Changeset View
Changeset View
Standalone View
Standalone View
sys/arm/ralink/rt1310reg.h
- This file was added.
| /*- | |||||
| * Copyright (c) 2011 Jakub Wojciech Klama <jceel@FreeBSD.org> | |||||
| * Copyright (c) 2015 Hiroki Mori | |||||
| * All rights reserved. | |||||
| * | |||||
| * Redistribution and use in source and binary forms, with or without | |||||
| * modification, are permitted provided that the following conditions | |||||
| * are met: | |||||
| * 1. Redistributions of source code must retain the above copyright | |||||
| * notice, this list of conditions and the following disclaimer. | |||||
| * 2. Redistributions in binary form must reproduce the above copyright | |||||
| * notice, this list of conditions and the following disclaimer in the | |||||
| * documentation and/or other materials provided with the distribution. | |||||
| * | |||||
| * THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND | |||||
| * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE | |||||
| * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE | |||||
| * ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE | |||||
| * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL | |||||
| * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS | |||||
| * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) | |||||
| * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT | |||||
| * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY | |||||
| * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF | |||||
| * SUCH DAMAGE. | |||||
| * | |||||
| * $FreeBSD: head/sys/arm/lpc/lpcreg.h 260326 2014-01-05 18:40:06Z ian $ | |||||
mizhka: To be $FreeBSD$ | |||||
| */ | |||||
| #ifndef _ARM_RT_RTREG_H | |||||
| #define _ARM_RT_RTREG_H | |||||
mizhkaUnsubmitted Not Done Inline Actions_ARM_RALINK_RT1310REG_H? mizhka: _ARM_RALINK_RT1310REG_H? | |||||
| /* | |||||
| * Interrupt controller | |||||
| */ | |||||
| #define RT_INTC_SCR0 0x00 | |||||
| #define RT_INTC_SVR0 0x80 | |||||
| #define RT_INTC_ISR 0x104 | |||||
| #define RT_INTC_IPR 0x108 | |||||
| #define RT_INTC_IMR 0x10c | |||||
| #define RT_INTC_IECR 0x114 | |||||
| #define RT_INTC_ICCR 0x118 | |||||
| #define RT_INTC_TRIG_LOW_LVL (0) | |||||
| #define RT_INTC_TRIG_HIGH_LVL (1) | |||||
| #define RT_INTC_TRIG_NEG_EDGE (2) | |||||
| #define RT_INTC_TRIG_POS_EDGE (3) | |||||
| #define RT_INTC_TRIG_SHIF 6 | |||||
mizhkaUnsubmitted Not Done Inline ActionsTo be tabs after #define (at least it should be same style for all lines) mizhka: To be tabs after #define (at least it should be same style for all lines) | |||||
| /* | |||||
| * Timer 0|1|2|3. | |||||
| */ | |||||
| #define RT_TIMER_LOAD 0x00 | |||||
| #define RT_TIMER_VALUE 0x04 | |||||
| #define RT_TIMER_CONTROL 0x08 | |||||
| #define RT_TIMER_CTRL_INTCTL (1 << 1) | |||||
| #define RT_TIMER_CTRL_INTCLR (1 << 2) | |||||
| #define RT_TIMER_CTRL_INTMASK (1 << 3) | |||||
| #define RT_TIMER_CTRL_DIV16 (3 << 4) | |||||
| #define RT_TIMER_CTRL_DIV256 (7 << 4) | |||||
| #define RT_TIMER_CTRL_PERIODCAL (1 << 7) | |||||
| #define RT_TIMER_CTRL_ENABLE (1 << 8) | |||||
| #define RT_TIMER_INTERVAL (5000*150) | |||||
| /* | |||||
| * GPIO | |||||
| */ | |||||
| #define RT_GPIO_PORTA (0) | |||||
| #define RT_GPIO_PORTB (1) | |||||
| #define RT_GPIO_OFF_PADR (0x0) | |||||
| #define RT_GPIO_OFF_PADIR (0x4) | |||||
| #define RT_GPIO_OFF_PBDR (0x8) | |||||
| #define RT_GPIO_OFF_PBDIR (0xC) | |||||
| #endif /* _ARM_RT_RTREG_H */ | |||||
To be $FreeBSD$