Changeset View
Changeset View
Standalone View
Standalone View
sys/gnu/dts/mips/RBM33G.dts
- This file was added.
/dts-v1/; | |||||
#include "mt7621.dtsi" | |||||
#include <dt-bindings/input/input.h> | |||||
#include <dt-bindings/gpio/gpio.h> | |||||
/ { | |||||
compatible = "mikrotik,rbm33g", "mediatek,mt7621-soc"; | |||||
model = "MikroTik RBM33G"; | |||||
memory@0 { | |||||
device_type = "memory"; | |||||
reg = <0x0 0x10000000>; | |||||
}; | |||||
chosen { | |||||
bootargs = "console=ttyS0,115200"; | |||||
}; | |||||
gpio-leds { | |||||
compatible = "gpio-leds"; | |||||
usr { | |||||
label = "rbm33g:green:usr"; | |||||
gpios = <&gpio0 0 GPIO_ACTIVE_HIGH>; | |||||
}; | |||||
}; | |||||
gpio-keys-polled { | |||||
compatible = "gpio-keys-polled"; | |||||
#address-cells = <1>; | |||||
#size-cells = <0>; | |||||
poll-interval = <20>; | |||||
res { | |||||
label = "res"; | |||||
gpios = <&gpio0 18 GPIO_ACTIVE_LOW>; | |||||
linux,code = <KEY_RESTART>; | |||||
}; | |||||
}; | |||||
pcie0_vcc_reg { | |||||
compatible = "regulator-fixed"; | |||||
regulator-name = "pcie0_vcc"; | |||||
regulator-min-microvolt = <3300000>; | |||||
regulator-max-microvolt = <3300000>; | |||||
gpio = <&gpio0 9 GPIO_ACTIVE_HIGH>; | |||||
enable-active-high; | |||||
regulator-boot-on; | |||||
regulator-always-on; | |||||
}; | |||||
pcie1_vcc_reg { | |||||
compatible = "regulator-fixed"; | |||||
regulator-name = "pcie1_vcc"; | |||||
regulator-min-microvolt = <3300000>; | |||||
regulator-max-microvolt = <3300000>; | |||||
gpio = <&gpio0 10 GPIO_ACTIVE_HIGH>; | |||||
enable-active-high; | |||||
regulator-boot-on; | |||||
regulator-always-on; | |||||
}; | |||||
pcie2_vcc_reg { | |||||
compatible = "regulator-fixed"; | |||||
regulator-name = "pcie2_vcc"; | |||||
regulator-min-microvolt = <3300000>; | |||||
regulator-max-microvolt = <3300000>; | |||||
gpio = <&gpio0 11 GPIO_ACTIVE_HIGH>; | |||||
enable-active-high; | |||||
regulator-boot-on; | |||||
regulator-always-on; | |||||
}; | |||||
usb_vcc_reg { | |||||
compatible = "regulator-fixed"; | |||||
regulator-name = "usb_vcc"; | |||||
regulator-min-microvolt = <5000000>; | |||||
regulator-max-microvolt = <5000000>; | |||||
gpio = <&gpio0 12 GPIO_ACTIVE_HIGH>; | |||||
enable-active-high; | |||||
regulator-always-on; | |||||
}; | |||||
}; | |||||
&spi0 { | |||||
status = "okay"; | |||||
w25q40@0 { | |||||
#address-cells = <1>; | |||||
#size-cells = <1>; | |||||
compatible = "jedec,spi-nor"; | |||||
reg = <0>; | |||||
spi-max-frequency = <3125000>; | |||||
partition@0 { | |||||
label = "routerboot"; | |||||
reg = <0x0 0xf000>; | |||||
read-only; | |||||
}; | |||||
factory: partition@f000 { | |||||
label = "factory"; | |||||
reg = <0xf000 0x71000>; | |||||
read-only; | |||||
}; | |||||
}; | |||||
w25q128@0 { | |||||
#address-cells = <1>; | |||||
#size-cells = <1>; | |||||
compatible = "jedec,spi-nor"; | |||||
reg = <1>; | |||||
spi-max-frequency = <3125000>; | |||||
partition@40000 { | |||||
label = "firmware"; | |||||
reg = <0x040000 0xFC0000>; | |||||
}; | |||||
}; | |||||
}; | |||||
ðernet { | |||||
mtd-mac-address = <&factory 0x0010>; | |||||
mtd-mac-address-increment = <1>; | |||||
}; | |||||
&pinctrl { | |||||
state_default: pinctrl0 { | |||||
gpio { | |||||
ralink,group = "uart2", "wdt"; | |||||
ralink,function = "gpio"; | |||||
}; | |||||
}; | |||||
}; | |||||
&sdhci { | |||||
status = "okay"; | |||||
}; | |||||
&i2c { | |||||
status = "okay"; | |||||
}; | |||||
&pcie { | |||||
status = "okay"; | |||||
}; |