diff --git a/sys/dev/re/if_re.c b/sys/dev/re/if_re.c index 61c0c897c3a1..40799c503387 100644 --- a/sys/dev/re/if_re.c +++ b/sys/dev/re/if_re.c @@ -1,2492 +1,2494 @@ /*- * Copyright (c) 1997, 1998-2003 * Bill Paul . All rights reserved. * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * 1. Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in the * documentation and/or other materials provided with the distribution. * 3. All advertising materials mentioning features or use of this software * must display the following acknowledgement: * This product includes software developed by Bill Paul. * 4. Neither the name of the author nor the names of any co-contributors * may be used to endorse or promote products derived from this software * without specific prior written permission. * * THIS SOFTWARE IS PROVIDED BY Bill Paul AND CONTRIBUTORS ``AS IS'' AND * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE * ARE DISCLAIMED. IN NO EVENT SHALL Bill Paul OR THE VOICES IN HIS HEAD * BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF * THE POSSIBILITY OF SUCH DAMAGE. */ #include __FBSDID("$FreeBSD$"); /* * RealTek 8139C+/8169/8169S/8110S PCI NIC driver * * Written by Bill Paul * Senior Networking Software Engineer * Wind River Systems */ /* * This driver is designed to support RealTek's next generation of * 10/100 and 10/100/1000 PCI ethernet controllers. There are currently * four devices in this family: the RTL8139C+, the RTL8169, the RTL8169S * and the RTL8110S. * * The 8139C+ is a 10/100 ethernet chip. It is backwards compatible * with the older 8139 family, however it also supports a special * C+ mode of operation that provides several new performance enhancing * features. These include: * * o Descriptor based DMA mechanism. Each descriptor represents * a single packet fragment. Data buffers may be aligned on * any byte boundary. * * o 64-bit DMA * * o TCP/IP checksum offload for both RX and TX * * o High and normal priority transmit DMA rings * * o VLAN tag insertion and extraction * * o TCP large send (segmentation offload) * * Like the 8139, the 8139C+ also has a built-in 10/100 PHY. The C+ * programming API is fairly straightforward. The RX filtering, EEPROM * access and PHY access is the same as it is on the older 8139 series * chips. * * The 8169 is a 64-bit 10/100/1000 gigabit ethernet MAC. It has almost the * same programming API and feature set as the 8139C+ with the following * differences and additions: * * o 1000Mbps mode * * o Jumbo frames * * o GMII and TBI ports/registers for interfacing with copper * or fiber PHYs * * o RX and TX DMA rings can have up to 1024 descriptors * (the 8139C+ allows a maximum of 64) * * o Slight differences in register layout from the 8139C+ * * The TX start and timer interrupt registers are at different locations * on the 8169 than they are on the 8139C+. Also, the status word in the * RX descriptor has a slightly different bit layout. The 8169 does not * have a built-in PHY. Most reference boards use a Marvell 88E1000 'Alaska' * copper gigE PHY. * * The 8169S/8110S 10/100/1000 devices have built-in copper gigE PHYs * (the 'S' stands for 'single-chip'). These devices have the same * programming API as the older 8169, but also have some vendor-specific * registers for the on-board PHY. The 8110S is a LAN-on-motherboard * part designed to be pin-compatible with the RealTek 8100 10/100 chip. * * This driver takes advantage of the RX and TX checksum offload and * VLAN tag insertion/extraction features. It also implements TX * interrupt moderation using the timer interrupt registers, which * significantly reduces TX interrupt load. There is also support * for jumbo frames, however the 8169/8169S/8110S can not transmit * jumbo frames larger than 7440, so the max MTU possible with this * driver is 7422 bytes. */ #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include MODULE_DEPEND(re, pci, 1, 1, 1); MODULE_DEPEND(re, ether, 1, 1, 1); MODULE_DEPEND(re, miibus, 1, 1, 1); /* "controller miibus0" required. See GENERIC if you get errors here. */ #include "miibus_if.h" /* * Default to using PIO access for this driver. */ #define RE_USEIOSPACE #include #define RE_CSUM_FEATURES (CSUM_IP | CSUM_TCP | CSUM_UDP) /* * Various supported device vendors/types and their names. */ static struct rl_type re_devs[] = { + { DLINK_VENDORID, DLINK_DEVICEID_528T, RL_HWREV_8169S, + "D-Link DGE-528(T) Gigabit Ethernet Adapter" }, { RT_VENDORID, RT_DEVICEID_8139, RL_HWREV_8139CPLUS, "RealTek 8139C+ 10/100BaseTX" }, { RT_VENDORID, RT_DEVICEID_8169, RL_HWREV_8169, "RealTek 8169 Gigabit Ethernet" }, { RT_VENDORID, RT_DEVICEID_8169, RL_HWREV_8169S, "RealTek 8169S Single-chip Gigabit Ethernet" }, { RT_VENDORID, RT_DEVICEID_8169, RL_HWREV_8169SB, "RealTek 8169SB Single-chip Gigabit Ethernet" }, { RT_VENDORID, RT_DEVICEID_8169, RL_HWREV_8110S, "RealTek 8110S Single-chip Gigabit Ethernet" }, { COREGA_VENDORID, COREGA_DEVICEID_CGLAPCIGT, RL_HWREV_8169S, "Corega CG-LAPCIGT (RTL8169S) Gigabit Ethernet" }, { 0, 0, 0, NULL } }; static struct rl_hwrev re_hwrevs[] = { { RL_HWREV_8139, RL_8139, "" }, { RL_HWREV_8139A, RL_8139, "A" }, { RL_HWREV_8139AG, RL_8139, "A-G" }, { RL_HWREV_8139B, RL_8139, "B" }, { RL_HWREV_8130, RL_8139, "8130" }, { RL_HWREV_8139C, RL_8139, "C" }, { RL_HWREV_8139D, RL_8139, "8139D/8100B/8100C" }, { RL_HWREV_8139CPLUS, RL_8139CPLUS, "C+"}, { RL_HWREV_8169, RL_8169, "8169"}, { RL_HWREV_8169S, RL_8169, "8169S"}, { RL_HWREV_8169SB, RL_8169, "8169SB"}, { RL_HWREV_8110S, RL_8169, "8110S"}, { RL_HWREV_8100, RL_8139, "8100"}, { RL_HWREV_8101, RL_8139, "8101"}, { 0, 0, NULL } }; static int re_probe (device_t); static int re_attach (device_t); static int re_detach (device_t); static int re_encap (struct rl_softc *, struct mbuf **, int *); static void re_dma_map_addr (void *, bus_dma_segment_t *, int, int); static void re_dma_map_desc (void *, bus_dma_segment_t *, int, bus_size_t, int); static int re_allocmem (device_t, struct rl_softc *); static int re_newbuf (struct rl_softc *, int, struct mbuf *); static int re_rx_list_init (struct rl_softc *); static int re_tx_list_init (struct rl_softc *); #ifdef RE_FIXUP_RX static __inline void re_fixup_rx (struct mbuf *); #endif static void re_rxeof (struct rl_softc *); static void re_txeof (struct rl_softc *); #ifdef DEVICE_POLLING static void re_poll (struct ifnet *, enum poll_cmd, int); static void re_poll_locked (struct ifnet *, enum poll_cmd, int); #endif static void re_intr (void *); static void re_tick (void *); static void re_tick_locked (struct rl_softc *); static void re_start (struct ifnet *); static void re_start_locked (struct ifnet *); static int re_ioctl (struct ifnet *, u_long, caddr_t); static void re_init (void *); static void re_init_locked (struct rl_softc *); static void re_stop (struct rl_softc *); static void re_watchdog (struct ifnet *); static int re_suspend (device_t); static int re_resume (device_t); static void re_shutdown (device_t); static int re_ifmedia_upd (struct ifnet *); static void re_ifmedia_sts (struct ifnet *, struct ifmediareq *); static void re_eeprom_putbyte (struct rl_softc *, int); static void re_eeprom_getword (struct rl_softc *, int, u_int16_t *); static void re_read_eeprom (struct rl_softc *, caddr_t, int, int, int); static int re_gmii_readreg (device_t, int, int); static int re_gmii_writereg (device_t, int, int, int); static int re_miibus_readreg (device_t, int, int); static int re_miibus_writereg (device_t, int, int, int); static void re_miibus_statchg (device_t); static void re_setmulti (struct rl_softc *); static void re_reset (struct rl_softc *); static int re_diag (struct rl_softc *); #ifdef RE_USEIOSPACE #define RL_RES SYS_RES_IOPORT #define RL_RID RL_PCI_LOIO #else #define RL_RES SYS_RES_MEMORY #define RL_RID RL_PCI_LOMEM #endif static device_method_t re_methods[] = { /* Device interface */ DEVMETHOD(device_probe, re_probe), DEVMETHOD(device_attach, re_attach), DEVMETHOD(device_detach, re_detach), DEVMETHOD(device_suspend, re_suspend), DEVMETHOD(device_resume, re_resume), DEVMETHOD(device_shutdown, re_shutdown), /* bus interface */ DEVMETHOD(bus_print_child, bus_generic_print_child), DEVMETHOD(bus_driver_added, bus_generic_driver_added), /* MII interface */ DEVMETHOD(miibus_readreg, re_miibus_readreg), DEVMETHOD(miibus_writereg, re_miibus_writereg), DEVMETHOD(miibus_statchg, re_miibus_statchg), { 0, 0 } }; static driver_t re_driver = { "re", re_methods, sizeof(struct rl_softc) }; static devclass_t re_devclass; DRIVER_MODULE(re, pci, re_driver, re_devclass, 0, 0); DRIVER_MODULE(re, cardbus, re_driver, re_devclass, 0, 0); DRIVER_MODULE(miibus, re, miibus_driver, miibus_devclass, 0, 0); #define EE_SET(x) \ CSR_WRITE_1(sc, RL_EECMD, \ CSR_READ_1(sc, RL_EECMD) | x) #define EE_CLR(x) \ CSR_WRITE_1(sc, RL_EECMD, \ CSR_READ_1(sc, RL_EECMD) & ~x) /* * Send a read command and address to the EEPROM, check for ACK. */ static void re_eeprom_putbyte(sc, addr) struct rl_softc *sc; int addr; { register int d, i; d = addr | sc->rl_eecmd_read; /* * Feed in each bit and strobe the clock. */ for (i = 0x400; i; i >>= 1) { if (d & i) { EE_SET(RL_EE_DATAIN); } else { EE_CLR(RL_EE_DATAIN); } DELAY(100); EE_SET(RL_EE_CLK); DELAY(150); EE_CLR(RL_EE_CLK); DELAY(100); } } /* * Read a word of data stored in the EEPROM at address 'addr.' */ static void re_eeprom_getword(sc, addr, dest) struct rl_softc *sc; int addr; u_int16_t *dest; { register int i; u_int16_t word = 0; /* Enter EEPROM access mode. */ CSR_WRITE_1(sc, RL_EECMD, RL_EEMODE_PROGRAM|RL_EE_SEL); /* * Send address of word we want to read. */ re_eeprom_putbyte(sc, addr); CSR_WRITE_1(sc, RL_EECMD, RL_EEMODE_PROGRAM|RL_EE_SEL); /* * Start reading bits from EEPROM. */ for (i = 0x8000; i; i >>= 1) { EE_SET(RL_EE_CLK); DELAY(100); if (CSR_READ_1(sc, RL_EECMD) & RL_EE_DATAOUT) word |= i; EE_CLR(RL_EE_CLK); DELAY(100); } /* Turn off EEPROM access mode. */ CSR_WRITE_1(sc, RL_EECMD, RL_EEMODE_OFF); *dest = word; } /* * Read a sequence of words from the EEPROM. */ static void re_read_eeprom(sc, dest, off, cnt, swap) struct rl_softc *sc; caddr_t dest; int off; int cnt; int swap; { int i; u_int16_t word = 0, *ptr; for (i = 0; i < cnt; i++) { re_eeprom_getword(sc, off + i, &word); ptr = (u_int16_t *)(dest + (i * 2)); if (swap) *ptr = ntohs(word); else *ptr = word; } } static int re_gmii_readreg(dev, phy, reg) device_t dev; int phy, reg; { struct rl_softc *sc; u_int32_t rval; int i; if (phy != 1) return (0); sc = device_get_softc(dev); /* Let the rgephy driver read the GMEDIASTAT register */ if (reg == RL_GMEDIASTAT) { rval = CSR_READ_1(sc, RL_GMEDIASTAT); return (rval); } CSR_WRITE_4(sc, RL_PHYAR, reg << 16); DELAY(1000); for (i = 0; i < RL_TIMEOUT; i++) { rval = CSR_READ_4(sc, RL_PHYAR); if (rval & RL_PHYAR_BUSY) break; DELAY(100); } if (i == RL_TIMEOUT) { printf ("re%d: PHY read failed\n", sc->rl_unit); return (0); } return (rval & RL_PHYAR_PHYDATA); } static int re_gmii_writereg(dev, phy, reg, data) device_t dev; int phy, reg, data; { struct rl_softc *sc; u_int32_t rval; int i; sc = device_get_softc(dev); CSR_WRITE_4(sc, RL_PHYAR, (reg << 16) | (data & RL_PHYAR_PHYDATA) | RL_PHYAR_BUSY); DELAY(1000); for (i = 0; i < RL_TIMEOUT; i++) { rval = CSR_READ_4(sc, RL_PHYAR); if (!(rval & RL_PHYAR_BUSY)) break; DELAY(100); } if (i == RL_TIMEOUT) { printf ("re%d: PHY write failed\n", sc->rl_unit); return (0); } return (0); } static int re_miibus_readreg(dev, phy, reg) device_t dev; int phy, reg; { struct rl_softc *sc; u_int16_t rval = 0; u_int16_t re8139_reg = 0; sc = device_get_softc(dev); if (sc->rl_type == RL_8169) { rval = re_gmii_readreg(dev, phy, reg); return (rval); } /* Pretend the internal PHY is only at address 0 */ if (phy) { return (0); } switch (reg) { case MII_BMCR: re8139_reg = RL_BMCR; break; case MII_BMSR: re8139_reg = RL_BMSR; break; case MII_ANAR: re8139_reg = RL_ANAR; break; case MII_ANER: re8139_reg = RL_ANER; break; case MII_ANLPAR: re8139_reg = RL_LPAR; break; case MII_PHYIDR1: case MII_PHYIDR2: return (0); /* * Allow the rlphy driver to read the media status * register. If we have a link partner which does not * support NWAY, this is the register which will tell * us the results of parallel detection. */ case RL_MEDIASTAT: rval = CSR_READ_1(sc, RL_MEDIASTAT); return (rval); default: printf("re%d: bad phy register\n", sc->rl_unit); return (0); } rval = CSR_READ_2(sc, re8139_reg); return (rval); } static int re_miibus_writereg(dev, phy, reg, data) device_t dev; int phy, reg, data; { struct rl_softc *sc; u_int16_t re8139_reg = 0; int rval = 0; sc = device_get_softc(dev); if (sc->rl_type == RL_8169) { rval = re_gmii_writereg(dev, phy, reg, data); return (rval); } /* Pretend the internal PHY is only at address 0 */ if (phy) return (0); switch (reg) { case MII_BMCR: re8139_reg = RL_BMCR; break; case MII_BMSR: re8139_reg = RL_BMSR; break; case MII_ANAR: re8139_reg = RL_ANAR; break; case MII_ANER: re8139_reg = RL_ANER; break; case MII_ANLPAR: re8139_reg = RL_LPAR; break; case MII_PHYIDR1: case MII_PHYIDR2: return (0); break; default: printf("re%d: bad phy register\n", sc->rl_unit); return (0); } CSR_WRITE_2(sc, re8139_reg, data); return (0); } static void re_miibus_statchg(dev) device_t dev; { } /* * Program the 64-bit multicast hash filter. */ static void re_setmulti(sc) struct rl_softc *sc; { struct ifnet *ifp; int h = 0; u_int32_t hashes[2] = { 0, 0 }; struct ifmultiaddr *ifma; u_int32_t rxfilt; int mcnt = 0; RL_LOCK_ASSERT(sc); ifp = sc->rl_ifp; rxfilt = CSR_READ_4(sc, RL_RXCFG); if (ifp->if_flags & IFF_ALLMULTI || ifp->if_flags & IFF_PROMISC) { rxfilt |= RL_RXCFG_RX_MULTI; CSR_WRITE_4(sc, RL_RXCFG, rxfilt); CSR_WRITE_4(sc, RL_MAR0, 0xFFFFFFFF); CSR_WRITE_4(sc, RL_MAR4, 0xFFFFFFFF); return; } /* first, zot all the existing hash bits */ CSR_WRITE_4(sc, RL_MAR0, 0); CSR_WRITE_4(sc, RL_MAR4, 0); /* now program new ones */ IF_ADDR_LOCK(ifp); TAILQ_FOREACH(ifma, &ifp->if_multiaddrs, ifma_link) { if (ifma->ifma_addr->sa_family != AF_LINK) continue; h = ether_crc32_be(LLADDR((struct sockaddr_dl *) ifma->ifma_addr), ETHER_ADDR_LEN) >> 26; if (h < 32) hashes[0] |= (1 << h); else hashes[1] |= (1 << (h - 32)); mcnt++; } IF_ADDR_UNLOCK(ifp); if (mcnt) rxfilt |= RL_RXCFG_RX_MULTI; else rxfilt &= ~RL_RXCFG_RX_MULTI; CSR_WRITE_4(sc, RL_RXCFG, rxfilt); CSR_WRITE_4(sc, RL_MAR0, hashes[0]); CSR_WRITE_4(sc, RL_MAR4, hashes[1]); } static void re_reset(sc) struct rl_softc *sc; { register int i; RL_LOCK_ASSERT(sc); CSR_WRITE_1(sc, RL_COMMAND, RL_CMD_RESET); for (i = 0; i < RL_TIMEOUT; i++) { DELAY(10); if (!(CSR_READ_1(sc, RL_COMMAND) & RL_CMD_RESET)) break; } if (i == RL_TIMEOUT) printf("re%d: reset never completed!\n", sc->rl_unit); CSR_WRITE_1(sc, 0x82, 1); } /* * The following routine is designed to test for a defect on some * 32-bit 8169 cards. Some of these NICs have the REQ64# and ACK64# * lines connected to the bus, however for a 32-bit only card, they * should be pulled high. The result of this defect is that the * NIC will not work right if you plug it into a 64-bit slot: DMA * operations will be done with 64-bit transfers, which will fail * because the 64-bit data lines aren't connected. * * There's no way to work around this (short of talking a soldering * iron to the board), however we can detect it. The method we use * here is to put the NIC into digital loopback mode, set the receiver * to promiscuous mode, and then try to send a frame. We then compare * the frame data we sent to what was received. If the data matches, * then the NIC is working correctly, otherwise we know the user has * a defective NIC which has been mistakenly plugged into a 64-bit PCI * slot. In the latter case, there's no way the NIC can work correctly, * so we print out a message on the console and abort the device attach. */ static int re_diag(sc) struct rl_softc *sc; { struct ifnet *ifp = sc->rl_ifp; struct mbuf *m0; struct ether_header *eh; struct rl_desc *cur_rx; u_int16_t status; u_int32_t rxstat; int total_len, i, error = 0; u_int8_t dst[] = { 0x00, 'h', 'e', 'l', 'l', 'o' }; u_int8_t src[] = { 0x00, 'w', 'o', 'r', 'l', 'd' }; /* Allocate a single mbuf */ MGETHDR(m0, M_DONTWAIT, MT_DATA); if (m0 == NULL) return (ENOBUFS); RL_LOCK(sc); /* * Initialize the NIC in test mode. This sets the chip up * so that it can send and receive frames, but performs the * following special functions: * - Puts receiver in promiscuous mode * - Enables digital loopback mode * - Leaves interrupts turned off */ ifp->if_flags |= IFF_PROMISC; sc->rl_testmode = 1; re_init_locked(sc); re_stop(sc); DELAY(100000); re_init_locked(sc); /* Put some data in the mbuf */ eh = mtod(m0, struct ether_header *); bcopy ((char *)&dst, eh->ether_dhost, ETHER_ADDR_LEN); bcopy ((char *)&src, eh->ether_shost, ETHER_ADDR_LEN); eh->ether_type = htons(ETHERTYPE_IP); m0->m_pkthdr.len = m0->m_len = ETHER_MIN_LEN - ETHER_CRC_LEN; /* * Queue the packet, start transmission. * Note: IF_HANDOFF() ultimately calls re_start() for us. */ CSR_WRITE_2(sc, RL_ISR, 0xFFFF); RL_UNLOCK(sc); /* XXX: re_diag must not be called when in ALTQ mode */ IF_HANDOFF(&ifp->if_snd, m0, ifp); RL_LOCK(sc); m0 = NULL; /* Wait for it to propagate through the chip */ DELAY(100000); for (i = 0; i < RL_TIMEOUT; i++) { status = CSR_READ_2(sc, RL_ISR); if ((status & (RL_ISR_TIMEOUT_EXPIRED|RL_ISR_RX_OK)) == (RL_ISR_TIMEOUT_EXPIRED|RL_ISR_RX_OK)) break; DELAY(10); } if (i == RL_TIMEOUT) { printf("re%d: diagnostic failed, failed to receive packet " "in loopback mode\n", sc->rl_unit); error = EIO; goto done; } /* * The packet should have been dumped into the first * entry in the RX DMA ring. Grab it from there. */ bus_dmamap_sync(sc->rl_ldata.rl_rx_list_tag, sc->rl_ldata.rl_rx_list_map, BUS_DMASYNC_POSTREAD); bus_dmamap_sync(sc->rl_ldata.rl_mtag, sc->rl_ldata.rl_rx_dmamap[0], BUS_DMASYNC_POSTWRITE); bus_dmamap_unload(sc->rl_ldata.rl_mtag, sc->rl_ldata.rl_rx_dmamap[0]); m0 = sc->rl_ldata.rl_rx_mbuf[0]; sc->rl_ldata.rl_rx_mbuf[0] = NULL; eh = mtod(m0, struct ether_header *); cur_rx = &sc->rl_ldata.rl_rx_list[0]; total_len = RL_RXBYTES(cur_rx); rxstat = le32toh(cur_rx->rl_cmdstat); if (total_len != ETHER_MIN_LEN) { printf("re%d: diagnostic failed, received short packet\n", sc->rl_unit); error = EIO; goto done; } /* Test that the received packet data matches what we sent. */ if (bcmp((char *)&eh->ether_dhost, (char *)&dst, ETHER_ADDR_LEN) || bcmp((char *)&eh->ether_shost, (char *)&src, ETHER_ADDR_LEN) || ntohs(eh->ether_type) != ETHERTYPE_IP) { printf("re%d: WARNING, DMA FAILURE!\n", sc->rl_unit); printf("re%d: expected TX data: %6D/%6D/0x%x\n", sc->rl_unit, dst, ":", src, ":", ETHERTYPE_IP); printf("re%d: received RX data: %6D/%6D/0x%x\n", sc->rl_unit, eh->ether_dhost, ":", eh->ether_shost, ":", ntohs(eh->ether_type)); printf("re%d: You may have a defective 32-bit NIC plugged " "into a 64-bit PCI slot.\n", sc->rl_unit); printf("re%d: Please re-install the NIC in a 32-bit slot " "for proper operation.\n", sc->rl_unit); printf("re%d: Read the re(4) man page for more details.\n", sc->rl_unit); error = EIO; } done: /* Turn interface off, release resources */ sc->rl_testmode = 0; ifp->if_flags &= ~IFF_PROMISC; re_stop(sc); if (m0 != NULL) m_freem(m0); RL_UNLOCK(sc); return (error); } /* * Probe for a RealTek 8139C+/8169/8110 chip. Check the PCI vendor and device * IDs against our list and return a device name if we find a match. */ static int re_probe(dev) device_t dev; { struct rl_type *t; struct rl_softc *sc; int rid; u_int32_t hwrev; t = re_devs; sc = device_get_softc(dev); while (t->rl_name != NULL) { if ((pci_get_vendor(dev) == t->rl_vid) && (pci_get_device(dev) == t->rl_did)) { /* * Temporarily map the I/O space * so we can read the chip ID register. */ rid = RL_RID; sc->rl_res = bus_alloc_resource_any(dev, RL_RES, &rid, RF_ACTIVE); if (sc->rl_res == NULL) { device_printf(dev, "couldn't map ports/memory\n"); return (ENXIO); } sc->rl_btag = rman_get_bustag(sc->rl_res); sc->rl_bhandle = rman_get_bushandle(sc->rl_res); hwrev = CSR_READ_4(sc, RL_TXCFG) & RL_TXCFG_HWREV; bus_release_resource(dev, RL_RES, RL_RID, sc->rl_res); if (t->rl_basetype == hwrev) { device_set_desc(dev, t->rl_name); return (BUS_PROBE_DEFAULT); } } t++; } return (ENXIO); } /* * This routine takes the segment list provided as the result of * a bus_dma_map_load() operation and assigns the addresses/lengths * to RealTek DMA descriptors. This can be called either by the RX * code or the TX code. In the RX case, we'll probably wind up mapping * at most one segment. For the TX case, there could be any number of * segments since TX packets may span multiple mbufs. In either case, * if the number of segments is larger than the rl_maxsegs limit * specified by the caller, we abort the mapping operation. Sadly, * whoever designed the buffer mapping API did not provide a way to * return an error from here, so we have to fake it a bit. */ static void re_dma_map_desc(arg, segs, nseg, mapsize, error) void *arg; bus_dma_segment_t *segs; int nseg; bus_size_t mapsize; int error; { struct rl_dmaload_arg *ctx; struct rl_desc *d = NULL; int i = 0, idx; if (error) return; ctx = arg; /* Signal error to caller if there's too many segments */ if (nseg > ctx->rl_maxsegs) { ctx->rl_maxsegs = 0; return; } /* * Map the segment array into descriptors. Note that we set the * start-of-frame and end-of-frame markers for either TX or RX, but * they really only have meaning in the TX case. (In the RX case, * it's the chip that tells us where packets begin and end.) * We also keep track of the end of the ring and set the * end-of-ring bits as needed, and we set the ownership bits * in all except the very first descriptor. (The caller will * set this descriptor later when it start transmission or * reception.) */ idx = ctx->rl_idx; for (;;) { u_int32_t cmdstat; d = &ctx->rl_ring[idx]; if (le32toh(d->rl_cmdstat) & RL_RDESC_STAT_OWN) { ctx->rl_maxsegs = 0; return; } cmdstat = segs[i].ds_len; d->rl_bufaddr_lo = htole32(RL_ADDR_LO(segs[i].ds_addr)); d->rl_bufaddr_hi = htole32(RL_ADDR_HI(segs[i].ds_addr)); if (i == 0) cmdstat |= RL_TDESC_CMD_SOF; else cmdstat |= RL_TDESC_CMD_OWN; if (idx == (RL_RX_DESC_CNT - 1)) cmdstat |= RL_TDESC_CMD_EOR; d->rl_cmdstat = htole32(cmdstat | ctx->rl_flags); i++; if (i == nseg) break; RL_DESC_INC(idx); } d->rl_cmdstat |= htole32(RL_TDESC_CMD_EOF); ctx->rl_maxsegs = nseg; ctx->rl_idx = idx; } /* * Map a single buffer address. */ static void re_dma_map_addr(arg, segs, nseg, error) void *arg; bus_dma_segment_t *segs; int nseg; int error; { bus_addr_t *addr; if (error) return; KASSERT(nseg == 1, ("too many DMA segments, %d should be 1", nseg)); addr = arg; *addr = segs->ds_addr; } static int re_allocmem(dev, sc) device_t dev; struct rl_softc *sc; { int error; int nseg; int i; /* * Allocate map for RX mbufs. */ nseg = 32; error = bus_dma_tag_create(sc->rl_parent_tag, ETHER_ALIGN, 0, BUS_SPACE_MAXADDR_32BIT, BUS_SPACE_MAXADDR, NULL, NULL, MCLBYTES * nseg, nseg, MCLBYTES, BUS_DMA_ALLOCNOW, NULL, NULL, &sc->rl_ldata.rl_mtag); if (error) { device_printf(dev, "could not allocate dma tag\n"); return (ENOMEM); } /* * Allocate map for TX descriptor list. */ error = bus_dma_tag_create(sc->rl_parent_tag, RL_RING_ALIGN, 0, BUS_SPACE_MAXADDR_32BIT, BUS_SPACE_MAXADDR, NULL, NULL, RL_TX_LIST_SZ, 1, RL_TX_LIST_SZ, BUS_DMA_ALLOCNOW, NULL, NULL, &sc->rl_ldata.rl_tx_list_tag); if (error) { device_printf(dev, "could not allocate dma tag\n"); return (ENOMEM); } /* Allocate DMA'able memory for the TX ring */ error = bus_dmamem_alloc(sc->rl_ldata.rl_tx_list_tag, (void **)&sc->rl_ldata.rl_tx_list, BUS_DMA_NOWAIT | BUS_DMA_ZERO, &sc->rl_ldata.rl_tx_list_map); if (error) return (ENOMEM); /* Load the map for the TX ring. */ error = bus_dmamap_load(sc->rl_ldata.rl_tx_list_tag, sc->rl_ldata.rl_tx_list_map, sc->rl_ldata.rl_tx_list, RL_TX_LIST_SZ, re_dma_map_addr, &sc->rl_ldata.rl_tx_list_addr, BUS_DMA_NOWAIT); /* Create DMA maps for TX buffers */ for (i = 0; i < RL_TX_DESC_CNT; i++) { error = bus_dmamap_create(sc->rl_ldata.rl_mtag, 0, &sc->rl_ldata.rl_tx_dmamap[i]); if (error) { device_printf(dev, "can't create DMA map for TX\n"); return (ENOMEM); } } /* * Allocate map for RX descriptor list. */ error = bus_dma_tag_create(sc->rl_parent_tag, RL_RING_ALIGN, 0, BUS_SPACE_MAXADDR_32BIT, BUS_SPACE_MAXADDR, NULL, NULL, RL_RX_LIST_SZ, 1, RL_RX_LIST_SZ, BUS_DMA_ALLOCNOW, NULL, NULL, &sc->rl_ldata.rl_rx_list_tag); if (error) { device_printf(dev, "could not allocate dma tag\n"); return (ENOMEM); } /* Allocate DMA'able memory for the RX ring */ error = bus_dmamem_alloc(sc->rl_ldata.rl_rx_list_tag, (void **)&sc->rl_ldata.rl_rx_list, BUS_DMA_NOWAIT | BUS_DMA_ZERO, &sc->rl_ldata.rl_rx_list_map); if (error) return (ENOMEM); /* Load the map for the RX ring. */ error = bus_dmamap_load(sc->rl_ldata.rl_rx_list_tag, sc->rl_ldata.rl_rx_list_map, sc->rl_ldata.rl_rx_list, RL_RX_LIST_SZ, re_dma_map_addr, &sc->rl_ldata.rl_rx_list_addr, BUS_DMA_NOWAIT); /* Create DMA maps for RX buffers */ for (i = 0; i < RL_RX_DESC_CNT; i++) { error = bus_dmamap_create(sc->rl_ldata.rl_mtag, 0, &sc->rl_ldata.rl_rx_dmamap[i]); if (error) { device_printf(dev, "can't create DMA map for RX\n"); return (ENOMEM); } } return (0); } /* * Attach the interface. Allocate softc structures, do ifmedia * setup and ethernet/BPF attach. */ static int re_attach(dev) device_t dev; { u_char eaddr[ETHER_ADDR_LEN]; u_int16_t as[3]; struct rl_softc *sc; struct ifnet *ifp; struct rl_hwrev *hw_rev; int hwrev; u_int16_t re_did = 0; int unit, error = 0, rid, i; sc = device_get_softc(dev); unit = device_get_unit(dev); mtx_init(&sc->rl_mtx, device_get_nameunit(dev), MTX_NETWORK_LOCK, MTX_DEF); /* * Map control/status registers. */ pci_enable_busmaster(dev); rid = RL_RID; sc->rl_res = bus_alloc_resource_any(dev, RL_RES, &rid, RF_ACTIVE); if (sc->rl_res == NULL) { printf ("re%d: couldn't map ports/memory\n", unit); error = ENXIO; goto fail; } sc->rl_btag = rman_get_bustag(sc->rl_res); sc->rl_bhandle = rman_get_bushandle(sc->rl_res); /* Allocate interrupt */ rid = 0; sc->rl_irq = bus_alloc_resource_any(dev, SYS_RES_IRQ, &rid, RF_SHAREABLE | RF_ACTIVE); if (sc->rl_irq == NULL) { printf("re%d: couldn't map interrupt\n", unit); error = ENXIO; goto fail; } /* Reset the adapter. */ RL_LOCK(sc); re_reset(sc); RL_UNLOCK(sc); hw_rev = re_hwrevs; hwrev = CSR_READ_4(sc, RL_TXCFG) & RL_TXCFG_HWREV; while (hw_rev->rl_desc != NULL) { if (hw_rev->rl_rev == hwrev) { sc->rl_type = hw_rev->rl_type; break; } hw_rev++; } if (sc->rl_type == RL_8169) { /* Set RX length mask */ sc->rl_rxlenmask = RL_RDESC_STAT_GFRAGLEN; /* Force station address autoload from the EEPROM */ CSR_WRITE_1(sc, RL_EECMD, RL_EEMODE_AUTOLOAD); for (i = 0; i < RL_TIMEOUT; i++) { if (!(CSR_READ_1(sc, RL_EECMD) & RL_EEMODE_AUTOLOAD)) break; DELAY(100); } if (i == RL_TIMEOUT) printf ("re%d: eeprom autoload timed out\n", unit); for (i = 0; i < ETHER_ADDR_LEN; i++) eaddr[i] = CSR_READ_1(sc, RL_IDR0 + i); } else { /* Set RX length mask */ sc->rl_rxlenmask = RL_RDESC_STAT_FRAGLEN; sc->rl_eecmd_read = RL_EECMD_READ_6BIT; re_read_eeprom(sc, (caddr_t)&re_did, 0, 1, 0); if (re_did != 0x8129) sc->rl_eecmd_read = RL_EECMD_READ_8BIT; /* * Get station address from the EEPROM. */ re_read_eeprom(sc, (caddr_t)as, RL_EE_EADDR, 3, 0); for (i = 0; i < 3; i++) { eaddr[(i * 2) + 0] = as[i] & 0xff; eaddr[(i * 2) + 1] = as[i] >> 8; } } sc->rl_unit = unit; /* * Allocate the parent bus DMA tag appropriate for PCI. */ #define RL_NSEG_NEW 32 error = bus_dma_tag_create(NULL, /* parent */ 1, 0, /* alignment, boundary */ BUS_SPACE_MAXADDR_32BIT,/* lowaddr */ BUS_SPACE_MAXADDR, /* highaddr */ NULL, NULL, /* filter, filterarg */ MAXBSIZE, RL_NSEG_NEW, /* maxsize, nsegments */ BUS_SPACE_MAXSIZE_32BIT,/* maxsegsize */ BUS_DMA_ALLOCNOW, /* flags */ NULL, NULL, /* lockfunc, lockarg */ &sc->rl_parent_tag); if (error) goto fail; error = re_allocmem(dev, sc); if (error) goto fail; ifp = sc->rl_ifp = if_alloc(IFT_ETHER); if (ifp == NULL) { printf("re%d: can not if_alloc()\n", sc->rl_unit); error = ENOSPC; goto fail; } /* Do MII setup */ if (mii_phy_probe(dev, &sc->rl_miibus, re_ifmedia_upd, re_ifmedia_sts)) { printf("re%d: MII without any phy!\n", sc->rl_unit); error = ENXIO; goto fail; } ifp->if_softc = sc; if_initname(ifp, device_get_name(dev), device_get_unit(dev)); ifp->if_mtu = ETHERMTU; ifp->if_flags = IFF_BROADCAST | IFF_SIMPLEX | IFF_MULTICAST; ifp->if_ioctl = re_ioctl; ifp->if_capabilities = IFCAP_VLAN_MTU; ifp->if_start = re_start; ifp->if_hwassist = /*RE_CSUM_FEATURES*/0; ifp->if_capabilities |= IFCAP_HWCSUM|IFCAP_VLAN_HWTAGGING; #ifdef DEVICE_POLLING ifp->if_capabilities |= IFCAP_POLLING; #endif ifp->if_watchdog = re_watchdog; ifp->if_init = re_init; if (sc->rl_type == RL_8169) ifp->if_baudrate = 1000000000; else ifp->if_baudrate = 100000000; IFQ_SET_MAXLEN(&ifp->if_snd, RL_IFQ_MAXLEN); ifp->if_snd.ifq_drv_maxlen = RL_IFQ_MAXLEN; IFQ_SET_READY(&ifp->if_snd); ifp->if_capenable = ifp->if_capabilities & ~IFCAP_HWCSUM; callout_handle_init(&sc->rl_stat_ch); /* * Call MI attach routine. */ ether_ifattach(ifp, eaddr); /* Perform hardware diagnostic. */ error = re_diag(sc); if (error) { printf("re%d: attach aborted due to hardware diag failure\n", unit); ether_ifdetach(ifp); if_free(ifp); goto fail; } /* Hook interrupt last to avoid having to lock softc */ error = bus_setup_intr(dev, sc->rl_irq, INTR_TYPE_NET | INTR_MPSAFE, re_intr, sc, &sc->rl_intrhand); if (error) { printf("re%d: couldn't set up irq\n", unit); ether_ifdetach(ifp); if_free(ifp); } fail: if (error) re_detach(dev); return (error); } /* * Shutdown hardware and free up resources. This can be called any * time after the mutex has been initialized. It is called in both * the error case in attach and the normal detach case so it needs * to be careful about only freeing resources that have actually been * allocated. */ static int re_detach(dev) device_t dev; { struct rl_softc *sc; struct ifnet *ifp; int i; int attached; sc = device_get_softc(dev); ifp = sc->rl_ifp; KASSERT(mtx_initialized(&sc->rl_mtx), ("re mutex not initialized")); attached = device_is_attached(dev); /* These should only be active if attach succeeded */ if (attached) ether_ifdetach(ifp); if (ifp == NULL) if_free(ifp); RL_LOCK(sc); #if 0 sc->suspended = 1; #endif /* These should only be active if attach succeeded */ if (attached) { re_stop(sc); /* * Force off the IFF_UP flag here, in case someone * still had a BPF descriptor attached to this * interface. If they do, ether_ifdetach() will cause * the BPF code to try and clear the promisc mode * flag, which will bubble down to re_ioctl(), * which will try to call re_init() again. This will * turn the NIC back on and restart the MII ticker, * which will panic the system when the kernel tries * to invoke the re_tick() function that isn't there * anymore. */ ifp->if_flags &= ~IFF_UP; } if (sc->rl_miibus) device_delete_child(dev, sc->rl_miibus); bus_generic_detach(dev); /* * The rest is resource deallocation, so we should already be * stopped here. */ RL_UNLOCK(sc); if (sc->rl_intrhand) bus_teardown_intr(dev, sc->rl_irq, sc->rl_intrhand); if (sc->rl_irq) bus_release_resource(dev, SYS_RES_IRQ, 0, sc->rl_irq); if (sc->rl_res) bus_release_resource(dev, RL_RES, RL_RID, sc->rl_res); /* Unload and free the RX DMA ring memory and map */ if (sc->rl_ldata.rl_rx_list_tag) { bus_dmamap_unload(sc->rl_ldata.rl_rx_list_tag, sc->rl_ldata.rl_rx_list_map); bus_dmamem_free(sc->rl_ldata.rl_rx_list_tag, sc->rl_ldata.rl_rx_list, sc->rl_ldata.rl_rx_list_map); bus_dma_tag_destroy(sc->rl_ldata.rl_rx_list_tag); } /* Unload and free the TX DMA ring memory and map */ if (sc->rl_ldata.rl_tx_list_tag) { bus_dmamap_unload(sc->rl_ldata.rl_tx_list_tag, sc->rl_ldata.rl_tx_list_map); bus_dmamem_free(sc->rl_ldata.rl_tx_list_tag, sc->rl_ldata.rl_tx_list, sc->rl_ldata.rl_tx_list_map); bus_dma_tag_destroy(sc->rl_ldata.rl_tx_list_tag); } /* Destroy all the RX and TX buffer maps */ if (sc->rl_ldata.rl_mtag) { for (i = 0; i < RL_TX_DESC_CNT; i++) bus_dmamap_destroy(sc->rl_ldata.rl_mtag, sc->rl_ldata.rl_tx_dmamap[i]); for (i = 0; i < RL_RX_DESC_CNT; i++) bus_dmamap_destroy(sc->rl_ldata.rl_mtag, sc->rl_ldata.rl_rx_dmamap[i]); bus_dma_tag_destroy(sc->rl_ldata.rl_mtag); } /* Unload and free the stats buffer and map */ if (sc->rl_ldata.rl_stag) { bus_dmamap_unload(sc->rl_ldata.rl_stag, sc->rl_ldata.rl_rx_list_map); bus_dmamem_free(sc->rl_ldata.rl_stag, sc->rl_ldata.rl_stats, sc->rl_ldata.rl_smap); bus_dma_tag_destroy(sc->rl_ldata.rl_stag); } if (sc->rl_parent_tag) bus_dma_tag_destroy(sc->rl_parent_tag); mtx_destroy(&sc->rl_mtx); return (0); } static int re_newbuf(sc, idx, m) struct rl_softc *sc; int idx; struct mbuf *m; { struct rl_dmaload_arg arg; struct mbuf *n = NULL; int error; if (m == NULL) { n = m_getcl(M_DONTWAIT, MT_DATA, M_PKTHDR); if (n == NULL) return (ENOBUFS); m = n; } else m->m_data = m->m_ext.ext_buf; m->m_len = m->m_pkthdr.len = MCLBYTES; #ifdef RE_FIXUP_RX /* * This is part of an evil trick to deal with non-x86 platforms. * The RealTek chip requires RX buffers to be aligned on 64-bit * boundaries, but that will hose non-x86 machines. To get around * this, we leave some empty space at the start of each buffer * and for non-x86 hosts, we copy the buffer back six bytes * to achieve word alignment. This is slightly more efficient * than allocating a new buffer, copying the contents, and * discarding the old buffer. */ m_adj(m, RE_ETHER_ALIGN); #endif arg.sc = sc; arg.rl_idx = idx; arg.rl_maxsegs = 1; arg.rl_flags = 0; arg.rl_ring = sc->rl_ldata.rl_rx_list; error = bus_dmamap_load_mbuf(sc->rl_ldata.rl_mtag, sc->rl_ldata.rl_rx_dmamap[idx], m, re_dma_map_desc, &arg, BUS_DMA_NOWAIT); if (error || arg.rl_maxsegs != 1) { if (n != NULL) m_freem(n); return (ENOMEM); } sc->rl_ldata.rl_rx_list[idx].rl_cmdstat |= htole32(RL_RDESC_CMD_OWN); sc->rl_ldata.rl_rx_mbuf[idx] = m; bus_dmamap_sync(sc->rl_ldata.rl_mtag, sc->rl_ldata.rl_rx_dmamap[idx], BUS_DMASYNC_PREREAD); return (0); } #ifdef RE_FIXUP_RX static __inline void re_fixup_rx(m) struct mbuf *m; { int i; uint16_t *src, *dst; src = mtod(m, uint16_t *); dst = src - (RE_ETHER_ALIGN - ETHER_ALIGN) / sizeof *src; for (i = 0; i < (m->m_len / sizeof(uint16_t) + 1); i++) *dst++ = *src++; m->m_data -= RE_ETHER_ALIGN - ETHER_ALIGN; return; } #endif static int re_tx_list_init(sc) struct rl_softc *sc; { RL_LOCK_ASSERT(sc); bzero ((char *)sc->rl_ldata.rl_tx_list, RL_TX_LIST_SZ); bzero ((char *)&sc->rl_ldata.rl_tx_mbuf, (RL_TX_DESC_CNT * sizeof(struct mbuf *))); bus_dmamap_sync(sc->rl_ldata.rl_tx_list_tag, sc->rl_ldata.rl_tx_list_map, BUS_DMASYNC_PREWRITE); sc->rl_ldata.rl_tx_prodidx = 0; sc->rl_ldata.rl_tx_considx = 0; sc->rl_ldata.rl_tx_free = RL_TX_DESC_CNT; return (0); } static int re_rx_list_init(sc) struct rl_softc *sc; { int i; bzero ((char *)sc->rl_ldata.rl_rx_list, RL_RX_LIST_SZ); bzero ((char *)&sc->rl_ldata.rl_rx_mbuf, (RL_RX_DESC_CNT * sizeof(struct mbuf *))); for (i = 0; i < RL_RX_DESC_CNT; i++) { if (re_newbuf(sc, i, NULL) == ENOBUFS) return (ENOBUFS); } /* Flush the RX descriptors */ bus_dmamap_sync(sc->rl_ldata.rl_rx_list_tag, sc->rl_ldata.rl_rx_list_map, BUS_DMASYNC_PREWRITE|BUS_DMASYNC_PREREAD); sc->rl_ldata.rl_rx_prodidx = 0; sc->rl_head = sc->rl_tail = NULL; return (0); } /* * RX handler for C+ and 8169. For the gigE chips, we support * the reception of jumbo frames that have been fragmented * across multiple 2K mbuf cluster buffers. */ static void re_rxeof(sc) struct rl_softc *sc; { struct mbuf *m; struct ifnet *ifp; int i, total_len; struct rl_desc *cur_rx; u_int32_t rxstat, rxvlan; RL_LOCK_ASSERT(sc); ifp = sc->rl_ifp; i = sc->rl_ldata.rl_rx_prodidx; /* Invalidate the descriptor memory */ bus_dmamap_sync(sc->rl_ldata.rl_rx_list_tag, sc->rl_ldata.rl_rx_list_map, BUS_DMASYNC_POSTREAD); while (!RL_OWN(&sc->rl_ldata.rl_rx_list[i])) { cur_rx = &sc->rl_ldata.rl_rx_list[i]; m = sc->rl_ldata.rl_rx_mbuf[i]; total_len = RL_RXBYTES(cur_rx); rxstat = le32toh(cur_rx->rl_cmdstat); rxvlan = le32toh(cur_rx->rl_vlanctl); /* Invalidate the RX mbuf and unload its map */ bus_dmamap_sync(sc->rl_ldata.rl_mtag, sc->rl_ldata.rl_rx_dmamap[i], BUS_DMASYNC_POSTWRITE); bus_dmamap_unload(sc->rl_ldata.rl_mtag, sc->rl_ldata.rl_rx_dmamap[i]); if (!(rxstat & RL_RDESC_STAT_EOF)) { m->m_len = RE_RX_DESC_BUFLEN; if (sc->rl_head == NULL) sc->rl_head = sc->rl_tail = m; else { m->m_flags &= ~M_PKTHDR; sc->rl_tail->m_next = m; sc->rl_tail = m; } re_newbuf(sc, i, NULL); RL_DESC_INC(i); continue; } /* * NOTE: for the 8139C+, the frame length field * is always 12 bits in size, but for the gigE chips, * it is 13 bits (since the max RX frame length is 16K). * Unfortunately, all 32 bits in the status word * were already used, so to make room for the extra * length bit, RealTek took out the 'frame alignment * error' bit and shifted the other status bits * over one slot. The OWN, EOR, FS and LS bits are * still in the same places. We have already extracted * the frame length and checked the OWN bit, so rather * than using an alternate bit mapping, we shift the * status bits one space to the right so we can evaluate * them using the 8169 status as though it was in the * same format as that of the 8139C+. */ if (sc->rl_type == RL_8169) rxstat >>= 1; /* * if total_len > 2^13-1, both _RXERRSUM and _GIANT will be * set, but if CRC is clear, it will still be a valid frame. */ if (rxstat & RL_RDESC_STAT_RXERRSUM && !(total_len > 8191 && (rxstat & RL_RDESC_STAT_ERRS) == RL_RDESC_STAT_GIANT)) { ifp->if_ierrors++; /* * If this is part of a multi-fragment packet, * discard all the pieces. */ if (sc->rl_head != NULL) { m_freem(sc->rl_head); sc->rl_head = sc->rl_tail = NULL; } re_newbuf(sc, i, m); RL_DESC_INC(i); continue; } /* * If allocating a replacement mbuf fails, * reload the current one. */ if (re_newbuf(sc, i, NULL)) { ifp->if_ierrors++; if (sc->rl_head != NULL) { m_freem(sc->rl_head); sc->rl_head = sc->rl_tail = NULL; } re_newbuf(sc, i, m); RL_DESC_INC(i); continue; } RL_DESC_INC(i); if (sc->rl_head != NULL) { m->m_len = total_len % RE_RX_DESC_BUFLEN; if (m->m_len == 0) m->m_len = RE_RX_DESC_BUFLEN; /* * Special case: if there's 4 bytes or less * in this buffer, the mbuf can be discarded: * the last 4 bytes is the CRC, which we don't * care about anyway. */ if (m->m_len <= ETHER_CRC_LEN) { sc->rl_tail->m_len -= (ETHER_CRC_LEN - m->m_len); m_freem(m); } else { m->m_len -= ETHER_CRC_LEN; m->m_flags &= ~M_PKTHDR; sc->rl_tail->m_next = m; } m = sc->rl_head; sc->rl_head = sc->rl_tail = NULL; m->m_pkthdr.len = total_len - ETHER_CRC_LEN; } else m->m_pkthdr.len = m->m_len = (total_len - ETHER_CRC_LEN); #ifdef RE_FIXUP_RX re_fixup_rx(m); #endif ifp->if_ipackets++; m->m_pkthdr.rcvif = ifp; /* Do RX checksumming if enabled */ if (ifp->if_capenable & IFCAP_RXCSUM) { /* Check IP header checksum */ if (rxstat & RL_RDESC_STAT_PROTOID) m->m_pkthdr.csum_flags |= CSUM_IP_CHECKED; if (!(rxstat & RL_RDESC_STAT_IPSUMBAD)) m->m_pkthdr.csum_flags |= CSUM_IP_VALID; /* Check TCP/UDP checksum */ if ((RL_TCPPKT(rxstat) && !(rxstat & RL_RDESC_STAT_TCPSUMBAD)) || (RL_UDPPKT(rxstat) && !(rxstat & RL_RDESC_STAT_UDPSUMBAD))) { m->m_pkthdr.csum_flags |= CSUM_DATA_VALID|CSUM_PSEUDO_HDR; m->m_pkthdr.csum_data = 0xffff; } } if (rxvlan & RL_RDESC_VLANCTL_TAG) VLAN_INPUT_TAG(ifp, m, ntohs((rxvlan & RL_RDESC_VLANCTL_DATA)), continue); RL_UNLOCK(sc); (*ifp->if_input)(ifp, m); RL_LOCK(sc); } /* Flush the RX DMA ring */ bus_dmamap_sync(sc->rl_ldata.rl_rx_list_tag, sc->rl_ldata.rl_rx_list_map, BUS_DMASYNC_PREWRITE|BUS_DMASYNC_PREREAD); sc->rl_ldata.rl_rx_prodidx = i; } static void re_txeof(sc) struct rl_softc *sc; { struct ifnet *ifp; u_int32_t txstat; int idx; ifp = sc->rl_ifp; idx = sc->rl_ldata.rl_tx_considx; /* Invalidate the TX descriptor list */ bus_dmamap_sync(sc->rl_ldata.rl_tx_list_tag, sc->rl_ldata.rl_tx_list_map, BUS_DMASYNC_POSTREAD); while (idx != sc->rl_ldata.rl_tx_prodidx) { txstat = le32toh(sc->rl_ldata.rl_tx_list[idx].rl_cmdstat); if (txstat & RL_TDESC_CMD_OWN) break; /* * We only stash mbufs in the last descriptor * in a fragment chain, which also happens to * be the only place where the TX status bits * are valid. */ if (txstat & RL_TDESC_CMD_EOF) { m_freem(sc->rl_ldata.rl_tx_mbuf[idx]); sc->rl_ldata.rl_tx_mbuf[idx] = NULL; bus_dmamap_unload(sc->rl_ldata.rl_mtag, sc->rl_ldata.rl_tx_dmamap[idx]); if (txstat & (RL_TDESC_STAT_EXCESSCOL| RL_TDESC_STAT_COLCNT)) ifp->if_collisions++; if (txstat & RL_TDESC_STAT_TXERRSUM) ifp->if_oerrors++; else ifp->if_opackets++; } sc->rl_ldata.rl_tx_free++; RL_DESC_INC(idx); } /* No changes made to the TX ring, so no flush needed */ if (idx != sc->rl_ldata.rl_tx_considx) { sc->rl_ldata.rl_tx_considx = idx; ifp->if_flags &= ~IFF_OACTIVE; ifp->if_timer = 0; } /* * If not all descriptors have been released reaped yet, * reload the timer so that we will eventually get another * interrupt that will cause us to re-enter this routine. * This is done in case the transmitter has gone idle. */ if (sc->rl_ldata.rl_tx_free != RL_TX_DESC_CNT) CSR_WRITE_4(sc, RL_TIMERCNT, 1); } static void re_tick(xsc) void *xsc; { struct rl_softc *sc; sc = xsc; RL_LOCK(sc); re_tick_locked(sc); RL_UNLOCK(sc); } static void re_tick_locked(sc) struct rl_softc *sc; { struct mii_data *mii; RL_LOCK_ASSERT(sc); mii = device_get_softc(sc->rl_miibus); mii_tick(mii); sc->rl_stat_ch = timeout(re_tick, sc, hz); } #ifdef DEVICE_POLLING static void re_poll(struct ifnet *ifp, enum poll_cmd cmd, int count) { struct rl_softc *sc = ifp->if_softc; RL_LOCK(sc); re_poll_locked(ifp, cmd, count); RL_UNLOCK(sc); } static void re_poll_locked(struct ifnet *ifp, enum poll_cmd cmd, int count) { struct rl_softc *sc = ifp->if_softc; RL_LOCK_ASSERT(sc); if (!(ifp->if_capenable & IFCAP_POLLING)) { ether_poll_deregister(ifp); cmd = POLL_DEREGISTER; } if (cmd == POLL_DEREGISTER) { /* final call, enable interrupts */ CSR_WRITE_2(sc, RL_IMR, RL_INTRS_CPLUS); return; } sc->rxcycles = count; re_rxeof(sc); re_txeof(sc); if (!IFQ_DRV_IS_EMPTY(&ifp->if_snd)) re_start_locked(ifp); if (cmd == POLL_AND_CHECK_STATUS) { /* also check status register */ u_int16_t status; status = CSR_READ_2(sc, RL_ISR); if (status == 0xffff) return; if (status) CSR_WRITE_2(sc, RL_ISR, status); /* * XXX check behaviour on receiver stalls. */ if (status & RL_ISR_SYSTEM_ERR) { re_reset(sc); re_init_locked(sc); } } } #endif /* DEVICE_POLLING */ static void re_intr(arg) void *arg; { struct rl_softc *sc; struct ifnet *ifp; u_int16_t status; sc = arg; RL_LOCK(sc); ifp = sc->rl_ifp; if (sc->suspended || !(ifp->if_flags & IFF_UP)) goto done_locked; #ifdef DEVICE_POLLING if (ifp->if_flags & IFF_POLLING) goto done_locked; if ((ifp->if_capenable & IFCAP_POLLING) && ether_poll_register(re_poll, ifp)) { /* ok, disable interrupts */ CSR_WRITE_2(sc, RL_IMR, 0x0000); re_poll_locked(ifp, 0, 1); goto done_locked; } #endif /* DEVICE_POLLING */ for (;;) { status = CSR_READ_2(sc, RL_ISR); /* If the card has gone away the read returns 0xffff. */ if (status == 0xffff) break; if (status) CSR_WRITE_2(sc, RL_ISR, status); if ((status & RL_INTRS_CPLUS) == 0) break; if ((status & RL_ISR_RX_OK) || (status & RL_ISR_RX_ERR)) re_rxeof(sc); if ((status & RL_ISR_TIMEOUT_EXPIRED) || (status & RL_ISR_TX_ERR) || (status & RL_ISR_TX_DESC_UNAVAIL)) re_txeof(sc); if (status & RL_ISR_SYSTEM_ERR) { re_reset(sc); re_init_locked(sc); } if (status & RL_ISR_LINKCHG) { untimeout(re_tick, sc, sc->rl_stat_ch); re_tick_locked(sc); } } if (!IFQ_DRV_IS_EMPTY(&ifp->if_snd)) re_start_locked(ifp); done_locked: RL_UNLOCK(sc); } static int re_encap(sc, m_head, idx) struct rl_softc *sc; struct mbuf **m_head; int *idx; { struct mbuf *m_new = NULL; struct rl_dmaload_arg arg; bus_dmamap_t map; int error; struct m_tag *mtag; RL_LOCK_ASSERT(sc); if (sc->rl_ldata.rl_tx_free <= 4) return (EFBIG); /* * Set up checksum offload. Note: checksum offload bits must * appear in all descriptors of a multi-descriptor transmit * attempt. This is according to testing done with an 8169 * chip. This is a requirement. */ arg.rl_flags = 0; if ((*m_head)->m_pkthdr.csum_flags & CSUM_IP) arg.rl_flags |= RL_TDESC_CMD_IPCSUM; if ((*m_head)->m_pkthdr.csum_flags & CSUM_TCP) arg.rl_flags |= RL_TDESC_CMD_TCPCSUM; if ((*m_head)->m_pkthdr.csum_flags & CSUM_UDP) arg.rl_flags |= RL_TDESC_CMD_UDPCSUM; arg.sc = sc; arg.rl_idx = *idx; arg.rl_maxsegs = sc->rl_ldata.rl_tx_free; if (arg.rl_maxsegs > 4) arg.rl_maxsegs -= 4; arg.rl_ring = sc->rl_ldata.rl_tx_list; map = sc->rl_ldata.rl_tx_dmamap[*idx]; error = bus_dmamap_load_mbuf(sc->rl_ldata.rl_mtag, map, *m_head, re_dma_map_desc, &arg, BUS_DMA_NOWAIT); if (error && error != EFBIG) { printf("re%d: can't map mbuf (error %d)\n", sc->rl_unit, error); return (ENOBUFS); } /* Too many segments to map, coalesce into a single mbuf */ if (error || arg.rl_maxsegs == 0) { m_new = m_defrag(*m_head, M_DONTWAIT); if (m_new == NULL) return (ENOBUFS); else *m_head = m_new; arg.sc = sc; arg.rl_idx = *idx; arg.rl_maxsegs = sc->rl_ldata.rl_tx_free; arg.rl_ring = sc->rl_ldata.rl_tx_list; error = bus_dmamap_load_mbuf(sc->rl_ldata.rl_mtag, map, *m_head, re_dma_map_desc, &arg, BUS_DMA_NOWAIT); if (error) { printf("re%d: can't map mbuf (error %d)\n", sc->rl_unit, error); return (EFBIG); } } /* * Insure that the map for this transmission * is placed at the array index of the last descriptor * in this chain. (Swap last and first dmamaps.) */ sc->rl_ldata.rl_tx_dmamap[*idx] = sc->rl_ldata.rl_tx_dmamap[arg.rl_idx]; sc->rl_ldata.rl_tx_dmamap[arg.rl_idx] = map; sc->rl_ldata.rl_tx_mbuf[arg.rl_idx] = *m_head; sc->rl_ldata.rl_tx_free -= arg.rl_maxsegs; /* * Set up hardware VLAN tagging. Note: vlan tag info must * appear in the first descriptor of a multi-descriptor * transmission attempt. */ mtag = VLAN_OUTPUT_TAG(sc->rl_ifp, *m_head); if (mtag != NULL) sc->rl_ldata.rl_tx_list[*idx].rl_vlanctl = htole32(htons(VLAN_TAG_VALUE(mtag)) | RL_TDESC_VLANCTL_TAG); /* Transfer ownership of packet to the chip. */ sc->rl_ldata.rl_tx_list[arg.rl_idx].rl_cmdstat |= htole32(RL_TDESC_CMD_OWN); if (*idx != arg.rl_idx) sc->rl_ldata.rl_tx_list[*idx].rl_cmdstat |= htole32(RL_TDESC_CMD_OWN); RL_DESC_INC(arg.rl_idx); *idx = arg.rl_idx; return (0); } static void re_start(ifp) struct ifnet *ifp; { struct rl_softc *sc; sc = ifp->if_softc; RL_LOCK(sc); re_start_locked(ifp); RL_UNLOCK(sc); } /* * Main transmit routine for C+ and gigE NICs. */ static void re_start_locked(ifp) struct ifnet *ifp; { struct rl_softc *sc; struct mbuf *m_head = NULL; int idx, queued = 0; sc = ifp->if_softc; RL_LOCK_ASSERT(sc); idx = sc->rl_ldata.rl_tx_prodidx; while (sc->rl_ldata.rl_tx_mbuf[idx] == NULL) { IFQ_DRV_DEQUEUE(&ifp->if_snd, m_head); if (m_head == NULL) break; if (re_encap(sc, &m_head, &idx)) { IFQ_DRV_PREPEND(&ifp->if_snd, m_head); ifp->if_flags |= IFF_OACTIVE; break; } /* * If there's a BPF listener, bounce a copy of this frame * to him. */ BPF_MTAP(ifp, m_head); queued++; } if (queued == 0) return; /* Flush the TX descriptors */ bus_dmamap_sync(sc->rl_ldata.rl_tx_list_tag, sc->rl_ldata.rl_tx_list_map, BUS_DMASYNC_PREWRITE|BUS_DMASYNC_PREREAD); sc->rl_ldata.rl_tx_prodidx = idx; /* * RealTek put the TX poll request register in a different * location on the 8169 gigE chip. I don't know why. */ if (sc->rl_type == RL_8169) CSR_WRITE_2(sc, RL_GTXSTART, RL_TXSTART_START); else CSR_WRITE_2(sc, RL_TXSTART, RL_TXSTART_START); /* * Use the countdown timer for interrupt moderation. * 'TX done' interrupts are disabled. Instead, we reset the * countdown timer, which will begin counting until it hits * the value in the TIMERINT register, and then trigger an * interrupt. Each time we write to the TIMERCNT register, * the timer count is reset to 0. */ CSR_WRITE_4(sc, RL_TIMERCNT, 1); /* * Set a timeout in case the chip goes out to lunch. */ ifp->if_timer = 5; } static void re_init(xsc) void *xsc; { struct rl_softc *sc = xsc; RL_LOCK(sc); re_init_locked(sc); RL_UNLOCK(sc); } static void re_init_locked(sc) struct rl_softc *sc; { struct ifnet *ifp = sc->rl_ifp; struct mii_data *mii; u_int32_t rxcfg = 0; RL_LOCK_ASSERT(sc); mii = device_get_softc(sc->rl_miibus); /* * Cancel pending I/O and free all RX/TX buffers. */ re_stop(sc); /* * Enable C+ RX and TX mode, as well as VLAN stripping and * RX checksum offload. We must configure the C+ register * before all others. */ CSR_WRITE_2(sc, RL_CPLUS_CMD, RL_CPLUSCMD_RXENB| RL_CPLUSCMD_TXENB|RL_CPLUSCMD_PCI_MRW| RL_CPLUSCMD_VLANSTRIP| (ifp->if_capenable & IFCAP_RXCSUM ? RL_CPLUSCMD_RXCSUM_ENB : 0)); /* * Init our MAC address. Even though the chipset * documentation doesn't mention it, we need to enter "Config * register write enable" mode to modify the ID registers. */ CSR_WRITE_1(sc, RL_EECMD, RL_EEMODE_WRITECFG); CSR_WRITE_STREAM_4(sc, RL_IDR0, *(u_int32_t *)(&IFP2ENADDR(sc->rl_ifp)[0])); CSR_WRITE_STREAM_4(sc, RL_IDR4, *(u_int32_t *)(&IFP2ENADDR(sc->rl_ifp)[4])); CSR_WRITE_1(sc, RL_EECMD, RL_EEMODE_OFF); /* * For C+ mode, initialize the RX descriptors and mbufs. */ re_rx_list_init(sc); re_tx_list_init(sc); /* * Enable transmit and receive. */ CSR_WRITE_1(sc, RL_COMMAND, RL_CMD_TX_ENB|RL_CMD_RX_ENB); /* * Set the initial TX and RX configuration. */ if (sc->rl_testmode) { if (sc->rl_type == RL_8169) CSR_WRITE_4(sc, RL_TXCFG, RL_TXCFG_CONFIG|RL_LOOPTEST_ON); else CSR_WRITE_4(sc, RL_TXCFG, RL_TXCFG_CONFIG|RL_LOOPTEST_ON_CPLUS); } else CSR_WRITE_4(sc, RL_TXCFG, RL_TXCFG_CONFIG); CSR_WRITE_4(sc, RL_RXCFG, RL_RXCFG_CONFIG); /* Set the individual bit to receive frames for this host only. */ rxcfg = CSR_READ_4(sc, RL_RXCFG); rxcfg |= RL_RXCFG_RX_INDIV; /* If we want promiscuous mode, set the allframes bit. */ if (ifp->if_flags & IFF_PROMISC) rxcfg |= RL_RXCFG_RX_ALLPHYS; else rxcfg &= ~RL_RXCFG_RX_ALLPHYS; CSR_WRITE_4(sc, RL_RXCFG, rxcfg); /* * Set capture broadcast bit to capture broadcast frames. */ if (ifp->if_flags & IFF_BROADCAST) rxcfg |= RL_RXCFG_RX_BROAD; else rxcfg &= ~RL_RXCFG_RX_BROAD; CSR_WRITE_4(sc, RL_RXCFG, rxcfg); /* * Program the multicast filter, if necessary. */ re_setmulti(sc); #ifdef DEVICE_POLLING /* * Disable interrupts if we are polling. */ if (ifp->if_flags & IFF_POLLING) CSR_WRITE_2(sc, RL_IMR, 0); else /* otherwise ... */ #endif /* DEVICE_POLLING */ /* * Enable interrupts. */ if (sc->rl_testmode) CSR_WRITE_2(sc, RL_IMR, 0); else CSR_WRITE_2(sc, RL_IMR, RL_INTRS_CPLUS); /* Set initial TX threshold */ sc->rl_txthresh = RL_TX_THRESH_INIT; /* Start RX/TX process. */ CSR_WRITE_4(sc, RL_MISSEDPKT, 0); #ifdef notdef /* Enable receiver and transmitter. */ CSR_WRITE_1(sc, RL_COMMAND, RL_CMD_TX_ENB|RL_CMD_RX_ENB); #endif /* * Load the addresses of the RX and TX lists into the chip. */ CSR_WRITE_4(sc, RL_RXLIST_ADDR_HI, RL_ADDR_HI(sc->rl_ldata.rl_rx_list_addr)); CSR_WRITE_4(sc, RL_RXLIST_ADDR_LO, RL_ADDR_LO(sc->rl_ldata.rl_rx_list_addr)); CSR_WRITE_4(sc, RL_TXLIST_ADDR_HI, RL_ADDR_HI(sc->rl_ldata.rl_tx_list_addr)); CSR_WRITE_4(sc, RL_TXLIST_ADDR_LO, RL_ADDR_LO(sc->rl_ldata.rl_tx_list_addr)); CSR_WRITE_1(sc, RL_EARLY_TX_THRESH, 16); /* * Initialize the timer interrupt register so that * a timer interrupt will be generated once the timer * reaches a certain number of ticks. The timer is * reloaded on each transmit. This gives us TX interrupt * moderation, which dramatically improves TX frame rate. */ if (sc->rl_type == RL_8169) CSR_WRITE_4(sc, RL_TIMERINT_8169, 0x800); else CSR_WRITE_4(sc, RL_TIMERINT, 0x400); /* * For 8169 gigE NICs, set the max allowed RX packet * size so we can receive jumbo frames. */ if (sc->rl_type == RL_8169) CSR_WRITE_2(sc, RL_MAXRXPKTLEN, 16383); if (sc->rl_testmode) return; mii_mediachg(mii); CSR_WRITE_1(sc, RL_CFG1, RL_CFG1_DRVLOAD|RL_CFG1_FULLDUPLEX); ifp->if_flags |= IFF_RUNNING; ifp->if_flags &= ~IFF_OACTIVE; sc->rl_stat_ch = timeout(re_tick, sc, hz); } /* * Set media options. */ static int re_ifmedia_upd(ifp) struct ifnet *ifp; { struct rl_softc *sc; struct mii_data *mii; sc = ifp->if_softc; mii = device_get_softc(sc->rl_miibus); mii_mediachg(mii); return (0); } /* * Report current media status. */ static void re_ifmedia_sts(ifp, ifmr) struct ifnet *ifp; struct ifmediareq *ifmr; { struct rl_softc *sc; struct mii_data *mii; sc = ifp->if_softc; mii = device_get_softc(sc->rl_miibus); mii_pollstat(mii); ifmr->ifm_active = mii->mii_media_active; ifmr->ifm_status = mii->mii_media_status; } static int re_ioctl(ifp, command, data) struct ifnet *ifp; u_long command; caddr_t data; { struct rl_softc *sc = ifp->if_softc; struct ifreq *ifr = (struct ifreq *) data; struct mii_data *mii; int error = 0; switch (command) { case SIOCSIFMTU: if (ifr->ifr_mtu > RL_JUMBO_MTU) error = EINVAL; ifp->if_mtu = ifr->ifr_mtu; break; case SIOCSIFFLAGS: RL_LOCK(sc); if (ifp->if_flags & IFF_UP) re_init_locked(sc); else if (ifp->if_flags & IFF_RUNNING) re_stop(sc); RL_UNLOCK(sc); error = 0; break; case SIOCADDMULTI: case SIOCDELMULTI: RL_LOCK(sc); re_setmulti(sc); RL_UNLOCK(sc); error = 0; break; case SIOCGIFMEDIA: case SIOCSIFMEDIA: mii = device_get_softc(sc->rl_miibus); error = ifmedia_ioctl(ifp, ifr, &mii->mii_media, command); break; case SIOCSIFCAP: ifp->if_capenable &= ~(IFCAP_HWCSUM | IFCAP_POLLING); ifp->if_capenable |= ifr->ifr_reqcap & (IFCAP_HWCSUM | IFCAP_POLLING); if (ifp->if_capenable & IFCAP_TXCSUM) ifp->if_hwassist = RE_CSUM_FEATURES; else ifp->if_hwassist = 0; if (ifp->if_flags & IFF_RUNNING) re_init(sc); break; default: error = ether_ioctl(ifp, command, data); break; } return (error); } static void re_watchdog(ifp) struct ifnet *ifp; { struct rl_softc *sc; sc = ifp->if_softc; RL_LOCK(sc); printf("re%d: watchdog timeout\n", sc->rl_unit); ifp->if_oerrors++; re_txeof(sc); re_rxeof(sc); re_init_locked(sc); RL_UNLOCK(sc); } /* * Stop the adapter and free any mbufs allocated to the * RX and TX lists. */ static void re_stop(sc) struct rl_softc *sc; { register int i; struct ifnet *ifp; RL_LOCK_ASSERT(sc); ifp = sc->rl_ifp; ifp->if_timer = 0; untimeout(re_tick, sc, sc->rl_stat_ch); ifp->if_flags &= ~(IFF_RUNNING | IFF_OACTIVE); #ifdef DEVICE_POLLING ether_poll_deregister(ifp); #endif /* DEVICE_POLLING */ CSR_WRITE_1(sc, RL_COMMAND, 0x00); CSR_WRITE_2(sc, RL_IMR, 0x0000); if (sc->rl_head != NULL) { m_freem(sc->rl_head); sc->rl_head = sc->rl_tail = NULL; } /* Free the TX list buffers. */ for (i = 0; i < RL_TX_DESC_CNT; i++) { if (sc->rl_ldata.rl_tx_mbuf[i] != NULL) { bus_dmamap_unload(sc->rl_ldata.rl_mtag, sc->rl_ldata.rl_tx_dmamap[i]); m_freem(sc->rl_ldata.rl_tx_mbuf[i]); sc->rl_ldata.rl_tx_mbuf[i] = NULL; } } /* Free the RX list buffers. */ for (i = 0; i < RL_RX_DESC_CNT; i++) { if (sc->rl_ldata.rl_rx_mbuf[i] != NULL) { bus_dmamap_unload(sc->rl_ldata.rl_mtag, sc->rl_ldata.rl_rx_dmamap[i]); m_freem(sc->rl_ldata.rl_rx_mbuf[i]); sc->rl_ldata.rl_rx_mbuf[i] = NULL; } } } /* * Device suspend routine. Stop the interface and save some PCI * settings in case the BIOS doesn't restore them properly on * resume. */ static int re_suspend(dev) device_t dev; { struct rl_softc *sc; sc = device_get_softc(dev); RL_LOCK(sc); re_stop(sc); sc->suspended = 1; RL_UNLOCK(sc); return (0); } /* * Device resume routine. Restore some PCI settings in case the BIOS * doesn't, re-enable busmastering, and restart the interface if * appropriate. */ static int re_resume(dev) device_t dev; { struct rl_softc *sc; struct ifnet *ifp; sc = device_get_softc(dev); RL_LOCK(sc); ifp = sc->rl_ifp; /* reinitialize interface if necessary */ if (ifp->if_flags & IFF_UP) re_init_locked(sc); sc->suspended = 0; RL_UNLOCK(sc); return (0); } /* * Stop all chip I/O so that the kernel's probe routines don't * get confused by errant DMAs when rebooting. */ static void re_shutdown(dev) device_t dev; { struct rl_softc *sc; sc = device_get_softc(dev); RL_LOCK(sc); re_stop(sc); RL_UNLOCK(sc); } diff --git a/sys/pci/if_rlreg.h b/sys/pci/if_rlreg.h index ba571c5fd8cb..b8f758806997 100644 --- a/sys/pci/if_rlreg.h +++ b/sys/pci/if_rlreg.h @@ -1,901 +1,906 @@ /*- * Copyright (c) 1997, 1998-2003 * Bill Paul . All rights reserved. * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * 1. Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in the * documentation and/or other materials provided with the distribution. * 3. All advertising materials mentioning features or use of this software * must display the following acknowledgement: * This product includes software developed by Bill Paul. * 4. Neither the name of the author nor the names of any co-contributors * may be used to endorse or promote products derived from this software * without specific prior written permission. * * THIS SOFTWARE IS PROVIDED BY Bill Paul AND CONTRIBUTORS ``AS IS'' AND * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE * ARE DISCLAIMED. IN NO EVENT SHALL Bill Paul OR THE VOICES IN HIS HEAD * BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF * THE POSSIBILITY OF SUCH DAMAGE. * * $FreeBSD$ */ /* * RealTek 8129/8139 register offsets */ #define RL_IDR0 0x0000 /* ID register 0 (station addr) */ #define RL_IDR1 0x0001 /* Must use 32-bit accesses (?) */ #define RL_IDR2 0x0002 #define RL_IDR3 0x0003 #define RL_IDR4 0x0004 #define RL_IDR5 0x0005 /* 0006-0007 reserved */ #define RL_MAR0 0x0008 /* Multicast hash table */ #define RL_MAR1 0x0009 #define RL_MAR2 0x000A #define RL_MAR3 0x000B #define RL_MAR4 0x000C #define RL_MAR5 0x000D #define RL_MAR6 0x000E #define RL_MAR7 0x000F #define RL_TXSTAT0 0x0010 /* status of TX descriptor 0 */ #define RL_TXSTAT1 0x0014 /* status of TX descriptor 1 */ #define RL_TXSTAT2 0x0018 /* status of TX descriptor 2 */ #define RL_TXSTAT3 0x001C /* status of TX descriptor 3 */ #define RL_TXADDR0 0x0020 /* address of TX descriptor 0 */ #define RL_TXADDR1 0x0024 /* address of TX descriptor 1 */ #define RL_TXADDR2 0x0028 /* address of TX descriptor 2 */ #define RL_TXADDR3 0x002C /* address of TX descriptor 3 */ #define RL_RXADDR 0x0030 /* RX ring start address */ #define RL_RX_EARLY_BYTES 0x0034 /* RX early byte count */ #define RL_RX_EARLY_STAT 0x0036 /* RX early status */ #define RL_COMMAND 0x0037 /* command register */ #define RL_CURRXADDR 0x0038 /* current address of packet read */ #define RL_CURRXBUF 0x003A /* current RX buffer address */ #define RL_IMR 0x003C /* interrupt mask register */ #define RL_ISR 0x003E /* interrupt status register */ #define RL_TXCFG 0x0040 /* transmit config */ #define RL_RXCFG 0x0044 /* receive config */ #define RL_TIMERCNT 0x0048 /* timer count register */ #define RL_MISSEDPKT 0x004C /* missed packet counter */ #define RL_EECMD 0x0050 /* EEPROM command register */ #define RL_CFG0 0x0051 /* config register #0 */ #define RL_CFG1 0x0052 /* config register #1 */ /* 0053-0057 reserved */ #define RL_MEDIASTAT 0x0058 /* media status register (8139) */ /* 0059-005A reserved */ #define RL_MII 0x005A /* 8129 chip only */ #define RL_HALTCLK 0x005B #define RL_MULTIINTR 0x005C /* multiple interrupt */ #define RL_PCIREV 0x005E /* PCI revision value */ /* 005F reserved */ #define RL_TXSTAT_ALL 0x0060 /* TX status of all descriptors */ /* Direct PHY access registers only available on 8139 */ #define RL_BMCR 0x0062 /* PHY basic mode control */ #define RL_BMSR 0x0064 /* PHY basic mode status */ #define RL_ANAR 0x0066 /* PHY autoneg advert */ #define RL_LPAR 0x0068 /* PHY link partner ability */ #define RL_ANER 0x006A /* PHY autoneg expansion */ #define RL_DISCCNT 0x006C /* disconnect counter */ #define RL_FALSECAR 0x006E /* false carrier counter */ #define RL_NWAYTST 0x0070 /* NWAY test register */ #define RL_RX_ER 0x0072 /* RX_ER counter */ #define RL_CSCFG 0x0074 /* CS configuration register */ /* * When operating in special C+ mode, some of the registers in an * 8139C+ chip have different definitions. These are also used for * the 8169 gigE chip. */ #define RL_DUMPSTATS_LO 0x0010 /* counter dump command register */ #define RL_DUMPSTATS_HI 0x0014 /* counter dump command register */ #define RL_TXLIST_ADDR_LO 0x0020 /* 64 bits, 256 byte alignment */ #define RL_TXLIST_ADDR_HI 0x0024 /* 64 bits, 256 byte alignment */ #define RL_TXLIST_ADDR_HPRIO_LO 0x0028 /* 64 bits, 256 byte alignment */ #define RL_TXLIST_ADDR_HPRIO_HI 0x002C /* 64 bits, 256 byte alignment */ #define RL_CFG2 0x0053 #define RL_TIMERINT 0x0054 /* interrupt on timer expire */ #define RL_TXSTART 0x00D9 /* 8 bits */ #define RL_CPLUS_CMD 0x00E0 /* 16 bits */ #define RL_RXLIST_ADDR_LO 0x00E4 /* 64 bits, 256 byte alignment */ #define RL_RXLIST_ADDR_HI 0x00E8 /* 64 bits, 256 byte alignment */ #define RL_EARLY_TX_THRESH 0x00EC /* 8 bits */ /* * Registers specific to the 8169 gigE chip */ #define RL_TIMERINT_8169 0x0058 /* different offset than 8139 */ #define RL_PHYAR 0x0060 #define RL_TBICSR 0x0064 #define RL_TBI_ANAR 0x0068 #define RL_TBI_LPAR 0x006A #define RL_GMEDIASTAT 0x006C /* 8 bits */ #define RL_MAXRXPKTLEN 0x00DA /* 16 bits, chip multiplies by 8 */ #define RL_GTXSTART 0x0038 /* 16 bits */ /* * TX config register bits */ #define RL_TXCFG_CLRABRT 0x00000001 /* retransmit aborted pkt */ #define RL_TXCFG_MAXDMA 0x00000700 /* max DMA burst size */ #define RL_TXCFG_CRCAPPEND 0x00010000 /* CRC append (0 = yes) */ #define RL_TXCFG_LOOPBKTST 0x00060000 /* loopback test */ #define RL_TXCFG_IFG2 0x00080000 /* 8169 only */ #define RL_TXCFG_IFG 0x03000000 /* interframe gap */ #define RL_TXCFG_HWREV 0x7CC00000 #define RL_LOOPTEST_OFF 0x00000000 #define RL_LOOPTEST_ON 0x00020000 #define RL_LOOPTEST_ON_CPLUS 0x00060000 #define RL_HWREV_8169 0x00000000 #define RL_HWREV_8169S 0x04000000 #define RL_HWREV_8169SB 0x10000000 #define RL_HWREV_8110S 0x00800000 #define RL_HWREV_8139 0x60000000 #define RL_HWREV_8139A 0x70000000 #define RL_HWREV_8139AG 0x70800000 #define RL_HWREV_8139B 0x78000000 #define RL_HWREV_8130 0x7C000000 #define RL_HWREV_8139C 0x74000000 #define RL_HWREV_8139D 0x74400000 #define RL_HWREV_8139CPLUS 0x74800000 #define RL_HWREV_8101 0x74c00000 #define RL_HWREV_8100 0x78800000 #define RL_TXDMA_16BYTES 0x00000000 #define RL_TXDMA_32BYTES 0x00000100 #define RL_TXDMA_64BYTES 0x00000200 #define RL_TXDMA_128BYTES 0x00000300 #define RL_TXDMA_256BYTES 0x00000400 #define RL_TXDMA_512BYTES 0x00000500 #define RL_TXDMA_1024BYTES 0x00000600 #define RL_TXDMA_2048BYTES 0x00000700 /* * Transmit descriptor status register bits. */ #define RL_TXSTAT_LENMASK 0x00001FFF #define RL_TXSTAT_OWN 0x00002000 #define RL_TXSTAT_TX_UNDERRUN 0x00004000 #define RL_TXSTAT_TX_OK 0x00008000 #define RL_TXSTAT_EARLY_THRESH 0x003F0000 #define RL_TXSTAT_COLLCNT 0x0F000000 #define RL_TXSTAT_CARR_HBEAT 0x10000000 #define RL_TXSTAT_OUTOFWIN 0x20000000 #define RL_TXSTAT_TXABRT 0x40000000 #define RL_TXSTAT_CARRLOSS 0x80000000 /* * Interrupt status register bits. */ #define RL_ISR_RX_OK 0x0001 #define RL_ISR_RX_ERR 0x0002 #define RL_ISR_TX_OK 0x0004 #define RL_ISR_TX_ERR 0x0008 #define RL_ISR_RX_OVERRUN 0x0010 #define RL_ISR_PKT_UNDERRUN 0x0020 #define RL_ISR_LINKCHG 0x0020 /* 8169 only */ #define RL_ISR_FIFO_OFLOW 0x0040 /* 8139 only */ #define RL_ISR_TX_DESC_UNAVAIL 0x0080 /* C+ only */ #define RL_ISR_SWI 0x0100 /* C+ only */ #define RL_ISR_CABLE_LEN_CHGD 0x2000 #define RL_ISR_PCS_TIMEOUT 0x4000 /* 8129 only */ #define RL_ISR_TIMEOUT_EXPIRED 0x4000 #define RL_ISR_SYSTEM_ERR 0x8000 #define RL_INTRS \ (RL_ISR_TX_OK|RL_ISR_RX_OK|RL_ISR_RX_ERR|RL_ISR_TX_ERR| \ RL_ISR_RX_OVERRUN|RL_ISR_PKT_UNDERRUN|RL_ISR_FIFO_OFLOW| \ RL_ISR_PCS_TIMEOUT|RL_ISR_SYSTEM_ERR) #define RL_INTRS_CPLUS \ (RL_ISR_RX_OK|RL_ISR_RX_ERR|RL_ISR_TX_ERR| \ RL_ISR_RX_OVERRUN|RL_ISR_PKT_UNDERRUN|RL_ISR_FIFO_OFLOW| \ RL_ISR_PCS_TIMEOUT|RL_ISR_SYSTEM_ERR|RL_ISR_TIMEOUT_EXPIRED) /* * Media status register. (8139 only) */ #define RL_MEDIASTAT_RXPAUSE 0x01 #define RL_MEDIASTAT_TXPAUSE 0x02 #define RL_MEDIASTAT_LINK 0x04 #define RL_MEDIASTAT_SPEED10 0x08 #define RL_MEDIASTAT_RXFLOWCTL 0x40 /* duplex mode */ #define RL_MEDIASTAT_TXFLOWCTL 0x80 /* duplex mode */ /* * Receive config register. */ #define RL_RXCFG_RX_ALLPHYS 0x00000001 /* accept all nodes */ #define RL_RXCFG_RX_INDIV 0x00000002 /* match filter */ #define RL_RXCFG_RX_MULTI 0x00000004 /* accept all multicast */ #define RL_RXCFG_RX_BROAD 0x00000008 /* accept all broadcast */ #define RL_RXCFG_RX_RUNT 0x00000010 #define RL_RXCFG_RX_ERRPKT 0x00000020 #define RL_RXCFG_WRAP 0x00000080 #define RL_RXCFG_MAXDMA 0x00000700 #define RL_RXCFG_BUFSZ 0x00001800 #define RL_RXCFG_FIFOTHRESH 0x0000E000 #define RL_RXCFG_EARLYTHRESH 0x07000000 #define RL_RXDMA_16BYTES 0x00000000 #define RL_RXDMA_32BYTES 0x00000100 #define RL_RXDMA_64BYTES 0x00000200 #define RL_RXDMA_128BYTES 0x00000300 #define RL_RXDMA_256BYTES 0x00000400 #define RL_RXDMA_512BYTES 0x00000500 #define RL_RXDMA_1024BYTES 0x00000600 #define RL_RXDMA_UNLIMITED 0x00000700 #define RL_RXBUF_8 0x00000000 #define RL_RXBUF_16 0x00000800 #define RL_RXBUF_32 0x00001000 #define RL_RXBUF_64 0x00001800 #define RL_RXFIFO_16BYTES 0x00000000 #define RL_RXFIFO_32BYTES 0x00002000 #define RL_RXFIFO_64BYTES 0x00004000 #define RL_RXFIFO_128BYTES 0x00006000 #define RL_RXFIFO_256BYTES 0x00008000 #define RL_RXFIFO_512BYTES 0x0000A000 #define RL_RXFIFO_1024BYTES 0x0000C000 #define RL_RXFIFO_NOTHRESH 0x0000E000 /* * Bits in RX status header (included with RX'ed packet * in ring buffer). */ #define RL_RXSTAT_RXOK 0x00000001 #define RL_RXSTAT_ALIGNERR 0x00000002 #define RL_RXSTAT_CRCERR 0x00000004 #define RL_RXSTAT_GIANT 0x00000008 #define RL_RXSTAT_RUNT 0x00000010 #define RL_RXSTAT_BADSYM 0x00000020 #define RL_RXSTAT_BROAD 0x00002000 #define RL_RXSTAT_INDIV 0x00004000 #define RL_RXSTAT_MULTI 0x00008000 #define RL_RXSTAT_LENMASK 0xFFFF0000 #define RL_RXSTAT_UNFINISHED 0xFFF0 /* DMA still in progress */ /* * Command register. */ #define RL_CMD_EMPTY_RXBUF 0x0001 #define RL_CMD_TX_ENB 0x0004 #define RL_CMD_RX_ENB 0x0008 #define RL_CMD_RESET 0x0010 /* * EEPROM control register */ #define RL_EE_DATAOUT 0x01 /* Data out */ #define RL_EE_DATAIN 0x02 /* Data in */ #define RL_EE_CLK 0x04 /* clock */ #define RL_EE_SEL 0x08 /* chip select */ #define RL_EE_MODE (0x40|0x80) #define RL_EEMODE_OFF 0x00 #define RL_EEMODE_AUTOLOAD 0x40 #define RL_EEMODE_PROGRAM 0x80 #define RL_EEMODE_WRITECFG (0x80|0x40) /* 9346 EEPROM commands */ #define RL_EECMD_WRITE 0x140 #define RL_EECMD_READ_6BIT 0x180 #define RL_EECMD_READ_8BIT 0x600 #define RL_EECMD_ERASE 0x1c0 #define RL_EE_ID 0x00 #define RL_EE_PCI_VID 0x01 #define RL_EE_PCI_DID 0x02 /* Location of station address inside EEPROM */ #define RL_EE_EADDR 0x07 /* * MII register (8129 only) */ #define RL_MII_CLK 0x01 #define RL_MII_DATAIN 0x02 #define RL_MII_DATAOUT 0x04 #define RL_MII_DIR 0x80 /* 0 == input, 1 == output */ /* * Config 0 register */ #define RL_CFG0_ROM0 0x01 #define RL_CFG0_ROM1 0x02 #define RL_CFG0_ROM2 0x04 #define RL_CFG0_PL0 0x08 #define RL_CFG0_PL1 0x10 #define RL_CFG0_10MBPS 0x20 /* 10 Mbps internal mode */ #define RL_CFG0_PCS 0x40 #define RL_CFG0_SCR 0x80 /* * Config 1 register */ #define RL_CFG1_PWRDWN 0x01 #define RL_CFG1_SLEEP 0x02 #define RL_CFG1_IOMAP 0x04 #define RL_CFG1_MEMMAP 0x08 #define RL_CFG1_RSVD 0x10 #define RL_CFG1_DRVLOAD 0x20 #define RL_CFG1_LED0 0x40 #define RL_CFG1_FULLDUPLEX 0x40 /* 8129 only */ #define RL_CFG1_LED1 0x80 /* * 8139C+ register definitions */ /* RL_DUMPSTATS_LO register */ #define RL_DUMPSTATS_START 0x00000008 /* Transmit start register */ #define RL_TXSTART_SWI 0x01 /* generate TX interrupt */ #define RL_TXSTART_START 0x40 /* start normal queue transmit */ #define RL_TXSTART_HPRIO_START 0x80 /* start hi prio queue transmit */ /* * Config 2 register, 8139C+/8169/8169S/8110S only */ #define RL_CFG2_BUSFREQ 0x07 #define RL_CFG2_BUSWIDTH 0x08 #define RL_CFG2_AUXPWRSTS 0x10 #define RL_BUSFREQ_33MHZ 0x00 #define RL_BUSFREQ_66MHZ 0x01 #define RL_BUSWIDTH_32BITS 0x00 #define RL_BUSWIDTH_64BITS 0x08 /* C+ mode command register */ #define RL_CPLUSCMD_TXENB 0x0001 /* enable C+ transmit mode */ #define RL_CPLUSCMD_RXENB 0x0002 /* enable C+ receive mode */ #define RL_CPLUSCMD_PCI_MRW 0x0008 /* enable PCI multi-read/write */ #define RL_CPLUSCMD_PCI_DAC 0x0010 /* PCI dual-address cycle only */ #define RL_CPLUSCMD_RXCSUM_ENB 0x0020 /* enable RX checksum offload */ #define RL_CPLUSCMD_VLANSTRIP 0x0040 /* enable VLAN tag stripping */ /* C+ early transmit threshold */ #define RL_EARLYTXTHRESH_CNT 0x003F /* byte count times 8 */ /* * Gigabit PHY access register (8169 only) */ #define RL_PHYAR_PHYDATA 0x0000FFFF #define RL_PHYAR_PHYREG 0x001F0000 #define RL_PHYAR_BUSY 0x80000000 /* * Gigabit media status (8169 only) */ #define RL_GMEDIASTAT_FDX 0x01 /* full duplex */ #define RL_GMEDIASTAT_LINK 0x02 /* link up */ #define RL_GMEDIASTAT_10MBPS 0x04 /* 10mps link */ #define RL_GMEDIASTAT_100MBPS 0x08 /* 100mbps link */ #define RL_GMEDIASTAT_1000MBPS 0x10 /* gigE link */ #define RL_GMEDIASTAT_RXFLOW 0x20 /* RX flow control on */ #define RL_GMEDIASTAT_TXFLOW 0x40 /* TX flow control on */ #define RL_GMEDIASTAT_TBI 0x80 /* TBI enabled */ /* * The RealTek doesn't use a fragment-based descriptor mechanism. * Instead, there are only four register sets, each or which represents * one 'descriptor.' Basically, each TX descriptor is just a contiguous * packet buffer (32-bit aligned!) and we place the buffer addresses in * the registers so the chip knows where they are. * * We can sort of kludge together the same kind of buffer management * used in previous drivers, but we have to do buffer copies almost all * the time, so it doesn't really buy us much. * * For reception, there's just one large buffer where the chip stores * all received packets. */ #define RL_RX_BUF_SZ RL_RXBUF_64 #define RL_RXBUFLEN (1 << ((RL_RX_BUF_SZ >> 11) + 13)) #define RL_TX_LIST_CNT 4 #define RL_MIN_FRAMELEN 60 #define RL_TXTHRESH(x) ((x) << 11) #define RL_TX_THRESH_INIT 96 #define RL_RX_FIFOTHRESH RL_RXFIFO_NOTHRESH #define RL_RX_MAXDMA RL_RXDMA_UNLIMITED #define RL_TX_MAXDMA RL_TXDMA_2048BYTES #define RL_RXCFG_CONFIG (RL_RX_FIFOTHRESH|RL_RX_MAXDMA|RL_RX_BUF_SZ) #define RL_TXCFG_CONFIG (RL_TXCFG_IFG|RL_TX_MAXDMA) #define RL_ETHER_ALIGN 2 struct rl_chain_data { uint16_t cur_rx; uint8_t *rl_rx_buf; uint8_t *rl_rx_buf_ptr; bus_dmamap_t rl_rx_dmamap; struct mbuf *rl_tx_chain[RL_TX_LIST_CNT]; bus_dmamap_t rl_tx_dmamap[RL_TX_LIST_CNT]; uint8_t last_tx; uint8_t cur_tx; }; #define RL_INC(x) (x = (x + 1) % RL_TX_LIST_CNT) #define RL_CUR_TXADDR(x) ((x->rl_cdata.cur_tx * 4) + RL_TXADDR0) #define RL_CUR_TXSTAT(x) ((x->rl_cdata.cur_tx * 4) + RL_TXSTAT0) #define RL_CUR_TXMBUF(x) (x->rl_cdata.rl_tx_chain[x->rl_cdata.cur_tx]) #define RL_CUR_DMAMAP(x) (x->rl_cdata.rl_tx_dmamap[x->rl_cdata.cur_tx]) #define RL_LAST_TXADDR(x) ((x->rl_cdata.last_tx * 4) + RL_TXADDR0) #define RL_LAST_TXSTAT(x) ((x->rl_cdata.last_tx * 4) + RL_TXSTAT0) #define RL_LAST_TXMBUF(x) (x->rl_cdata.rl_tx_chain[x->rl_cdata.last_tx]) #define RL_LAST_DMAMAP(x) (x->rl_cdata.rl_tx_dmamap[x->rl_cdata.last_tx]) struct rl_type { uint16_t rl_vid; uint16_t rl_did; int rl_basetype; char *rl_name; }; struct rl_hwrev { uint32_t rl_rev; int rl_type; char *rl_desc; }; struct rl_mii_frame { uint8_t mii_stdelim; uint8_t mii_opcode; uint8_t mii_phyaddr; uint8_t mii_regaddr; uint8_t mii_turnaround; uint16_t mii_data; }; /* * MII constants */ #define RL_MII_STARTDELIM 0x01 #define RL_MII_READOP 0x02 #define RL_MII_WRITEOP 0x01 #define RL_MII_TURNAROUND 0x02 #define RL_8129 1 #define RL_8139 2 #define RL_8139CPLUS 3 #define RL_8169 4 #define RL_ISCPLUS(x) ((x)->rl_type == RL_8139CPLUS || \ (x)->rl_type == RL_8169) /* * The 8139C+ and 8160 gigE chips support descriptor-based TX * and RX. In fact, they even support TCP large send. Descriptors * must be allocated in contiguous blocks that are aligned on a * 256-byte boundary. The rings can hold a maximum of 64 descriptors. */ /* * RX/TX descriptor definition. When large send mode is enabled, the * lower 11 bits of the TX rl_cmd word are used to hold the MSS, and * the checksum offload bits are disabled. The structure layout is * the same for RX and TX descriptors */ struct rl_desc { uint32_t rl_cmdstat; uint32_t rl_vlanctl; uint32_t rl_bufaddr_lo; uint32_t rl_bufaddr_hi; }; #define RL_TDESC_CMD_FRAGLEN 0x0000FFFF #define RL_TDESC_CMD_TCPCSUM 0x00010000 /* TCP checksum enable */ #define RL_TDESC_CMD_UDPCSUM 0x00020000 /* UDP checksum enable */ #define RL_TDESC_CMD_IPCSUM 0x00040000 /* IP header checksum enable */ #define RL_TDESC_CMD_MSSVAL 0x07FF0000 /* Large send MSS value */ #define RL_TDESC_CMD_LGSEND 0x08000000 /* TCP large send enb */ #define RL_TDESC_CMD_EOF 0x10000000 /* end of frame marker */ #define RL_TDESC_CMD_SOF 0x20000000 /* start of frame marker */ #define RL_TDESC_CMD_EOR 0x40000000 /* end of ring marker */ #define RL_TDESC_CMD_OWN 0x80000000 /* chip owns descriptor */ #define RL_TDESC_VLANCTL_TAG 0x00020000 /* Insert VLAN tag */ #define RL_TDESC_VLANCTL_DATA 0x0000FFFF /* TAG data */ /* * Error bits are valid only on the last descriptor of a frame * (i.e. RL_TDESC_CMD_EOF == 1) */ #define RL_TDESC_STAT_COLCNT 0x000F0000 /* collision count */ #define RL_TDESC_STAT_EXCESSCOL 0x00100000 /* excessive collisions */ #define RL_TDESC_STAT_LINKFAIL 0x00200000 /* link faulure */ #define RL_TDESC_STAT_OWINCOL 0x00400000 /* out-of-window collision */ #define RL_TDESC_STAT_TXERRSUM 0x00800000 /* transmit error summary */ #define RL_TDESC_STAT_UNDERRUN 0x02000000 /* TX underrun occured */ #define RL_TDESC_STAT_OWN 0x80000000 /* * RX descriptor cmd/vlan definitions */ #define RL_RDESC_CMD_EOR 0x40000000 #define RL_RDESC_CMD_OWN 0x80000000 #define RL_RDESC_CMD_BUFLEN 0x00001FFF #define RL_RDESC_STAT_OWN 0x80000000 #define RL_RDESC_STAT_EOR 0x40000000 #define RL_RDESC_STAT_SOF 0x20000000 #define RL_RDESC_STAT_EOF 0x10000000 #define RL_RDESC_STAT_FRALIGN 0x08000000 /* frame alignment error */ #define RL_RDESC_STAT_MCAST 0x04000000 /* multicast pkt received */ #define RL_RDESC_STAT_UCAST 0x02000000 /* unicast pkt received */ #define RL_RDESC_STAT_BCAST 0x01000000 /* broadcast pkt received */ #define RL_RDESC_STAT_BUFOFLOW 0x00800000 /* out of buffer space */ #define RL_RDESC_STAT_FIFOOFLOW 0x00400000 /* FIFO overrun */ #define RL_RDESC_STAT_GIANT 0x00200000 /* pkt > 4096 bytes */ #define RL_RDESC_STAT_RXERRSUM 0x00100000 /* RX error summary */ #define RL_RDESC_STAT_RUNT 0x00080000 /* runt packet received */ #define RL_RDESC_STAT_CRCERR 0x00040000 /* CRC error */ #define RL_RDESC_STAT_PROTOID 0x00030000 /* Protocol type */ #define RL_RDESC_STAT_IPSUMBAD 0x00008000 /* IP header checksum bad */ #define RL_RDESC_STAT_UDPSUMBAD 0x00004000 /* UDP checksum bad */ #define RL_RDESC_STAT_TCPSUMBAD 0x00002000 /* TCP checksum bad */ #define RL_RDESC_STAT_FRAGLEN 0x00001FFF /* RX'ed frame/frag len */ #define RL_RDESC_STAT_GFRAGLEN 0x00003FFF /* RX'ed frame/frag len */ #define RL_RDESC_STAT_ERRS (RL_RDESC_STAT_GIANT|RL_RDESC_STAT_RUNT| \ RL_RDESC_STAT_CRCERR) #define RL_RDESC_VLANCTL_TAG 0x00010000 /* VLAN tag available (rl_vlandata valid)*/ #define RL_RDESC_VLANCTL_DATA 0x0000FFFF /* TAG data */ #define RL_PROTOID_NONIP 0x00000000 #define RL_PROTOID_TCPIP 0x00010000 #define RL_PROTOID_UDPIP 0x00020000 #define RL_PROTOID_IP 0x00030000 #define RL_TCPPKT(x) (((x) & RL_RDESC_STAT_PROTOID) == \ RL_PROTOID_TCPIP) #define RL_UDPPKT(x) (((x) & RL_RDESC_STAT_PROTOID) == \ RL_PROTOID_UDPIP) /* * Statistics counter structure (8139C+ and 8169 only) */ struct rl_stats { uint32_t rl_tx_pkts_lo; uint32_t rl_tx_pkts_hi; uint32_t rl_tx_errs_lo; uint32_t rl_tx_errs_hi; uint32_t rl_tx_errs; uint16_t rl_missed_pkts; uint16_t rl_rx_framealign_errs; uint32_t rl_tx_onecoll; uint32_t rl_tx_multicolls; uint32_t rl_rx_ucasts_hi; uint32_t rl_rx_ucasts_lo; uint32_t rl_rx_bcasts_lo; uint32_t rl_rx_bcasts_hi; uint32_t rl_rx_mcasts; uint16_t rl_tx_aborts; uint16_t rl_rx_underruns; }; /* * Rx/Tx descriptor parameters (8139C+ and 8169 only) * * Tx/Rx count must be equal. Shared code like re_dma_map_desc assumes this. * Buffers must be a multiple of 8 bytes. Currently limit to 64 descriptors * due to the 8139C+. We need to put the number of descriptors in the ring * structure and use that value instead. */ #if !defined(__i386__) && !defined(__amd64__) #define RE_FIXUP_RX 1 #endif #define RL_TX_DESC_CNT 64 #define RL_RX_DESC_CNT RL_TX_DESC_CNT #define RL_RX_LIST_SZ (RL_RX_DESC_CNT * sizeof(struct rl_desc)) #define RL_TX_LIST_SZ (RL_TX_DESC_CNT * sizeof(struct rl_desc)) #define RL_RING_ALIGN 256 #define RL_IFQ_MAXLEN 512 #define RL_DESC_INC(x) (x = (x + 1) % RL_TX_DESC_CNT) #define RL_OWN(x) (le32toh((x)->rl_cmdstat) & RL_RDESC_STAT_OWN) #define RL_RXBYTES(x) (le32toh((x)->rl_cmdstat) & sc->rl_rxlenmask) #define RL_PKTSZ(x) ((x)/* >> 3*/) #ifdef RE_FIXUP_RX #define RE_ETHER_ALIGN sizeof(uint64_t) #define RE_RX_DESC_BUFLEN (MCLBYTES - RE_ETHER_ALIGN) #else #define RE_ETHER_ALIGN 0 #define RE_RX_DESC_BUFLEN MCLBYTES #endif #define RL_ADDR_LO(y) ((uint64_t) (y) & 0xFFFFFFFF) #define RL_ADDR_HI(y) ((uint64_t) (y) >> 32) /* see comment in dev/re/if_re.c */ #define RL_JUMBO_FRAMELEN 7440 #define RL_JUMBO_MTU (RL_JUMBO_FRAMELEN-ETHER_HDR_LEN-ETHER_CRC_LEN) struct rl_softc; struct rl_dmaload_arg { struct rl_softc *sc; int rl_idx; int rl_maxsegs; uint32_t rl_flags; struct rl_desc *rl_ring; }; struct rl_list_data { struct mbuf *rl_tx_mbuf[RL_TX_DESC_CNT]; struct mbuf *rl_rx_mbuf[RL_TX_DESC_CNT]; int rl_tx_prodidx; int rl_rx_prodidx; int rl_tx_considx; int rl_tx_free; bus_dmamap_t rl_tx_dmamap[RL_TX_DESC_CNT]; bus_dmamap_t rl_rx_dmamap[RL_RX_DESC_CNT]; bus_dma_tag_t rl_mtag; /* mbuf mapping tag */ bus_dma_tag_t rl_stag; /* stats mapping tag */ bus_dmamap_t rl_smap; /* stats map */ struct rl_stats *rl_stats; bus_addr_t rl_stats_addr; bus_dma_tag_t rl_rx_list_tag; bus_dmamap_t rl_rx_list_map; struct rl_desc *rl_rx_list; bus_addr_t rl_rx_list_addr; bus_dma_tag_t rl_tx_list_tag; bus_dmamap_t rl_tx_list_map; struct rl_desc *rl_tx_list; bus_addr_t rl_tx_list_addr; }; struct rl_softc { struct ifnet *rl_ifp; /* interface info */ bus_space_handle_t rl_bhandle; /* bus space handle */ bus_space_tag_t rl_btag; /* bus space tag */ struct resource *rl_res; struct resource *rl_irq; void *rl_intrhand; device_t rl_miibus; bus_dma_tag_t rl_parent_tag; bus_dma_tag_t rl_tag; uint8_t rl_unit; /* interface number */ uint8_t rl_type; int rl_eecmd_read; uint8_t rl_stats_no_timeout; int rl_txthresh; struct rl_chain_data rl_cdata; struct rl_list_data rl_ldata; struct callout_handle rl_stat_ch; struct mtx rl_mtx; struct mbuf *rl_head; struct mbuf *rl_tail; uint32_t rl_hwrev; uint32_t rl_rxlenmask; int rl_testmode; int suspended; /* 0 = normal 1 = suspended */ #ifdef DEVICE_POLLING int rxcycles; #endif }; #define RL_LOCK(_sc) mtx_lock(&(_sc)->rl_mtx) #define RL_UNLOCK(_sc) mtx_unlock(&(_sc)->rl_mtx) #define RL_LOCK_ASSERT(_sc) mtx_assert(&(_sc)->rl_mtx, MA_OWNED) /* * register space access macros */ #define CSR_WRITE_STREAM_4(sc, reg, val) \ bus_space_write_stream_4(sc->rl_btag, sc->rl_bhandle, reg, val) #define CSR_WRITE_4(sc, reg, val) \ bus_space_write_4(sc->rl_btag, sc->rl_bhandle, reg, val) #define CSR_WRITE_2(sc, reg, val) \ bus_space_write_2(sc->rl_btag, sc->rl_bhandle, reg, val) #define CSR_WRITE_1(sc, reg, val) \ bus_space_write_1(sc->rl_btag, sc->rl_bhandle, reg, val) #define CSR_READ_4(sc, reg) \ bus_space_read_4(sc->rl_btag, sc->rl_bhandle, reg) #define CSR_READ_2(sc, reg) \ bus_space_read_2(sc->rl_btag, sc->rl_bhandle, reg) #define CSR_READ_1(sc, reg) \ bus_space_read_1(sc->rl_btag, sc->rl_bhandle, reg) #define RL_TIMEOUT 1000 /* * General constants that are fun to know. * * RealTek PCI vendor ID */ #define RT_VENDORID 0x10EC /* * RealTek chip device IDs. */ #define RT_DEVICEID_8129 0x8129 #define RT_DEVICEID_8138 0x8138 #define RT_DEVICEID_8139 0x8139 #define RT_DEVICEID_8169 0x8169 #define RT_DEVICEID_8100 0x8100 #define RT_REVID_8139CPLUS 0x20 /* * Accton PCI vendor ID */ #define ACCTON_VENDORID 0x1113 /* * Accton MPX 5030/5038 device ID. */ #define ACCTON_DEVICEID_5030 0x1211 /* * Nortel PCI vendor ID */ #define NORTEL_VENDORID 0x126C /* * Delta Electronics Vendor ID. */ #define DELTA_VENDORID 0x1500 /* * Delta device IDs. */ #define DELTA_DEVICEID_8139 0x1360 /* * Addtron vendor ID. */ #define ADDTRON_VENDORID 0x4033 /* * Addtron device IDs. */ #define ADDTRON_DEVICEID_8139 0x1360 /* * D-Link vendor ID. */ #define DLINK_VENDORID 0x1186 /* * D-Link DFE-530TX+ device ID */ #define DLINK_DEVICEID_530TXPLUS 0x1300 +/* + * D-Link DFE-5280T device ID + */ +#define DLINK_DEVICEID_528T 0x4300 + /* * D-Link DFE-690TXD device ID */ #define DLINK_DEVICEID_690TXD 0x1340 /* * Corega K.K vendor ID */ #define COREGA_VENDORID 0x1259 /* * Corega FEther CB-TXD device ID */ #define COREGA_DEVICEID_FETHERCBTXD 0xa117 /* * Corega FEtherII CB-TXD device ID */ #define COREGA_DEVICEID_FETHERIICBTXD 0xa11e /* * Corega CG-LAPCIGT device ID */ #define COREGA_DEVICEID_CGLAPCIGT 0xc107 /* * Peppercon vendor ID */ #define PEPPERCON_VENDORID 0x1743 /* * Peppercon ROL-F device ID */ #define PEPPERCON_DEVICEID_ROLF 0x8139 /* * Planex Communications, Inc. vendor ID */ #define PLANEX_VENDORID 0x14ea /* * Planex FNW-3800-TX device ID */ #define PLANEX_DEVICEID_FNW3800TX 0xab07 /* * LevelOne vendor ID */ #define LEVEL1_VENDORID 0x018A /* * LevelOne FPC-0106TX devide ID */ #define LEVEL1_DEVICEID_FPC0106TX 0x0106 /* * Compaq vendor ID */ #define CP_VENDORID 0x021B /* * Edimax vendor ID */ #define EDIMAX_VENDORID 0x13D1 /* * Edimax EP-4103DL cardbus device ID */ #define EDIMAX_DEVICEID_EP4103DL 0xAB06 /* * PCI low memory base and low I/O base register, and * other PCI registers. */ #define RL_PCI_VENDOR_ID 0x00 #define RL_PCI_DEVICE_ID 0x02 #define RL_PCI_COMMAND 0x04 #define RL_PCI_STATUS 0x06 #define RL_PCI_CLASSCODE 0x09 #define RL_PCI_LATENCY_TIMER 0x0D #define RL_PCI_HEADER_TYPE 0x0E #define RL_PCI_LOIO 0x10 #define RL_PCI_LOMEM 0x14 #define RL_PCI_BIOSROM 0x30 #define RL_PCI_INTLINE 0x3C #define RL_PCI_INTPIN 0x3D #define RL_PCI_MINGNT 0x3E #define RL_PCI_MINLAT 0x0F #define RL_PCI_RESETOPT 0x48 #define RL_PCI_EEPROM_DATA 0x4C #define RL_PCI_CAPID 0x50 /* 8 bits */ #define RL_PCI_NEXTPTR 0x51 /* 8 bits */ #define RL_PCI_PWRMGMTCAP 0x52 /* 16 bits */ #define RL_PCI_PWRMGMTCTRL 0x54 /* 16 bits */ #define RL_PSTATE_MASK 0x0003 #define RL_PSTATE_D0 0x0000 #define RL_PSTATE_D1 0x0002 #define RL_PSTATE_D2 0x0002 #define RL_PSTATE_D3 0x0003 #define RL_PME_EN 0x0010 #define RL_PME_STATUS 0x8000