Changeset View
Changeset View
Standalone View
Standalone View
sys/dev/mpr/mpr_sas_lsi.c
| Show First 20 Lines • Show All 751 Lines • ▼ Show 20 Lines | if (ret) { | ||||
| "(SSD or HDD) for SATA device with handle 0x%04x\n", | "(SSD or HDD) for SATA device with handle 0x%04x\n", | ||||
| __func__, handle); | __func__, handle); | ||||
| } else { | } else { | ||||
| mpr_dprint(sc, MPR_INFO, "SAS Address from SATA " | mpr_dprint(sc, MPR_INFO, "SAS Address from SATA " | ||||
| "device = %jx\n", sas_address); | "device = %jx\n", sas_address); | ||||
| } | } | ||||
| } | } | ||||
| /* | |||||
| * use_phynum: | |||||
| * 1 - use the PhyNum field as a fallback to the mapping logic | |||||
| * 0 - never use the PhyNum field | |||||
| * -1 - only use the PhyNum field | |||||
| */ | |||||
| id = MPR_MAP_BAD_ID; | |||||
| if (sc->use_phynum != -1) | |||||
| id = mpr_mapping_get_sas_id(sc, sas_address, handle); | id = mpr_mapping_get_sas_id(sc, sas_address, handle); | ||||
| if (id == MPR_MAP_BAD_ID) { | if (id == MPR_MAP_BAD_ID) { | ||||
| printf("failure at %s:%d/%s()! Could not get ID for device " | if ((sc->use_phynum == 0) | ||||
| "with handle 0x%04x\n", __FILE__, __LINE__, __func__, | || ((id = config_page.PhyNum) > sassc->maxtargets)) { | ||||
| handle); | mpr_dprint(sc, MPR_INFO, "failure at %s:%d/%s()! " | ||||
| "Could not get ID for device with handle 0x%04x\n", | |||||
| __FILE__, __LINE__, __func__, handle); | |||||
| error = ENXIO; | error = ENXIO; | ||||
| goto out; | goto out; | ||||
| } | } | ||||
| } | |||||
| if (mprsas_check_id(sassc, id) != 0) { | if (mprsas_check_id(sassc, id) != 0) { | ||||
| device_printf(sc->mpr_dev, "Excluding target id %d\n", id); | device_printf(sc->mpr_dev, "Excluding target id %d\n", id); | ||||
| error = ENXIO; | error = ENXIO; | ||||
| goto out; | goto out; | ||||
| } | } | ||||
| targ = &sassc->targets[id]; | |||||
| if (targ->handle != 0x0) { | |||||
| mpr_dprint(sc, MPR_MAPPING, "Attempting to reuse target id " | |||||
| "%d handle 0x%04x\n", id, targ->handle); | |||||
| error = ENXIO; | |||||
| goto out; | |||||
| } | |||||
| mpr_dprint(sc, MPR_MAPPING, "SAS Address from SAS device page0 = %jx\n", | mpr_dprint(sc, MPR_MAPPING, "SAS Address from SAS device page0 = %jx\n", | ||||
| sas_address); | sas_address); | ||||
| targ = &sassc->targets[id]; | |||||
| targ->devinfo = device_info; | targ->devinfo = device_info; | ||||
| targ->devname = le32toh(config_page.DeviceName.High); | targ->devname = le32toh(config_page.DeviceName.High); | ||||
| targ->devname = (targ->devname << 32) | | targ->devname = (targ->devname << 32) | | ||||
| le32toh(config_page.DeviceName.Low); | le32toh(config_page.DeviceName.Low); | ||||
| targ->encl_handle = le16toh(config_page.EnclosureHandle); | targ->encl_handle = le16toh(config_page.EnclosureHandle); | ||||
| targ->encl_slot = le16toh(config_page.Slot); | targ->encl_slot = le16toh(config_page.Slot); | ||||
| targ->encl_level = config_page.EnclosureLevel; | targ->encl_level = config_page.EnclosureLevel; | ||||
| targ->connector_name[0] = config_page.ConnectorName[0]; | targ->connector_name[0] = config_page.ConnectorName[0]; | ||||
| ▲ Show 20 Lines • Show All 624 Lines • Show Last 20 Lines | |||||