Index: libexec/rc/rc.conf
===================================================================
--- libexec/rc/rc.conf
+++ libexec/rc/rc.conf
@@ -712,8 +712,12 @@
 devfs_load_rulesets="YES"	# Enable to always load the default rulesets
 performance_cx_lowest="NONE"	# Online CPU idle state
 performance_cpu_freq="NONE"	# Online CPU frequency
+performance_tz0_active="NONE"	# Online forced active cooling zone
+performance_tz0_PSV="NONE"	# Online passive cooling threshold
 economy_cx_lowest="Cmax"	# Offline CPU idle state
 economy_cpu_freq="NONE"		# Offline CPU frequency
+economy_tz0_active="NONE"	# Offline forced active cooling zone
+economy_tz0_PSV="NONE"		# Offline passive cooling threshold
 virecover_enable="YES"	# Perform housekeeping for the vi(1) editor
 ugidfw_enable="NO"	# Load mac_bsdextended(4) rules on boot
 bsdextended_script="/etc/rc.bsdextended"	# Default mac_bsdextended(4)
Index: libexec/rc/rc.d/power_profile
===================================================================
--- libexec/rc/rc.d/power_profile
+++ libexec/rc/rc.d/power_profile
@@ -80,6 +80,14 @@
 esac
 
 # Set the various sysctls based on the profile's values.
+node="hw.acpi.thermal.tz0._PSV"
+eval value=\$${profile}_tz0_PSV
+sysctl_set
+
+node="hw.acpi.thermal.tz0.active"
+eval value=\$${profile}_tz0_active
+sysctl_set
+
 node="hw.acpi.cpu.cx_lowest"
 highest_value="C1"
 lowest_value="Cmax"
Index: sys/dev/acpica/acpi_thermal.c
===================================================================
--- sys/dev/acpica/acpi_thermal.c
+++ sys/dev/acpica/acpi_thermal.c
@@ -605,7 +605,7 @@
     /* XXX (de)activate any passive cooling that may be required. */
 
     /*
-     * If the temperature is at _HOT or _CRT, increment our event count.
+     * If the temperature is at _CR3, _HOT or _CRT, increment our event count.
      * If it has occurred enough times, shutdown the system.  This is
      * needed because some systems will report an invalid high temperature
      * for one poll cycle.  It is suspected this is due to the embedded
@@ -1023,51 +1023,68 @@
 static int
 acpi_tz_cpufreq_restore(struct acpi_tz_softc *sc)
 {
-    device_t dev;
-    int error;
+    device_t *devs;
+    int devcount, error, n;
 
     if (!sc->tz_cooling_updated)
 	return (0);
-    if ((dev = devclass_get_device(devclass_find("cpufreq"), 0)) == NULL)
+
+    if ((error = devclass_get_devices(devclass_find("cpufreq"), &devs, &devcount))) {
+	free(devs, M_TEMP);
 	return (ENXIO);
+    }
+
     ACPI_VPRINT(sc->tz_dev, acpi_device_get_parent_softc(sc->tz_dev),
 	"temperature %d.%dC: resuming previous clock speed (%d MHz)\n",
 	TZ_KELVTOC(sc->tz_temperature), sc->tz_cooling_saved_freq);
-    error = CPUFREQ_SET(dev, NULL, CPUFREQ_PRIO_KERN);
+    for (n = 0; n < devcount; n++) {
+	if ((error = CPUFREQ_SET(devs[n], NULL, CPUFREQ_PRIO_KERN))) {
+	    /*
+	     * If you find yourself here:  cf_set_method() in kern_cpu.c
+	     * requires CPUFREQ_GET() be run before CPUFREQ_SET(), otherwise on
+	     * a restore sc->curr_level.total_set.freq = CPUFREQ_VAL_UNKNOWN,
+	     * and then if it hasn't been updated the next save/restore will fail.
+	     */
+	    device_printf(sc->tz_dev, "cpu%d: failed to restore cpufreq priority\n", n);
+	    break;
+	}
+    }
     if (error == 0)
 	sc->tz_cooling_updated = FALSE;
+
+    free(devs, M_TEMP);
     return (error);
 }
 
 static int
 acpi_tz_cpufreq_update(struct acpi_tz_softc *sc, int req)
 {
-    device_t dev;
+    device_t *devs;
     struct cf_level *levels;
-    int num_levels, error, freq, desired_freq, perf, i;
+    int num_levels, error, freq, desired_freq, perf, devcount, i, n;
 
     levels = malloc(CPUFREQ_MAX_LEVELS * sizeof(*levels), M_TEMP, M_NOWAIT);
     if (levels == NULL)
 	return (ENOMEM);
 
     /*
-     * Find the main device, cpufreq0.  We don't yet support independent
-     * CPU frequency control on SMP.
+     * Find the main device, cpufreq0.  We make plans based upon cpu0, and
+     * change all the cpu frequencies to the same level.
      */
-    if ((dev = devclass_get_device(devclass_find("cpufreq"), 0)) == NULL) {
-	error = ENXIO;
+    if ((error = devclass_get_devices(devclass_find("cpufreq"), &devs, &devcount))) {
+	free(devs, M_TEMP);
 	goto out;
     }
 
-    /* Get the current frequency. */
-    error = CPUFREQ_GET(dev, &levels[0]);
+    /* Get the current frequency for cpu0. */
+    error = CPUFREQ_GET(devs[0], &levels[0]);
     if (error)
 	goto out;
     freq = levels[0].total_set.freq;
 
-    /* Get the current available frequency levels. */
+    /* Get the current available frequency levels for cpu0. */
     num_levels = CPUFREQ_MAX_LEVELS;
-    error = CPUFREQ_LEVELS(dev, levels, &num_levels);
+    error = CPUFREQ_LEVELS(devs[0], levels, &num_levels);
     if (error) {
 	if (error == E2BIG)
 	    printf("cpufreq: need to increase CPUFREQ_MAX_LEVELS\n");
@@ -1128,8 +1145,22 @@
 	    TZ_KELVTOC(sc->tz_temperature),
 	    (freq > levels[i].total_set.freq) ? "de" : "in",
 	    freq, levels[i].total_set.freq);
-	error = CPUFREQ_SET(dev, &levels[i], CPUFREQ_PRIO_KERN);
-	if (error == 0 && !sc->tz_cooling_updated) {
+
+	/* Change all the cpus to the chosen frequency. */
+	for (n = 0; n < devcount; n++) {
+	    /* CPUFREQ_SET() fails occasionally without this. */
+	    if ((error = CPUFREQ_GET(devs[n], &levels[0])))
+		goto out;
+
+	    if ((error = CPUFREQ_LEVELS(devs[n], levels, &num_levels))) {
+		if (error == E2BIG)
+		    printf("cpufreq: need to increase CPUFREQ_MAX_LEVELS\n");
+		goto out;
+	    }
+	    if ((error = CPUFREQ_SET(devs[n], &levels[i], CPUFREQ_PRIO_KERN)))
+		goto out;
+	}
+	if (!sc->tz_cooling_updated) {
 	    sc->tz_cooling_saved_freq = freq;
 	    sc->tz_cooling_updated = TRUE;
 	}
@@ -1138,6 +1169,7 @@
 out:
     if (levels)
 	free(levels, M_TEMP);
+    free(devs, M_TEMP);
     return (error);
 }