Index: sbin/ifconfig/sfp.c
===================================================================
--- sbin/ifconfig/sfp.c
+++ sbin/ifconfig/sfp.c
@@ -171,7 +171,7 @@
 
 /* 10/40G Ethernet compliance codes, byte 128 + 3 */
 static struct _nv eth_1040g[] = {
-	{ 0x80, "Reserved" },
+	{ 0x80, "Extended" },
 	{ 0x40, "10GBASE-LRM" },
 	{ 0x20, "10GBASE-LR" },
 	{ 0x10, "10GBASE-SR" },
@@ -182,6 +182,37 @@
 	{ 0, NULL }
 };
 
+/* SFF-8024 Rev. 3.4 table 4.4: Extended Specification Compliance */
+static struct _nv eth_extended_comp[] = {
+	{ 0xFF, "Reserved" },
+	{ 0x1A, "2 lambda DWDM 100G" },
+	{ 0x19, "100G ACC or 25GAUI C2M ACC" },
+	{ 0x18, "100G AOC or 25GAUI C2M AOC" },
+	{ 0x17, "100G CLR4" },
+	{ 0x16, "10GBASE-T with SFI electrical interface" },
+	{ 0x15, "G959.1 profile P1L1-2D2" },
+	{ 0x14, "G959.1 profile P1S1-2D2" },
+	{ 0x13, "G959.1 profile P1I1-2D1" },
+	{ 0x12, "40G PSM4 Parallel SMF" },
+	{ 0x11, "4 x 10GBASE-SR" },
+	{ 0x10, "40GBASE-ER4" },
+	{ 0x0F, "Reserved" },
+	{ 0x0D, "25GBASE-CR CA-N" },
+	{ 0x0C, "25GBASE-CR CA-S" },
+	{ 0x0B, "100GBASE-CR4 or 25GBASE-CR CA-L" },
+	{ 0x0A, "Reserved" },
+	{ 0x09, "100G CWDM4 MSA without FEC" },
+	{ 0x08, "100G ACC (Active Copper Cable)" },
+	{ 0x07, "100G PSM4 Parallel SMF" },
+	{ 0x06, "100G CWDM4 MSA with FEC" },
+	{ 0x05, "100GBASE-SR10" },
+	{ 0x04, "100GBASE-ER4" },
+	{ 0x03, "100GBASE-LR4" },
+	{ 0x02, "100GBASE-SR4" },
+	{ 0x01, "100G AOC (Active Optical Cable) or 25GAUI C2M ACC" },
+	{ 0x00, "Unspecified" }
+};
+
 /* SFF-8636 Rev. 2.5 table 6.3: Revision compliance */
 static struct _nv rev_compl[] = {
 	{ 0x1, "SFF-8436 rev <=4.8" },
@@ -371,9 +402,16 @@
 	const char *tech_class;
 	uint8_t code;
 
-	/* Check 10/40G Ethernet class only */
 	read_i2c(ii, SFF_8436_BASE, SFF_8436_CODE_E1040G, 1, &code);
-	tech_class = find_zero_bit(eth_1040g, code, 1);
+
+	/* Check for extended specification compliance */
+	if (code & 0x80) {
+		read_i2c(ii, SFF_8436_BASE, SFF_8436_OPTIONS_START, 1, &code);
+		tech_class = find_value(eth_extended_comp, code);
+	} else
+		/* Check 10/40G Ethernet class only */
+		tech_class = find_zero_bit(eth_1040g, code, 1);
+
 	if (tech_class == NULL)
 		tech_class = "Unknown";
 
@@ -873,6 +911,7 @@
 	switch (id_byte) {
 	case SFF_8024_ID_QSFP:
 	case SFF_8024_ID_QSFPPLUS:
+	case SFF_8024_ID_QSFP28:
 		print_qsfp_status(&ii, verbose);
 		break;
 	default: