diff --git a/en_US.ISO8859-1/books/handbook/advanced-networking/chapter.sgml b/en_US.ISO8859-1/books/handbook/advanced-networking/chapter.sgml index 6088eade0c..3fb7614bfa 100644 --- a/en_US.ISO8859-1/books/handbook/advanced-networking/chapter.sgml +++ b/en_US.ISO8859-1/books/handbook/advanced-networking/chapter.sgml @@ -1,5640 +1,5640 @@ Advanced Networking Synopsis This chapter will cover a number of advanced networking topics. After reading this chapter, you will know: The basics of gateways and routes. How to set up IEEE 802.11 and &bluetooth; devices. How to make FreeBSD act as a bridge. How to set up network booting on a diskless machine. How to set up network address translation. How to connect two computers via PLIP. How to set up IPv6 on a FreeBSD machine. How to configure ATM. How to enable and utilize the features of CARP, the Common Access Redundancy Protocol in &os; Before reading this chapter, you should: Understand the basics of the /etc/rc scripts. Be familiar with basic network terminology. Know how to configure and install a new FreeBSD kernel (). Know how to install additional third-party software (). Coranth Gryphon Contributed by Gateways and Routes routing gateway subnet For one machine to be able to find another over a network, there must be a mechanism in place to describe how to get from one to the other. This is called routing. A route is a defined pair of addresses: a destination and a gateway. The pair indicates that if you are trying to get to this destination, communicate through this gateway. There are three types of destinations: individual hosts, subnets, and default. The default route is used if none of the other routes apply. We will talk a little bit more about default routes later on. There are also three types of gateways: individual hosts, interfaces (also called links), and Ethernet hardware addresses (MAC addresses). An Example To illustrate different aspects of routing, we will use the following example from netstat: &prompt.user; netstat -r Routing tables Destination Gateway Flags Refs Use Netif Expire default outside-gw UGSc 37 418 ppp0 localhost localhost UH 0 181 lo0 test0 0:e0:b5:36:cf:4f UHLW 5 63288 ed0 77 10.20.30.255 link#1 UHLW 1 2421 example.com link#1 UC 0 0 host1 0:e0:a8:37:8:1e UHLW 3 4601 lo0 host2 0:e0:a8:37:8:1e UHLW 0 5 lo0 => host2.example.com link#1 UC 0 0 224 link#1 UC 0 0 default route The first two lines specify the default route (which we will cover in the next section) and the localhost route. loopback device The interface (Netif column) that this routing table specifies to use for localhost is lo0, also known as the loopback device. This says to keep all traffic for this destination internal, rather than sending it out over the LAN, since it will only end up back where it started. Ethernet MAC address The next thing that stands out are the addresses beginning with 0:e0:. These are Ethernet hardware addresses, which are also known as MAC addresses. FreeBSD will automatically identify any hosts (test0 in the example) on the local Ethernet and add a route for that host, directly to it over the Ethernet interface, ed0. There is also a timeout (Expire column) associated with this type of route, which is used if we fail to hear from the host in a specific amount of time. When this happens, the route to this host will be automatically deleted. These hosts are identified using a mechanism known as RIP (Routing Information Protocol), which figures out routes to local hosts based upon a shortest path determination. subnet FreeBSD will also add subnet routes for the local subnet (10.20.30.255 is the broadcast address for the subnet 10.20.30, and example.com is the domain name associated with that subnet). The designation link#1 refers to the first Ethernet card in the machine. You will notice no additional interface is specified for those. Both of these groups (local network hosts and local subnets) have their routes automatically configured by a daemon called routed. If this is not run, then only routes which are statically defined (i.e. entered explicitly) will exist. The host1 line refers to our host, which it knows by Ethernet address. Since we are the sending host, FreeBSD knows to use the loopback interface (lo0) rather than sending it out over the Ethernet interface. The two host2 lines are an example of what happens when we use an &man.ifconfig.8; alias (see the section on Ethernet for reasons why we would do this). The => symbol after the lo0 interface says that not only are we using the loopback (since this address also refers to the local host), but specifically it is an alias. Such routes only show up on the host that supports the alias; all other hosts on the local network will simply have a link#1 line for such routes. The final line (destination subnet 224) deals with multicasting, which will be covered in another section. Finally, various attributes of each route can be seen in the Flags column. Below is a short table of some of these flags and their meanings: U Up: The route is active. H Host: The route destination is a single host. G Gateway: Send anything for this destination on to this remote system, which will figure out from there where to send it. S Static: This route was configured manually, not automatically generated by the system. C Clone: Generates a new route based upon this route for machines we connect to. This type of route is normally used for local networks. W WasCloned: Indicated a route that was auto-configured based upon a local area network (Clone) route. L Link: Route involves references to Ethernet hardware. Default Routes default route When the local system needs to make a connection to a remote host, it checks the routing table to determine if a known path exists. If the remote host falls into a subnet that we know how to reach (Cloned routes), then the system checks to see if it can connect along that interface. If all known paths fail, the system has one last option: the default route. This route is a special type of gateway route (usually the only one present in the system), and is always marked with a c in the flags field. For hosts on a local area network, this gateway is set to whatever machine has a direct connection to the outside world (whether via PPP link, DSL, cable modem, T1, or another network interface). If you are configuring the default route for a machine which itself is functioning as the gateway to the outside world, then the default route will be the gateway machine at your Internet Service Provider's (ISP) site. Let us look at an example of default routes. This is a common configuration: [Local2] <--ether--> [Local1] <--PPP--> [ISP-Serv] <--ether--> [T1-GW] The hosts Local1 and Local2 are at your site. Local1 is connected to an ISP via a dial up PPP connection. This PPP server computer is connected through a local area network to another gateway computer through an external interface to the ISPs Internet feed. The default routes for each of your machines will be: Host Default Gateway Interface Local2 Local1 Ethernet Local1 T1-GW PPP A common question is Why (or how) would we set the T1-GW to be the default gateway for Local1, rather than the ISP server it is connected to?. Remember, since the PPP interface is using an address on the ISP's local network for your side of the connection, routes for any other machines on the ISP's local network will be automatically generated. Hence, you will already know how to reach the T1-GW machine, so there is no need for the intermediate step of sending traffic to the ISP server. It is common to use the address X.X.X.1 as the gateway address for your local network. So (using the same example), if your local class-C address space was 10.20.30 and your ISP was using 10.9.9 then the default routes would be: Host Default Route Local2 (10.20.30.2) Local1 (10.20.30.1) Local1 (10.20.30.1, 10.9.9.30) T1-GW (10.9.9.1) You can easily define the default route via the /etc/rc.conf file. In our example, on the Local2 machine, we added the following line in /etc/rc.conf: defaultrouter="10.20.30.1" It is also possible to do it directly from the command line with the &man.route.8; command: &prompt.root; route add default 10.20.30.1 For more information on manual manipulation of network routing tables, consult &man.route.8; manual page. Dual Homed Hosts dual homed hosts There is one other type of configuration that we should cover, and that is a host that sits on two different networks. Technically, any machine functioning as a gateway (in the example above, using a PPP connection) counts as a dual-homed host. But the term is really only used to refer to a machine that sits on two local-area networks. In one case, the machine has two Ethernet cards, each having an address on the separate subnets. Alternately, the machine may only have one Ethernet card, and be using &man.ifconfig.8; aliasing. The former is used if two physically separate Ethernet networks are in use, the latter if there is one physical network segment, but two logically separate subnets. Either way, routing tables are set up so that each subnet knows that this machine is the defined gateway (inbound route) to the other subnet. This configuration, with the machine acting as a router between the two subnets, is often used when we need to implement packet filtering or firewall security in either or both directions. If you want this machine to actually forward packets between the two interfaces, you need to tell FreeBSD to enable this ability. See the next section for more details on how to do this. Building a Router router A network router is simply a system that forwards packets from one interface to another. Internet standards and good engineering practice prevent the FreeBSD Project from enabling this by default in FreeBSD. You can enable this feature by changing the following variable to YES in &man.rc.conf.5;: gateway_enable=YES # Set to YES if this host will be a gateway This option will set the &man.sysctl.8; variable net.inet.ip.forwarding to 1. If you should need to stop routing temporarily, you can reset this to 0 temporarily. Your new router will need routes to know where to send the traffic. If your network is simple enough you can use static routes. FreeBSD also comes with the standard BSD routing daemon &man.routed.8;, which speaks RIP (both version 1 and version 2) and IRDP. Support for BGP v4, OSPF v2, and other sophisticated routing protocols is available with the net/zebra package. Commercial products such as &gated; are also available for more complex network routing solutions. BGP RIP OSPF Al Hoang Contributed by Setting Up Static Routes Manual Configuration Let us assume we have a network as follows: INTERNET | (10.0.0.1/24) Default Router to Internet | |Interface xl0 |10.0.0.10/24 +------+ | | RouterA | | (FreeBSD gateway) +------+ | Interface xl1 | 192.168.1.1/24 | +--------------------------------+ Internal Net 1 | 192.168.1.2/24 | +------+ | | RouterB | | +------+ | 192.168.2.1/24 | Internal Net 2 In this scenario, RouterA is our &os; machine that is acting as a router to the rest of the Internet. It has a default route set to 10.0.0.1 which allows it to connect with the outside world. We will assume that RouterB is already configured properly and knows how to get wherever it needs to go. (This is simple in this picture. Just add a default route on RouterB using 192.168.1.1 as the gateway.) If we look at the routing table for RouterA we would see something like the following: &prompt.user; netstat -nr Routing tables Internet: Destination Gateway Flags Refs Use Netif Expire default 10.0.0.1 UGS 0 49378 xl0 127.0.0.1 127.0.0.1 UH 0 6 lo0 10.0.0/24 link#1 UC 0 0 xl0 192.168.1/24 link#2 UC 0 0 xl1 With the current routing table RouterA will not be able to reach our Internal Net 2. It does not have a route for 192.168.2.0/24. One way to alleviate this is to manually add the route. The following command would add the Internal Net 2 network to RouterA's routing table using 192.168.1.2 as the next hop: &prompt.root; route add -net 192.168.2.0/24 192.168.1.2 Now RouterA can reach any hosts on the 192.168.2.0/24 network. Persistent Configuration The above example is perfect for configuring a static route on a running system. However, one problem is that the routing information will not persist if you reboot your &os; machine. The way to handle the addition of a static route is to put it in your /etc/rc.conf file: # Add Internal Net 2 as a static route static_routes="internalnet2" route_internalnet2="-net 192.168.2.0/24 192.168.1.2" The static_routes configuration variable is a list of strings separated by a space. Each string references to a route name. In our above example we only have one string in static_routes. This string is internalnet2. We then add a configuration variable called route_internalnet2 where we put all of the configuration parameters we would give to the &man.route.8; command. For our example above we would have used the command: &prompt.root; route add -net 192.168.2.0/24 192.168.1.2 so we need "-net 192.168.2.0/24 192.168.1.2". As said above, we can have more than one string in static_routes. This allows us to create multiple static routes. The following lines shows an example of adding static routes for the 192.168.0.0/24 and 192.168.1.0/24 networks on an imaginary router: static_routes="net1 net2" route_net1="-net 192.168.0.0/24 192.168.0.1" route_net2="-net 192.168.1.0/24 192.168.1.1" Routing Propagation routing propagation We have already talked about how we define our routes to the outside world, but not about how the outside world finds us. We already know that routing tables can be set up so that all traffic for a particular address space (in our examples, a class-C subnet) can be sent to a particular host on that network, which will forward the packets inbound. When you get an address space assigned to your site, your service provider will set up their routing tables so that all traffic for your subnet will be sent down your PPP link to your site. But how do sites across the country know to send to your ISP? There is a system (much like the distributed DNS information) that keeps track of all assigned address-spaces, and defines their point of connection to the Internet Backbone. The Backbone are the main trunk lines that carry Internet traffic across the country, and around the world. Each backbone machine has a copy of a master set of tables, which direct traffic for a particular network to a specific backbone carrier, and from there down the chain of service providers until it reaches your network. It is the task of your service provider to advertise to the backbone sites that they are the point of connection (and thus the path inward) for your site. This is known as route propagation. Troubleshooting traceroute Sometimes, there is a problem with routing propagation, and some sites are unable to connect to you. Perhaps the most useful command for trying to figure out where routing is breaking down is the &man.traceroute.8; command. It is equally useful if you cannot seem to make a connection to a remote machine (i.e. &man.ping.8; fails). The &man.traceroute.8; command is run with the name of the remote host you are trying to connect to. It will show the gateway hosts along the path of the attempt, eventually either reaching the target host, or terminating because of a lack of connection. For more information, see the manual page for &man.traceroute.8;. Multicast Routing multicast routing kernel options MROUTING FreeBSD supports both multicast applications and multicast routing natively. Multicast applications do not require any special configuration of FreeBSD; applications will generally run out of the box. Multicast routing requires that support be compiled into the kernel: options MROUTING In addition, the multicast routing daemon, &man.mrouted.8; must be configured to set up tunnels and DVMRP via /etc/mrouted.conf. More details on multicast configuration may be found in the manual page for &man.mrouted.8;. As of &os; 7.0 the &man.mrouted.8; multicast routing daemon has been removed from the base system. It implements the DVMRP multicast routing protocol, which has largely been replaced by &man.pim.4; in many multicast installations. The related &man.map-mbone.8; and &man.mrinfo.8; utilities have also been removed. These programs are now available in the &os; Ports Collection as net/mrouted. Loader Marc Fonvieille Murray Stokely Wireless Networking wireless networking 802.11 wireless networking Wireless Networking Basics Most wireless networks are based on the IEEE 802.11 standards. A basic wireless network consists of multiple stations communicating with radios that broadcast in either the 2.4GHz or 5GHz band (though this varies according to the locale and is also changing to enable communication in the 2.3GHz and 4.9GHz ranges). 802.11 networks are organized in two ways: in infrastructure mode one station acts as a master with all the other stations associating to it; the network is known as a BSS and the master station is termed an access point (AP). In a BSS all communication passes through the AP; even when one station wants to communicate with another wireless station messages must go through the AP. In the second form of network there is no master and stations communicate directly. This form of network is termed an IBSS and is commonly known as an ad-hoc network. 802.11 networks were first deployed in the 2.4GHz band using protocols defined by the IEEE 802.11 and 802.11b standard. These specifications include the operating frequencies, MAC layer characteristics including framing and transmission rates (communication can be done at various rates). Later the 802.11a standard defined operation in the 5GHz band, including different signalling mechanisms and higher transmission rates. Still later the 802.11g standard was defined to enable use of 802.11a signalling and transmission mechanisms in the 2.4GHz band in such a way as to be backwards compatible with 802.11b networks. Separate from the underlying transmission techniques 802.11 networks have a variety of security mechanisms. The original 802.11 specifications defined a simple security protocol called WEP. This protocol uses a fixed pre-shared key and the RC4 cryptographic cipher to encode data transmitted on a network. Stations must all agree on the fixed key in order to communicate. This scheme was shown to be easily broken and is now rarely used except to discourage transient users from joining networks. Current security practice is given by the IEEE 802.11i specification that defines new cryptographic ciphers and an additional protocol to authenticate stations to an access point and exchange keys for doing data communication. Further, cryptographic keys are periodically refreshed and there are mechanisms for detecting intrusion attempts (and for countering intrusion attempts). Another security protocol specification commonly used in wireless networks is termed WPA. This was a precursor to 802.11i defined by an industry group as an interim measure while waiting for 802.11i to be ratified. WPA specifies a subset of the requirements found in 802.11i and is designed for implementation on legacy hardware. Specifically WPA requires only the TKIP cipher that is derived from the original WEP cipher. 802.11i permits use of TKIP but also requires support for a stronger cipher, AES-CCM, for encrypting data. (The AES cipher was not required in WPA because it was deemed too computationally costly to be implemented on legacy hardware.) Other than the above protocol standards the other important standard to be aware of is 802.11e. This defines protocols for deploying multi-media applications such as streaming video and voice over IP (VoIP) in an 802.11 network. Like 802.11i, 802.11e also has a precursor specification termed WME (later renamed WMM) that has been defined by an industry group as a subset of 802.11e that can be deployed now to enable multi-media applications while waiting for the final ratification of 802.11e. The most important thing to know about 802.11e and WME/WMM is that it enables prioritized traffic use of a wireless network through Quality of Service (QoS) protocols and enhanced media access protocols. Proper implementation of these protocols enable high speed bursting of data and prioritized traffic flow. Since the 6.0 version, &os; supports networks that operate using 802.11a, 802.11b, and 802.11g. The WPA and 802.11i security protocols are likewise supported (in conjunction with any of 11a, 11b, and 11g) and QoS and traffic prioritization required by the WME/WMM protocols are supported for a limited set of wireless devices. Basic Setup Kernel Configuration To use wireless networking you need a wireless networking card and to configure the kernel with the appropriate wireless networking support. The latter is separated into multiple modules so that you only need to configure the software you are actually going to use. The first thing you need is a wireless device. The most commonly used devices are those that use parts made by Atheros. These devices are supported by the &man.ath.4; driver and require the following line to be added to the /boot/loader.conf file: if_ath_load="YES" The Atheros driver is split up into three separate pieces: the driver proper (&man.ath.4;), the hardware support layer that handles chip-specific functions (&man.ath.hal.4;), and an algorithm for selecting which of several possible rates for transmitting frames (ath_rate_sample here). When you load this support as modules these dependencies are automatically handled for you. If instead of an Atheros device you had another device you would select the module for that device; e.g.: if_wi_load="YES" for devices based on the Intersil Prism parts (&man.wi.4; driver). In the rest of this document, we will use an &man.ath.4; device, the device name in the examples must be changed according to your configuration. A list of available wireless drivers can be found at the beginning of the &man.wlan.4; manual page. If a native &os; driver for your wireless device does not exist, it may be possible to directly use the &windows; driver with the help of the NDIS driver wrapper. With a device driver configured you need to also bring in the 802.11 networking support required by the driver. For the &man.ath.4; driver these are at least the &man.wlan.4;, wlan_scan_ap and wlan_scan_sta modules; the &man.wlan.4; module is automatically loaded with the wireless device driver, the remaining modules must be loaded at boot time via the /boot/loader.conf file: wlan_scan_ap_load="YES" wlan_scan_sta_load="YES" With that you will need the modules that implement cryptographic support for the security protocols you intend to use. These are intended to be dynamically loaded on demand by the &man.wlan.4; module but for now they must be manually configured. The following modules are available: &man.wlan.wep.4;, &man.wlan.ccmp.4; and &man.wlan.tkip.4;. Both &man.wlan.ccmp.4; and &man.wlan.tkip.4; drivers are only needed if you intend to use the WPA and/or 802.11i security protocols. If your network is to run totally open (i.e., with no encryption) then you do not even need the &man.wlan.wep.4; support. To load these modules at boot time, add the following lines to /boot/loader.conf: wlan_wep_load="YES" wlan_ccmp_load="YES" wlan_tkip_load="YES" With this information in the system bootstrap configuration file (i.e., /boot/loader.conf), you have to reboot your &os; box. If you do not want to reboot your machine for the moment, you can just load the modules by hand using &man.kldload.8;. If you do not want to use modules, it is possible to compile these drivers into the kernel by adding the following lines to your kernel configuration file: device ath # Atheros IEEE 802.11 wireless network driver device ath_hal # Atheros Hardware Access Layer device ath_rate_sample # John Bicket's SampleRate control algorithm. device wlan # 802.11 support (Required) device wlan_scan_ap # 802.11 AP mode scanning device wlan_scan_sta # 802.11 STA mode scanning device wlan_wep # WEP crypto support for 802.11 devices device wlan_ccmp # AES-CCMP crypto support for 802.11 devices device wlan_tkip # TKIP and Michael crypto support for 802.11 devices With this information in the kernel configuration file, recompile the kernel and reboot your &os; machine. When the system is up, we could find some information about the wireless device in the boot messages, like this: ath0: <Atheros 5212> mem 0xff9f0000-0xff9fffff irq 17 at device 2.0 on pci2 ath0: Ethernet address: 00:11:95:d5:43:62 ath0: mac 7.9 phy 4.5 radio 5.6 Infrastructure Mode The infrastructure mode or BSS mode is the mode that is typically used. In this mode, a number of wireless access points are connected to a wired network. Each wireless network has its own name, this name is called the SSID of the network. Wireless clients connect to the wireless access points. &os; Clients How to Find Access Points To scan for networks, use the ifconfig command. This request may take a few moments to complete as it requires that the system switches to each available wireless frequency and probes for available access points. Only the super-user can initiate such a scan: &prompt.root; ifconfig ath0 up scan SSID BSSID CHAN RATE S:N INT CAPS dlinkap 00:13:46:49:41:76 6 54M 29:3 100 EPS WPA WME freebsdap 00:11:95:c3:0d:ac 1 54M 22:1 100 EPS WPA You must mark the interface before you can scan. Subsequent scan requests do not require you to mark the interface up again. The output of a scan request lists each BSS/IBSS network found. Beside the name of the network, SSID, we find the BSSID which is the MAC address of the access point. The CAPS field identifies the type of each network and the capabilities of the stations operating there: E Extended Service Set (ESS). Indicates that the station is part of an infrastructure network (in contrast to an IBSS/ad-hoc network). I IBSS/ad-hoc network. Indicates that the station is part of an ad-hoc network (in contrast to an ESS network). P Privacy. Data confidentiality is required for all data frames exchanged within the BSS. This means that this BSS requires the station to use cryptographic means such as WEP, TKIP or AES-CCMP to encrypt/decrypt data frames being exchanged with others. S Short Preamble. Indicates that the network is using short preambles (defined in 802.11b High Rate/DSSS PHY, short preamble utilizes a 56 bit sync field in contrast to a 128 bit field used in long preamble mode). s Short slot time. Indicates that the 802.11g network is using a short slot time because there are no legacy (802.11b) stations present. One can also display the current list of known networks with: &prompt.root; ifconfig ath0 list scan This information may be updated automatically by the adapter or manually with a request. Old data is automatically removed from the cache, so over time this list may shrink unless more scans are done. Basic Settings This section provides a simple example of how to make the wireless network adapter work in &os; without encryption. After you are familiar with these concepts, we strongly recommend using WPA to set up your wireless network. There are three basic steps to configure a wireless network: selecting an access point, authenticating your station, and configuring an IP address. The following sections discuss each step. Selecting an Access Point Most of time it is sufficient to let the system choose an access point using the builtin heuristics. This is the default behaviour when you mark an interface up or otherwise configure an interface by listing it in /etc/rc.conf, e.g.: ifconfig_ath0="DHCP" If there are multiple access points and you want to select a specific one, you can select it by its SSID: ifconfig_ath0="ssid your_ssid_here DHCP" In an environment where there are multiple access points with the same SSID (often done to simplify roaming) it may be necessary to associate to one specific device. In this case you can also specify the BSSID of the access point (you can also leave off the SSID): ifconfig_ath0="ssid your_ssid_here bssid xx:xx:xx:xx:xx:xx DHCP" There are other ways to constrain the choice of an access point such as limiting the set of frequencies the system will scan on. This may be useful if you have a multi-band wireless card as scanning all the possible channels can be time-consuming. To limit operation to a specific band you can use the parameter; e.g.: ifconfig_ath0="mode 11g ssid your_ssid_here DHCP" will force the card to operate in 802.11g which is defined only for 2.4GHz frequencies so any 5GHz channels will not be considered. Other ways to do this are the parameter, to lock operation to one specific frequency, and the parameter, to specify a list of channels for scanning. More information about these parameters can be found in the &man.ifconfig.8; manual page. Authentication Once you have selected an access point your station needs to authenticate before it can pass data. Authentication can happen in several ways. The most common scheme used is termed open authentication and allows any station to join the network and communicate. This is the authentication you should use for test purpose the first time you set up a wireless network. Other schemes require cryptographic handshakes be completed before data traffic can flow; either using pre-shared keys or secrets, or more complex schemes that involve backend services such as RADIUS. Most users will use open authentication which is the default setting. Next most common setup is WPA-PSK, also known as WPA Personal, which is described below. If you have an &apple; &airport; Extreme base station for an access point you may need to configure shared-key authentication together with a WEP key. This can be done in the /etc/rc.conf file or using the &man.wpa.supplicant.8; program. If you have a single &airport; base station you can setup access with something like: ifconfig_ath0="authmode shared wepmode on weptxkey 1 wepkey 01234567 DHCP" In general shared key authentication is to be avoided because it uses the WEP key material in a highly-constrained manner making it even easier to crack the key. If WEP must be used (e.g., for compatibility with legacy devices) it is better to use WEP with open authentication. More information regarding WEP can be found in the . Getting an IP Address with DHCP Once you have selected an access point and set the authentication parameters, you will have to get an IP address to communicate. Most of time you will obtain your wireless IP address via DHCP. To achieve that, simply edit /etc/rc.conf and add DHCP to the configuration for your device as shown in various examples above: ifconfig_ath0="DHCP" At this point, you are ready to bring up the wireless interface: &prompt.root; /etc/rc.d/netif start Once the interface is running, use ifconfig to see the status of the interface ath0: &prompt.root; ifconfig ath0 ath0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500 inet6 fe80::211:95ff:fed5:4362%ath0 prefixlen 64 scopeid 0x1 inet 192.168.1.100 netmask 0xffffff00 broadcast 192.168.1.255 ether 00:11:95:d5:43:62 media: IEEE 802.11 Wireless Ethernet autoselect (OFDM/54Mbps) status: associated ssid dlinkap channel 6 bssid 00:13:46:49:41:76 authmode OPEN privacy OFF txpowmax 36 protmode CTS bintval 100 The status: associated means you are connected to the wireless network (to the dlinkap network in our case). The bssid 00:13:46:49:41:76 part is the MAC address of your access point; the authmode line informs you that the communication is not encrypted (OPEN). Static IP Address In the case you cannot obtain an IP address from a DHCP server, you can set a fixed IP address. Replace the DHCP keyword shown above with the address information. Be sure to retain any other parameters you have set up for selecting an access point: ifconfig_ath0="ssid your_ssid_here inet 192.168.1.100 netmask 255.255.255.0" WPA WPA (Wi-Fi Protected Access) is a security protocol used together with 802.11 networks to address the lack of proper authentication and the weakness of WEP. WPA leverages the 802.1X authentication protocol and uses one of several ciphers instead of WEP for data integrity. The only cipher required by WPA is TKIP (Temporary Key Integrity Protocol) which is a cipher that extends the basic RC4 cipher used by WEP by adding integrity checking, tamper detection, and measures for responding to any detected intrusions. TKIP is designed to work on legacy hardware with only software modification; it represents a compromise that improves security but is still not entirely immune to attack. WPA also specifies the AES-CCMP cipher as an alternative to TKIP and that is preferred when possible; for this specification the term WPA2 (or RSN) is commonly used. WPA defines authentication and encryption protocols. Authentication is most commonly done using one of two techniques: by 802.1X and a backend authentication service such as RADIUS, or by a minimal handshake between the station and the access point using a pre-shared secret. The former is commonly termed WPA Enterprise with the latter known as WPA Personal. Since most people will not set up a RADIUS backend server for wireless network, WPA-PSK is by far the most commonly encountered configuration for WPA. The control of the wireless connection and the authentication (key negotiation or authentication with a server) is done with the &man.wpa.supplicant.8; utility. This program requires a configuration file, /etc/wpa_supplicant.conf, to run. More information regarding this file can be found in the &man.wpa.supplicant.conf.5; manual page. WPA-PSK WPA-PSK also known as WPA-Personal is based on a pre-shared key (PSK) generated from a given password and that will be used as the master key in the wireless network. This means every wireless user will share the same key. WPA-PSK is intended for small networks where the use of an authentication server is not possible or desired. Always use strong passwords that are sufficiently long and made from a rich alphabet so they will not be guessed and/or attacked. The first step is the configuration of the /etc/wpa_supplicant.conf file with the SSID and the pre-shared key of your network: network={ ssid="freebsdap" psk="freebsdmall" } Then, in /etc/rc.conf, we indicate that the wireless device configuration will be done with WPA and the IP address will be obtained with DHCP: ifconfig_ath0="WPA DHCP" Then, we can bring up the interface: &prompt.root; /etc/rc.d/netif start Starting wpa_supplicant. DHCPDISCOVER on ath0 to 255.255.255.255 port 67 interval 5 DHCPDISCOVER on ath0 to 255.255.255.255 port 67 interval 6 DHCPOFFER from 192.168.0.1 DHCPREQUEST on ath0 to 255.255.255.255 port 67 DHCPACK from 192.168.0.1 bound to 192.168.0.254 -- renewal in 300 seconds. ath0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500 inet6 fe80::211:95ff:fed5:4362%ath0 prefixlen 64 scopeid 0x1 inet 192.168.0.254 netmask 0xffffff00 broadcast 192.168.0.255 ether 00:11:95:d5:43:62 media: IEEE 802.11 Wireless Ethernet autoselect (OFDM/36Mbps) status: associated ssid freebsdap channel 1 bssid 00:11:95:c3:0d:ac authmode WPA privacy ON deftxkey UNDEF TKIP 2:128-bit txpowmax 36 protmode CTS roaming MANUAL bintval 100 Or you can try to configure it manually using the same /etc/wpa_supplicant.conf above, and run: &prompt.root; wpa_supplicant -i ath0 -c /etc/wpa_supplicant.conf Trying to associate with 00:11:95:c3:0d:ac (SSID='freebsdap' freq=2412 MHz) Associated with 00:11:95:c3:0d:ac WPA: Key negotiation completed with 00:11:95:c3:0d:ac [PTK=TKIP GTK=TKIP] The next operation is the launch of the dhclient command to get the IP address from the DHCP server: &prompt.root; dhclient ath0 DHCPREQUEST on ath0 to 255.255.255.255 port 67 DHCPACK from 192.168.0.1 bound to 192.168.0.254 -- renewal in 300 seconds. &prompt.root; ifconfig ath0 ath0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500 inet6 fe80::211:95ff:fed5:4362%ath0 prefixlen 64 scopeid 0x1 inet 192.168.0.254 netmask 0xffffff00 broadcast 192.168.0.255 ether 00:11:95:d5:43:62 media: IEEE 802.11 Wireless Ethernet autoselect (OFDM/48Mbps) status: associated ssid freebsdap channel 1 bssid 00:11:95:c3:0d:ac authmode WPA privacy ON deftxkey UNDEF TKIP 2:128-bit txpowmax 36 protmode CTS roaming MANUAL bintval 100 If the /etc/rc.conf is set up with the line ifconfig_ath0="DHCP" then it is no need to run the dhclient command manually, dhclient will be launched after wpa_supplicant plumbs the keys. In the case where the use of DHCP is not possible, you can set a static IP address after wpa_supplicant has authenticated the station: &prompt.root; ifconfig ath0 inet 192.168.0.100 netmask 255.255.255.0 &prompt.root; ifconfig ath0 ath0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500 inet6 fe80::211:95ff:fed5:4362%ath0 prefixlen 64 scopeid 0x1 inet 192.168.0.100 netmask 0xffffff00 broadcast 192.168.0.255 ether 00:11:95:d5:43:62 media: IEEE 802.11 Wireless Ethernet autoselect (OFDM/36Mbps) status: associated ssid freebsdap channel 1 bssid 00:11:95:c3:0d:ac authmode WPA privacy ON deftxkey UNDEF TKIP 2:128-bit txpowmax 36 protmode CTS roaming MANUAL bintval 100 When DHCP is not used, you also have to manually set up the default gateway and the nameserver: &prompt.root; route add default your_default_router &prompt.root; echo "nameserver your_DNS_server" >> /etc/resolv.conf WPA with EAP-TLS The second way to use WPA is with an 802.1X backend authentication server, in this case WPA is called WPA-Enterprise to make difference with the less secure WPA-Personal with its pre-shared key. The authentication in WPA-Enterprise is based on EAP (Extensible Authentication Protocol). EAP does not come with an encryption method, it was decided to embed EAP inside an encrypted tunnel. Many types of EAP authentication methods have been designed, the most common methods are EAP-TLS, EAP-TTLS and EAP-PEAP. EAP-TLS (EAP with Transport Layer Security) is a very well-supported authentication protocol in the wireless world since it was the first EAP method to be certified by the Wi-Fi alliance. EAP-TLS will require three certificates to run: the CA certificate (installed on all machines), the server certificate for your authentication server, and one client certificate for each wireless client. In this EAP method, both authentication server and wireless client authenticate each other in presenting their respective certificates, and they verify that these certificates were signed by your organization's certificate authority (CA). As previously, the configuration is done via /etc/wpa_supplicant.conf: network={ ssid="freebsdap" proto=RSN key_mgmt=WPA-EAP eap=TLS identity="loader" ca_cert="/etc/certs/cacert.pem" client_cert="/etc/certs/clientcert.pem" private_key="/etc/certs/clientkey.pem" private_key_passwd="freebsdmallclient" } This field indicates the network name (SSID). Here, we use RSN (IEEE 802.11i) protocol, i.e., WPA2. The key_mgmt line refers to the key management protocol we use. In our case it is WPA using EAP authentication: WPA-EAP. In this field, we mention the EAP method for our connection. The identity field contains the identity string for EAP. The ca_cert field indicates the pathname of the CA certificate file. This file is needed to verify the server certificat. The client_cert line gives the pathname to the client certificate file. This certificate is unique to each wireless client of the network. The private_key field is the pathname to the client certificate private key file. The private_key_passwd field contains the passphrase for the private key. Then add the following line to /etc/rc.conf: ifconfig_ath0="WPA DHCP" The next step is to bring up the interface with the help of the rc.d facility: &prompt.root; /etc/rc.d/netif start Starting wpa_supplicant. DHCPREQUEST on ath0 to 255.255.255.255 port 67 DHCPREQUEST on ath0 to 255.255.255.255 port 67 DHCPACK from 192.168.0.20 bound to 192.168.0.254 -- renewal in 300 seconds. ath0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500 inet6 fe80::211:95ff:fed5:4362%ath0 prefixlen 64 scopeid 0x1 inet 192.168.0.254 netmask 0xffffff00 broadcast 192.168.0.255 ether 00:11:95:d5:43:62 media: IEEE 802.11 Wireless Ethernet autoselect (DS/11Mbps) status: associated ssid freebsdap channel 1 bssid 00:11:95:c3:0d:ac authmode WPA2/802.11i privacy ON deftxkey UNDEF TKIP 2:128-bit txpowmax 36 protmode CTS roaming MANUAL bintval 100 As previously shown, it is also possible to bring up the interface manually with both wpa_supplicant and ifconfig commands. WPA with EAP-TTLS With EAP-TLS both the authentication server and the client need a certificate, with EAP-TTLS (EAP-Tunneled Transport Layer Security) a client certificate is optional. This method is close to what some secure web sites do , where the web server can create a secure SSL tunnel even if the visitors do not have client-side certificates. EAP-TTLS will use the encrypted TLS tunnel for safe transport of the authentication data. The configuration is done via the /etc/wpa_supplicant.conf file: network={ ssid="freebsdap" proto=RSN key_mgmt=WPA-EAP eap=TTLS identity="test" password="test" ca_cert="/etc/certs/cacert.pem" phase2="auth=MD5" } In this field, we mention the EAP method for our connection. The identity field contains the identity string for EAP authentication inside the encrypted TLS tunnel. The password field contains the passphrase for the EAP authentication. The ca_cert field indicates the pathname of the CA certificate file. This file is needed to verify the server certificat. In this field, we mention the authentication method used in the encrypted TLS tunnel. In our case, EAP with MD5-Challenge has been used. The inner authentication phase is often called phase2. You also have to add the following line to /etc/rc.conf: ifconfig_ath0="WPA DHCP" The next step is to bring up the interface: &prompt.root; /etc/rc.d/netif start Starting wpa_supplicant. DHCPREQUEST on ath0 to 255.255.255.255 port 67 DHCPREQUEST on ath0 to 255.255.255.255 port 67 DHCPREQUEST on ath0 to 255.255.255.255 port 67 DHCPACK from 192.168.0.20 bound to 192.168.0.254 -- renewal in 300 seconds. ath0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500 inet6 fe80::211:95ff:fed5:4362%ath0 prefixlen 64 scopeid 0x1 inet 192.168.0.254 netmask 0xffffff00 broadcast 192.168.0.255 ether 00:11:95:d5:43:62 media: IEEE 802.11 Wireless Ethernet autoselect (DS/11Mbps) status: associated ssid freebsdap channel 1 bssid 00:11:95:c3:0d:ac authmode WPA2/802.11i privacy ON deftxkey UNDEF TKIP 2:128-bit txpowmax 36 protmode CTS roaming MANUAL bintval 100 WPA with EAP-PEAP PEAP (Protected EAP) has been designed as an alternative to EAP-TTLS. There are two types of PEAP methods, the most common one is PEAPv0/EAP-MSCHAPv2. In the rest of this document, we will use the PEAP term to refer to that EAP method. PEAP is the most used EAP standard after EAP-TLS, in other words if you have a network with mixed OSes, PEAP should be the most supported standard after EAP-TLS. PEAP is similar to EAP-TTLS: it uses a server-side certificate to authenticate clients by creating an encrypted TLS tunnel between the client and the authentication server, which protects the ensuing exchange of authentication information. In term of security the difference between EAP-TTLS and PEAP is that PEAP authentication broadcasts the username in clear, only the password is sent in the encrypted TLS tunnel. EAP-TTLS will use the TLS tunnel for both username and password. We have to edit the /etc/wpa_supplicant.conf file and add the EAP-PEAP related settings: network={ ssid="freebsdap" proto=RSN key_mgmt=WPA-EAP eap=PEAP identity="test" password="test" ca_cert="/etc/certs/cacert.pem" phase1="peaplabel=0" phase2="auth=MSCHAPV2" } In this field, we mention the EAP method for our connection. The identity field contains the identity string for EAP authentication inside the encrypted TLS tunnel. The password field contains the passphrase for the EAP authentication. The ca_cert field indicates the pathname of the CA certificate file. This file is needed to verify the server certificat. This field contains the parameters for the first phase of the authentication (the TLS tunnel). According to the authentication server used, you will have to specify a specific label for the authentication. Most of time, the label will be client EAP encryption which is set by using peaplabel=0. More information can be found in the &man.wpa.supplicant.conf.5; manual page. In this field, we mention the authentication protocol used in the encrypted TLS tunnel. In the case of PEAP, it is auth=MSCHAPV2. The following must be added to /etc/rc.conf: ifconfig_ath0="WPA DHCP" Then, we can bring up the interface: &prompt.root; /etc/rc.d/netif start Starting wpa_supplicant. DHCPREQUEST on ath0 to 255.255.255.255 port 67 DHCPREQUEST on ath0 to 255.255.255.255 port 67 DHCPREQUEST on ath0 to 255.255.255.255 port 67 DHCPACK from 192.168.0.20 bound to 192.168.0.254 -- renewal in 300 seconds. ath0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500 inet6 fe80::211:95ff:fed5:4362%ath0 prefixlen 64 scopeid 0x1 inet 192.168.0.254 netmask 0xffffff00 broadcast 192.168.0.255 ether 00:11:95:d5:43:62 media: IEEE 802.11 Wireless Ethernet autoselect (DS/11Mbps) status: associated ssid freebsdap channel 1 bssid 00:11:95:c3:0d:ac authmode WPA2/802.11i privacy ON deftxkey UNDEF TKIP 2:128-bit txpowmax 36 protmode CTS roaming MANUAL bintval 100 WEP WEP (Wired Equivalent Privacy) is part of the original 802.11 standard. There is no authentication mechanism, only a weak form of access control, and it is easily to be cracked. WEP can be set up with ifconfig: &prompt.root; ifconfig ath0 ssid my_net wepmode on weptxkey 3 wepkey 3:0x3456789012 \ inet 192.168.1.100 netmask 255.255.255.0 The weptxkey means which WEP key will be used in the transmission. Here we used the third key. This must match the setting in the access point. If you do not have any idea of what is the key used by the access point, you should try to use 1 (i.e., the first key) for this value. The wepkey means setting the selected WEP key. It should in the format index:key, if the index is not given, key 1 is set. That is to say we need to set the index if we use keys other than the first key. You must replace the 0x3456789012 with the key configured for use on the access point. You are encouraged to read &man.ifconfig.8; manual page for further information. The wpa_supplicant facility also can be used to configure your wireless interface with WEP. The example above can be set up by adding the following lines to /etc/wpa_supplicant.conf: network={ ssid="my_net" key_mgmt=NONE wep_key3=3456789012 wep_tx_keyidx=3 } Then: &prompt.root; wpa_supplicant -i ath0 -c /etc/wpa_supplicant.conf Trying to associate with 00:13:46:49:41:76 (SSID='dlinkap' freq=2437 MHz) Associated with 00:13:46:49:41:76 Ad-hoc Mode IBSS mode, also called ad-hoc mode, is designed for point to point connections. For example, to establish an ad-hoc network between the machine A and the machine B we will just need to choose two IP adresses and a SSID. On the box A: &prompt.root; ifconfig ath0 ssid freebsdap mediaopt adhoc inet 192.168.0.1 netmask 255.255.255.0 &prompt.root; ifconfig ath0 ath0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500 inet 192.168.0.1 netmask 0xffffff00 broadcast 192.168.0.255 inet6 fe80::211:95ff:fec3:dac%ath0 prefixlen 64 scopeid 0x4 ether 00:11:95:c3:0d:ac media: IEEE 802.11 Wireless Ethernet autoselect <adhoc> (autoselect <adhoc>) status: associated ssid freebsdap channel 2 bssid 02:11:95:c3:0d:ac authmode OPEN privacy OFF txpowmax 36 protmode CTS bintval 100 The adhoc parameter indicates the interface is running in the IBSS mode. On B, we should be able to detect A: &prompt.root; ifconfig ath0 up scan SSID BSSID CHAN RATE S:N INT CAPS freebsdap 02:11:95:c3:0d:ac 2 54M 19:3 100 IS The I in the output confirms the machine A is in ad-hoc mode. We just have to configure B with a different IP address: &prompt.root; ifconfig ath0 ssid freebsdap mediaopt adhoc inet 192.168.0.2 netmask 255.255.255.0 &prompt.root; ifconfig ath0 ath0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500 inet6 fe80::211:95ff:fed5:4362%ath0 prefixlen 64 scopeid 0x1 inet 192.168.0.2 netmask 0xffffff00 broadcast 192.168.0.255 ether 00:11:95:d5:43:62 media: IEEE 802.11 Wireless Ethernet autoselect <adhoc> (autoselect <adhoc>) status: associated ssid freebsdap channel 2 bssid 02:11:95:c3:0d:ac authmode OPEN privacy OFF txpowmax 36 protmode CTS bintval 100 Both A and B are now ready to exchange informations. &os; Host Access Points &os; can act as an Access Point (AP) which eliminates the need to buy a hardware AP or run an ad-hoc network. This can be particularly useful when your &os; machine is acting as a gateway to another network (e.g., the Internet). Basic Settings Before configuring your &os; machine as an AP, the kernel must be configured with the appropriate wireless networking support for your wireless card. You also have to add the support for the security protocols you intend to use. For more details, see . The use of the NDIS driver wrapper and the &windows; drivers do not allow currently the AP operation. Only native &os; wireless drivers support AP mode. Once the wireless networking support is loaded, you can check if your wireless device supports the host-based access point mode (also know as hostap mode): &prompt.root; ifconfig ath0 list caps ath0=783ed0f<WEP,TKIP,AES,AES_CCM,IBSS,HOSTAP,AHDEMO,TXPMGT,SHSLOT,SHPREAMBLE,MONITOR,TKIPMIC,WPA1,WPA2,BURST,WME> This output displays the card capabilities; the HOSTAP word confirms this wireless card can act as an Access Point. Various supported ciphers are also mentioned: WEP, TKIP, WPA2, etc., these informations are important to know what security protocols could be set on the Access Point. The wireless device can now be put into hostap mode and configured with the correct SSID and IP address: &prompt.root; ifconfig ath0 ssid freebsdap mode 11g mediaopt hostap inet 192.168.0.1 netmask 255.255.255.0 Use again ifconfig to see the status of the ath0 interface: &prompt.root; ifconfig ath0 ath0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500 inet 192.168.0.1 netmask 0xffffff00 broadcast 192.168.0.255 inet6 fe80::211:95ff:fec3:dac%ath0 prefixlen 64 scopeid 0x4 ether 00:11:95:c3:0d:ac media: IEEE 802.11 Wireless Ethernet autoselect mode 11g <hostap> status: associated ssid freebsdap channel 1 bssid 00:11:95:c3:0d:ac authmode OPEN privacy OFF txpowmax 38 bmiss 7 protmode CTS burst dtimperiod 1 bintval 100 The hostap parameter indicates the interface is running in the host-based access point mode. The interface configuration can be done automatically at boot time by adding the following line to /etc/rc.conf: ifconfig_ath0="ssid freebsdap mode 11g mediaopt hostap inet 192.168.0.1 netmask 255.255.255.0" Host-based Access Point without Authentication or Encryption Although it is not recommended to run an AP without any authentication or encryption, this is a simple way to check if your AP is working. This configuration is also important for debugging client issues. Once the AP configured as previously shown, it is possible from another wireless machine to initiate a scan to find the AP: &prompt.root; ifconfig ath0 up scan SSID BSSID CHAN RATE S:N INT CAPS freebsdap 00:11:95:c3:0d:ac 1 54M 22:1 100 ES The client machine found the Access Point and can be associated with it: &prompt.root; ifconfig ath0 ssid freebsdap inet 192.168.0.2 netmask 255.255.255.0 &prompt.root; ifconfig ath0 ath0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500 inet6 fe80::211:95ff:fed5:4362%ath0 prefixlen 64 scopeid 0x1 inet 192.168.0.2 netmask 0xffffff00 broadcast 192.168.0.255 ether 00:11:95:d5:43:62 media: IEEE 802.11 Wireless Ethernet autoselect (OFDM/54Mbps) status: associated ssid freebsdap channel 1 bssid 00:11:95:c3:0d:ac authmode OPEN privacy OFF txpowmax 36 protmode CTS bintval 100 WPA Host-based Access Point This section will focus on setting up &os; Access Point using the WPA security protocol. More details regarding WPA and the configuration of WPA-based wireless clients can be found in the . The hostapd daemon is used to deal with client authentication and keys management on the WPA enabled Access Point. In the following, all the configuration operations will be performed on the &os; machine acting as AP. Once the AP is correctly working, hostapd should be automatically enabled at boot with the following line in /etc/rc.conf: hostapd_enable="YES" Before trying to configure hostapd, be sure you have done the basic settings introduced in the . WPA-PSK WPA-PSK is intended for small networks where the use of an backend authentication server is not possible or desired. The configuration is done in the /etc/hostapd.conf file: interface=ath0 debug=1 ctrl_interface=/var/run/hostapd ctrl_interface_group=wheel ssid=freebsdap wpa=1 wpa_passphrase=freebsdmall wpa_key_mgmt=WPA-PSK wpa_pairwise=CCMP TKIP This field indicates the wireless interface used for the Access Point. This field sets the level of verbosity during the execution of hostapd. A value of 1 represents the minimal level. The ctrl_interface field gives the pathname of the directory used by hostapd to stores its domain socket files for the communication with external programs such as &man.hostapd.cli.8;. The default value is used here. The ctrl_interface_group line sets the group (here, it is the wheel group) allowed to access to the control interface files. This field sets the network name. The wpa field enables WPA and specifies which WPA authentication protocol will be required. A value of 1 configures the AP for WPA-PSK. The wpa_passphrase field contains the ASCII passphrase for the WPA authentication. Always use strong passwords that are sufficiently long and made from a rich alphabet so they will not be guessed and/or attacked. The wpa_key_mgmt line refers to the key management protocol we use. In our case it is WPA-PSK. The wpa_pairwise field indicates the set of accepted encryption algorithms by the Access Point. Here both TKIP (WPA) and CCMP (WPA2) ciphers are accepted. CCMP cipher is an alternative to TKIP and that is strongly preferred when possible; TKIP should be used solely for stations incapable of doing CCMP. The next step is to start hostapd: &prompt.root /etc/rc.d/hostapd forcestart &prompt.root; ifconfig ath0 ath0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 2290 inet 192.168.0.1 netmask 0xffffff00 broadcast 192.168.0.255 inet6 fe80::211:95ff:fec3:dac%ath0 prefixlen 64 scopeid 0x4 ether 00:11:95:c3:0d:ac media: IEEE 802.11 Wireless Ethernet autoselect mode 11g <hostap> status: associated ssid freebsdap channel 1 bssid 00:11:95:c3:0d:ac authmode WPA2/802.11i privacy MIXED deftxkey 2 TKIP 2:128-bit txpowmax 36 protmode CTS dtimperiod 1 bintval 100 The Access Point is running, the clients can now be associated with it, see for more details. It is possible to see the stations associated with the AP using the ifconfig ath0 list sta command. WEP Host-based Access Point It is not recommended to use WEP for setting up an Access Point since there is no authentication mechanism and it is easily to be cracked. Some legacy wireless cards only support WEP as security protocol, these cards will only allow to set up AP without authentication or encryption or using the WEP protocol. The wireless device can now be put into hostap mode and configured with the correct SSID and IP address: &prompt.root; ifconfig ath0 ssid freebsdap wepmode on weptxkey 3 wepkey 3:0x3456789012 mode 11g mediaopt hostap \ inet 192.168.0.1 netmask 255.255.255.0 The weptxkey means which WEP key will be used in the transmission. Here we used the third key (note that the key numbering starts with 1). This parameter must be specified to really encrypt the data. The wepkey means setting the selected WEP key. It should in the format index:key, if the index is not given, key 1 is set. That is to say we need to set the index if we use keys other than the first key. Use again ifconfig to see the status of the ath0 interface: &prompt.root; ifconfig ath0 ath0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500 inet 192.168.0.1 netmask 0xffffff00 broadcast 192.168.0.255 inet6 fe80::211:95ff:fec3:dac%ath0 prefixlen 64 scopeid 0x4 ether 00:11:95:c3:0d:ac media: IEEE 802.11 Wireless Ethernet autoselect mode 11g <hostap> status: associated ssid freebsdap channel 1 bssid 00:11:95:c3:0d:ac authmode OPEN privacy ON deftxkey 3 wepkey 3:40-bit txpowmax 36 protmode CTS dtimperiod 1 bintval 100 From another wireless machine, it is possible to initiate a scan to find the AP: &prompt.root; ifconfig ath0 up scan SSID BSSID CHAN RATE S:N INT CAPS freebsdap 00:11:95:c3:0d:ac 1 54M 22:1 100 EPS The client machine found the Access Point and can be associated with it using the correct parameters (key, etc.), see for more details. Troubleshooting If you are having trouble with wireless networking, there are a number of steps you can take to help troubleshoot the problem. If you do not see the access point listed when scanning be sure you have not configured your wireless device to a limited set of channels. If you cannot associate to an access point verify the configuration of your station matches the one of the access point. This includes the authentication scheme and any security protocols. Simplify your configuration as much as possible. If you are using a security protocol such as WPA or WEP configure the access point for open authentication and no security to see if you can get traffic to pass. Once you can associate to the access point diagnose any security configuration using simple tools like &man.ping.8;. The wpa_supplicant has much debugging support; try running it manually with the option and look at the system logs. There are also many lower-level debugging tools. You can enable debugging messages in the 802.11 protocol support layer using the wlandebug program found in /usr/src/tools/tools/net80211. For example: &prompt.root; wlandebug -i ath0 +scan+auth+debug+assoc net.wlan.0.debug: 0 => 0xc80000<assoc,auth,scan> can be used to enable console messages related to scanning for access points and doing the 802.11 protocol handshakes required to arrange communication. There are also many useful statistics maintained by the 802.11 layer; the wlanstats tool will dump these informations. These statistics should identify all errors identified by the 802.11 layer. Beware however that some errors are identified in the device drivers that lie below the 802.11 layer so they may not show up. To diagnose device-specific problems you need to refer to the drivers' documentation. If the above information does not help to clarify the problem, please submit a problem report and include output from the above tools. Pav Lucistnik Written by
pav@FreeBSD.org
 Bluetooth Bluetooth Introduction Bluetooth is a wireless technology for creating personal networks operating in the 2.4 GHz unlicensed band, with a range of 10 meters. Networks are usually formed ad-hoc from portable devices such as cellular phones, handhelds and laptops. Unlike the other popular wireless technology, Wi-Fi, Bluetooth offers higher level service profiles, e.g. FTP-like file servers, file pushing, voice transport, serial line emulation, and more. The Bluetooth stack in &os; is implemented using the Netgraph framework (see &man.netgraph.4;). A broad variety of Bluetooth USB dongles is supported by the &man.ng.ubt.4; driver. The Broadcom BCM2033 chip based Bluetooth devices are supported via the &man.ubtbcmfw.4; and &man.ng.ubt.4; drivers. The 3Com Bluetooth PC Card 3CRWB60-A is supported by the &man.ng.bt3c.4; driver. Serial and UART based Bluetooth devices are supported via &man.sio.4;, &man.ng.h4.4; and &man.hcseriald.8;. This section describes the use of the USB Bluetooth dongle. Plugging in the Device By default Bluetooth device drivers are available as kernel modules. Before attaching a device, you will need to load the driver into the kernel: &prompt.root; kldload ng_ubt If the Bluetooth device is present in the system during system startup, load the module from /boot/loader.conf: ng_ubt_load="YES" Plug in your USB dongle. The output similar to the following will appear on the console (or in syslog): ubt0: vendor 0x0a12 product 0x0001, rev 1.10/5.25, addr 2 ubt0: Interface 0 endpoints: interrupt=0x81, bulk-in=0x82, bulk-out=0x2 ubt0: Interface 1 (alt.config 5) endpoints: isoc-in=0x83, isoc-out=0x3, wMaxPacketSize=49, nframes=6, buffer size=294 Copy /usr/share/examples/netgraph/bluetooth/rc.bluetooth into some convenient place, like /etc/rc.bluetooth. This script is used to start and stop the Bluetooth stack. It is a good idea to stop the stack before unplugging the device, but it is not (usually) fatal. When starting the stack, you will receive output similar to the following: &prompt.root; /etc/rc.bluetooth start ubt0 BD_ADDR: 00:02:72:00:d4:1a Features: 0xff 0xff 0xf 00 00 00 00 00 <3-Slot> <5-Slot> <Encryption> <Slot offset> <Timing accuracy> <Switch> <Hold mode> <Sniff mode> <Park mode> <RSSI> <Channel quality> <SCO link> <HV2 packets> <HV3 packets> <u-law log> <A-law log> <CVSD> <Paging scheme> <Power control> <Transparent SCO data> Max. ACL packet size: 192 bytes Number of ACL packets: 8 Max. SCO packet size: 64 bytes Number of SCO packets: 8 HCI Host Controller Interface (HCI) Host Controller Interface (HCI) provides a command interface to the baseband controller and link manager, and access to hardware status and control registers. This interface provides a uniform method of accessing the Bluetooth baseband capabilities. HCI layer on the Host exchanges data and commands with the HCI firmware on the Bluetooth hardware. The Host Controller Transport Layer (i.e. physical bus) driver provides both HCI layers with the ability to exchange information with each other. A single Netgraph node of type hci is created for a single Bluetooth device. The HCI node is normally connected to the Bluetooth device driver node (downstream) and the L2CAP node (upstream). All HCI operations must be performed on the HCI node and not on the device driver node. Default name for the HCI node is devicehci. For more details refer to the &man.ng.hci.4; manual page. One of the most common tasks is discovery of Bluetooth devices in RF proximity. This operation is called inquiry. Inquiry and other HCI related operations are done with the &man.hccontrol.8; utility. The example below shows how to find out which Bluetooth devices are in range. You should receive the list of devices in a few seconds. Note that a remote device will only answer the inquiry if it put into discoverable mode. &prompt.user; hccontrol -n ubt0hci inquiry Inquiry result, num_responses=1 Inquiry result #0 BD_ADDR: 00:80:37:29:19:a4 Page Scan Rep. Mode: 0x1 Page Scan Period Mode: 00 Page Scan Mode: 00 Class: 52:02:04 Clock offset: 0x78ef Inquiry complete. Status: No error [00] BD_ADDR is unique address of a Bluetooth device, similar to MAC addresses of a network card. This address is needed for further communication with a device. It is possible to assign human readable name to a BD_ADDR. The /etc/bluetooth/hosts file contains information regarding the known Bluetooth hosts. The following example shows how to obtain human readable name that was assigned to the remote device: &prompt.user; hccontrol -n ubt0hci remote_name_request 00:80:37:29:19:a4 BD_ADDR: 00:80:37:29:19:a4 Name: Pav's T39 If you perform an inquiry on a remote Bluetooth device, it will find your computer as your.host.name (ubt0). The name assigned to the local device can be changed at any time. The Bluetooth system provides a point-to-point connection (only two Bluetooth units involved), or a point-to-multipoint connection. In the point-to-multipoint connection the connection is shared among several Bluetooth devices. The following example shows how to obtain the list of active baseband connections for the local device: &prompt.user; hccontrol -n ubt0hci read_connection_list Remote BD_ADDR Handle Type Mode Role Encrypt Pending Queue State 00:80:37:29:19:a4 41 ACL 0 MAST NONE 0 0 OPEN A connection handle is useful when termination of the baseband connection is required. Note, that it is normally not required to do it by hand. The stack will automatically terminate inactive baseband connections. &prompt.root; hccontrol -n ubt0hci disconnect 41 Connection handle: 41 Reason: Connection terminated by local host [0x16] Refer to hccontrol help for a complete listing of available HCI commands. Most of the HCI commands do not require superuser privileges. L2CAP Logical Link Control and Adaptation Protocol (L2CAP) Logical Link Control and Adaptation Protocol (L2CAP) provides connection-oriented and connectionless data services to upper layer protocols with protocol multiplexing capability and segmentation and reassembly operation. L2CAP permits higher level protocols and applications to transmit and receive L2CAP data packets up to 64 kilobytes in length. L2CAP is based around the concept of channels. Channel is a logical connection on top of baseband connection. Each channel is bound to a single protocol in a many-to-one fashion. Multiple channels can be bound to the same protocol, but a channel cannot be bound to multiple protocols. Each L2CAP packet received on a channel is directed to the appropriate higher level protocol. Multiple channels can share the same baseband connection. A single Netgraph node of type l2cap is created for a single Bluetooth device. The L2CAP node is normally connected to the Bluetooth HCI node (downstream) and Bluetooth sockets nodes (upstream). Default name for the L2CAP node is devicel2cap. For more details refer to the &man.ng.l2cap.4; manual page. A useful command is &man.l2ping.8;, which can be used to ping other devices. Some Bluetooth implementations might not return all of the data sent to them, so 0 bytes in the following example is normal. &prompt.root; l2ping -a 00:80:37:29:19:a4 0 bytes from 0:80:37:29:19:a4 seq_no=0 time=48.633 ms result=0 0 bytes from 0:80:37:29:19:a4 seq_no=1 time=37.551 ms result=0 0 bytes from 0:80:37:29:19:a4 seq_no=2 time=28.324 ms result=0 0 bytes from 0:80:37:29:19:a4 seq_no=3 time=46.150 ms result=0 The &man.l2control.8; utility is used to perform various operations on L2CAP nodes. This example shows how to obtain the list of logical connections (channels) and the list of baseband connections for the local device: &prompt.user; l2control -a 00:02:72:00:d4:1a read_channel_list L2CAP channels: Remote BD_ADDR SCID/ DCID PSM IMTU/ OMTU State 00:07:e0:00:0b:ca 66/ 64 3 132/ 672 OPEN &prompt.user; l2control -a 00:02:72:00:d4:1a read_connection_list L2CAP connections: Remote BD_ADDR Handle Flags Pending State 00:07:e0:00:0b:ca 41 O 0 OPEN Another diagnostic tool is &man.btsockstat.1;. It does a job similar to as &man.netstat.1; does, but for Bluetooth network-related data structures. The example below shows the same logical connection as &man.l2control.8; above. &prompt.user; btsockstat Active L2CAP sockets PCB Recv-Q Send-Q Local address/PSM Foreign address CID State c2afe900 0 0 00:02:72:00:d4:1a/3 00:07:e0:00:0b:ca 66 OPEN Active RFCOMM sessions L2PCB PCB Flag MTU Out-Q DLCs State c2afe900 c2b53380 1 127 0 Yes OPEN Active RFCOMM sockets PCB Recv-Q Send-Q Local address Foreign address Chan DLCI State c2e8bc80 0 250 00:02:72:00:d4:1a 00:07:e0:00:0b:ca 3 6 OPEN RFCOMM RFCOMM Protocol The RFCOMM protocol provides emulation of serial ports over the L2CAP protocol. The protocol is based on the ETSI standard TS 07.10. RFCOMM is a simple transport protocol, with additional provisions for emulating the 9 circuits of RS-232 (EIATIA-232-E) serial ports. The RFCOMM protocol supports up to 60 simultaneous connections (RFCOMM channels) between two Bluetooth devices. For the purposes of RFCOMM, a complete communication path involves two applications running on different devices (the communication endpoints) with a communication segment between them. RFCOMM is intended to cover applications that make use of the serial ports of the devices in which they reside. The communication segment is a Bluetooth link from one device to another (direct connect). RFCOMM is only concerned with the connection between the devices in the direct connect case, or between the device and a modem in the network case. RFCOMM can support other configurations, such as modules that communicate via Bluetooth wireless technology on one side and provide a wired interface on the other side. In &os; the RFCOMM protocol is implemented at the Bluetooth sockets layer. pairing Pairing of Devices By default, Bluetooth communication is not authenticated, and any device can talk to any other device. A Bluetooth device (for example, cellular phone) may choose to require authentication to provide a particular service (for example, Dial-Up service). Bluetooth authentication is normally done with PIN codes. A PIN code is an ASCII string up to 16 characters in length. User is required to enter the same PIN code on both devices. Once user has entered the PIN code, both devices will generate a link key. After that the link key can be stored either in the devices themselves or in a persistent storage. Next time both devices will use previously generated link key. The described above procedure is called pairing. Note that if the link key is lost by any device then pairing must be repeated. The &man.hcsecd.8; daemon is responsible for handling of all Bluetooth authentication requests. The default configuration file is /etc/bluetooth/hcsecd.conf. An example section for a cellular phone with the PIN code arbitrarily set to 1234 is shown below: device { bdaddr 00:80:37:29:19:a4; name "Pav's T39"; key nokey; pin "1234"; } There is no limitation on PIN codes (except length). Some devices (for example Bluetooth headsets) may have a fixed PIN code built in. The switch forces the &man.hcsecd.8; daemon to stay in the foreground, so it is easy to see what is happening. Set the remote device to receive pairing and initiate the Bluetooth connection to the remote device. The remote device should say that pairing was accepted, and request the PIN code. Enter the same PIN code as you have in hcsecd.conf. Now your PC and the remote device are paired. Alternatively, you can initiate pairing on the remote device. On &os; 5.5, 6.1 and newer, the following line can be added to the /etc/rc.conf file to have hcsecd started automatically on system start: hcsecd_enable="YES" The following is a sample of the hcsecd daemon output: hcsecd[16484]: Got Link_Key_Request event from 'ubt0hci', remote bdaddr 0:80:37:29:19:a4 hcsecd[16484]: Found matching entry, remote bdaddr 0:80:37:29:19:a4, name 'Pav's T39', link key doesn't exist hcsecd[16484]: Sending Link_Key_Negative_Reply to 'ubt0hci' for remote bdaddr 0:80:37:29:19:a4 hcsecd[16484]: Got PIN_Code_Request event from 'ubt0hci', remote bdaddr 0:80:37:29:19:a4 hcsecd[16484]: Found matching entry, remote bdaddr 0:80:37:29:19:a4, name 'Pav's T39', PIN code exists hcsecd[16484]: Sending PIN_Code_Reply to 'ubt0hci' for remote bdaddr 0:80:37:29:19:a4 SDP Service Discovery Protocol (SDP) The Service Discovery Protocol (SDP) provides the means for client applications to discover the existence of services provided by server applications as well as the attributes of those services. The attributes of a service include the type or class of service offered and the mechanism or protocol information needed to utilize the service. SDP involves communication between a SDP server and a SDP client. The server maintains a list of service records that describe the characteristics of services associated with the server. Each service record contains information about a single service. A client may retrieve information from a service record maintained by the SDP server by issuing a SDP request. If the client, or an application associated with the client, decides to use a service, it must open a separate connection to the service provider in order to utilize the service. SDP provides a mechanism for discovering services and their attributes, but it does not provide a mechanism for utilizing those services. Normally, a SDP client searches for services based on some desired characteristics of the services. However, there are times when it is desirable to discover which types of services are described by an SDP server's service records without any a priori information about the services. This process of looking for any offered services is called browsing. The Bluetooth SDP server &man.sdpd.8; and command line client &man.sdpcontrol.8; are included in the standard &os; installation. The following example shows how to perform a SDP browse query. &prompt.user; sdpcontrol -a 00:01:03:fc:6e:ec browse Record Handle: 00000000 Service Class ID List: Service Discovery Server (0x1000) Protocol Descriptor List: L2CAP (0x0100) Protocol specific parameter #1: u/int/uuid16 1 Protocol specific parameter #2: u/int/uuid16 1 Record Handle: 0x00000001 Service Class ID List: Browse Group Descriptor (0x1001) Record Handle: 0x00000002 Service Class ID List: LAN Access Using PPP (0x1102) Protocol Descriptor List: L2CAP (0x0100) RFCOMM (0x0003) Protocol specific parameter #1: u/int8/bool 1 Bluetooth Profile Descriptor List: LAN Access Using PPP (0x1102) ver. 1.0 ... and so on. Note that each service has a list of attributes (RFCOMM channel for example). Depending on the service you might need to make a note of some of the attributes. Some Bluetooth implementations do not support service browsing and may return an empty list. In this case it is possible to search for the specific service. The example below shows how to search for the OBEX Object Push (OPUSH) service: &prompt.user; sdpcontrol -a 00:01:03:fc:6e:ec search OPUSH Offering services on &os; to Bluetooth clients is done with the &man.sdpd.8; server. On &os; 5.5, 6.1 and newer, the following line can be added to the /etc/rc.conf file: sdpd_enable="YES" Then the sdpd daemon can be started with: &prompt.root; /etc/rc.d/sdpd start The local server application that wants to provide Bluetooth service to the remote clients will register service with the local SDP daemon. The example of such application is &man.rfcomm.pppd.8;. Once started it will register Bluetooth LAN service with the local SDP daemon. The list of services registered with the local SDP server can be obtained by issuing SDP browse query via local control channel: &prompt.root; sdpcontrol -l browse Dial-Up Networking (DUN) and Network Access with PPP (LAN) Profiles The Dial-Up Networking (DUN) profile is mostly used with modems and cellular phones. The scenarios covered by this profile are the following: use of a cellular phone or modem by a computer as a wireless modem for connecting to a dial-up Internet access server, or using other dial-up services; use of a cellular phone or modem by a computer to receive data calls. Network Access with PPP (LAN) profile can be used in the following situations: LAN access for a single Bluetooth device; LAN access for multiple Bluetooth devices; PC to PC (using PPP networking over serial cable emulation). In &os; both profiles are implemented with &man.ppp.8; and &man.rfcomm.pppd.8; - a wrapper that converts RFCOMM Bluetooth connection into something PPP can operate with. Before any profile can be used, a new PPP label in the /etc/ppp/ppp.conf must be created. Consult &man.rfcomm.pppd.8; manual page for examples. In the following example &man.rfcomm.pppd.8; will be used to open RFCOMM connection to remote device with BD_ADDR 00:80:37:29:19:a4 on DUN RFCOMM channel. The actual RFCOMM channel number will be obtained from the remote device via SDP. It is possible to specify RFCOMM channel by hand, and in this case &man.rfcomm.pppd.8; will not perform SDP query. Use &man.sdpcontrol.8; to find out RFCOMM channel on the remote device. &prompt.root; rfcomm_pppd -a 00:80:37:29:19:a4 -c -C dun -l rfcomm-dialup In order to provide Network Access with PPP (LAN) service the &man.sdpd.8; server must be running. A new entry for LAN clients must be created in the /etc/ppp/ppp.conf file. Consult &man.rfcomm.pppd.8; manual page for examples. Finally, start RFCOMM PPP server on valid RFCOMM channel number. The RFCOMM PPP server will automatically register Bluetooth LAN service with the local SDP daemon. The example below shows how to start RFCOMM PPP server. &prompt.root; rfcomm_pppd -s -C 7 -l rfcomm-server OBEX OBEX Object Push (OPUSH) Profile OBEX is a widely used protocol for simple file transfers between mobile devices. Its main use is in infrared communication, where it is used for generic file transfers between notebooks or PDAs, and for sending business cards or calendar entries between cellular phones and other devices with PIM applications. The OBEX server and client are implemented as a third-party package obexapp, which is available as comms/obexapp port. OBEX client is used to push and/or pull objects from the OBEX server. An object can, for example, be a business card or an appointment. The OBEX client can obtain RFCOMM channel number from the remote device via SDP. This can be done by specifying service name instead of RFCOMM channel number. Supported service names are: IrMC, FTRN and OPUSH. It is possible to specify RFCOMM channel as a number. Below is an example of an OBEX session, where device information object is pulled from the cellular phone, and a new object (business card) is pushed into the phone's directory. &prompt.user; obexapp -a 00:80:37:29:19:a4 -C IrMC obex> get telecom/devinfo.txt devinfo-t39.txt Success, response: OK, Success (0x20) obex> put new.vcf Success, response: OK, Success (0x20) obex> di Success, response: OK, Success (0x20) In order to provide OBEX Object Push service, &man.sdpd.8; server must be running. A root folder, where all incoming objects will be stored, must be created. The default path to the root folder is /var/spool/obex. Finally, start OBEX server on valid RFCOMM channel number. The OBEX server will automatically register OBEX Object Push service with the local SDP daemon. The example below shows how to start OBEX server. &prompt.root; obexapp -s -C 10 Serial Port Profile (SPP) The Serial Port Profile (SPP) allows Bluetooth devices to perform RS232 (or similar) serial cable emulation. The scenario covered by this profile deals with legacy applications using Bluetooth as a cable replacement, through a virtual serial port abstraction. The &man.rfcomm.sppd.1; utility implements the Serial Port profile. A pseudo tty is used as a virtual serial port abstraction. The example below shows how to connect to a remote device Serial Port service. Note that you do not have to specify a RFCOMM channel - &man.rfcomm.sppd.1; can obtain it from the remote device via SDP. If you would like to override this, specify a RFCOMM channel on the command line. &prompt.root; rfcomm_sppd -a 00:07:E0:00:0B:CA -t /dev/ttyp6 rfcomm_sppd[94692]: Starting on /dev/ttyp6... Once connected, the pseudo tty can be used as serial port: &prompt.root; cu -l ttyp6 Troubleshooting A remote device cannot connect Some older Bluetooth devices do not support role switching. By default, when &os; is accepting a new connection, it tries to perform a role switch and become master. Devices, which do not support this will not be able to connect. Note that role switching is performed when a new connection is being established, so it is not possible to ask the remote device if it does support role switching. There is a HCI option to disable role switching on the local side: &prompt.root; hccontrol -n ubt0hci write_node_role_switch 0 Something is going wrong, can I see what exactly is happening? Yes, you can. Use the third-party package hcidump, which is available as comms/hcidump port. The hcidump utility is similar to &man.tcpdump.1;. It can be used to display the content of the Bluetooth packets on the terminal and to dump the Bluetooth packets to a file. Andrew Thompson Written by Bridging Introduction IP subnet bridge It is sometimes useful to divide one physical network (such as an Ethernet segment) into two separate network segments without having to create IP subnets and use a router to connect the segments together. A device that connects two networks together in this fashion is called a bridge. A FreeBSD system with two network interface cards can act as a bridge. The bridge works by learning the MAC layer addresses (Ethernet addresses) of the devices on each of its network interfaces. It forwards traffic between two networks only when its source and destination are on different networks. In many respects, a bridge is like an Ethernet switch with very few ports. Situations Where Bridging Is Appropriate There are many common situations in which a bridge is used today. Connecting Networks The basic operation of a bridge is to join two or more network segments together. There are many reasons to use a host based bridge over plain networking equipment such as cabling constraints, firewalling or connecting pseudo networks such as a Virtual Machine interface. A bridge can also connect a wireless interface running in hostap mode to a wired network and act as an access point. Filtering/Traffic Shaping Firewall firewall NAT A common situation is where firewall functionality is needed without routing or network address translation (NAT). An example is a small company that is connected via DSL or ISDN to their ISP. They have a 13 globally-accessible IP addresses from their ISP and have 10 PCs on their network. In this situation, using a router-based firewall is difficult because of subnetting issues. router DSL ISDN A bridge-based firewall can be configured and dropped into the path just downstream of their DSL/ISDN router without any IP numbering issues. Network Tap A bridge can join two network segments and be used to inspect all Ethernet frames that pass between them. This can either be from using &man.bpf.4;/&man.tcpdump.1; on the bridge interface or by sending a copy of all frames out an additional interface (span port). Layer 2 VPN Two Ethernet networks can be joined across an IP link by bridging the networks to an EtherIP tunnel or a &man.tap.4; based solution such as OpenVPN. Layer 2 Redundancy A network can be connected together with multiple links and use the Spanning Tree Protocol to block redundant paths. For an Ethernet network to function properly only one active path can exist between two devices, Spanning Tree will detect loops and put the redundant links into a blocked state. Should one of the active links fail then the protocol will calculate a different tree and reenable one of the blocked paths to restore connectivity to all points in the network. Kernel Configuration This section covers &man.if.bridge.4; bridge implementation, a netgraph bridging driver is also available, for more information see &man.ng.bridge.4; manual page. The bridge driver is a kernel module and will be automatically loaded by &man.ifconfig.8; when creating a bridge interface. It is possible to compile the bridge in to the kernel by adding device if_bridge to your kernel configuration file. Packet filtering can be used with any firewall package that hooks in via the &man.pfil.9; framework. The firewall can be loaded as a module or compiled into the kernel. The bridge can be used as a traffic shaper with &man.altq.4; or &man.dummynet.4;. Enabling the Bridge The bridge is created using interface cloning. To create a bridge use &man.ifconfig.8;, if the bridge driver is not present in the kernel then it will be loaded automatically. &prompt.root; ifconfig bridge create bridge0 &prompt.root; ifconfig bridge0 bridge0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500 ether 96:3d:4b:f1:79:7a id 00:00:00:00:00:00 priority 32768 hellotime 2 fwddelay 15 maxage 20 holdcnt 6 proto rstp maxaddr 100 timeout 1200 root id 00:00:00:00:00:00 priority 0 ifcost 0 port 0 A bridge interface is created and is automatically assigned a randomly generated Ethernet address. The maxaddr and timeout parameters control how many MAC addresses the bridge will keep in its forwarding table and how many seconds before each entry is removed after it is last seen. The other parameters control how Spanning Tree operates. Add the member network interfaces to the bridge. For the bridge to forward packets all member interfaces and the bridge need to be up: &prompt.root; ifconfig bridge0 addm fxp0 addm fxp1 up &prompt.root; ifconfig fxp0 up &prompt.root; ifconfig fxp1 up The bridge is now forwarding Ethernet frames between fxp0 and fxp1. The equivalent configuration in /etc/rc.conf so the bridge is created at startup is: cloned_interfaces="bridge0" ifconfig_bridge0="addm fxp0 addm fxp1 up" ifconfig_fxp0="up" ifconfig_fxp1="up" If the bridge host needs an IP address then the correct place to set this is on the bridge interface itself rather than one of the member interfaces. This can be set statically or via DHCP: &prompt.root; ifconfig bridge0 inet 192.168.0.1/24 It is also possible to assign an IPv6 address to a bridge interface. Firewalling firewall When packet filtering is enabled, bridged packets will pass through the filter inbound on the originating interface, on the bridge interface and outbound on the appropriate interfaces. Either stage can be disabled. When direction of the packet flow is important it is best to firewall on the member interfaces rather than the bridge itself. The bridge has several configurable settings for passing non-IP and ARP packets, and layer2 firewalling with IPFW. See &man.if.bridge.4; for more information. Spanning Tree The bridge driver implements the Rapid Spanning Tree Protocol (RSTP or 802.1w) with backwards compatibility with the legacy Spanning Tree Protocol (STP). Spanning Tree is used to detect and remove loops in a network topology. RSTP provides faster Spanning Tree convergence than legacy STP, the protocol will exchange information with neighbouring switches to quickly transition to forwarding without creating loops. The following table shows the supported operating modes: OS Version STP Modes Default Mode &os; 5.4—&os; 6.2 STP STP &os; 6.3+ RSTP or STP STP &os; 7.0+ RSTP or STP RSTP Spanning Tree can be enabled on member interfaces using the stp command. For a bridge with fxp0 and fxp1 as the current interfaces, enable STP with the following: &prompt.root; ifconfig bridge0 stp fxp0 stp fxp1 bridge0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500 ether d6:cf:d5:a0:94:6d id 00:01:02:4b:d4:50 priority 32768 hellotime 2 fwddelay 15 maxage 20 holdcnt 6 proto rstp maxaddr 100 timeout 1200 root id 00:01:02:4b:d4:50 priority 32768 ifcost 0 port 0 member: fxp0 flags=1c7<LEARNING,DISCOVER,STP,AUTOEDGE,PTP,AUTOPTP> port 3 priority 128 path cost 200000 proto rstp role designated state forwarding member: fxp1 flags=1c7<LEARNING,DISCOVER,STP,AUTOEDGE,PTP,AUTOPTP> port 4 priority 128 path cost 200000 proto rstp role designated state forwarding This bridge has a spanning tree ID of 00:01:02:4b:d4:50 and a priority of 32768. As the root id is the same it indicates that this is the root bridge for the tree. Another bridge on the network also has spanning tree enabled: bridge0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500 ether 96:3d:4b:f1:79:7a id 00:13:d4:9a:06:7a priority 32768 hellotime 2 fwddelay 15 maxage 20 holdcnt 6 proto rstp maxaddr 100 timeout 1200 root id 00:01:02:4b:d4:50 priority 32768 ifcost 400000 port 4 member: fxp0 flags=1c7<LEARNING,DISCOVER,STP,AUTOEDGE,PTP,AUTOPTP> port 4 priority 128 path cost 200000 proto rstp role root state forwarding member: fxp1 flags=1c7<LEARNING,DISCOVER,STP,AUTOEDGE,PTP,AUTOPTP> port 5 priority 128 path cost 200000 proto rstp role designated state forwarding The line root id 00:01:02:4b:d4:50 priority 32768 ifcost 400000 port 4 shows that the root bridge is 00:01:02:4b:d4:50 as above and has a path cost of 400000 from this bridge, the path to the root bridge is via port 4 which is fxp0. Advanced Bridging Reconstruct Traffic Flows The bridge supports monitor mode, where the packets are discarded after &man.bpf.4; processing, and are not processed or forwarded further. This can be used to multiplex the input of two or more interfaces into a single &man.bpf.4; stream. This is useful for reconstructing the traffic for network taps that transmit the RX/TX signals out through two separate interfaces. To read the input from four network interfaces as one stream: &prompt.root; ifconfig bridge0 addm fxp0 addm fxp1 addm fxp2 addm fxp3 monitor up &prompt.root; tcpdump -i bridge0 Span Ports A copy of every Ethernet frame received by the bridge will be transmitted out a designated span port. The number of span ports configured on a bridge is unlimited, if an interface is designated as a span port then it may not also be used as a regular bridge port. This is most useful for snooping a bridged network passively on another host connected to one of the span ports of the bridge. To send a copy of all frames out the interface named fxp4: &prompt.root; ifconfig bridge0 span fxp4 Private Interfaces A private interface does not forward any traffic to any other port that is also a private interface. The traffic is blocked unconditionally so no Ethernet frames will be forwarded, including ARP. If traffic needs to be selectively blocked then a firewall should be used instead. Sticky Interfaces If a bridge member interface is marked as sticky then dynamically learned address entries are treated at static once entered into the forwarding cache. Sticky entries are never aged out of the cache or replaced, even if the address is seen on a different interface. This gives the benefit of static address entries without the need to pre-populate the forwarding table, clients learnt on a particular segment of the bridge can not roam to another segment. Another example of using sticky addresses would be to combine the bridge with VLANs to create a router where customer networks are isolated without wasting IP address space. Consider that CustomerA is on vlan100 and CustomerB is on vlan101. The bridge has the address 192.168.0.1 and is also an internet router. &prompt.root; ifconfig bridge0 addm vlan100 sticky vlan100 addm vlan101 sticky vlan101 &prompt.root; ifconfig bridge0 inet 192.168.0.1/24 Both clients see 192.168.0.1 as their default gateway and since the bridge cache is sticky they can not spoof the MAC address of the other customer to intercept their traffic. Any communication between the VLANs can be blocked using private interfaces (or a firewall): &prompt.root; ifconfig bridge0 private vlan100 private vlan101 The customers are completely isolated from each other, the full /24 address range can be allocated without subnetting. Address limits The number of unique source MAC addresses behind an - interface can limited. Once the limit is reached packets + interface can be limited. Once the limit is reached packets with unknown source addresses are dropped until an existing host cache entry expires or is removed. The following example sets the maximum number of Ethernet devices for CustomerA on vlan100 to 10. &prompt.root; ifconfig bridge0 ifmaxaddr vlan100 10 SNMP Monitoring The bridge interface and STP parameters can be monitored via the SNMP daemon which is included in the &os; base system. The exported bridge MIBs conform to the IETF standards so any SNMP client or monitoring package can be used to retrieve the data. On the bridge machine uncomment the begemotSnmpdModulePath."bridge" = "/usr/lib/snmp_bridge.so" line from /etc/snmp.config and start the bsnmpd daemon. Other configuration such as community names and access lists may need to be modified. See &man.bsnmpd.1; and &man.snmp.bridge.3; for more information. The following examples use the Net-SNMP software (net-mgmt/net-snmp) to query a bridge, the net-mgmt/bsnmptools port can also be used. From the SNMP client host add to $HOME/.snmp/snmp.conf the following lines to import the bridge MIB definitions in to Net-SNMP: mibdirs +/usr/share/snmp/mibs mibs +BRIDGE-MIB:RSTP-MIB:BEGEMOT-MIB:BEGEMOT-BRIDGE-MIB To monitor a single bridge via the IETF BRIDGE-MIB (RFC4188) do &prompt.user; snmpwalk -v 2c -c public bridge1.example.com mib-2.dot1dBridge BRIDGE-MIB::dot1dBaseBridgeAddress.0 = STRING: 66:fb:9b:6e:5c:44 BRIDGE-MIB::dot1dBaseNumPorts.0 = INTEGER: 1 ports BRIDGE-MIB::dot1dStpTimeSinceTopologyChange.0 = Timeticks: (189959) 0:31:39.59 centi-seconds BRIDGE-MIB::dot1dStpTopChanges.0 = Counter32: 2 BRIDGE-MIB::dot1dStpDesignatedRoot.0 = Hex-STRING: 80 00 00 01 02 4B D4 50 ... BRIDGE-MIB::dot1dStpPortState.3 = INTEGER: forwarding(5) BRIDGE-MIB::dot1dStpPortEnable.3 = INTEGER: enabled(1) BRIDGE-MIB::dot1dStpPortPathCost.3 = INTEGER: 200000 BRIDGE-MIB::dot1dStpPortDesignatedRoot.3 = Hex-STRING: 80 00 00 01 02 4B D4 50 BRIDGE-MIB::dot1dStpPortDesignatedCost.3 = INTEGER: 0 BRIDGE-MIB::dot1dStpPortDesignatedBridge.3 = Hex-STRING: 80 00 00 01 02 4B D4 50 BRIDGE-MIB::dot1dStpPortDesignatedPort.3 = Hex-STRING: 03 80 BRIDGE-MIB::dot1dStpPortForwardTransitions.3 = Counter32: 1 RSTP-MIB::dot1dStpVersion.0 = INTEGER: rstp(2) The dot1dStpTopChanges.0 value is two which means that the STP bridge topology has changed twice, a topology change means that one or more links in the network have changed or failed and a new tree has been calculated. The dot1dStpTimeSinceTopologyChange.0 value will show when this happened. To monitor multiple bridge interfaces one may use the private BEGEMOT-BRIDGE-MIB: &prompt.user; snmpwalk -v 2c -c public bridge1.example.com enterprises.fokus.begemot.begemotBridge BEGEMOT-BRIDGE-MIB::begemotBridgeBaseName."bridge0" = STRING: bridge0 BEGEMOT-BRIDGE-MIB::begemotBridgeBaseName."bridge2" = STRING: bridge2 BEGEMOT-BRIDGE-MIB::begemotBridgeBaseAddress."bridge0" = STRING: e:ce:3b:5a:9e:13 BEGEMOT-BRIDGE-MIB::begemotBridgeBaseAddress."bridge2" = STRING: 12:5e:4d:74:d:fc BEGEMOT-BRIDGE-MIB::begemotBridgeBaseNumPorts."bridge0" = INTEGER: 1 BEGEMOT-BRIDGE-MIB::begemotBridgeBaseNumPorts."bridge2" = INTEGER: 1 ... BEGEMOT-BRIDGE-MIB::begemotBridgeStpTimeSinceTopologyChange."bridge0" = Timeticks: (116927) 0:19:29.27 centi-seconds BEGEMOT-BRIDGE-MIB::begemotBridgeStpTimeSinceTopologyChange."bridge2" = Timeticks: (82773) 0:13:47.73 centi-seconds BEGEMOT-BRIDGE-MIB::begemotBridgeStpTopChanges."bridge0" = Counter32: 1 BEGEMOT-BRIDGE-MIB::begemotBridgeStpTopChanges."bridge2" = Counter32: 1 BEGEMOT-BRIDGE-MIB::begemotBridgeStpDesignatedRoot."bridge0" = Hex-STRING: 80 00 00 40 95 30 5E 31 BEGEMOT-BRIDGE-MIB::begemotBridgeStpDesignatedRoot."bridge2" = Hex-STRING: 80 00 00 50 8B B8 C6 A9 To change the bridge interface being monitored via the mib-2.dot1dBridge subtree do: &prompt.user; snmpset -v 2c -c private bridge1.example.com BEGEMOT-BRIDGE-MIB::begemotBridgeDefaultBridgeIf.0 s bridge2 Andrew Thompson Written by Link Aggregation and Failover lagg failover fec lacp loadbalance roundrobin Introduction The &man.lagg.4; interface allows aggregation of multiple network interfaces as one virtual interface for the purpose of providing fault-tolerance and high-speed links. Operating Modes failover Sends and receives traffic only through the master port. If the master port becomes unavailable, the next active port is used. The first interface added is the master port; any interfaces added after that are used as failover devices. fec Supports Cisco EtherChannel. This is a static setup and does not negotiate aggregation with the peer or exchange frames to monitor the link, if the switch supports LACP then that should be used instead. Balances outgoing traffic across the active ports based on hashed protocol header information and accepts incoming traffic from any active port. The hash includes the Ethernet source and destination address, and, if available, the VLAN tag, and the IPv4/IPv6 source and destination address. lacp Supports the IEEE 802.3ad Link Aggregation Control Protocol (LACP) and the Marker Protocol. LACP will negotiate a set of aggregable links with the peer in to one or more Link Aggregated Groups. Each LAG is composed of ports of the same speed, set to full-duplex operation. The traffic will be balanced across the ports in the LAG with the greatest total speed, in most cases there will only be one LAG which contains all ports. In the event of changes in physical connectivity, Link Aggregation will quickly converge to a new configuration. Balances outgoing traffic across the active ports based on hashed protocol header information and accepts incoming traffic from any active port. The hash includes the Ethernet source and destination address, and, if available, the VLAN tag, and the IPv4/IPv6 source and destination address. loadbalance This is an alias of fec mode. roundrobin Distributes outgoing traffic using a round-robin scheduler through all active ports and accepts incoming traffic from any active port. This mode will violate Ethernet frame ordering and should be used with caution. Examples LACP aggregation with a Cisco switch This example connects two interfaces on a &os; machine to the switch as a single load balanced and fault tolerant link. More interfaces can be added to increase throughput and fault tolerance. Since frame ordering is mandatory on Ethernet links then any traffic between two stations always flows over the same physical link limiting the maximum speed to that of one interface. The transmit algorithm attempts to use as much information as it can to distinguish different traffic flows and balance across the available interfaces. On the Cisco switch add the interfaces to the channel group. interface FastEthernet0/1 channel-group 1 mode active channel-protocol lacp ! interface FastEthernet0/2 channel-group 1 mode active channel-protocol lacp ! On the &os; machine create the lagg interface. &prompt.root; ifconfig lagg0 create &prompt.root; ifconfig lagg0 up laggproto lacp laggport fxp0 laggport fxp1 View the interface status from ifconfig; ports marked as ACTIVE are part of the active aggregation group that has been negotiated with the remote switch and traffic will be transmitted and received. Use the verbose output of &man.ifconfig.8; to view the LAG identifiers. lagg0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=8<VLAN_MTU> ether 00:05:5d:71:8d:b8 media: Ethernet autoselect status: active laggproto lacp laggport: fxp1 flags=1c<ACTIVE,COLLECTING,DISTRIBUTING> laggport: fxp0 flags=1c<ACTIVE,COLLECTING,DISTRIBUTING> The switch will show which ports are active. For more detail use show lacp neighbor detail. switch# show lacp neighbor Flags: S - Device is requesting Slow LACPDUs F - Device is requesting Fast LACPDUs A - Device is in Active mode P - Device is in Passive mode Channel group 1 neighbors Partner's information: LACP port Oper Port Port Port Flags Priority Dev ID Age Key Number State Fa0/1 SA 32768 0005.5d71.8db8 29s 0x146 0x3 0x3D Fa0/2 SA 32768 0005.5d71.8db8 29s 0x146 0x4 0x3D Failover mode Failover mode can be used to switch over to another interface if the link is lost on the master. &prompt.root; ifconfig lagg0 create &prompt.root; ifconfig lagg0 up laggproto failover laggport fxp0 laggport fxp1 lagg0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=8<VLAN_MTU> ether 00:05:5d:71:8d:b8 media: Ethernet autoselect status: active laggproto failover laggport: fxp1 flags=0<> laggport: fxp0 flags=5<MASTER,ACTIVE> Traffic will be transmitted and received on fxp0. If the link is lost on fxp0 then fxp1 will become the active link. If the link is restored on the master interface then it will once again become the active link. Jean-François Dockès Updated by Alex Dupre Reorganized and enhanced by Diskless Operation diskless workstation diskless operation A FreeBSD machine can boot over the network and operate without a local disk, using file systems mounted from an NFS server. No system modification is necessary, beyond standard configuration files. Such a system is relatively easy to set up because all the necessary elements are readily available: There are at least two possible methods to load the kernel over the network: PXE: The &intel; Preboot eXecution Environment system is a form of smart boot ROM built into some networking cards or motherboards. See &man.pxeboot.8; for more details. The Etherboot port (net/etherboot) produces ROM-able code to boot kernels over the network. The code can be either burnt into a boot PROM on a network card, or loaded from a local floppy (or hard) disk drive, or from a running &ms-dos; system. Many network cards are supported. A sample script (/usr/share/examples/diskless/clone_root) eases the creation and maintenance of the workstation's root file system on the server. The script will probably require a little customization but it will get you started very quickly. Standard system startup files exist in /etc to detect and support a diskless system startup. Swapping, if needed, can be done either to an NFS file or to a local disk. There are many ways to set up diskless workstations. Many elements are involved, and most can be customized to suit local taste. The following will describe variations on the setup of a complete system, emphasizing simplicity and compatibility with the standard FreeBSD startup scripts. The system described has the following characteristics: The diskless workstations use a shared read-only / file system, and a shared read-only /usr. The root file system is a copy of a standard FreeBSD root (typically the server's), with some configuration files overridden by ones specific to diskless operation or, possibly, to the workstation they belong to. The parts of the root which have to be writable are overlaid with &man.md.4; file systems. Any changes will be lost when the system reboots. The kernel is transferred and loaded either with Etherboot or PXE as some situations may mandate the use of either method. As described, this system is insecure. It should live in a protected area of a network, and be untrusted by other hosts. All the information in this section has been tested using &os; 5.2.1-RELEASE. Background Information Setting up diskless workstations is both relatively straightforward and prone to errors. These are sometimes difficult to diagnose for a number of reasons. For example: Compile time options may determine different behaviors at runtime. Error messages are often cryptic or totally absent. In this context, having some knowledge of the background mechanisms involved is very useful to solve the problems that may arise. Several operations need to be performed for a successful bootstrap: The machine needs to obtain initial parameters such as its IP address, executable filename, server name, root path. This is done using the DHCP or BOOTP protocols. DHCP is a compatible extension of BOOTP, and uses the same port numbers and basic packet format. It is possible to configure a system to use only BOOTP. The &man.bootpd.8; server program is included in the base &os; system. However, DHCP has a number of advantages over BOOTP (nicer configuration files, possibility of using PXE, plus many others not directly related to diskless operation), and we will describe mainly a DHCP configuration, with equivalent examples using &man.bootpd.8; when possible. The sample configuration will use the ISC DHCP software package (release 3.0.1.r12 was installed on the test server). The machine needs to transfer one or several programs to local memory. Either TFTP or NFS are used. The choice between TFTP and NFS is a compile time option in several places. A common source of error is to specify filenames for the wrong protocol: TFTP typically transfers all files from a single directory on the server, and would expect filenames relative to this directory. NFS needs absolute file paths. The possible intermediate bootstrap programs and the kernel need to be initialized and executed. There are several important variations in this area: PXE will load &man.pxeboot.8;, which is a modified version of the &os; third stage loader. The &man.loader.8; will obtain most parameters necessary to system startup, and leave them in the kernel environment before transferring control. It is possible to use a GENERIC kernel in this case. Etherboot, will directly load the kernel, with less preparation. You will need to build a kernel with specific options. PXE and Etherboot work equally well; however, because kernels normally let the &man.loader.8; do more work for them, PXE is the preferred method. If your BIOS and network cards support PXE, you should probably use it. Finally, the machine needs to access its file systems. NFS is used in all cases. See also &man.diskless.8; manual page. Setup Instructions Configuration Using <application>ISC DHCP</application> DHCP diskless operation The ISC DHCP server can answer both BOOTP and DHCP requests. ISC DHCP 3.0 is not part of the base system. You will first need to install the net/isc-dhcp3-server port or the corresponding package. Once ISC DHCP is installed, it needs a configuration file to run (normally named /usr/local/etc/dhcpd.conf). Here follows a commented example, where host margaux uses Etherboot and host corbieres uses PXE: default-lease-time 600; max-lease-time 7200; authoritative; option domain-name "example.com"; option domain-name-servers 192.168.4.1; option routers 192.168.4.1; subnet 192.168.4.0 netmask 255.255.255.0 { use-host-decl-names on; option subnet-mask 255.255.255.0; option broadcast-address 192.168.4.255; host margaux { hardware ethernet 01:23:45:67:89:ab; fixed-address margaux.example.com; next-server 192.168.4.4; filename "/data/misc/kernel.diskless"; option root-path "192.168.4.4:/data/misc/diskless"; } host corbieres { hardware ethernet 00:02:b3:27:62:df; fixed-address corbieres.example.com; next-server 192.168.4.4; filename "pxeboot"; option root-path "192.168.4.4:/data/misc/diskless"; } } This option tells dhcpd to send the value in the host declarations as the hostname for the diskless host. An alternate way would be to add an option host-name margaux inside the host declarations. The next-server directive designates the TFTP or NFS server to use for loading loader or kernel file (the default is to use the same host as the DHCP server). The filename directive defines the file that Etherboot or PXE will load for the next execution step. It must be specified according to the transfer method used. Etherboot can be compiled to use NFS or TFTP. The &os; port configures NFS by default. PXE uses TFTP, which is why a relative filename is used here (this may depend on the TFTP server configuration, but would be fairly typical). Also, PXE loads pxeboot, not the kernel. There are other interesting possibilities, like loading pxeboot from a &os; CD-ROM /boot directory (as &man.pxeboot.8; can load a GENERIC kernel, this makes it possible to use PXE to boot from a remote CD-ROM). The root-path option defines the path to the root file system, in usual NFS notation. When using PXE, it is possible to leave off the host's IP as long as you do not enable the kernel option BOOTP. The NFS server will then be the same as the TFTP one. Configuration Using BOOTP BOOTP diskless operation Here follows an equivalent bootpd configuration (reduced to one client). This would be found in /etc/bootptab. Please note that Etherboot must be compiled with the non-default option NO_DHCP_SUPPORT in order to use BOOTP, and that PXE needs DHCP. The only obvious advantage of bootpd is that it exists in the base system. .def100:\ :hn:ht=1:sa=192.168.4.4:vm=rfc1048:\ :sm=255.255.255.0:\ :ds=192.168.4.1:\ :gw=192.168.4.1:\ :hd="/tftpboot":\ :bf="/kernel.diskless":\ :rp="192.168.4.4:/data/misc/diskless": margaux:ha=0123456789ab:tc=.def100 Preparing a Boot Program with <application>Etherboot</application> Etherboot Etherboot's Web site contains extensive documentation mainly intended for Linux systems, but nonetheless containing useful information. The following will just outline how you would use Etherboot on a FreeBSD system. You must first install the net/etherboot package or port. You can change the Etherboot configuration (i.e. to use TFTP instead of NFS) by editing the Config file in the Etherboot source directory. For our setup, we shall use a boot floppy. For other methods (PROM, or &ms-dos; program), please refer to the Etherboot documentation. To make a boot floppy, insert a floppy in the drive on the machine where you installed Etherboot, then change your current directory to the src directory in the Etherboot tree and type: &prompt.root; gmake bin32/devicetype.fd0 devicetype depends on the type of the Ethernet card in the diskless workstation. Refer to the NIC file in the same directory to determine the right devicetype. Booting with <acronym>PXE</acronym> By default, the &man.pxeboot.8; loader loads the kernel via NFS. It can be compiled to use TFTP instead by specifying the LOADER_TFTP_SUPPORT option in /etc/make.conf. See the comments in /usr/share/examples/etc/make.conf for instructions. There are two other make.conf options which may be useful for setting up a serial console diskless machine: BOOT_PXELDR_PROBE_KEYBOARD, and BOOT_PXELDR_ALWAYS_SERIAL. To use PXE when the machine starts, you will usually need to select the Boot from network option in your BIOS setup, or type a function key during the PC initialization. Configuring the <acronym>TFTP</acronym> and <acronym>NFS</acronym> Servers TFTP diskless operation NFS diskless operation If you are using PXE or Etherboot configured to use TFTP, you need to enable tftpd on the file server: Create a directory from which tftpd will serve the files, e.g. /tftpboot. Add this line to your /etc/inetd.conf: tftp dgram udp wait root /usr/libexec/tftpd tftpd -l -s /tftpboot It appears that at least some PXE versions want the TCP version of TFTP. In this case, add a second line, replacing dgram udp with stream tcp. Tell inetd to reread its configuration file. The must be in the /etc/rc.conf file for this command to execute correctly: &prompt.root; /etc/rc.d/inetd restart You can place the tftpboot directory anywhere on the server. Make sure that the location is set in both inetd.conf and dhcpd.conf. In all cases, you also need to enable NFS and export the appropriate file system on the NFS server. Add this to /etc/rc.conf: nfs_server_enable="YES" Export the file system where the diskless root directory is located by adding the following to /etc/exports (adjust the volume mount point and replace margaux corbieres with the names of the diskless workstations): /data/misc -alldirs -ro margaux corbieres Tell mountd to reread its configuration file. If you actually needed to enable NFS in /etc/rc.conf at the first step, you probably want to reboot instead. &prompt.root; /etc/rc.d/mountd restart Building a Diskless Kernel diskless operation kernel configuration If using Etherboot, you need to create a kernel configuration file for the diskless client with the following options (in addition to the usual ones): options BOOTP # Use BOOTP to obtain IP address/hostname options BOOTP_NFSROOT # NFS mount root file system using BOOTP info You may also want to use BOOTP_NFSV3, BOOT_COMPAT and BOOTP_WIRED_TO (refer to NOTES). These option names are historical and slightly misleading as they actually enable indifferent use of DHCP and BOOTP inside the kernel (it is also possible to force strict BOOTP or DHCP use). Build the kernel (see ), and copy it to the place specified in dhcpd.conf. When using PXE, building a kernel with the above options is not strictly necessary (though suggested). Enabling them will cause more DHCP requests to be issued during kernel startup, with a small risk of inconsistency between the new values and those retrieved by &man.pxeboot.8; in some special cases. The advantage of using them is that the host name will be set as a side effect. Otherwise you will need to set the host name by another method, for example in a client-specific rc.conf file. In order to be loadable with Etherboot, a kernel needs to have the device hints compiled in. You would typically set the following option in the configuration file (see the NOTES configuration comments file): hints "GENERIC.hints" Preparing the Root Filesystem root file system diskless operation You need to create a root file system for the diskless workstations, in the location listed as root-path in dhcpd.conf. Using <command>make world</command> to populate root This method is quick and will install a complete virgin system (not only the root file system) into DESTDIR. All you have to do is simply execute the following script: #!/bin/sh export DESTDIR=/data/misc/diskless mkdir -p ${DESTDIR} cd /usr/src; make buildworld && make buildkernel cd /usr/src/etc; make distribution Once done, you may need to customize your /etc/rc.conf and /etc/fstab placed into DESTDIR according to your needs. Configuring Swap If needed, a swap file located on the server can be accessed via NFS. <acronym>NFS</acronym> Swap The kernel does not support enabling NFS swap at boot time. Swap must be enabled by the startup scripts, by mounting a writable file system and creating and enabling a swap file. To create a swap file of appropriate size, you can do like this: &prompt.root; dd if=/dev/zero of=/path/to/swapfile bs=1k count=1 oseek=100000 To enable it you have to add the following line to your rc.conf: swapfile=/path/to/swapfile Miscellaneous Issues Running with a Read-only <filename>/usr</filename> diskless operation /usr read-only If the diskless workstation is configured to run X, you will have to adjust the XDM configuration file, which puts the error log on /usr by default. Using a Non-FreeBSD Server When the server for the root file system is not running FreeBSD, you will have to create the root file system on a FreeBSD machine, then copy it to its destination, using tar or cpio. In this situation, there are sometimes problems with the special files in /dev, due to differing major/minor integer sizes. A solution to this problem is to export a directory from the non-FreeBSD server, mount this directory onto a FreeBSD machine, and use &man.devfs.5; to allocate device nodes transparently for the user. ISDN ISDN A good resource for information on ISDN technology and hardware is Dan Kegel's ISDN Page. A quick simple road map to ISDN follows: If you live in Europe you might want to investigate the ISDN card section. If you are planning to use ISDN primarily to connect to the Internet with an Internet Provider on a dial-up non-dedicated basis, you might look into Terminal Adapters. This will give you the most flexibility, with the fewest problems, if you change providers. If you are connecting two LANs together, or connecting to the Internet with a dedicated ISDN connection, you might consider the stand alone router/bridge option. Cost is a significant factor in determining what solution you will choose. The following options are listed from least expensive to most expensive. Hellmuth Michaelis Contributed by ISDN Cards ISDN cards FreeBSD's ISDN implementation supports only the DSS1/Q.931 (or Euro-ISDN) standard using passive cards. Some active cards are supported where the firmware also supports other signaling protocols; this also includes the first supported Primary Rate (PRI) ISDN card. The isdn4bsd software allows you to connect to other ISDN routers using either IP over raw HDLC or by using synchronous PPP: either by using kernel PPP with isppp, a modified &man.sppp.4; driver, or by using userland &man.ppp.8;. By using userland &man.ppp.8;, channel bonding of two or more ISDN B-channels is possible. A telephone answering machine application is also available as well as many utilities such as a software 300 Baud modem. Some growing number of PC ISDN cards are supported under FreeBSD and the reports show that it is successfully used all over Europe and in many other parts of the world. The passive ISDN cards supported are mostly the ones with the Infineon (formerly Siemens) ISAC/HSCX/IPAC ISDN chipsets, but also ISDN cards with chips from Cologne Chip (ISA bus only), PCI cards with Winbond W6692 chips, some cards with the Tiger300/320/ISAC chipset combinations and some vendor specific chipset based cards such as the AVM Fritz!Card PCI V.1.0 and the AVM Fritz!Card PnP. Currently the active supported ISDN cards are the AVM B1 (ISA and PCI) BRI cards and the AVM T1 PCI PRI cards. For documentation on isdn4bsd, have a look at /usr/share/examples/isdn/ directory on your FreeBSD system or at the homepage of isdn4bsd which also has pointers to hints, erratas and much more documentation such as the isdn4bsd handbook. In case you are interested in adding support for a different ISDN protocol, a currently unsupported ISDN PC card or otherwise enhancing isdn4bsd, please get in touch with &a.hm;. For questions regarding the installation, configuration and troubleshooting isdn4bsd, a &a.isdn.name; mailing list is available. ISDN Terminal Adapters Terminal adapters (TA), are to ISDN what modems are to regular phone lines. modem Most TA's use the standard Hayes modem AT command set, and can be used as a drop in replacement for a modem. A TA will operate basically the same as a modem except connection and throughput speeds will be much faster than your old modem. You will need to configure PPP exactly the same as for a modem setup. Make sure you set your serial speed as high as possible. PPP The main advantage of using a TA to connect to an Internet Provider is that you can do Dynamic PPP. As IP address space becomes more and more scarce, most providers are not willing to provide you with a static IP anymore. Most stand-alone routers are not able to accommodate dynamic IP allocation. TA's completely rely on the PPP daemon that you are running for their features and stability of connection. This allows you to upgrade easily from using a modem to ISDN on a FreeBSD machine, if you already have PPP set up. However, at the same time any problems you experienced with the PPP program and are going to persist. If you want maximum stability, use the kernel PPP option, not the userland PPP. The following TA's are known to work with FreeBSD: Motorola BitSurfer and Bitsurfer Pro Adtran Most other TA's will probably work as well, TA vendors try to make sure their product can accept most of the standard modem AT command set. The real problem with external TA's is that, like modems, you need a good serial card in your computer. You should read the FreeBSD Serial Hardware tutorial for a detailed understanding of serial devices, and the differences between asynchronous and synchronous serial ports. A TA running off a standard PC serial port (asynchronous) limits you to 115.2 Kbs, even though you have a 128 Kbs connection. To fully utilize the 128 Kbs that ISDN is capable of, you must move the TA to a synchronous serial card. Do not be fooled into buying an internal TA and thinking you have avoided the synchronous/asynchronous issue. Internal TA's simply have a standard PC serial port chip built into them. All this will do is save you having to buy another serial cable and find another empty electrical socket. A synchronous card with a TA is at least as fast as a stand-alone router, and with a simple 386 FreeBSD box driving it, probably more flexible. The choice of synchronous card/TA v.s. stand-alone router is largely a religious issue. There has been some discussion of this in the mailing lists. We suggest you search the archives for the complete discussion. Stand-alone ISDN Bridges/Routers ISDN stand-alone bridges/routers ISDN bridges or routers are not at all specific to FreeBSD or any other operating system. For a more complete description of routing and bridging technology, please refer to a networking reference book. In the context of this section, the terms router and bridge will be used interchangeably. As the cost of low end ISDN routers/bridges comes down, it will likely become a more and more popular choice. An ISDN router is a small box that plugs directly into your local Ethernet network, and manages its own connection to the other bridge/router. It has built in software to communicate via PPP and other popular protocols. A router will allow you much faster throughput than a standard TA, since it will be using a full synchronous ISDN connection. The main problem with ISDN routers and bridges is that interoperability between manufacturers can still be a problem. If you are planning to connect to an Internet provider, you should discuss your needs with them. If you are planning to connect two LAN segments together, such as your home LAN to the office LAN, this is the simplest lowest maintenance solution. Since you are buying the equipment for both sides of the connection you can be assured that the link will work. For example to connect a home computer or branch office network to a head office network the following setup could be used: Branch Office or Home Network 10 base 2 Network uses a bus based topology with 10 base 2 Ethernet (thinnet). Connect router to network cable with AUI/10BT transceiver, if necessary. ---Sun workstation | ---FreeBSD box | ---Windows 95 | Stand-alone router | ISDN BRI line 10 Base 2 Ethernet If your home/branch office is only one computer you can use a twisted pair crossover cable to connect to the stand-alone router directly. Head Office or Other LAN 10 base T Network uses a star topology with 10 base T Ethernet (Twisted Pair). -------Novell Server | H | | ---Sun | | | U ---FreeBSD | | | ---Windows 95 | B | |___---Stand-alone router | ISDN BRI line ISDN Network Diagram One large advantage of most routers/bridges is that they allow you to have 2 separate independent PPP connections to 2 separate sites at the same time. This is not supported on most TA's, except for specific (usually expensive) models that have two serial ports. Do not confuse this with channel bonding, MPP, etc. This can be a very useful feature if, for example, you have an dedicated ISDN connection at your office and would like to tap into it, but do not want to get another ISDN line at work. A router at the office location can manage a dedicated B channel connection (64 Kbps) to the Internet and use the other B channel for a separate data connection. The second B channel can be used for dial-in, dial-out or dynamically bonding (MPP, etc.) with the first B channel for more bandwidth. IPX/SPX An Ethernet bridge will also allow you to transmit more than just IP traffic. You can also send IPX/SPX or whatever other protocols you use. Chern Lee Contributed by Network Address Translation Overview natd FreeBSD's Network Address Translation daemon, commonly known as &man.natd.8; is a daemon that accepts incoming raw IP packets, changes the source to the local machine and re-injects these packets back into the outgoing IP packet stream. &man.natd.8; does this by changing the source IP address and port such that when data is received back, it is able to determine the original location of the data and forward it back to its original requester. Internet connection sharing NAT The most common use of NAT is to perform what is commonly known as Internet Connection Sharing. Setup Due to the diminishing IP space in IPv4, and the increased number of users on high-speed consumer lines such as cable or DSL, people are increasingly in need of an Internet Connection Sharing solution. The ability to connect several computers online through one connection and IP address makes &man.natd.8; a reasonable choice. Most commonly, a user has a machine connected to a cable or DSL line with one IP address and wishes to use this one connected computer to provide Internet access to several more over a LAN. To do this, the FreeBSD machine on the Internet must act as a gateway. This gateway machine must have two NICs—one for connecting to the Internet router, the other connecting to a LAN. All the machines on the LAN are connected through a hub or switch. There are many ways to get a LAN connected to the Internet through a &os; gateway. This example will only cover a gateway with at least two NICs. _______ __________ ________ | | | | | | | Hub |-----| Client B |-----| Router |----- Internet |_______| |__________| |________| | ____|_____ | | | Client A | |__________| Network Layout A setup like this is commonly used to share an Internet connection. One of the LAN machines is connected to the Internet. The rest of the machines access the Internet through that gateway machine. kernel configuration Configuration The following options must be in the kernel configuration file: options IPFIREWALL options IPDIVERT Additionally, at choice, the following may also be suitable: options IPFIREWALL_DEFAULT_TO_ACCEPT options IPFIREWALL_VERBOSE The following must be in /etc/rc.conf: gateway_enable="YES" firewall_enable="YES" firewall_type="OPEN" natd_enable="YES" natd_interface="fxp0" natd_flags="" Sets up the machine to act as a gateway. Running sysctl net.inet.ip.forwarding=1 would have the same effect. Enables the firewall rules in /etc/rc.firewall at boot. This specifies a predefined firewall ruleset that allows anything in. See /etc/rc.firewall for additional types. Indicates which interface to forward packets through (the interface connected to the Internet). Any additional configuration options passed to &man.natd.8; on boot. Having the previous options defined in /etc/rc.conf would run natd -interface fxp0 at boot. This can also be run manually. It is also possible to use a configuration file for &man.natd.8; when there are too many options to pass. In this case, the configuration file must be defined by adding the following line to /etc/rc.conf: natd_flags="-f /etc/natd.conf" The /etc/natd.conf file will contain a list of configuration options, one per line. For example the next section case would use the following file: redirect_port tcp 192.168.0.2:6667 6667 redirect_port tcp 192.168.0.3:80 80 For more information about the configuration file, consult the &man.natd.8; manual page about the option. Each machine and interface behind the LAN should be assigned IP address numbers in the private network space as defined by RFC 1918 and have a default gateway of the natd machine's internal IP address. For example, client A and B behind the LAN have IP addresses of 192.168.0.2 and 192.168.0.3, while the natd machine's LAN interface has an IP address of 192.168.0.1. Client A and B's default gateway must be set to that of the natd machine, 192.168.0.1. The natd machine's external, or Internet interface does not require any special modification for &man.natd.8; to work. Port Redirection The drawback with &man.natd.8; is that the LAN clients are not accessible from the Internet. Clients on the LAN can make outgoing connections to the world but cannot receive incoming ones. This presents a problem if trying to run Internet services on one of the LAN client machines. A simple way around this is to redirect selected Internet ports on the natd machine to a LAN client. For example, an IRC server runs on client A, and a web server runs on client B. For this to work properly, connections received on ports 6667 (IRC) and 80 (web) must be redirected to the respective machines. The must be passed to &man.natd.8; with the proper options. The syntax is as follows: -redirect_port proto targetIP:targetPORT[-targetPORT] [aliasIP:]aliasPORT[-aliasPORT] [remoteIP[:remotePORT[-remotePORT]]] In the above example, the argument should be: -redirect_port tcp 192.168.0.2:6667 6667 -redirect_port tcp 192.168.0.3:80 80 This will redirect the proper tcp ports to the LAN client machines. The argument can be used to indicate port ranges over individual ports. For example, tcp 192.168.0.2:2000-3000 2000-3000 would redirect all connections received on ports 2000 to 3000 to ports 2000 to 3000 on client A. These options can be used when directly running &man.natd.8;, placed within the natd_flags="" option in /etc/rc.conf, or passed via a configuration file. For further configuration options, consult &man.natd.8; Address Redirection address redirection Address redirection is useful if several IP addresses are available, yet they must be on one machine. With this, &man.natd.8; can assign each LAN client its own external IP address. &man.natd.8; then rewrites outgoing packets from the LAN clients with the proper external IP address and redirects all traffic incoming on that particular IP address back to the specific LAN client. This is also known as static NAT. For example, the IP addresses 128.1.1.1, 128.1.1.2, and 128.1.1.3 belong to the natd gateway machine. 128.1.1.1 can be used as the natd gateway machine's external IP address, while 128.1.1.2 and 128.1.1.3 are forwarded back to LAN clients A and B. The syntax is as follows: -redirect_address localIP publicIP localIP The internal IP address of the LAN client. publicIP The external IP address corresponding to the LAN client. In the example, this argument would read: -redirect_address 192.168.0.2 128.1.1.2 -redirect_address 192.168.0.3 128.1.1.3 Like , these arguments are also placed within the natd_flags="" option of /etc/rc.conf, or passed via a configuration file. With address redirection, there is no need for port redirection since all data received on a particular IP address is redirected. The external IP addresses on the natd machine must be active and aliased to the external interface. Look at &man.rc.conf.5; to do so. Parallel Line IP (PLIP) PLIP Parallel Line IP PLIP PLIP lets us run TCP/IP between parallel ports. It is useful on machines without network cards, or to install on laptops. In this section, we will discuss: Creating a parallel (laplink) cable. Connecting two computers with PLIP. Creating a Parallel Cable You can purchase a parallel cable at most computer supply stores. If you cannot do that, or you just want to know how it is done, the following table shows how to make one out of a normal parallel printer cable. Wiring a Parallel Cable for Networking A-name A-End B-End Descr. Post/Bit DATA0 -ERROR 2 15 15 2 Data 0/0x01 1/0x08 DATA1 +SLCT 3 13 13 3 Data 0/0x02 1/0x10 DATA2 +PE 4 12 12 4 Data 0/0x04 1/0x20 DATA3 -ACK 5 10 10 5 Strobe 0/0x08 1/0x40 DATA4 BUSY 6 11 11 6 Data 0/0x10 1/0x80 GND 18-25 18-25 GND -
Setting Up PLIP First, you have to get a laplink cable. Then, confirm that both computers have a kernel with &man.lpt.4; driver support: &prompt.root; grep lp /var/run/dmesg.boot lpt0: <Printer> on ppbus0 lpt0: Interrupt-driven port The parallel port must be an interrupt driven port, you should have lines similar to the following in your in the /boot/device.hints file: hint.ppc.0.at="isa" hint.ppc.0.irq="7" Then check if the kernel configuration file has a device plip line or if the plip.ko kernel module is loaded. In both cases the parallel networking interface should appear when you use the &man.ifconfig.8; command to display it: &prompt.root; ifconfig plip0 plip0: flags=8810<POINTOPOINT,SIMPLEX,MULTICAST> mtu 1500 Plug the laplink cable into the parallel interface on both computers. Configure the network interface parameters on both sites as root. For example, if you want to connect the host host1 with another machine host2: host1 <-----> host2 IP Address 10.0.0.1 10.0.0.2 Configure the interface on host1 by doing: &prompt.root; ifconfig plip0 10.0.0.1 10.0.0.2 Configure the interface on host2 by doing: &prompt.root; ifconfig plip0 10.0.0.2 10.0.0.1 You now should have a working connection. Please read the manual pages &man.lp.4; and &man.lpt.4; for more details. You should also add both hosts to /etc/hosts: 127.0.0.1 localhost.my.domain localhost 10.0.0.1 host1.my.domain host1 10.0.0.2 host2.my.domain To confirm the connection works, go to each host and ping the other. For example, on host1: &prompt.root; ifconfig plip0 plip0: flags=8851<UP,POINTOPOINT,RUNNING,SIMPLEX,MULTICAST> mtu 1500 inet 10.0.0.1 --> 10.0.0.2 netmask 0xff000000 &prompt.root; netstat -r Routing tables Internet: Destination Gateway Flags Refs Use Netif Expire host2 host1 UH 0 0 plip0 &prompt.root; ping -c 4 host2 PING host2 (10.0.0.2): 56 data bytes 64 bytes from 10.0.0.2: icmp_seq=0 ttl=255 time=2.774 ms 64 bytes from 10.0.0.2: icmp_seq=1 ttl=255 time=2.530 ms 64 bytes from 10.0.0.2: icmp_seq=2 ttl=255 time=2.556 ms 64 bytes from 10.0.0.2: icmp_seq=3 ttl=255 time=2.714 ms --- host2 ping statistics --- 4 packets transmitted, 4 packets received, 0% packet loss round-trip min/avg/max/stddev = 2.530/2.643/2.774/0.103 ms Aaron Kaplan Originally Written by Tom Rhodes Restructured and Added by Brad Davis Extended by IPv6 IPv6 (also known as IPng IP next generation) is the new version of the well known IP protocol (also known as IPv4). Like the other current *BSD systems, FreeBSD includes the KAME IPv6 reference implementation. So your FreeBSD system comes with all you will need to experiment with IPv6. This section focuses on getting IPv6 configured and running. In the early 1990s, people became aware of the rapidly diminishing address space of IPv4. Given the expansion rate of the Internet there were two major concerns: Running out of addresses. Today this is not so much of a concern anymore since RFC1918 private address space (10.0.0.0/8, 172.16.0.0/12, and 192.168.0.0/16) and Network Address Translation (NAT) are being employed. Router table entries were getting too large. This is still a concern today. IPv6 deals with these and many other issues: 128 bit address space. In other words theoretically there are 340,282,366,920,938,463,463,374,607,431,768,211,456 addresses available. This means there are approximately 6.67 * 10^27 IPv6 addresses per square meter on our planet. Routers will only store network aggregation addresses in their routing tables thus reducing the average space of a routing table to 8192 entries. There are also lots of other useful features of IPv6 such as: Address autoconfiguration (RFC2462) Anycast addresses (one-out-of many) Mandatory multicast addresses IPsec (IP security) Simplified header structure Mobile IP IPv6-to-IPv4 transition mechanisms For more information see: IPv6 overview at playground.sun.com KAME.net Background on IPv6 Addresses There are different types of IPv6 addresses: Unicast, Anycast and Multicast. Unicast addresses are the well known addresses. A packet sent to a unicast address arrives exactly at the interface belonging to the address. Anycast addresses are syntactically indistinguishable from unicast addresses but they address a group of interfaces. The packet destined for an anycast address will arrive at the nearest (in router metric) interface. Anycast addresses may only be used by routers. Multicast addresses identify a group of interfaces. A packet destined for a multicast address will arrive at all interfaces belonging to the multicast group. The IPv4 broadcast address (usually xxx.xxx.xxx.255) is expressed by multicast addresses in IPv6. Reserved IPv6 addresses IPv6 address Prefixlength (Bits) Description Notes :: 128 bits unspecified cf. 0.0.0.0 in IPv4 ::1 128 bits loopback address cf. 127.0.0.1 in IPv4 ::00:xx:xx:xx:xx 96 bits embedded IPv4 The lower 32 bits are the IPv4 address. Also called IPv4 compatible IPv6 address ::ff:xx:xx:xx:xx 96 bits IPv4 mapped IPv6 address The lower 32 bits are the IPv4 address. For hosts which do not support IPv6. fe80:: - feb:: 10 bits link-local cf. loopback address in IPv4 fec0:: - fef:: 10 bits site-local   ff:: 8 bits multicast   001 (base 2) 3 bits global unicast All global unicast addresses are assigned from this pool. The first 3 bits are 001.
Reading IPv6 Addresses The canonical form is represented as: x:x:x:x:x:x:x:x, each x being a 16 Bit hex value. For example FEBC:A574:382B:23C1:AA49:4592:4EFE:9982 Often an address will have long substrings of all zeros therefore one such substring per address can be abbreviated by ::. Also up to three leading 0s per hexquad can be omitted. For example fe80::1 corresponds to the canonical form fe80:0000:0000:0000:0000:0000:0000:0001. A third form is to write the last 32 Bit part in the well known (decimal) IPv4 style with dots . as separators. For example 2002::10.0.0.1 corresponds to the (hexadecimal) canonical representation 2002:0000:0000:0000:0000:0000:0a00:0001 which in turn is equivalent to writing 2002::a00:1. By now the reader should be able to understand the following: &prompt.root; ifconfig rl0: flags=8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST> mtu 1500 inet 10.0.0.10 netmask 0xffffff00 broadcast 10.0.0.255 inet6 fe80::200:21ff:fe03:8e1%rl0 prefixlen 64 scopeid 0x1 ether 00:00:21:03:08:e1 media: Ethernet autoselect (100baseTX ) status: active fe80::200:21ff:fe03:8e1%rl0 is an auto configured link-local address. It is generated from the MAC address as part of the auto configuration. For further information on the structure of IPv6 addresses see RFC3513. Getting Connected Currently there are four ways to connect to other IPv6 hosts and networks: Contact your Internet Service Provider to see if they offer IPv6 yet. SixXS offers tunnels with end-points all around the globe. Tunnel via 6-to-4 (RFC3068) Use the net/freenet6 port if you are on a dial-up connection. DNS in the IPv6 World There used to be two types of DNS records for IPv6. The IETF has declared A6 records obsolete. AAAA records are the standard now. Using AAAA records is straightforward. Assign your hostname to the new IPv6 address you just received by adding: MYHOSTNAME AAAA MYIPv6ADDR To your primary zone DNS file. In case you do not serve your own DNS zones ask your DNS provider. Current versions of bind (version 8.3 and 9) and dns/djbdns (with the IPv6 patch) support AAAA records. Applying the needed changes to <filename>/etc/rc.conf</filename> IPv6 Client Settings These settings will help you configure a machine that will be on your LAN and act as a client, not a router. To have &man.rtsol.8; autoconfigure your interface on boot all you need to add is: ipv6_enable="YES" To statically assign an IP address such as 2001:471:1f11:251:290:27ff:fee0:2093, to your fxp0 interface, add: ipv6_ifconfig_fxp0="2001:471:1f11:251:290:27ff:fee0:2093" To assign a default router of 2001:471:1f11:251::1 add the following to /etc/rc.conf: ipv6_defaultrouter="2001:471:1f11:251::1" IPv6 Router/Gateway Settings This will help you take the directions that your tunnel provider has given you and convert it into settings that will persist through reboots. To restore your tunnel on startup use something like the following in /etc/rc.conf: List the Generic Tunneling interfaces that will be configured, for example gif0: gif_interfaces="gif0" To configure the interface with a local endpoint of MY_IPv4_ADDR to a remote endpoint of REMOTE_IPv4_ADDR: gifconfig_gif0="MY_IPv4_ADDR REMOTE_IPv4_ADDR" To apply the IPv6 address you have been assigned for use as your IPv6 tunnel endpoint, add: ipv6_ifconfig_gif0="MY_ASSIGNED_IPv6_TUNNEL_ENDPOINT_ADDR" Then all you have to do is set the default route for IPv6. This is the other side of the IPv6 tunnel: ipv6_defaultrouter="MY_IPv6_REMOTE_TUNNEL_ENDPOINT_ADDR" IPv6 Tunnel Settings If the server is to route IPv6 between the rest of your network and the world, the following /etc/rc.conf setting will also be needed: ipv6_gateway_enable="YES" Router Advertisement and Host Auto Configuration This section will help you setup &man.rtadvd.8; to advertise the IPv6 default route. To enable &man.rtadvd.8; you will need the following in your /etc/rc.conf: rtadvd_enable="YES" It is important that you specify the interface on which to do IPv6 router solicitation. For example to tell &man.rtadvd.8; to use fxp0: rtadvd_interfaces="fxp0" Now we must create the configuration file, /etc/rtadvd.conf. Here is an example: fxp0:\ :addrs#1:addr="2001:471:1f11:246::":prefixlen#64:tc=ether: Replace fxp0 with the interface you are going to be using. Next, replace 2001:471:1f11:246:: with the prefix of your allocation. If you are dedicated a /64 subnet you will not need to change anything else. Otherwise, you will need to change the prefixlen# to the correct value. Harti Brandt Contributed by Asynchronous Transfer Mode (ATM) Configuring classical IP over ATM (PVCs) Classical IP over ATM (CLIP) is the simplest method to use Asynchronous Transfer Mode (ATM) with IP. It can be used with switched connections (SVCs) and with permanent connections (PVCs). This section describes how to set up a network based on PVCs. Fully meshed configurations The first method to set up a CLIP with PVCs is to connect each machine to each other machine in the network via a dedicated PVC. While this is simple to configure it tends to become impractical for a larger number of machines. The example supposes that we have four machines in the network, each connected to the ATM network with an ATM adapter card. The first step is the planning of the IP addresses and the ATM connections between the machines. We use the following: Host IP Address hostA 192.168.173.1 hostB 192.168.173.2 hostC 192.168.173.3 hostD 192.168.173.4 To build a fully meshed net we need one ATM connection between each pair of machines: Machines VPI.VCI couple hostA - hostB 0.100 hostA - hostC 0.101 hostA - hostD 0.102 hostB - hostC 0.103 hostB - hostD 0.104 hostC - hostD 0.105 The VPI and VCI values at each end of the connection may of course differ, but for simplicity we assume that they are the same. Next we need to configure the ATM interfaces on each host: hostA&prompt.root; ifconfig hatm0 192.168.173.1 up hostB&prompt.root; ifconfig hatm0 192.168.173.2 up hostC&prompt.root; ifconfig hatm0 192.168.173.3 up hostD&prompt.root; ifconfig hatm0 192.168.173.4 up assuming that the ATM interface is hatm0 on all hosts. Now the PVCs need to be configured on hostA (we assume that they are already configured on the ATM switches, you need to consult the manual for the switch on how to do this). hostA&prompt.root; atmconfig natm add 192.168.173.2 hatm0 0 100 llc/snap ubr hostA&prompt.root; atmconfig natm add 192.168.173.3 hatm0 0 101 llc/snap ubr hostA&prompt.root; atmconfig natm add 192.168.173.4 hatm0 0 102 llc/snap ubr hostB&prompt.root; atmconfig natm add 192.168.173.1 hatm0 0 100 llc/snap ubr hostB&prompt.root; atmconfig natm add 192.168.173.3 hatm0 0 103 llc/snap ubr hostB&prompt.root; atmconfig natm add 192.168.173.4 hatm0 0 104 llc/snap ubr hostC&prompt.root; atmconfig natm add 192.168.173.1 hatm0 0 101 llc/snap ubr hostC&prompt.root; atmconfig natm add 192.168.173.2 hatm0 0 103 llc/snap ubr hostC&prompt.root; atmconfig natm add 192.168.173.4 hatm0 0 105 llc/snap ubr hostD&prompt.root; atmconfig natm add 192.168.173.1 hatm0 0 102 llc/snap ubr hostD&prompt.root; atmconfig natm add 192.168.173.2 hatm0 0 104 llc/snap ubr hostD&prompt.root; atmconfig natm add 192.168.173.3 hatm0 0 105 llc/snap ubr Of course other traffic contracts than UBR can be used given the ATM adapter supports those. In this case the name of the traffic contract is followed by the parameters of the traffic. Help for the &man.atmconfig.8; tool can be obtained with: &prompt.root; atmconfig help natm add or in the &man.atmconfig.8; manual page. The same configuration can also be done via /etc/rc.conf. For hostA this would look like: network_interfaces="lo0 hatm0" ifconfig_hatm0="inet 192.168.173.1 up" natm_static_routes="hostB hostC hostD" route_hostB="192.168.173.2 hatm0 0 100 llc/snap ubr" route_hostC="192.168.173.3 hatm0 0 101 llc/snap ubr" route_hostD="192.168.173.4 hatm0 0 102 llc/snap ubr" The current state of all CLIP routes can be obtained with: hostA&prompt.root; atmconfig natm show Tom Rhodes Contributed by Common Access Redundancy Protocol (CARP) CARP Common Access Redundancy Protocol The Common Access Redundancy Protocol, or CARP allows multiple hosts to share the same IP address. In some configurations, this may be used for availability or load balancing. Hosts may use separate IP addresses as well, as in the example provided here. To enable support for CARP, the &os; kernel must be rebuilt with the following option: device carp CARP functionality should now be available and may be tuned via several sysctl OIDs: OID Description net.inet.carp.allow Accept incoming CARP packets. Enabled by default. net.inet.carp.preempt This option downs all of the CARP interfaces on the host when one of them goes down. Disabled by default net.inet.carp.log A value of 0 disables any logging. A Value of 1 enables logging of bad CARP packets. Values greater than 1 enables logging of state changes for the CARP interfaces. The default value is 1. net.inet.carp.arpbalance Balance local network traffic using ARP. Disabled by default. net.inet.carp.suppress_preempt A read only OID showing the status of preemption suppression. Preemption can be suppressed if link on an interface is down. A value of 0, means that preemption is not suppressed. Every problem increments this OID. The CARP devices themselves may be created via the ifconfig command: &prompt.root; ifconfig carp0 create In a real environment, these interfaces will need unique identification numbers known as a VHID. This VHID or Virtual Host Identification will be used to distinguish the host on the network. Using CARP For Server Availability (CARP) One use of CARP, as noted above, is for server availability. This example will provide failover support for three hosts, all with unique IP addresses and providing the same web content. These machines will act in conjunction with a Round Robin DNS configuration. The failover machine will have two additional CARP interfaces, one for each of the content server's IPs. When a failure occurs, the failover server should pick up the failed machine's IP address. This means the failure should go completely unnoticed to the user. The failover server requires identical content and services as the other content servers it is expected to pick up load for. The two machines should be configured identically other than their issued hostnames and VHIDs. This example calls these machines hosta.example.org and hostb.example.org respectively. First, the required lines for a CARP configuration have to be added to rc.conf. For hosta.example.org, the rc.conf file should contain the following lines: hostname="hosta.example.org" ifconfig_fxp0="inet 192.168.1.3 netmask 255.255.255.0" cloned_interfaces="carp0" ifconfig_carp0="vhid 1 pass testpass 192.168.1.50/24" On hostb.example.org the following lines should be in rc.conf: hostname="hostb.example.org" ifconfig_fxp0="inet 192.168.1.4 netmask 255.255.255.0" cloned_interfaces="carp0" ifconfig_carp0="vhid 2 pass testpass 192.168.1.51/24" It is very important that the passwords, specified by the option to ifconfig, are identical. The carp devices will only listen to and accept advertisements from machines with the correct password. The VHID must also be different for each machine. The third machine, provider.example.org, should be prepared so that it may handle failover from either host. This machine will require two carp devices, one to handle each host. The appropriate rc.conf configuration lines will be similar to the following: hostname="provider.example.org" ifconfig_fxp0="inet 192.168.1.5 netmask 255.255.255.0" cloned_interfaces="carp0 carp1" ifconfig_carp0="vhid 1 advskew 100 pass testpass 192.168.1.50/24" ifconfig_carp1="vhid 2 advskew 100 pass testpass 192.168.1.51/24" Having the two carp devices will allow provider.example.org to notice and pick up the IP address of either machine should it stop responding. The default &os; kernel may have preemption enabled. If so, provider.example.org may not relinquish the IP address back to the original content server. In this case, an administrator may have to manually force the IP back to the master. The following command should be issued on provider.example.org: &prompt.root; ifconfig carp0 down && ifconfig carp0 up This should be done on the carp interface which corresponds to the correct host. At this point, CARP should be completely enabled and available for testing. For testing, either networking has to be restarted or the machines need to be rebooted. More information is always available in the &man.carp.4; manual page.