLTLB_HITS ipi_masked_global++; #endif } } void smp_masked_invlpg(cpuset_t mask, vm_offset_t addr) { if (smp_started) { smp_targeted_tlb_shootdown(mask, IPI_INVLPG, addr, 0); #ifdef COUNT_XINVLTLB_HITS ipi_masked_page++; #endif } } void smp_masked_invlpg_range(cpuset_t mask, vm_offset_t addr1, vm_offset_t addr2) { if (smp_started) { smp_targeted_tlb_shootdown(mask, IPI_INVLRNG, addr1, addr2); #ifdef COUNT_XINVLTLB_HITS ipi_masked_range++; ipi_masked_range_size += (addr2 - addr1) / PAGE_SIZE; #endif } } void ipi_bitmap_handler(struct trapframe frame) { struct trapframe *oldframe; struct thread *td; int cpu = PCPU_GET(cpuid); u_int ipi_bitmap; critical_enter(); td = curthread; td->td_intr_nesting_level++; oldframe = td->td_intr_frame; td->td_intr_frame = &frame; ipi_bitmap = atomic_readandclear_int(&cpu_ipi_pending[cpu]); if (ipi_bitmap & (1 << IPI_PREEMPT)) { #ifdef COUNT_IPIS (*ipi_preempt_counts[cpu])++; #endif sched_preempt(td); } if (ipi_bitmap & (1 << IPI_AST)) { #ifdef COUNT_IPIS (*ipi_ast_counts[cpu])++; #endif /* Nothing to do for AST */ } if (ipi_bitmap & (1 << IPI_HARDCLOCK)) { #ifdef COUNT_IPIS (*ipi_hardclock_counts[cpu])++; #endif hardclockintr(); } td->td_intr_frame = oldframe; td->td_intr_nesting_level--; critical_exit(); } /* * send an IPI to a set of cpus. */ void ipi_selected(cpuset_t cpus, u_int ipi) { int cpu; /* * IPI_STOP_HARD maps to a NMI and the trap handler needs a bit * of help in order to understand what is the source. * Set the mask of receiving CPUs for this purpose. */ if (ipi == IPI_STOP_HARD) CPU_OR_ATOMIC(&ipi_nmi_pending, &cpus); while ((cpu = CPU_FFS(&cpus)) != 0) { cpu--; CPU_CLR(cpu, &cpus); CTR3(KTR_SMP, "%s: cpu: %d ipi: %x", __func__, cpu, ipi); ipi_send_cpu(cpu, ipi); } } /* * send an IPI to a specific CPU. */ void ipi_cpu(int cpu, u_int ipi) { /* * IPI_STOP_HARD maps to a NMI and the trap handler needs a bit * of help in order to understand what is the source. * Set the mask of receiving CPUs for this purpose. */ if (ipi == IPI_STOP_HARD) CPU_SET_ATOMIC(cpu, &ipi_nmi_pending); CTR3(KTR_SMP, "%s: cpu: %d ipi: %x", __func__, cpu, ipi); ipi_send_cpu(cpu, ipi); } /* * send an IPI to all CPUs EXCEPT myself */ void ipi_all_but_self(u_int ipi) { cpuset_t other_cpus; other_cpus = all_cpus; CPU_CLR(PCPU_GET(cpuid), &other_cpus); if (IPI_IS_BITMAPED(ipi)) { ipi_selected(other_cpus, ipi); return; } /* * IPI_STOP_HARD maps to a NMI and the trap handler needs a bit * of help in order to understand what is the source. * Set the mask of receiving CPUs for this purpose. */ if (ipi == IPI_STOP_HARD) CPU_OR_ATOMIC(&ipi_nmi_pending, &other_cpus); CTR2(KTR_SMP, "%s: ipi: %x", __func__, ipi); cpu_ops.ipi_vectored(ipi, APIC_IPI_DEST_OTHERS); } int ipi_nmi_handler() { u_int cpuid; /* * As long as there is not a simple way to know about a NMI's * source, if the bitmask for the current CPU is present in * the global pending bitword an IPI_STOP_HARD has been issued * and should be handled. */ cpuid = PCPU_GET(cpuid); if (!CPU_ISSET(cpuid, &ipi_nmi_pending)) return (1); CPU_CLR_ATOMIC(cpuid, &ipi_nmi_pending); cpustop_handler(); return (0); } /* * Handle an IPI_STOP by saving our current context and spinning until we * are resumed. */ void cpustop_handler(void) { u_int cpu; cpu = PCPU_GET(cpuid); savectx(&stoppcbs[cpu]); /* Indicate that we are stopped */ CPU_SET_ATOMIC(cpu, &stopped_cpus); /* Wait for restart */ while (!CPU_ISSET(cpu, &started_cpus)) ia32_pause(); CPU_CLR_ATOMIC(cpu, &started_cpus); CPU_CLR_ATOMIC(cpu, &stopped_cpus); if (cpu == 0 && cpustop_restartfunc != NULL) { cpustop_restartfunc(); cpustop_restartfunc = NULL; } } /* * Handle an IPI_SUSPEND by saving our current context and spinning until we * are resumed. */ void cpususpend_handler(void) { u_int cpu; mtx_assert(&smp_ipi_mtx, MA_NOTOWNED); cpu = PCPU_GET(cpuid); if (savectx(&susppcbs[cpu]->sp_pcb)) { npxsuspend(susppcbs[cpu]->sp_fpususpend); wbinvd(); CPU_SET_ATOMIC(cpu, &suspended_cpus); } else { npxresume(susppcbs[cpu]->sp_fpususpend); pmap_init_pat(); initializecpu(); PCPU_SET(switchtime, 0); PCPU_SET(switchticks, ticks); /* Indicate that we are resumed */ CPU_CLR_ATOMIC(cpu, &suspended_cpus); } /* Wait for resume */ while (!CPU_ISSET(cpu, &started_cpus)) ia32_pause(); if (cpu_ops.cpu_resume) cpu_ops.cpu_resume(); /* Resume MCA and local APIC */ mca_resume(); lapic_setup(0); /* Indicate that we are resumed */ CPU_CLR_ATOMIC(cpu, &suspended_cpus); CPU_CLR_ATOMIC(cpu, &started_cpus); } /* * Handlers for TLB related IPIs */ void invltlb_handler(void) { uint64_t cr3; #ifdef COUNT_XINVLTLB_HITS xhits_gbl[PCPU_GET(cpuid)]++; #endif /* COUNT_XINVLTLB_HITS */ #ifdef COUNT_IPIS (*ipi_invltlb_counts[PCPU_GET(cpuid)])++; #endif /* COUNT_IPIS */ cr3 = rcr3(); load_cr3(cr3); atomic_add_int(&smp_tlb_wait, 1); } void invlpg_handler(void) { #ifdef COUNT_XINVLTLB_HITS xhits_pg[PCPU_GET(cpuid)]++; #endif /* COUNT_XINVLTLB_HITS */ #ifdef COUNT_IPIS (*ipi_invlpg_counts[PCPU_GET(cpuid)])++; #endif /* COUNT_IPIS */ invlpg(smp_tlb_addr1); atomic_add_int(&smp_tlb_wait, 1); } void invlrng_handler(void) { vm_offset_t addr; #ifdef COUNT_XINVLTLB_HITS xhits_rng[PCPU_GET(cpuid)]++; #endif /* COUNT_XINVLTLB_HITS */ #ifdef COUNT_IPIS (*ipi_invlrng_counts[PCPU_GET(cpuid)])++; #endif /* COUNT_IPIS */ addr = smp_tlb_addr1; do { invlpg(addr); addr += PAGE_SIZE; } while (addr < smp_tlb_addr2); atomic_add_int(&smp_tlb_wait, 1); } void invlcache_handler(void) { #ifdef COUNT_IPIS (*ipi_invlcache_counts[PCPU_GET(cpuid)])++; #endif /* COUNT_IPIS */ wbinvd(); atomic_add_int(&smp_tlb_wait, 1); } /* * This is called once the rest of the system is up and running and we're * ready to let the AP's out of the pen. */ static void release_aps(void *dummy __unused) { if (mp_ncpus == 1) return; atomic_store_rel_int(&aps_ready, 1); while (smp_started == 0) ia32_pause(); } SYSINIT(start_aps, SI_SUB_SMP, SI_ORDER_FIRST, release_aps, NULL); #ifdef COUNT_IPIS /* * Setup interrupt counters for IPI handlers. */ static void mp_ipi_intrcnt(void *dummy) { char buf[64]; int i; CPU_FOREACH(i) { snprintf(buf, sizeof(buf), "cpu%d:invltlb", i); intrcnt_add(buf, &ipi_invltlb_counts[i]); snprintf(buf, sizeof(buf), "cpu%d:invlrng", i); intrcnt_add(buf, &ipi_invlrng_counts[i]); snprintf(buf, sizeof(buf), "cpu%d:invlpg", i); intrcnt_add(buf, &ipi_invlpg_counts[i]); snprintf(buf, sizeof(buf), "cpu%d:invlcache", i); intrcnt_add(buf, &ipi_invlcache_counts[i]); snprintf(buf, sizeof(buf), "cpu%d:preempt", i); intrcnt_add(buf, &ipi_preempt_counts[i]); snprintf(buf, sizeof(buf), "cpu%d:ast", i); intrcnt_add(buf, &ipi_ast_counts[i]); snprintf(buf, sizeof(buf), "cpu%d:rendezvous", i); intrcnt_add(buf, &ipi_rendezvous_counts[i]); snprintf(buf, sizeof(buf), "cpu%d:lazypmap", i); intrcnt_add(buf, &ipi_lazypmap_counts[i]); snprintf(buf, sizeof(buf), "cpu%d:hardclock", i); intrcnt_add(buf, &ipi_hardclock_counts[i]); } } SYSINIT(mp_ipi_intrcnt, SI_SUB_INTR, SI_ORDER_MIDDLE, mp_ipi_intrcnt, NULL); #endif Index: stable/10/sys/x86/x86/local_apic.c =================================================================== --- stable/10/sys/x86/x86/local_apic.c (revision 281559) +++ stable/10/sys/x86/x86/local_apic.c (revision 281560) @@ -1,1515 +1,1515 @@ /*- * Copyright (c) 2003 John Baldwin * Copyright (c) 1996, by Steve Passe * All rights reserved. * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * 1. Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * 2. The name of the developer may NOT be used to endorse or promote products * derived from this software without specific prior written permission. * 3. Neither the name of the author nor the names of any co-contributors * may be used to endorse or promote products derived from this software * without specific prior written permission. * * THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE * ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF * SUCH DAMAGE. */ /* * Local APIC support on Pentium and later processors. */ #include __FBSDID("$FreeBSD$"); #include "opt_atpic.h" #include "opt_hwpmc_hooks.h" #include "opt_kdtrace.h" #include "opt_ddb.h" #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #ifdef DDB #include #include #endif #ifdef __amd64__ #define SDT_APIC SDT_SYSIGT #define SDT_APICT SDT_SYSIGT #define GSEL_APIC 0 #else #define SDT_APIC SDT_SYS386IGT #define SDT_APICT SDT_SYS386TGT #define GSEL_APIC GSEL(GCODE_SEL, SEL_KPL) #endif /* Sanity checks on IDT vectors. */ CTASSERT(APIC_IO_INTS + APIC_NUM_IOINTS == APIC_TIMER_INT); CTASSERT(APIC_TIMER_INT < APIC_LOCAL_INTS); CTASSERT(APIC_LOCAL_INTS == 240); CTASSERT(IPI_STOP < APIC_SPURIOUS_INT); /* Magic IRQ values for the timer and syscalls. */ #define IRQ_TIMER (NUM_IO_INTS + 1) #define IRQ_SYSCALL (NUM_IO_INTS + 2) #define IRQ_DTRACE_RET (NUM_IO_INTS + 3) #define IRQ_EVTCHN (NUM_IO_INTS + 4) /* * Support for local APICs. Local APICs manage interrupts on each * individual processor as opposed to I/O APICs which receive interrupts * from I/O devices and then forward them on to the local APICs. * * Local APICs can also send interrupts to each other thus providing the * mechanism for IPIs. */ struct lvt { u_int lvt_edgetrigger:1; u_int lvt_activehi:1; u_int lvt_masked:1; u_int lvt_active:1; u_int lvt_mode:16; u_int lvt_vector:8; }; struct lapic { struct lvt la_lvts[APIC_LVT_MAX + 1]; u_int la_id:8; u_int la_cluster:4; u_int la_cluster_id:2; u_int la_present:1; u_long *la_timer_count; u_long la_timer_period; u_int la_timer_mode; uint32_t lvt_timer_cache; /* Include IDT_SYSCALL to make indexing easier. */ int la_ioint_irqs[APIC_NUM_IOINTS + 1]; } static lapics[MAX_APIC_ID + 1]; /* Global defaults for local APIC LVT entries. */ static struct lvt lvts[APIC_LVT_MAX + 1] = { { 1, 1, 1, 1, APIC_LVT_DM_EXTINT, 0 }, /* LINT0: masked ExtINT */ { 1, 1, 0, 1, APIC_LVT_DM_NMI, 0 }, /* LINT1: NMI */ { 1, 1, 1, 1, APIC_LVT_DM_FIXED, APIC_TIMER_INT }, /* Timer */ { 1, 1, 0, 1, APIC_LVT_DM_FIXED, APIC_ERROR_INT }, /* Error */ { 1, 1, 1, 1, APIC_LVT_DM_NMI, 0 }, /* PMC */ { 1, 1, 1, 1, APIC_LVT_DM_FIXED, APIC_THERMAL_INT }, /* Thermal */ { 1, 1, 1, 1, APIC_LVT_DM_FIXED, APIC_CMC_INT }, /* CMCI */ }; static inthand_t *ioint_handlers[] = { NULL, /* 0 - 31 */ IDTVEC(apic_isr1), /* 32 - 63 */ IDTVEC(apic_isr2), /* 64 - 95 */ IDTVEC(apic_isr3), /* 96 - 127 */ IDTVEC(apic_isr4), /* 128 - 159 */ IDTVEC(apic_isr5), /* 160 - 191 */ IDTVEC(apic_isr6), /* 192 - 223 */ IDTVEC(apic_isr7), /* 224 - 255 */ }; static u_int32_t lapic_timer_divisors[] = { APIC_TDCR_1, APIC_TDCR_2, APIC_TDCR_4, APIC_TDCR_8, APIC_TDCR_16, APIC_TDCR_32, APIC_TDCR_64, APIC_TDCR_128 }; extern inthand_t IDTVEC(rsvd); volatile lapic_t *lapic; vm_paddr_t lapic_paddr; static u_long lapic_timer_divisor; static struct eventtimer lapic_et; static void lapic_enable(void); static void lapic_resume(struct pic *pic, bool suspend_cancelled); static void lapic_timer_oneshot(struct lapic *, u_int count, int enable_int); static void lapic_timer_periodic(struct lapic *, u_int count, int enable_int); static void lapic_timer_stop(struct lapic *); static void lapic_timer_set_divisor(u_int divisor); static uint32_t lvt_mode(struct lapic *la, u_int pin, uint32_t value); static int lapic_et_start(struct eventtimer *et, sbintime_t first, sbintime_t period); static int lapic_et_stop(struct eventtimer *et); struct pic lapic_pic = { .pic_resume = lapic_resume }; static uint32_t lvt_mode(struct lapic *la, u_int pin, uint32_t value) { struct lvt *lvt; KASSERT(pin <= APIC_LVT_MAX, ("%s: pin %u out of range", __func__, pin)); if (la->la_lvts[pin].lvt_active) lvt = &la->la_lvts[pin]; else lvt = &lvts[pin]; value &= ~(APIC_LVT_M | APIC_LVT_TM | APIC_LVT_IIPP | APIC_LVT_DM | APIC_LVT_VECTOR); if (lvt->lvt_edgetrigger == 0) value |= APIC_LVT_TM; if (lvt->lvt_activehi == 0) value |= APIC_LVT_IIPP_INTALO; if (lvt->lvt_masked) value |= APIC_LVT_M; value |= lvt->lvt_mode; switch (lvt->lvt_mode) { case APIC_LVT_DM_NMI: case APIC_LVT_DM_SMI: case APIC_LVT_DM_INIT: case APIC_LVT_DM_EXTINT: if (!lvt->lvt_edgetrigger) { printf("lapic%u: Forcing LINT%u to edge trigger\n", la->la_id, pin); value |= APIC_LVT_TM; } /* Use a vector of 0. */ break; case APIC_LVT_DM_FIXED: value |= lvt->lvt_vector; break; default: panic("bad APIC LVT delivery mode: %#x\n", value); } return (value); } /* * Map the local APIC and setup necessary interrupt vectors. */ void lapic_init(vm_paddr_t addr) { u_int regs[4]; int i, arat; /* Map the local APIC and setup the spurious interrupt handler. */ KASSERT(trunc_page(addr) == addr, ("local APIC not aligned on a page boundary")); lapic_paddr = addr; lapic = pmap_mapdev(addr, sizeof(lapic_t)); setidt(APIC_SPURIOUS_INT, IDTVEC(spuriousint), SDT_APIC, SEL_KPL, GSEL_APIC); /* Perform basic initialization of the BSP's local APIC. */ lapic_enable(); /* Set BSP's per-CPU local APIC ID. */ PCPU_SET(apic_id, lapic_id()); /* Local APIC timer interrupt. */ setidt(APIC_TIMER_INT, IDTVEC(timerint), SDT_APIC, SEL_KPL, GSEL_APIC); /* Local APIC error interrupt. */ setidt(APIC_ERROR_INT, IDTVEC(errorint), SDT_APIC, SEL_KPL, GSEL_APIC); /* XXX: Thermal interrupt */ /* Local APIC CMCI. */ setidt(APIC_CMC_INT, IDTVEC(cmcint), SDT_APICT, SEL_KPL, GSEL_APIC); if ((resource_int_value("apic", 0, "clock", &i) != 0 || i != 0)) { arat = 0; /* Intel CPUID 0x06 EAX[2] set if APIC timer runs in C3. */ if (cpu_vendor_id == CPU_VENDOR_INTEL && cpu_high >= 6) { do_cpuid(0x06, regs); if ((regs[0] & CPUTPM1_ARAT) != 0) arat = 1; } bzero(&lapic_et, sizeof(lapic_et)); lapic_et.et_name = "LAPIC"; lapic_et.et_flags = ET_FLAGS_PERIODIC | ET_FLAGS_ONESHOT | ET_FLAGS_PERCPU; lapic_et.et_quality = 600; if (!arat) { lapic_et.et_flags |= ET_FLAGS_C3STOP; lapic_et.et_quality -= 200; } lapic_et.et_frequency = 0; /* We don't know frequency yet, so trying to guess. */ lapic_et.et_min_period = 0x00001000LL; lapic_et.et_max_period = SBT_1S; lapic_et.et_start = lapic_et_start; lapic_et.et_stop = lapic_et_stop; lapic_et.et_priv = NULL; et_register(&lapic_et); } } /* * Create a local APIC instance. */ void lapic_create(u_int apic_id, int boot_cpu) { int i; if (apic_id > MAX_APIC_ID) { printf("APIC: Ignoring local APIC with ID %d\n", apic_id); if (boot_cpu) panic("Can't ignore BSP"); return; } KASSERT(!lapics[apic_id].la_present, ("duplicate local APIC %u", apic_id)); /* * Assume no local LVT overrides and a cluster of 0 and * intra-cluster ID of 0. */ lapics[apic_id].la_present = 1; lapics[apic_id].la_id = apic_id; for (i = 0; i <= APIC_LVT_MAX; i++) { lapics[apic_id].la_lvts[i] = lvts[i]; lapics[apic_id].la_lvts[i].lvt_active = 0; } for (i = 0; i <= APIC_NUM_IOINTS; i++) lapics[apic_id].la_ioint_irqs[i] = -1; lapics[apic_id].la_ioint_irqs[IDT_SYSCALL - APIC_IO_INTS] = IRQ_SYSCALL; lapics[apic_id].la_ioint_irqs[APIC_TIMER_INT - APIC_IO_INTS] = IRQ_TIMER; #ifdef KDTRACE_HOOKS lapics[apic_id].la_ioint_irqs[IDT_DTRACE_RET - APIC_IO_INTS] = IRQ_DTRACE_RET; #endif #ifdef XENHVM lapics[apic_id].la_ioint_irqs[IDT_EVTCHN - APIC_IO_INTS] = IRQ_EVTCHN; #endif #ifdef SMP cpu_add(apic_id, boot_cpu); #endif } /* * Dump contents of local APIC registers */ void lapic_dump(const char* str) { uint32_t maxlvt; maxlvt = (lapic->version & APIC_VER_MAXLVT) >> MAXLVTSHIFT; printf("cpu%d %s:\n", PCPU_GET(cpuid), str); printf(" ID: 0x%08x VER: 0x%08x LDR: 0x%08x DFR: 0x%08x\n", lapic->id, lapic->version, lapic->ldr, lapic->dfr); printf(" lint0: 0x%08x lint1: 0x%08x TPR: 0x%08x SVR: 0x%08x\n", lapic->lvt_lint0, lapic->lvt_lint1, lapic->tpr, lapic->svr); printf(" timer: 0x%08x therm: 0x%08x err: 0x%08x", lapic->lvt_timer, lapic->lvt_thermal, lapic->lvt_error); if (maxlvt >= APIC_LVT_PMC) printf(" pmc: 0x%08x", lapic->lvt_pcint); printf("\n"); if (maxlvt >= APIC_LVT_CMCI) printf(" cmci: 0x%08x\n", lapic->lvt_cmci); } void lapic_setup(int boot) { struct lapic *la; u_int32_t maxlvt; register_t saveintr; char buf[MAXCOMLEN + 1]; la = &lapics[lapic_id()]; KASSERT(la->la_present, ("missing APIC structure")); saveintr = intr_disable(); maxlvt = (lapic->version & APIC_VER_MAXLVT) >> MAXLVTSHIFT; /* Initialize the TPR to allow all interrupts. */ lapic_set_tpr(0); /* Setup spurious vector and enable the local APIC. */ lapic_enable(); /* Program LINT[01] LVT entries. */ lapic->lvt_lint0 = lvt_mode(la, APIC_LVT_LINT0, lapic->lvt_lint0); lapic->lvt_lint1 = lvt_mode(la, APIC_LVT_LINT1, lapic->lvt_lint1); /* Program the PMC LVT entry if present. */ if (maxlvt >= APIC_LVT_PMC) lapic->lvt_pcint = lvt_mode(la, APIC_LVT_PMC, lapic->lvt_pcint); /* Program timer LVT and setup handler. */ la->lvt_timer_cache = lapic->lvt_timer = lvt_mode(la, APIC_LVT_TIMER, lapic->lvt_timer); if (boot) { snprintf(buf, sizeof(buf), "cpu%d:timer", PCPU_GET(cpuid)); intrcnt_add(buf, &la->la_timer_count); } /* Setup the timer if configured. */ if (la->la_timer_mode != 0) { KASSERT(la->la_timer_period != 0, ("lapic%u: zero divisor", lapic_id())); lapic_timer_set_divisor(lapic_timer_divisor); if (la->la_timer_mode == 1) lapic_timer_periodic(la, la->la_timer_period, 1); else lapic_timer_oneshot(la, la->la_timer_period, 1); } /* Program error LVT and clear any existing errors. */ lapic->lvt_error = lvt_mode(la, APIC_LVT_ERROR, lapic->lvt_error); lapic->esr = 0; /* XXX: Thermal LVT */ /* Program the CMCI LVT entry if present. */ if (maxlvt >= APIC_LVT_CMCI) lapic->lvt_cmci = lvt_mode(la, APIC_LVT_CMCI, lapic->lvt_cmci); intr_restore(saveintr); } void lapic_reenable_pmc(void) { #ifdef HWPMC_HOOKS uint32_t value; value = lapic->lvt_pcint; value &= ~APIC_LVT_M; lapic->lvt_pcint = value; #endif } #ifdef HWPMC_HOOKS static void lapic_update_pmc(void *dummy) { struct lapic *la; la = &lapics[lapic_id()]; lapic->lvt_pcint = lvt_mode(la, APIC_LVT_PMC, lapic->lvt_pcint); } #endif int lapic_enable_pmc(void) { #ifdef HWPMC_HOOKS u_int32_t maxlvt; /* Fail if the local APIC is not present. */ if (lapic == NULL) return (0); /* Fail if the PMC LVT is not present. */ maxlvt = (lapic->version & APIC_VER_MAXLVT) >> MAXLVTSHIFT; if (maxlvt < APIC_LVT_PMC) return (0); lvts[APIC_LVT_PMC].lvt_masked = 0; #ifdef SMP /* * If hwpmc was loaded at boot time then the APs may not be * started yet. In that case, don't forward the request to * them as they will program the lvt when they start. */ if (smp_started) smp_rendezvous(NULL, lapic_update_pmc, NULL, NULL); else #endif lapic_update_pmc(NULL); return (1); #else return (0); #endif } void lapic_disable_pmc(void) { #ifdef HWPMC_HOOKS u_int32_t maxlvt; /* Fail if the local APIC is not present. */ if (lapic == NULL) return; /* Fail if the PMC LVT is not present. */ maxlvt = (lapic->version & APIC_VER_MAXLVT) >> MAXLVTSHIFT; if (maxlvt < APIC_LVT_PMC) return; lvts[APIC_LVT_PMC].lvt_masked = 1; #ifdef SMP /* The APs should always be started when hwpmc is unloaded. */ KASSERT(mp_ncpus == 1 || smp_started, ("hwpmc unloaded too early")); #endif smp_rendezvous(NULL, lapic_update_pmc, NULL, NULL); #endif } static int lapic_et_start(struct eventtimer *et, sbintime_t first, sbintime_t period) { struct lapic *la; u_long value; la = &lapics[PCPU_GET(apic_id)]; if (et->et_frequency == 0) { /* Start off with a divisor of 2 (power on reset default). */ lapic_timer_divisor = 2; /* Try to calibrate the local APIC timer. */ do { lapic_timer_set_divisor(lapic_timer_divisor); lapic_timer_oneshot(la, APIC_TIMER_MAX_COUNT, 0); DELAY(1000000); value = APIC_TIMER_MAX_COUNT - lapic->ccr_timer; if (value != APIC_TIMER_MAX_COUNT) break; lapic_timer_divisor <<= 1; } while (lapic_timer_divisor <= 128); if (lapic_timer_divisor > 128) panic("lapic: Divisor too big"); if (bootverbose) printf("lapic: Divisor %lu, Frequency %lu Hz\n", lapic_timer_divisor, value); et->et_frequency = value; et->et_min_period = (0x00000002LLU << 32) / et->et_frequency; et->et_max_period = (0xfffffffeLLU << 32) / et->et_frequency; } if (la->la_timer_mode == 0) lapic_timer_set_divisor(lapic_timer_divisor); if (period != 0) { la->la_timer_mode = 1; la->la_timer_period = ((uint32_t)et->et_frequency * period) >> 32; lapic_timer_periodic(la, la->la_timer_period, 1); } else { la->la_timer_mode = 2; la->la_timer_period = ((uint32_t)et->et_frequency * first) >> 32; lapic_timer_oneshot(la, la->la_timer_period, 1); } return (0); } static int lapic_et_stop(struct eventtimer *et) { struct lapic *la = &lapics[PCPU_GET(apic_id)]; la->la_timer_mode = 0; lapic_timer_stop(la); return (0); } void lapic_disable(void) { uint32_t value; /* Software disable the local APIC. */ value = lapic->svr; value &= ~APIC_SVR_SWEN; lapic->svr = value; } static void lapic_enable(void) { u_int32_t value; /* Program the spurious vector to enable the local APIC. */ value = lapic->svr; value &= ~(APIC_SVR_VECTOR | APIC_SVR_FOCUS); value |= (APIC_SVR_FEN | APIC_SVR_SWEN | APIC_SPURIOUS_INT); lapic->svr = value; } /* Reset the local APIC on the BSP during resume. */ static void lapic_resume(struct pic *pic, bool suspend_cancelled) { lapic_setup(0); } int lapic_id(void) { KASSERT(lapic != NULL, ("local APIC is not mapped")); return (lapic->id >> APIC_ID_SHIFT); } int lapic_intr_pending(u_int vector) { volatile u_int32_t *irr; /* * The IRR registers are an array of 128-bit registers each of * which only describes 32 interrupts in the low 32 bits.. Thus, * we divide the vector by 32 to get the 128-bit index. We then * multiply that index by 4 to get the equivalent index from * treating the IRR as an array of 32-bit registers. Finally, we * modulus the vector by 32 to determine the individual bit to * test. */ irr = &lapic->irr0; return (irr[(vector / 32) * 4] & 1 << (vector % 32)); } void lapic_set_logical_id(u_int apic_id, u_int cluster, u_int cluster_id) { struct lapic *la; KASSERT(lapics[apic_id].la_present, ("%s: APIC %u doesn't exist", __func__, apic_id)); KASSERT(cluster <= APIC_MAX_CLUSTER, ("%s: cluster %u too big", __func__, cluster)); KASSERT(cluster_id <= APIC_MAX_INTRACLUSTER_ID, ("%s: intra cluster id %u too big", __func__, cluster_id)); la = &lapics[apic_id]; la->la_cluster = cluster; la->la_cluster_id = cluster_id; } int lapic_set_lvt_mask(u_int apic_id, u_int pin, u_char masked) { if (pin > APIC_LVT_MAX) return (EINVAL); if (apic_id == APIC_ID_ALL) { lvts[pin].lvt_masked = masked; if (bootverbose) printf("lapic:"); } else { KASSERT(lapics[apic_id].la_present, ("%s: missing APIC %u", __func__, apic_id)); lapics[apic_id].la_lvts[pin].lvt_masked = masked; lapics[apic_id].la_lvts[pin].lvt_active = 1; if (bootverbose) printf("lapic%u:", apic_id); } if (bootverbose) printf(" LINT%u %s\n", pin, masked ? "masked" : "unmasked"); return (0); } int lapic_set_lvt_mode(u_int apic_id, u_int pin, u_int32_t mode) { struct lvt *lvt; if (pin > APIC_LVT_MAX) return (EINVAL); if (apic_id == APIC_ID_ALL) { lvt = &lvts[pin]; if (bootverbose) printf("lapic:"); } else { KASSERT(lapics[apic_id].la_present, ("%s: missing APIC %u", __func__, apic_id)); lvt = &lapics[apic_id].la_lvts[pin]; lvt->lvt_active = 1; if (bootverbose) printf("lapic%u:", apic_id); } lvt->lvt_mode = mode; switch (mode) { case APIC_LVT_DM_NMI: case APIC_LVT_DM_SMI: case APIC_LVT_DM_INIT: case APIC_LVT_DM_EXTINT: lvt->lvt_edgetrigger = 1; lvt->lvt_activehi = 1; if (mode == APIC_LVT_DM_EXTINT) lvt->lvt_masked = 1; else lvt->lvt_masked = 0; break; default: panic("Unsupported delivery mode: 0x%x\n", mode); } if (bootverbose) { printf(" Routing "); switch (mode) { case APIC_LVT_DM_NMI: printf("NMI"); break; case APIC_LVT_DM_SMI: printf("SMI"); break; case APIC_LVT_DM_INIT: printf("INIT"); break; case APIC_LVT_DM_EXTINT: printf("ExtINT"); break; } printf(" -> LINT%u\n", pin); } return (0); } int lapic_set_lvt_polarity(u_int apic_id, u_int pin, enum intr_polarity pol) { if (pin > APIC_LVT_MAX || pol == INTR_POLARITY_CONFORM) return (EINVAL); if (apic_id == APIC_ID_ALL) { lvts[pin].lvt_activehi = (pol == INTR_POLARITY_HIGH); if (bootverbose) printf("lapic:"); } else { KASSERT(lapics[apic_id].la_present, ("%s: missing APIC %u", __func__, apic_id)); lapics[apic_id].la_lvts[pin].lvt_active = 1; lapics[apic_id].la_lvts[pin].lvt_activehi = (pol == INTR_POLARITY_HIGH); if (bootverbose) printf("lapic%u:", apic_id); } if (bootverbose) printf(" LINT%u polarity: %s\n", pin, pol == INTR_POLARITY_HIGH ? "high" : "low"); return (0); } int lapic_set_lvt_triggermode(u_int apic_id, u_int pin, enum intr_trigger trigger) { if (pin > APIC_LVT_MAX || trigger == INTR_TRIGGER_CONFORM) return (EINVAL); if (apic_id == APIC_ID_ALL) { lvts[pin].lvt_edgetrigger = (trigger == INTR_TRIGGER_EDGE); if (bootverbose) printf("lapic:"); } else { KASSERT(lapics[apic_id].la_present, ("%s: missing APIC %u", __func__, apic_id)); lapics[apic_id].la_lvts[pin].lvt_edgetrigger = (trigger == INTR_TRIGGER_EDGE); lapics[apic_id].la_lvts[pin].lvt_active = 1; if (bootverbose) printf("lapic%u:", apic_id); } if (bootverbose) printf(" LINT%u trigger: %s\n", pin, trigger == INTR_TRIGGER_EDGE ? "edge" : "level"); return (0); } /* * Adjust the TPR of the current CPU so that it blocks all interrupts below * the passed in vector. */ void lapic_set_tpr(u_int vector) { #ifdef CHEAP_TPR lapic->tpr = vector; #else u_int32_t tpr; tpr = lapic->tpr & ~APIC_TPR_PRIO; tpr |= vector; lapic->tpr = tpr; #endif } void lapic_eoi(void) { lapic->eoi = 0; } void lapic_handle_intr(int vector, struct trapframe *frame) { struct intsrc *isrc; isrc = intr_lookup_source(apic_idt_to_irq(PCPU_GET(apic_id), vector)); intr_execute_handlers(isrc, frame); } void lapic_handle_timer(struct trapframe *frame) { struct lapic *la; struct trapframe *oldframe; struct thread *td; /* Send EOI first thing. */ lapic_eoi(); #if defined(SMP) && !defined(SCHED_ULE) /* * Don't do any accounting for the disabled HTT cores, since it * will provide misleading numbers for the userland. * * No locking is necessary here, since even if we lose the race * when hlt_cpus_mask changes it is not a big deal, really. * * Don't do that for ULE, since ULE doesn't consider hlt_cpus_mask * and unlike other schedulers it actually schedules threads to * those CPUs. */ if (CPU_ISSET(PCPU_GET(cpuid), &hlt_cpus_mask)) return; #endif /* Look up our local APIC structure for the tick counters. */ la = &lapics[PCPU_GET(apic_id)]; (*la->la_timer_count)++; critical_enter(); if (lapic_et.et_active) { td = curthread; td->td_intr_nesting_level++; oldframe = td->td_intr_frame; td->td_intr_frame = frame; lapic_et.et_event_cb(&lapic_et, lapic_et.et_arg); td->td_intr_frame = oldframe; td->td_intr_nesting_level--; } critical_exit(); } static void lapic_timer_set_divisor(u_int divisor) { KASSERT(powerof2(divisor), ("lapic: invalid divisor %u", divisor)); KASSERT(ffs(divisor) <= sizeof(lapic_timer_divisors) / sizeof(u_int32_t), ("lapic: invalid divisor %u", divisor)); lapic->dcr_timer = lapic_timer_divisors[ffs(divisor) - 1]; } static void lapic_timer_oneshot(struct lapic *la, u_int count, int enable_int) { u_int32_t value; value = la->lvt_timer_cache; value &= ~APIC_LVTT_TM; value |= APIC_LVTT_TM_ONE_SHOT; if (enable_int) value &= ~APIC_LVT_M; lapic->lvt_timer = value; lapic->icr_timer = count; } static void lapic_timer_periodic(struct lapic *la, u_int count, int enable_int) { u_int32_t value; value = la->lvt_timer_cache; value &= ~APIC_LVTT_TM; value |= APIC_LVTT_TM_PERIODIC; if (enable_int) value &= ~APIC_LVT_M; lapic->lvt_timer = value; lapic->icr_timer = count; } static void lapic_timer_stop(struct lapic *la) { u_int32_t value; value = la->lvt_timer_cache; value &= ~APIC_LVTT_TM; value |= APIC_LVT_M; lapic->lvt_timer = value; } void lapic_handle_cmc(void) { lapic_eoi(); cmc_intr(); } /* * Called from the mca_init() to activate the CMC interrupt if this CPU is * responsible for monitoring any MC banks for CMC events. Since mca_init() * is called prior to lapic_setup() during boot, this just needs to unmask * this CPU's LVT_CMCI entry. */ void lapic_enable_cmc(void) { u_int apic_id; #ifdef DEV_ATPIC if (lapic == NULL) return; #endif apic_id = PCPU_GET(apic_id); KASSERT(lapics[apic_id].la_present, ("%s: missing APIC %u", __func__, apic_id)); lapics[apic_id].la_lvts[APIC_LVT_CMCI].lvt_masked = 0; lapics[apic_id].la_lvts[APIC_LVT_CMCI].lvt_active = 1; if (bootverbose) printf("lapic%u: CMCI unmasked\n", apic_id); } void lapic_handle_error(void) { u_int32_t esr; /* * Read the contents of the error status register. Write to * the register first before reading from it to force the APIC * to update its value to indicate any errors that have * occurred since the previous write to the register. */ lapic->esr = 0; esr = lapic->esr; printf("CPU%d: local APIC error 0x%x\n", PCPU_GET(cpuid), esr); lapic_eoi(); } u_int apic_cpuid(u_int apic_id) { #ifdef SMP return apic_cpuids[apic_id]; #else return 0; #endif } /* Request a free IDT vector to be used by the specified IRQ. */ u_int apic_alloc_vector(u_int apic_id, u_int irq) { u_int vector; KASSERT(irq < NUM_IO_INTS, ("Invalid IRQ %u", irq)); /* * Search for a free vector. Currently we just use a very simple * algorithm to find the first free vector. */ mtx_lock_spin(&icu_lock); for (vector = 0; vector < APIC_NUM_IOINTS; vector++) { if (lapics[apic_id].la_ioint_irqs[vector] != -1) continue; lapics[apic_id].la_ioint_irqs[vector] = irq; mtx_unlock_spin(&icu_lock); return (vector + APIC_IO_INTS); } mtx_unlock_spin(&icu_lock); return (0); } /* * Request 'count' free contiguous IDT vectors to be used by 'count' * IRQs. 'count' must be a power of two and the vectors will be * aligned on a boundary of 'align'. If the request cannot be * satisfied, 0 is returned. */ u_int apic_alloc_vectors(u_int apic_id, u_int *irqs, u_int count, u_int align) { u_int first, run, vector; KASSERT(powerof2(count), ("bad count")); KASSERT(powerof2(align), ("bad align")); KASSERT(align >= count, ("align < count")); #ifdef INVARIANTS for (run = 0; run < count; run++) KASSERT(irqs[run] < NUM_IO_INTS, ("Invalid IRQ %u at index %u", irqs[run], run)); #endif /* * Search for 'count' free vectors. As with apic_alloc_vector(), * this just uses a simple first fit algorithm. */ run = 0; first = 0; mtx_lock_spin(&icu_lock); for (vector = 0; vector < APIC_NUM_IOINTS; vector++) { /* Vector is in use, end run. */ if (lapics[apic_id].la_ioint_irqs[vector] != -1) { run = 0; first = 0; continue; } /* Start a new run if run == 0 and vector is aligned. */ if (run == 0) { if ((vector & (align - 1)) != 0) continue; first = vector; } run++; /* Keep looping if the run isn't long enough yet. */ if (run < count) continue; /* Found a run, assign IRQs and return the first vector. */ for (vector = 0; vector < count; vector++) lapics[apic_id].la_ioint_irqs[first + vector] = irqs[vector]; mtx_unlock_spin(&icu_lock); return (first + APIC_IO_INTS); } mtx_unlock_spin(&icu_lock); printf("APIC: Couldn't find APIC vectors for %u IRQs\n", count); return (0); } /* * Enable a vector for a particular apic_id. Since all lapics share idt * entries and ioint_handlers this enables the vector on all lapics. lapics * which do not have the vector configured would report spurious interrupts * should it fire. */ void apic_enable_vector(u_int apic_id, u_int vector) { KASSERT(vector != IDT_SYSCALL, ("Attempt to overwrite syscall entry")); KASSERT(ioint_handlers[vector / 32] != NULL, ("No ISR handler for vector %u", vector)); #ifdef KDTRACE_HOOKS KASSERT(vector != IDT_DTRACE_RET, ("Attempt to overwrite DTrace entry")); #endif setidt(vector, ioint_handlers[vector / 32], SDT_APIC, SEL_KPL, GSEL_APIC); } void apic_disable_vector(u_int apic_id, u_int vector) { KASSERT(vector != IDT_SYSCALL, ("Attempt to overwrite syscall entry")); #ifdef KDTRACE_HOOKS KASSERT(vector != IDT_DTRACE_RET, ("Attempt to overwrite DTrace entry")); #endif KASSERT(ioint_handlers[vector / 32] != NULL, ("No ISR handler for vector %u", vector)); #ifdef notyet /* * We can not currently clear the idt entry because other cpus * may have a valid vector at this offset. */ setidt(vector, &IDTVEC(rsvd), SDT_APICT, SEL_KPL, GSEL_APIC); #endif } /* Release an APIC vector when it's no longer in use. */ void apic_free_vector(u_int apic_id, u_int vector, u_int irq) { struct thread *td; KASSERT(vector >= APIC_IO_INTS && vector != IDT_SYSCALL && vector <= APIC_IO_INTS + APIC_NUM_IOINTS, ("Vector %u does not map to an IRQ line", vector)); KASSERT(irq < NUM_IO_INTS, ("Invalid IRQ %u", irq)); KASSERT(lapics[apic_id].la_ioint_irqs[vector - APIC_IO_INTS] == irq, ("IRQ mismatch")); #ifdef KDTRACE_HOOKS KASSERT(vector != IDT_DTRACE_RET, ("Attempt to overwrite DTrace entry")); #endif /* * Bind us to the cpu that owned the vector before freeing it so * we don't lose an interrupt delivery race. */ td = curthread; if (!rebooting) { thread_lock(td); if (sched_is_bound(td)) panic("apic_free_vector: Thread already bound.\n"); sched_bind(td, apic_cpuid(apic_id)); thread_unlock(td); } mtx_lock_spin(&icu_lock); lapics[apic_id].la_ioint_irqs[vector - APIC_IO_INTS] = -1; mtx_unlock_spin(&icu_lock); if (!rebooting) { thread_lock(td); sched_unbind(td); thread_unlock(td); } } /* Map an IDT vector (APIC) to an IRQ (interrupt source). */ u_int apic_idt_to_irq(u_int apic_id, u_int vector) { int irq; KASSERT(vector >= APIC_IO_INTS && vector != IDT_SYSCALL && vector <= APIC_IO_INTS + APIC_NUM_IOINTS, ("Vector %u does not map to an IRQ line", vector)); #ifdef KDTRACE_HOOKS KASSERT(vector != IDT_DTRACE_RET, ("Attempt to overwrite DTrace entry")); #endif irq = lapics[apic_id].la_ioint_irqs[vector - APIC_IO_INTS]; if (irq < 0) irq = 0; return (irq); } #ifdef DDB /* * Dump data about APIC IDT vector mappings. */ DB_SHOW_COMMAND(apic, db_show_apic) { struct intsrc *isrc; int i, verbose; u_int apic_id; u_int irq; if (strcmp(modif, "vv") == 0) verbose = 2; else if (strcmp(modif, "v") == 0) verbose = 1; else verbose = 0; for (apic_id = 0; apic_id <= MAX_APIC_ID; apic_id++) { if (lapics[apic_id].la_present == 0) continue; db_printf("Interrupts bound to lapic %u\n", apic_id); for (i = 0; i < APIC_NUM_IOINTS + 1 && !db_pager_quit; i++) { irq = lapics[apic_id].la_ioint_irqs[i]; if (irq == -1 || irq == IRQ_SYSCALL) continue; #ifdef KDTRACE_HOOKS if (irq == IRQ_DTRACE_RET) continue; #endif #ifdef XENHVM if (irq == IRQ_EVTCHN) continue; #endif db_printf("vec 0x%2x -> ", i + APIC_IO_INTS); if (irq == IRQ_TIMER) db_printf("lapic timer\n"); else if (irq < NUM_IO_INTS) { isrc = intr_lookup_source(irq); if (isrc == NULL || verbose == 0) db_printf("IRQ %u\n", irq); else db_dump_intr_event(isrc->is_event, verbose == 2); } else db_printf("IRQ %u ???\n", irq); } } } static void dump_mask(const char *prefix, uint32_t v, int base) { int i, first; first = 1; for (i = 0; i < 32; i++) if (v & (1 << i)) { if (first) { db_printf("%s:", prefix); first = 0; } db_printf(" %02x", base + i); } if (!first) db_printf("\n"); } /* Show info from the lapic regs for this CPU. */ DB_SHOW_COMMAND(lapic, db_show_lapic) { uint32_t v; db_printf("lapic ID = %d\n", lapic_id()); v = lapic->version; db_printf("version = %d.%d\n", (v & APIC_VER_VERSION) >> 4, v & 0xf); db_printf("max LVT = %d\n", (v & APIC_VER_MAXLVT) >> MAXLVTSHIFT); v = lapic->svr; db_printf("SVR = %02x (%s)\n", v & APIC_SVR_VECTOR, v & APIC_SVR_ENABLE ? "enabled" : "disabled"); db_printf("TPR = %02x\n", lapic->tpr); #define dump_field(prefix, index) \ dump_mask(__XSTRING(prefix ## index), lapic->prefix ## index, \ index * 32) db_printf("In-service Interrupts:\n"); dump_field(isr, 0); dump_field(isr, 1); dump_field(isr, 2); dump_field(isr, 3); dump_field(isr, 4); dump_field(isr, 5); dump_field(isr, 6); dump_field(isr, 7); db_printf("TMR Interrupts:\n"); dump_field(tmr, 0); dump_field(tmr, 1); dump_field(tmr, 2); dump_field(tmr, 3); dump_field(tmr, 4); dump_field(tmr, 5); dump_field(tmr, 6); dump_field(tmr, 7); db_printf("IRR Interrupts:\n"); dump_field(irr, 0); dump_field(irr, 1); dump_field(irr, 2); dump_field(irr, 3); dump_field(irr, 4); dump_field(irr, 5); dump_field(irr, 6); dump_field(irr, 7); #undef dump_field } #endif /* * APIC probing support code. This includes code to manage enumerators. */ static SLIST_HEAD(, apic_enumerator) enumerators = SLIST_HEAD_INITIALIZER(enumerators); static struct apic_enumerator *best_enum; void apic_register_enumerator(struct apic_enumerator *enumerator) { #ifdef INVARIANTS struct apic_enumerator *apic_enum; SLIST_FOREACH(apic_enum, &enumerators, apic_next) { if (apic_enum == enumerator) panic("%s: Duplicate register of %s", __func__, enumerator->apic_name); } #endif SLIST_INSERT_HEAD(&enumerators, enumerator, apic_next); } /* * We have to look for CPU's very, very early because certain subsystems * want to know how many CPU's we have extremely early on in the boot * process. */ static void apic_init(void *dummy __unused) { struct apic_enumerator *enumerator; int retval, best; /* We only support built in local APICs. */ if (!(cpu_feature & CPUID_APIC)) return; /* Don't probe if APIC mode is disabled. */ if (resource_disabled("apic", 0)) return; /* Probe all the enumerators to find the best match. */ best_enum = NULL; best = 0; SLIST_FOREACH(enumerator, &enumerators, apic_next) { retval = enumerator->apic_probe(); if (retval > 0) continue; if (best_enum == NULL || best < retval) { best_enum = enumerator; best = retval; } } if (best_enum == NULL) { if (bootverbose) printf("APIC: Could not find any APICs.\n"); #ifndef DEV_ATPIC panic("running without device atpic requires a local APIC"); #endif return; } if (bootverbose) printf("APIC: Using the %s enumerator.\n", best_enum->apic_name); #ifdef I686_CPU /* * To work around an errata, we disable the local APIC on some * CPUs during early startup. We need to turn the local APIC back * on on such CPUs now. */ ppro_reenable_apic(); #endif /* Probe the CPU's in the system. */ retval = best_enum->apic_probe_cpus(); if (retval != 0) printf("%s: Failed to probe CPUs: returned %d\n", best_enum->apic_name, retval); } SYSINIT(apic_init, SI_SUB_TUNABLES - 1, SI_ORDER_SECOND, apic_init, NULL); /* * Setup the local APIC. We have to do this prior to starting up the APs * in the SMP case. */ static void apic_setup_local(void *dummy __unused) { int retval; if (best_enum == NULL) return; /* Initialize the local APIC. */ retval = best_enum->apic_setup_local(); if (retval != 0) printf("%s: Failed to setup the local APIC: returned %d\n", best_enum->apic_name, retval); } SYSINIT(apic_setup_local, SI_SUB_CPU, SI_ORDER_SECOND, apic_setup_local, NULL); /* * Setup the I/O APICs. */ static void apic_setup_io(void *dummy __unused) { int retval; if (best_enum == NULL) return; /* * Local APIC must be registered before other PICs and pseudo PICs * for proper suspend/resume order. */ #ifndef XEN intr_register_pic(&lapic_pic); #endif retval = best_enum->apic_setup_io(); if (retval != 0) printf("%s: Failed to setup I/O APICs: returned %d\n", best_enum->apic_name, retval); #ifdef XEN return; #endif /* * Finish setting up the local APIC on the BSP once we know how to * properly program the LINT pins. */ lapic_setup(1); if (bootverbose) lapic_dump("BSP"); /* Enable the MSI "pic". */ msi_init(); } SYSINIT(apic_setup_io, SI_SUB_INTR, SI_ORDER_SECOND, apic_setup_io, NULL); #ifdef SMP /* * Inter Processor Interrupt functions. The lapic_ipi_*() functions are * private to the MD code. The public interface for the rest of the * kernel is defined in mp_machdep.c. */ int lapic_ipi_wait(int delay) { - int x, incr; + int x; /* - * Wait delay loops for IPI to be sent. This is highly bogus - * since this is sensitive to CPU clock speed. If delay is + * Wait delay microseconds for IPI to be sent. If delay is * -1, we wait forever. */ if (delay == -1) { - incr = 0; - delay = 1; - } else - incr = 1; - for (x = 0; x < delay; x += incr) { + while ((lapic->icr_lo & APIC_DELSTAT_MASK) != APIC_DELSTAT_IDLE) + ia32_pause(); + return (1); + } + + for (x = 0; x < delay; x += 5) { if ((lapic->icr_lo & APIC_DELSTAT_MASK) == APIC_DELSTAT_IDLE) return (1); - ia32_pause(); + DELAY(5); } return (0); } void lapic_ipi_raw(register_t icrlo, u_int dest) { register_t value, saveintr; /* XXX: Need more sanity checking of icrlo? */ KASSERT(lapic != NULL, ("%s called too early", __func__)); KASSERT((dest & ~(APIC_ID_MASK >> APIC_ID_SHIFT)) == 0, ("%s: invalid dest field", __func__)); KASSERT((icrlo & APIC_ICRLO_RESV_MASK) == 0, ("%s: reserved bits set in ICR LO register", __func__)); /* Set destination in ICR HI register if it is being used. */ saveintr = intr_disable(); if ((icrlo & APIC_DEST_MASK) == APIC_DEST_DESTFLD) { value = lapic->icr_hi; value &= ~APIC_ID_MASK; value |= dest << APIC_ID_SHIFT; lapic->icr_hi = value; } /* Program the contents of the IPI and dispatch it. */ value = lapic->icr_lo; value &= APIC_ICRLO_RESV_MASK; value |= icrlo; lapic->icr_lo = value; intr_restore(saveintr); } -#define BEFORE_SPIN 1000000 +#define BEFORE_SPIN 50000 #ifdef DETECT_DEADLOCK -#define AFTER_SPIN 1000 +#define AFTER_SPIN 50 #endif void lapic_ipi_vectored(u_int vector, int dest) { register_t icrlo, destfield; KASSERT((vector & ~APIC_VECTOR_MASK) == 0, ("%s: invalid vector %d", __func__, vector)); - icrlo = APIC_DESTMODE_PHY | APIC_TRIGMOD_EDGE; + icrlo = APIC_DESTMODE_PHY | APIC_TRIGMOD_EDGE | APIC_LEVEL_ASSERT; /* * IPI_STOP_HARD is just a "fake" vector used to send a NMI. * Use special rules regard NMI if passed, otherwise specify * the vector. */ if (vector == IPI_STOP_HARD) - icrlo |= APIC_DELMODE_NMI | APIC_LEVEL_ASSERT; + icrlo |= APIC_DELMODE_NMI; else - icrlo |= vector | APIC_DELMODE_FIXED | APIC_LEVEL_DEASSERT; + icrlo |= vector | APIC_DELMODE_FIXED; destfield = 0; switch (dest) { case APIC_IPI_DEST_SELF: icrlo |= APIC_DEST_SELF; break; case APIC_IPI_DEST_ALL: icrlo |= APIC_DEST_ALLISELF; break; case APIC_IPI_DEST_OTHERS: icrlo |= APIC_DEST_ALLESELF; break; default: KASSERT((dest & ~(APIC_ID_MASK >> APIC_ID_SHIFT)) == 0, ("%s: invalid destination 0x%x", __func__, dest)); destfield = dest; } /* Wait for an earlier IPI to finish. */ if (!lapic_ipi_wait(BEFORE_SPIN)) { if (panicstr != NULL) return; else panic("APIC: Previous IPI is stuck"); } lapic_ipi_raw(icrlo, destfield); #ifdef DETECT_DEADLOCK /* Wait for IPI to be delivered. */ if (!lapic_ipi_wait(AFTER_SPIN)) { #ifdef needsattention /* * XXX FIXME: * * The above function waits for the message to actually be * delivered. It breaks out after an arbitrary timeout * since the message should eventually be delivered (at * least in theory) and that if it wasn't we would catch * the failure with the check above when the next IPI is * sent. * * We could skip this wait entirely, EXCEPT it probably * protects us from other routines that assume that the * message was delivered and acted upon when this function * returns. */ printf("APIC: IPI might be stuck\n"); #else /* !needsattention */ /* Wait until mesage is sent without a timeout. */ while (lapic->icr_lo & APIC_DELSTAT_PEND) ia32_pause(); #endif /* needsattention */ } #endif /* DETECT_DEADLOCK */ } #endif /* SMP */ Index: stable/10 =================================================================== --- stable/10 (revision 281559) +++ stable/10 (revision 281560) Property changes on: stable/10 ___________________________________________________________________ Modified: svn:mergeinfo ## -0,0 +0,1 ## Merged /head:r278325,280866