Index: head/sys/mips/conf/TP-WN1043ND.hints
===================================================================
--- head/sys/mips/conf/TP-WN1043ND.hints	(revision 227937)
+++ head/sys/mips/conf/TP-WN1043ND.hints	(revision 227938)
@@ -1,94 +1,77 @@
 #
 # This file adds to the values in AR91XX_BASE.hints.
 #
 # $FreeBSD$
 
 # Hard-code the PHY for now, until there's switch phy support.
 hint.arge.0.phymask=0x000c
 hint.arge.0.media=1000
 hint.arge.0.fduplex=1
 # Where is the MAC address stored in flash for this particular unit.
 hint.arge.0.eeprommac=0x1f01fc00
 
 # This isn't used, but configure it anyway.
 # This should eventually just not be configured, but the if then
 # needs to be properly disabled or spurious interrupts occur.
 hint.arge.1.phymask=0x0
 
 # Where the ART is
 hint.ath.0.eepromaddr=0x1fff1000
 
 #
 # Define a slightly custom flash layout.
 
 # The default flash layout:
 #
 # 128k: uboot
 # 1024k: kernel
 # 4096k: rootfs
 # 2816: unknown
 # 64k: board config?
 # 64k: ART
 #
 # from printenv:
 # bootargs=console=ttyS0,115200 root=31:02 rootfstype=jffs2 init=/sbin/init
 #    mtdparts=ar9100-nor0:128k(u-boot),1024k(kernel),4096k(rootfs),64k(art)
 
 # This isn't a lot of space!
 # So:
 # 128k: uboot
 # 2048k: kernel
-# 5824k: rootfs
+# 5888k: rootfs
 # 64k: config
-# 64k: board config?
 # 64k: ART
 
 hint.map.0.at="flash/spi0"
 hint.map.0.start=0x00000000
 hint.map.0.end=0x000200000
 hint.map.0.name="uboot"
 hint.map.0.readonly=1
 
 hint.map.1.at="flash/spi0"
 hint.map.1.start=0x00020000
 hint.map.1.end=0x00220000
 hint.map.1.name="kernel"
 hint.map.1.readonly=1
 
 hint.map.2.at="flash/spi0"
 hint.map.2.start=0x00220000
-hint.map.2.end=0x007c0000
+hint.map.2.end=0x007e0000
 hint.map.2.name="rootfs"
 hint.map.2.readonly=1
 
 hint.map.3.at="flash/spi0"
-hint.map.3.start=0x007c0000
-hint.map.3.end=0x007d0000
+hint.map.3.start=0x007e0000
+hint.map.3.end=0x007f0000
 hint.map.3.name="cfg"
 hint.map.3.readonly=0
 
-# I'm not sure what this is!
-#
-# It does however start with "55 aa" which is an AR5416 EEPROM
-# magic value, followed by what looks like a set of ethernet
-# MAC addresses, then a bunch of what looks like my local firmware
-# board configuration.
-#
-# For now, I'm going to leave this particular chunk of flash
-# alone.
-#
-hint.map.4.at="flash/spi0"
-hint.map.4.start=0x007d0000
-hint.map.4.end=0x007e0000
-hint.map.4.name="unknown"
-hint.map.4.readonly=1
-
 # This is radio calibration section.  It is (or should be!) unique
 # for each board, to take into account thermal and electrical differences
 # as well as the regulatory compliance data.
 #
-hint.map.5.at="flash/spi0"
-hint.map.5.start=0x007f0000
-hint.map.5.end=0x00800000
-hint.map.5.name="art"
-hint.map.5.readonly=1
+hint.map.4.at="flash/spi0"
+hint.map.4.start=0x007f0000
+hint.map.4.end=0x00800000
+hint.map.4.name="art"
+hint.map.4.readonly=1