Index: sys/dev/e1000/e1000_80003es2lan.c =================================================================== --- sys/dev/e1000/e1000_80003es2lan.c +++ sys/dev/e1000/e1000_80003es2lan.c @@ -851,11 +851,17 @@ e1000_release_phy_80003es2lan(hw); /* Disable IBIST slave mode (far-end loopback) */ - e1000_read_kmrn_reg_80003es2lan(hw, E1000_KMRNCTRLSTA_INBAND_PARAM, - &kum_reg_data); - kum_reg_data |= E1000_KMRNCTRLSTA_IBIST_DISABLE; - e1000_write_kmrn_reg_80003es2lan(hw, E1000_KMRNCTRLSTA_INBAND_PARAM, - kum_reg_data); + ret_val = e1000_read_kmrn_reg_80003es2lan(hw, + E1000_KMRNCTRLSTA_INBAND_PARAM, &kum_reg_data); + if (!ret_val) { + kum_reg_data |= E1000_KMRNCTRLSTA_IBIST_DISABLE; + ret_val = e1000_write_kmrn_reg_80003es2lan(hw, + E1000_KMRNCTRLSTA_INBAND_PARAM, + kum_reg_data); + if (ret_val) + DEBUGOUT("Error disabling far-end loopback\n"); + } else + DEBUGOUT("Error disabling far-end loopback\n"); ret_val = e1000_get_auto_rd_done_generic(hw); if (ret_val) @@ -911,11 +917,18 @@ return ret_val; /* Disable IBIST slave mode (far-end loopback) */ - e1000_read_kmrn_reg_80003es2lan(hw, E1000_KMRNCTRLSTA_INBAND_PARAM, - &kum_reg_data); - kum_reg_data |= E1000_KMRNCTRLSTA_IBIST_DISABLE; - e1000_write_kmrn_reg_80003es2lan(hw, E1000_KMRNCTRLSTA_INBAND_PARAM, - kum_reg_data); + ret_val = + e1000_read_kmrn_reg_80003es2lan(hw, E1000_KMRNCTRLSTA_INBAND_PARAM, + &kum_reg_data); + if (!ret_val) { + kum_reg_data |= E1000_KMRNCTRLSTA_IBIST_DISABLE; + ret_val = e1000_write_kmrn_reg_80003es2lan(hw, + E1000_KMRNCTRLSTA_INBAND_PARAM, + kum_reg_data); + if (ret_val) + DEBUGOUT("Error disabling far-end loopback\n"); + } else + DEBUGOUT("Error disabling far-end loopback\n"); /* Set the transmit descriptor write-back policy */ reg_data = E1000_READ_REG(hw, E1000_TXDCTL(0)); Index: sys/dev/e1000/e1000_82540.c =================================================================== --- sys/dev/e1000/e1000_82540.c +++ sys/dev/e1000/e1000_82540.c @@ -66,7 +66,7 @@ static s32 e1000_init_phy_params_82540(struct e1000_hw *hw) { struct e1000_phy_info *phy = &hw->phy; - s32 ret_val = E1000_SUCCESS; + s32 ret_val; phy->addr = 1; phy->autoneg_mask = AUTONEG_ADVERTISE_SPEED_DEFAULT; @@ -329,7 +329,7 @@ { struct e1000_mac_info *mac = &hw->mac; u32 txdctl, ctrl_ext; - s32 ret_val = E1000_SUCCESS; + s32 ret_val; u16 i; DEBUGFUNC("e1000_init_hw_82540"); @@ -411,7 +411,7 @@ static s32 e1000_setup_copper_link_82540(struct e1000_hw *hw) { u32 ctrl; - s32 ret_val = E1000_SUCCESS; + s32 ret_val; u16 data; DEBUGFUNC("e1000_setup_copper_link_82540"); @@ -498,7 +498,7 @@ **/ static s32 e1000_adjust_serdes_amplitude_82540(struct e1000_hw *hw) { - s32 ret_val = E1000_SUCCESS; + s32 ret_val; u16 nvm_data; DEBUGFUNC("e1000_adjust_serdes_amplitude_82540"); @@ -528,7 +528,7 @@ **/ static s32 e1000_set_vco_speed_82540(struct e1000_hw *hw) { - s32 ret_val = E1000_SUCCESS; + s32 ret_val; u16 default_page = 0; u16 phy_data; Index: sys/dev/e1000/e1000_82541.c =================================================================== --- sys/dev/e1000/e1000_82541.c +++ sys/dev/e1000/e1000_82541.c @@ -85,7 +85,7 @@ static s32 e1000_init_phy_params_82541(struct e1000_hw *hw) { struct e1000_phy_info *phy = &hw->phy; - s32 ret_val = E1000_SUCCESS; + s32 ret_val; DEBUGFUNC("e1000_init_phy_params_82541"); @@ -295,7 +295,7 @@ **/ static s32 e1000_reset_hw_82541(struct e1000_hw *hw) { - u32 ledctl, ctrl, icr, manc; + u32 ledctl, ctrl, manc; DEBUGFUNC("e1000_reset_hw_82541"); @@ -317,6 +317,7 @@ /* Must reset the Phy before resetting the MAC */ if ((hw->mac.type == e1000_82541) || (hw->mac.type == e1000_82547)) { E1000_WRITE_REG(hw, E1000_CTRL, (ctrl | E1000_CTRL_PHY_RST)); + E1000_WRITE_FLUSH(hw); msec_delay(5); } @@ -359,7 +360,7 @@ E1000_WRITE_REG(hw, E1000_IMC, 0xFFFFFFFF); /* Clear any pending interrupt events. */ - icr = E1000_READ_REG(hw, E1000_ICR); + E1000_READ_REG(hw, E1000_ICR); return E1000_SUCCESS; } Index: sys/dev/e1000/e1000_82542.c =================================================================== --- sys/dev/e1000/e1000_82542.c +++ sys/dev/e1000/e1000_82542.c @@ -317,7 +317,7 @@ static s32 e1000_setup_link_82542(struct e1000_hw *hw) { struct e1000_mac_info *mac = &hw->mac; - s32 ret_val = E1000_SUCCESS; + s32 ret_val; DEBUGFUNC("e1000_setup_link_82542"); @@ -565,7 +565,7 @@ * * Reads the device MAC address from the EEPROM and stores the value. **/ -static s32 e1000_read_mac_addr_82542(struct e1000_hw *hw) +s32 e1000_read_mac_addr_82542(struct e1000_hw *hw) { s32 ret_val = E1000_SUCCESS; u16 offset, nvm_data, i; Index: sys/dev/e1000/e1000_82543.c =================================================================== --- sys/dev/e1000/e1000_82543.c +++ sys/dev/e1000/e1000_82543.c @@ -900,7 +900,7 @@ **/ static s32 e1000_reset_hw_82543(struct e1000_hw *hw) { - u32 ctrl, icr; + u32 ctrl; s32 ret_val = E1000_SUCCESS; DEBUGFUNC("e1000_reset_hw_82543"); @@ -942,7 +942,7 @@ /* Masking off and clearing any pending interrupts */ E1000_WRITE_REG(hw, E1000_IMC, 0xffffffff); - icr = E1000_READ_REG(hw, E1000_ICR); + E1000_READ_REG(hw, E1000_ICR); return ret_val; } Index: sys/dev/e1000/e1000_82571.h =================================================================== --- sys/dev/e1000/e1000_82571.h +++ sys/dev/e1000/e1000_82571.h @@ -50,9 +50,10 @@ #define E1000_EIAC_82574 0x000DC /* Ext. Interrupt Auto Clear - RW */ #define E1000_EIAC_MASK_82574 0x01F00000 -#define E1000_NVM_INIT_CTRL2_MNGM 0x6000 /* Manageability Operation Mode mask */ +#define E1000_IVAR_INT_ALLOC_VALID 0x8 -#define E1000_RXCFGL 0x0B634 /* TimeSync Rx EtherType & Msg Type Reg - RW */ +/* Manageability Operation Mode mask */ +#define E1000_NVM_INIT_CTRL2_MNGM 0x6000 #define E1000_BASE1000T_STATUS 10 #define E1000_IDLE_ERROR_COUNT_MASK 0xFF Index: sys/dev/e1000/e1000_82575.h =================================================================== --- sys/dev/e1000/e1000_82575.h +++ sys/dev/e1000/e1000_82575.h @@ -495,8 +495,8 @@ s32 e1000_promisc_set_vf(struct e1000_hw *, enum e1000_promisc_type type); u16 e1000_rxpbs_adjust_82580(u32 data); s32 e1000_read_emi_reg(struct e1000_hw *hw, u16 addr, u16 *data); -s32 e1000_set_eee_i350(struct e1000_hw *); -s32 e1000_set_eee_i354(struct e1000_hw *); +s32 e1000_set_eee_i350(struct e1000_hw *hw, bool adv1G, bool adv100M); +s32 e1000_set_eee_i354(struct e1000_hw *hw, bool adv1G, bool adv100M); s32 e1000_get_eee_status_i354(struct e1000_hw *, bool *); s32 e1000_initialize_M88E1512_phy(struct e1000_hw *hw); Index: sys/dev/e1000/e1000_82575.c =================================================================== --- sys/dev/e1000/e1000_82575.c +++ sys/dev/e1000/e1000_82575.c @@ -1235,7 +1235,7 @@ DEBUGFUNC("e1000_check_for_link_media_swap"); - /* Check the copper medium. */ + /* Check for copper. */ ret_val = phy->ops.write_reg(hw, E1000_M88E1112_PAGE_ADDR, 0); if (ret_val) return ret_val; @@ -1247,7 +1247,7 @@ if (data & E1000_M88E1112_STATUS_LINK) port = E1000_MEDIA_PORT_COPPER; - /* Check the other medium. */ + /* Check for other. */ ret_val = phy->ops.write_reg(hw, E1000_M88E1112_PAGE_ADDR, 1); if (ret_val) return ret_val; @@ -1256,11 +1256,6 @@ if (ret_val) return ret_val; - /* reset page to 0 */ - ret_val = phy->ops.write_reg(hw, E1000_M88E1112_PAGE_ADDR, 0); - if (ret_val) - return ret_val; - if (data & E1000_M88E1112_STATUS_LINK) port = E1000_MEDIA_PORT_OTHER; @@ -1268,8 +1263,20 @@ if (port && (hw->dev_spec._82575.media_port != port)) { hw->dev_spec._82575.media_port = port; hw->dev_spec._82575.media_changed = TRUE; + } + + if (port == E1000_MEDIA_PORT_COPPER) { + /* reset page to 0 */ + ret_val = phy->ops.write_reg(hw, E1000_M88E1112_PAGE_ADDR, 0); + if (ret_val) + return ret_val; + e1000_check_for_link_82575(hw); } else { - ret_val = e1000_check_for_link_82575(hw); + e1000_check_for_link_82575(hw); + /* reset page to 0 */ + ret_val = phy->ops.write_reg(hw, E1000_M88E1112_PAGE_ADDR, 0); + if (ret_val) + return ret_val; } return E1000_SUCCESS; @@ -2136,7 +2143,13 @@ u32 rctl, rlpml, rxdctl[4], rfctl, temp_rctl, rx_enabled; int i, ms_wait; - DEBUGFUNC("e1000_rx_fifo_workaround_82575"); + DEBUGFUNC("e1000_rx_fifo_flush_82575"); + + /* disable IPv6 options as per hardware errata */ + rfctl = E1000_READ_REG(hw, E1000_RFCTL); + rfctl |= E1000_RFCTL_IPV6_EX_DIS; + E1000_WRITE_REG(hw, E1000_RFCTL, rfctl); + if (hw->mac.type != e1000_82575 || !(E1000_READ_REG(hw, E1000_MANC) & E1000_MANC_RCV_TCO_EN)) return; @@ -2164,7 +2177,6 @@ * incoming packets are rejected. Set enable and wait 2ms so that * any packet that was coming in as RCTL.EN was set is flushed */ - rfctl = E1000_READ_REG(hw, E1000_RFCTL); E1000_WRITE_REG(hw, E1000_RFCTL, rfctl & ~E1000_RFCTL_LEF); rlpml = E1000_READ_REG(hw, E1000_RLPML); @@ -2894,11 +2906,13 @@ /** * e1000_set_eee_i350 - Enable/disable EEE support * @hw: pointer to the HW structure + * @adv1g: boolean flag enabling 1G EEE advertisement + * @adv100m: boolean flag enabling 100M EEE advertisement * * Enable/disable EEE based on setting in dev_spec structure. * **/ -s32 e1000_set_eee_i350(struct e1000_hw *hw) +s32 e1000_set_eee_i350(struct e1000_hw *hw, bool adv1G, bool adv100M) { u32 ipcnfg, eeer; @@ -2914,7 +2928,16 @@ if (!(hw->dev_spec._82575.eee_disable)) { u32 eee_su = E1000_READ_REG(hw, E1000_EEE_SU); - ipcnfg |= (E1000_IPCNFG_EEE_1G_AN | E1000_IPCNFG_EEE_100M_AN); + if (adv100M) + ipcnfg |= E1000_IPCNFG_EEE_100M_AN; + else + ipcnfg &= ~E1000_IPCNFG_EEE_100M_AN; + + if (adv1G) + ipcnfg |= E1000_IPCNFG_EEE_1G_AN; + else + ipcnfg &= ~E1000_IPCNFG_EEE_1G_AN; + eeer |= (E1000_EEER_TX_LPI_EN | E1000_EEER_RX_LPI_EN | E1000_EEER_LPI_FC); @@ -2938,11 +2961,13 @@ /** * e1000_set_eee_i354 - Enable/disable EEE support * @hw: pointer to the HW structure + * @adv1g: boolean flag enabling 1G EEE advertisement + * @adv100m: boolean flag enabling 100M EEE advertisement * * Enable/disable EEE legacy mode based on setting in dev_spec structure. * **/ -s32 e1000_set_eee_i354(struct e1000_hw *hw) +s32 e1000_set_eee_i354(struct e1000_hw *hw, bool adv1G, bool adv100M) { struct e1000_phy_info *phy = &hw->phy; s32 ret_val = E1000_SUCCESS; @@ -2984,8 +3009,16 @@ if (ret_val) goto out; - phy_data |= E1000_EEE_ADV_100_SUPPORTED | - E1000_EEE_ADV_1000_SUPPORTED; + if (adv100M) + phy_data |= E1000_EEE_ADV_100_SUPPORTED; + else + phy_data &= ~E1000_EEE_ADV_100_SUPPORTED; + + if (adv1G) + phy_data |= E1000_EEE_ADV_1000_SUPPORTED; + else + phy_data &= ~E1000_EEE_ADV_1000_SUPPORTED; + ret_val = e1000_write_xmdio_reg(hw, E1000_EEE_ADV_ADDR_I354, E1000_EEE_ADV_DEV_I354, phy_data); Index: sys/dev/e1000/e1000_api.h =================================================================== --- sys/dev/e1000/e1000_api.h +++ sys/dev/e1000/e1000_api.h @@ -97,6 +97,7 @@ void e1000_power_up_phy(struct e1000_hw *hw); void e1000_power_down_phy(struct e1000_hw *hw); s32 e1000_read_mac_addr(struct e1000_hw *hw); +s32 e1000_read_pba_num(struct e1000_hw *hw, u32 *part_num); s32 e1000_read_pba_string(struct e1000_hw *hw, u8 *pba_num, u32 pba_num_size); s32 e1000_read_pba_length(struct e1000_hw *hw, u32 *pba_num_size); void e1000_reload_nvm(struct e1000_hw *hw); Index: sys/dev/e1000/e1000_api.c =================================================================== --- sys/dev/e1000/e1000_api.c +++ sys/dev/e1000/e1000_api.c @@ -299,6 +299,12 @@ case E1000_DEV_ID_PCH_I218_V3: mac->type = e1000_pch_lpt; break; + case E1000_DEV_ID_PCH_SPT_I219_LM: + case E1000_DEV_ID_PCH_SPT_I219_V: + case E1000_DEV_ID_PCH_SPT_I219_LM2: + case E1000_DEV_ID_PCH_SPT_I219_V2: + mac->type = e1000_pch_spt; + break; case E1000_DEV_ID_82575EB_COPPER: case E1000_DEV_ID_82575EB_FIBER_SERDES: case E1000_DEV_ID_82575GB_QUAD_COPPER: @@ -449,6 +455,7 @@ case e1000_pchlan: case e1000_pch2lan: case e1000_pch_lpt: + case e1000_pch_spt: e1000_init_function_pointers_ich8lan(hw); break; case e1000_82575: @@ -929,21 +936,6 @@ } /** - * e1000_set_obff_timer - Set Optimized Buffer Flush/Fill timer - * @hw: pointer to the HW structure - * @itr: u32 indicating itr value - * - * Set the OBFF timer based on the given interrupt rate. - **/ -s32 e1000_set_obff_timer(struct e1000_hw *hw, u32 itr) -{ - if (hw->mac.ops.set_obff_timer) - return hw->mac.ops.set_obff_timer(hw, itr); - - return E1000_SUCCESS; -} - -/** * e1000_check_reset_block - Verifies PHY can be reset * @hw: pointer to the HW structure * @@ -1216,6 +1208,21 @@ } /** + * e1000_read_pba_num - Read device part number + * @hw: pointer to the HW structure + * @pba_num: pointer to device part number + * + * Reads the product board assembly (PBA) number from the EEPROM and stores + * the value in pba_num. + * Currently no func pointer exists and all implementations are handled in the + * generic version of this function. + **/ +s32 e1000_read_pba_num(struct e1000_hw *hw, u32 *pba_num) +{ + return e1000_read_pba_num_generic(hw, pba_num); +} + +/** * e1000_validate_nvm_checksum - Verifies NVM (EEPROM) checksum * @hw: pointer to the HW structure * Index: sys/dev/e1000/e1000_defines.h =================================================================== --- sys/dev/e1000/e1000_defines.h +++ sys/dev/e1000/e1000_defines.h @@ -197,6 +197,8 @@ #define E1000_RCTL_LBM_TCVR 0x000000C0 /* tcvr loopback mode */ #define E1000_RCTL_DTYP_PS 0x00000400 /* Packet Split descriptor */ #define E1000_RCTL_RDMTS_HALF 0x00000000 /* Rx desc min thresh size */ +#define E1000_RCTL_RDMTS_HEX 0x00010000 +#define E1000_RCTL_RDMTS1_HEX E1000_RCTL_RDMTS_HEX #define E1000_RCTL_MO_SHIFT 12 /* multicast offset shift */ #define E1000_RCTL_MO_3 0x00003000 /* multicast offset 15:4 */ #define E1000_RCTL_BAM 0x00008000 /* broadcast enable */ @@ -565,9 +567,6 @@ #define E1000_ICR_THS 0x00800000 /* ICR.THS: Thermal Sensor Event*/ #define E1000_ICR_MDDET 0x10000000 /* Malicious Driver Detect */ -#define E1000_ITR_MASK 0x000FFFFF /* ITR value bitfield */ -#define E1000_ITR_MULT 256 /* ITR mulitplier in nsec */ - /* PBA ECC Register */ #define E1000_PBA_ECC_COUNTER_MASK 0xFFF00000 /* ECC counter mask */ #define E1000_PBA_ECC_COUNTER_SHIFT 20 /* ECC counter shift value */ @@ -753,6 +752,12 @@ #define E1000_TSYNCTXCTL_VALID 0x00000001 /* Tx timestamp valid */ #define E1000_TSYNCTXCTL_ENABLED 0x00000010 /* enable Tx timestamping */ +/* HH Time Sync */ +#define E1000_TSYNCTXCTL_MAX_ALLOWED_DLY_MASK 0x0000F000 /* max delay */ +#define E1000_TSYNCTXCTL_SYNC_COMP_ERR 0x20000000 /* sync err */ +#define E1000_TSYNCTXCTL_SYNC_COMP 0x40000000 /* sync complete */ +#define E1000_TSYNCTXCTL_START_SYNC 0x80000000 /* initiate sync */ + #define E1000_TSYNCRXCTL_VALID 0x00000001 /* Rx timestamp valid */ #define E1000_TSYNCRXCTL_TYPE_MASK 0x0000000E /* Rx type mask */ #define E1000_TSYNCRXCTL_TYPE_L2_V2 0x00 @@ -1020,9 +1025,7 @@ /* NVM Addressing bits based on type 0=small, 1=large */ #define E1000_EECD_ADDR_BITS 0x00000400 #define E1000_EECD_TYPE 0x00002000 /* NVM Type (1-SPI, 0-Microwire) */ -#ifndef E1000_NVM_GRANT_ATTEMPTS #define E1000_NVM_GRANT_ATTEMPTS 1000 /* NVM # attempts to gain grant */ -#endif #define E1000_EECD_AUTO_RD 0x00000200 /* NVM Auto Read done */ #define E1000_EECD_SIZE_EX_MASK 0x00007800 /* NVM Size */ #define E1000_EECD_SIZE_EX_SHIFT 11 @@ -1059,11 +1062,44 @@ /* NVM Word Offsets */ #define NVM_COMPAT 0x0003 #define NVM_ID_LED_SETTINGS 0x0004 +#define NVM_VERSION 0x0005 #define NVM_SERDES_AMPLITUDE 0x0006 /* SERDES output amplitude */ #define NVM_PHY_CLASS_WORD 0x0007 #define E1000_I210_NVM_FW_MODULE_PTR 0x0010 #define E1000_I350_NVM_FW_MODULE_PTR 0x0051 #define NVM_FUTURE_INIT_WORD1 0x0019 +#define NVM_ETRACK_WORD 0x0042 +#define NVM_ETRACK_HIWORD 0x0043 +#define NVM_COMB_VER_OFF 0x0083 +#define NVM_COMB_VER_PTR 0x003d + +/* NVM version defines */ +#define NVM_MAJOR_MASK 0xF000 +#define NVM_MINOR_MASK 0x0FF0 +#define NVM_IMAGE_ID_MASK 0x000F +#define NVM_COMB_VER_MASK 0x00FF +#define NVM_MAJOR_SHIFT 12 +#define NVM_MINOR_SHIFT 4 +#define NVM_COMB_VER_SHFT 8 +#define NVM_VER_INVALID 0xFFFF +#define NVM_ETRACK_SHIFT 16 +#define NVM_ETRACK_VALID 0x8000 +#define NVM_NEW_DEC_MASK 0x0F00 +#define NVM_HEX_CONV 16 +#define NVM_HEX_TENS 10 + +/* FW version defines */ +/* Offset of "Loader patch ptr" in Firmware Header */ +#define E1000_I350_NVM_FW_LOADER_PATCH_PTR_OFFSET 0x01 +/* Patch generation hour & minutes */ +#define E1000_I350_NVM_FW_VER_WORD1_OFFSET 0x04 +/* Patch generation month & day */ +#define E1000_I350_NVM_FW_VER_WORD2_OFFSET 0x05 +/* Patch generation year */ +#define E1000_I350_NVM_FW_VER_WORD3_OFFSET 0x06 +/* Patch major & minor numbers */ +#define E1000_I350_NVM_FW_VER_WORD4_OFFSET 0x07 + #define NVM_MAC_ADDR 0x0000 #define NVM_SUB_DEV_ID 0x000B #define NVM_SUB_VEN_ID 0x000C @@ -1440,8 +1476,6 @@ #define I210_RXPBSIZE_DEFAULT 0x000000A2 /* RXPBSIZE default */ #define I210_TXPBSIZE_DEFAULT 0x04000014 /* TXPBSIZE default */ -#define E1000_DOBFFCTL_OBFFTHR_MASK 0x000000FF /* OBFF threshold */ -#define E1000_DOBFFCTL_EXIT_ACT_MASK 0x01000000 /* Exit active CB */ /* Proxy Filter Control */ #define E1000_PROXYFC_D0 0x00000001 /* Enable offload in D0 */ Index: sys/dev/e1000/e1000_hw.h =================================================================== --- sys/dev/e1000/e1000_hw.h +++ sys/dev/e1000/e1000_hw.h @@ -137,6 +137,10 @@ #define E1000_DEV_ID_PCH_I218_V2 0x15A1 #define E1000_DEV_ID_PCH_I218_LM3 0x15A2 /* Wildcat Point PCH */ #define E1000_DEV_ID_PCH_I218_V3 0x15A3 /* Wildcat Point PCH */ +#define E1000_DEV_ID_PCH_SPT_I219_LM 0x156F /* Sunrise Point PCH */ +#define E1000_DEV_ID_PCH_SPT_I219_V 0x1570 /* Sunrise Point PCH */ +#define E1000_DEV_ID_PCH_SPT_I219_LM2 0x15B7 /* Sunrise Point-H PCH */ +#define E1000_DEV_ID_PCH_SPT_I219_V2 0x15B8 /* Sunrise Point-H PCH */ #define E1000_DEV_ID_82576 0x10C9 #define E1000_DEV_ID_82576_FIBER 0x10E6 #define E1000_DEV_ID_82576_SERDES 0x10E7 @@ -222,6 +226,7 @@ e1000_pchlan, e1000_pch2lan, e1000_pch_lpt, + e1000_pch_spt, e1000_82575, e1000_82576, e1000_82580, @@ -703,7 +708,6 @@ int (*rar_set)(struct e1000_hw *, u8*, u32); s32 (*read_mac_addr)(struct e1000_hw *); s32 (*validate_mdi_setting)(struct e1000_hw *); - s32 (*set_obff_timer)(struct e1000_hw *, u32); s32 (*acquire_swfw_sync)(struct e1000_hw *, u16); void (*release_swfw_sync)(struct e1000_hw *, u16); }; @@ -805,7 +809,7 @@ enum e1000_serdes_link_state serdes_link_state; bool serdes_has_link; bool tx_pkt_filtering; - u32 max_frame_size; + u32 max_frame_size; }; struct e1000_phy_info { Index: sys/dev/e1000/e1000_i210.h =================================================================== --- sys/dev/e1000/e1000_i210.h +++ sys/dev/e1000/e1000_i210.h @@ -43,6 +43,8 @@ u16 words, u16 *data); s32 e1000_read_nvm_srrd_i210(struct e1000_hw *hw, u16 offset, u16 words, u16 *data); +s32 e1000_read_invm_version(struct e1000_hw *hw, + struct e1000_fw_version *invm_ver); s32 e1000_acquire_swfw_sync_i210(struct e1000_hw *hw, u16 mask); void e1000_release_swfw_sync_i210(struct e1000_hw *hw, u16 mask); s32 e1000_read_xmdio_reg(struct e1000_hw *hw, u16 addr, u8 dev_addr, Index: sys/dev/e1000/e1000_i210.c =================================================================== --- sys/dev/e1000/e1000_i210.c +++ sys/dev/e1000/e1000_i210.c @@ -489,6 +489,105 @@ } /** + * e1000_read_invm_version - Reads iNVM version and image type + * @hw: pointer to the HW structure + * @invm_ver: version structure for the version read + * + * Reads iNVM version and image type. + **/ +s32 e1000_read_invm_version(struct e1000_hw *hw, + struct e1000_fw_version *invm_ver) +{ + u32 *record = NULL; + u32 *next_record = NULL; + u32 i = 0; + u32 invm_dword = 0; + u32 invm_blocks = E1000_INVM_SIZE - (E1000_INVM_ULT_BYTES_SIZE / + E1000_INVM_RECORD_SIZE_IN_BYTES); + u32 buffer[E1000_INVM_SIZE]; + s32 status = -E1000_ERR_INVM_VALUE_NOT_FOUND; + u16 version = 0; + + DEBUGFUNC("e1000_read_invm_version"); + + /* Read iNVM memory */ + for (i = 0; i < E1000_INVM_SIZE; i++) { + invm_dword = E1000_READ_REG(hw, E1000_INVM_DATA_REG(i)); + buffer[i] = invm_dword; + } + + /* Read version number */ + for (i = 1; i < invm_blocks; i++) { + record = &buffer[invm_blocks - i]; + next_record = &buffer[invm_blocks - i + 1]; + + /* Check if we have first version location used */ + if ((i == 1) && ((*record & E1000_INVM_VER_FIELD_ONE) == 0)) { + version = 0; + status = E1000_SUCCESS; + break; + } + /* Check if we have second version location used */ + else if ((i == 1) && + ((*record & E1000_INVM_VER_FIELD_TWO) == 0)) { + version = (*record & E1000_INVM_VER_FIELD_ONE) >> 3; + status = E1000_SUCCESS; + break; + } + /* + * Check if we have odd version location + * used and it is the last one used + */ + else if ((((*record & E1000_INVM_VER_FIELD_ONE) == 0) && + ((*record & 0x3) == 0)) || (((*record & 0x3) != 0) && + (i != 1))) { + version = (*next_record & E1000_INVM_VER_FIELD_TWO) + >> 13; + status = E1000_SUCCESS; + break; + } + /* + * Check if we have even version location + * used and it is the last one used + */ + else if (((*record & E1000_INVM_VER_FIELD_TWO) == 0) && + ((*record & 0x3) == 0)) { + version = (*record & E1000_INVM_VER_FIELD_ONE) >> 3; + status = E1000_SUCCESS; + break; + } + } + + if (status == E1000_SUCCESS) { + invm_ver->invm_major = (version & E1000_INVM_MAJOR_MASK) + >> E1000_INVM_MAJOR_SHIFT; + invm_ver->invm_minor = version & E1000_INVM_MINOR_MASK; + } + /* Read Image Type */ + for (i = 1; i < invm_blocks; i++) { + record = &buffer[invm_blocks - i]; + next_record = &buffer[invm_blocks - i + 1]; + + /* Check if we have image type in first location used */ + if ((i == 1) && ((*record & E1000_INVM_IMGTYPE_FIELD) == 0)) { + invm_ver->invm_img_type = 0; + status = E1000_SUCCESS; + break; + } + /* Check if we have image type in first location used */ + else if ((((*record & 0x3) == 0) && + ((*record & E1000_INVM_IMGTYPE_FIELD) == 0)) || + ((((*record & 0x3) != 0) && (i != 1)))) { + invm_ver->invm_img_type = + (*next_record & E1000_INVM_IMGTYPE_FIELD) >> 23; + status = E1000_SUCCESS; + break; + } + } + return status; +} + +/** * e1000_validate_nvm_checksum_i210 - Validate EEPROM checksum * @hw: pointer to the HW structure * Index: sys/dev/e1000/e1000_ich8lan.h =================================================================== --- sys/dev/e1000/e1000_ich8lan.h +++ sys/dev/e1000/e1000_ich8lan.h @@ -35,11 +35,11 @@ #ifndef _E1000_ICH8LAN_H_ #define _E1000_ICH8LAN_H_ -#define ICH_FLASH_GFPREG 0x0000 -#define ICH_FLASH_HSFSTS 0x0004 -#define ICH_FLASH_HSFCTL 0x0006 -#define ICH_FLASH_FADDR 0x0008 -#define ICH_FLASH_FDATA0 0x0010 +#define ICH_FLASH_GFPREG 0xE000 +#define ICH_FLASH_HSFSTS 0xE004 +#define ICH_FLASH_HSFCTL 0xE006 +#define ICH_FLASH_FADDR 0xE008 +#define ICH_FLASH_FDATA0 0xE010 /* Requires up to 10 seconds when MNG might be accessing part. */ #define ICH_FLASH_READ_COMMAND_TIMEOUT 10000000 @@ -107,9 +107,25 @@ #define E1000_FEXTNVM6_REQ_PLL_CLK 0x00000100 #define E1000_FEXTNVM6_ENABLE_K1_ENTRY_CONDITION 0x00000200 - +#define E1000_FEXTNVM6_K1_OFF_ENABLE 0x80000000 +/* bit for disabling packet buffer read */ +#define E1000_FEXTNVM7_DISABLE_PB_READ 0x00040000 +#define E1000_FEXTNVM7_SIDE_CLK_UNGATE 0x00000004 #define E1000_FEXTNVM7_DISABLE_SMB_PERST 0x00000020 - +#define E1000_FEXTNVM9_IOSFSB_CLKGATE_DIS 0x00000800 +#define E1000_FEXTNVM9_IOSFSB_CLKREQ_DIS 0x00001000 +#define E1000_FEXTNVM11_DISABLE_PB_READ 0x00000200 +#define E1000_FEXTNVM11_DISABLE_MULR_FIX 0x00002000 + +/* bit24: RXDCTL thresholds granularity: 0 - cache lines, 1 - descriptors */ +#define E1000_RXDCTL_THRESH_UNIT_DESC 0x01000000 + +#define NVM_SIZE_MULTIPLIER 4096 /*multiplier for NVMS field*/ +#define E1000_FLASH_BASE_ADDR 0xE000 /*offset of NVM access regs*/ +#define E1000_CTRL_EXT_NVMVS 0x3 /*NVM valid sector */ +#define E1000_SPT_B_STEP_REV 0x10 /*SPT B step Rev ID*/ +#define E1000_TARC0_CB_MULTIQ_2_REQ (1 << 29) +#define E1000_TARC0_CB_MULTIQ_3_REQ (1 << 28 | 1 << 29) #define PCIE_ICH8_SNOOP_ALL PCIE_NO_SNOOP_ALL #define E1000_ICH_RAR_ENTRIES 7 @@ -171,6 +187,8 @@ #define E1000_NVM_K1_CONFIG 0x1B /* NVM K1 Config Word */ #define E1000_NVM_K1_ENABLE 0x1 /* NVM Enable K1 bit */ +#define K1_ENTRY_LATENCY 0 +#define K1_MIN_TIME 1 /* SMBus Control Phy Register */ #define CV_SMB_CTRL PHY_REG(769, 23) @@ -281,36 +299,13 @@ /* Receive Address Initial CRC Calculation */ #define E1000_PCH_RAICC(_n) (0x05F50 + ((_n) * 4)) -/* Latency Tolerance Reporting */ -#define E1000_LTRV 0x000F8 -#define E1000_LTRV_VALUE_MASK 0x000003FF -#define E1000_LTRV_SCALE_MAX 5 -#define E1000_LTRV_SCALE_FACTOR 5 -#define E1000_LTRV_SCALE_SHIFT 10 -#define E1000_LTRV_SCALE_MASK 0x00001C00 -#define E1000_LTRV_REQ_SHIFT 15 -#define E1000_LTRV_NOSNOOP_SHIFT 16 -#define E1000_LTRV_SEND (1 << 30) - -/* Proprietary Latency Tolerance Reporting PCI Capability */ -#define E1000_PCI_LTR_CAP_LPT 0xA8 - -/* OBFF Control & Threshold Defines */ -#define E1000_SVCR_OFF_EN 0x00000001 -#define E1000_SVCR_OFF_MASKINT 0x00001000 -#define E1000_SVCR_OFF_TIMER_MASK 0xFFFF0000 -#define E1000_SVCR_OFF_TIMER_SHIFT 16 -#define E1000_SVT_OFF_HWM_MASK 0x0000001F - -#if defined(QV_RELEASE) || !defined(NO_PCH_LPT_B0_SUPPORT) #define E1000_PCI_REVISION_ID_REG 0x08 -#endif /* defined(QV_RELEASE) || !defined(NO_PCH_LPT_B0_SUPPORT) */ void e1000_set_kmrn_lock_loss_workaround_ich8lan(struct e1000_hw *hw, bool state); void e1000_igp3_phy_powerdown_workaround_ich8lan(struct e1000_hw *hw); void e1000_gig_downshift_workaround_ich8lan(struct e1000_hw *hw); void e1000_suspend_workarounds_ich8lan(struct e1000_hw *hw); -void e1000_resume_workarounds_pchlan(struct e1000_hw *hw); +u32 e1000_resume_workarounds_pchlan(struct e1000_hw *hw); s32 e1000_configure_k1_ich8lan(struct e1000_hw *hw, bool k1_enable); void e1000_copy_rx_addrs_to_phy_ich8lan(struct e1000_hw *hw); s32 e1000_lv_jumbo_workaround_ich8lan(struct e1000_hw *hw, bool enable); Index: sys/dev/e1000/e1000_ich8lan.c =================================================================== --- sys/dev/e1000/e1000_ich8lan.c +++ sys/dev/e1000/e1000_ich8lan.c @@ -92,10 +92,13 @@ bool active); static s32 e1000_read_nvm_ich8lan(struct e1000_hw *hw, u16 offset, u16 words, u16 *data); +static s32 e1000_read_nvm_spt(struct e1000_hw *hw, u16 offset, u16 words, + u16 *data); static s32 e1000_write_nvm_ich8lan(struct e1000_hw *hw, u16 offset, u16 words, u16 *data); static s32 e1000_validate_nvm_checksum_ich8lan(struct e1000_hw *hw); static s32 e1000_update_nvm_checksum_ich8lan(struct e1000_hw *hw); +static s32 e1000_update_nvm_checksum_spt(struct e1000_hw *hw); static s32 e1000_valid_led_default_ich8lan(struct e1000_hw *hw, u16 *data); static s32 e1000_id_led_init_pchlan(struct e1000_hw *hw); @@ -123,6 +126,14 @@ u32 offset, u8 *data); static s32 e1000_read_flash_data_ich8lan(struct e1000_hw *hw, u32 offset, u8 size, u16 *data); +static s32 e1000_read_flash_data32_ich8lan(struct e1000_hw *hw, u32 offset, + u32 *data); +static s32 e1000_read_flash_dword_ich8lan(struct e1000_hw *hw, + u32 offset, u32 *data); +static s32 e1000_write_flash_data32_ich8lan(struct e1000_hw *hw, + u32 offset, u32 data); +static s32 e1000_retry_write_flash_dword_ich8lan(struct e1000_hw *hw, + u32 offset, u32 dword); static s32 e1000_read_flash_word_ich8lan(struct e1000_hw *hw, u32 offset, u16 *data); static s32 e1000_retry_write_flash_byte_ich8lan(struct e1000_hw *hw, @@ -133,7 +144,6 @@ static s32 e1000_set_mdio_slow_mode_hv(struct e1000_hw *hw); static s32 e1000_k1_workaround_lv(struct e1000_hw *hw); static void e1000_gate_hw_phy_config_ich8lan(struct e1000_hw *hw, bool gate); -static s32 e1000_set_obff_timer_pch_lpt(struct e1000_hw *hw, u32 itr); /* ICH GbE Flash Hardware Sequencing Flash Status Register bit breakdown */ /* Offset 04h HSFSTS */ @@ -232,16 +242,21 @@ if (ret_val) return FALSE; out: - if (hw->mac.type == e1000_pch_lpt) { - /* Unforce SMBus mode in PHY */ - hw->phy.ops.read_reg_locked(hw, CV_SMB_CTRL, &phy_reg); - phy_reg &= ~CV_SMB_CTRL_FORCE_SMBUS; - hw->phy.ops.write_reg_locked(hw, CV_SMB_CTRL, phy_reg); + if ((hw->mac.type == e1000_pch_lpt) || + (hw->mac.type == e1000_pch_spt)) { + /* Only unforce SMBus if ME is not active */ + if (!(E1000_READ_REG(hw, E1000_FWSM) & + E1000_ICH_FWSM_FW_VALID)) { + /* Unforce SMBus mode in PHY */ + hw->phy.ops.read_reg_locked(hw, CV_SMB_CTRL, &phy_reg); + phy_reg &= ~CV_SMB_CTRL_FORCE_SMBUS; + hw->phy.ops.write_reg_locked(hw, CV_SMB_CTRL, phy_reg); - /* Unforce SMBus mode in MAC */ - mac_reg = E1000_READ_REG(hw, E1000_CTRL_EXT); - mac_reg &= ~E1000_CTRL_EXT_FORCE_SMBUS; - E1000_WRITE_REG(hw, E1000_CTRL_EXT, mac_reg); + /* Unforce SMBus mode in MAC */ + mac_reg = E1000_READ_REG(hw, E1000_CTRL_EXT); + mac_reg &= ~E1000_CTRL_EXT_FORCE_SMBUS; + E1000_WRITE_REG(hw, E1000_CTRL_EXT, mac_reg); + } } return TRUE; @@ -328,6 +343,7 @@ */ switch (hw->mac.type) { case e1000_pch_lpt: + case e1000_pch_spt: if (e1000_phy_is_accessible_pchlan(hw)) break; @@ -475,6 +491,7 @@ /* fall-through */ case e1000_pch2lan: case e1000_pch_lpt: + case e1000_pch_spt: /* In case the PHY needs to be in mdio slow mode, * set slow mode and try to get the PHY id again. */ @@ -617,36 +634,53 @@ struct e1000_dev_spec_ich8lan *dev_spec = &hw->dev_spec.ich8lan; u32 gfpreg, sector_base_addr, sector_end_addr; u16 i; + u32 nvm_size; DEBUGFUNC("e1000_init_nvm_params_ich8lan"); /* Can't read flash registers if the register set isn't mapped. */ nvm->type = e1000_nvm_flash_sw; - if (!hw->flash_address) { - DEBUGOUT("ERROR: Flash registers not mapped\n"); - return -E1000_ERR_CONFIG; - } + /* in SPT, gfpreg doesn't exist. NVM size is taken from the + * STRAP register + */ + if (hw->mac.type == e1000_pch_spt) { + nvm->flash_base_addr = 0; + nvm_size = + (((E1000_READ_REG(hw, E1000_STRAP) >> 1) & 0x1F) + 1) + * NVM_SIZE_MULTIPLIER; + nvm->flash_bank_size = nvm_size / 2; + /* Adjust to word count */ + nvm->flash_bank_size /= sizeof(u16); + /* Set the base address for flash register access */ + hw->flash_address = hw->hw_addr + E1000_FLASH_BASE_ADDR; + } else { + if (!hw->flash_address) { + DEBUGOUT("ERROR: Flash registers not mapped\n"); + return -E1000_ERR_CONFIG; + } + + gfpreg = E1000_READ_FLASH_REG(hw, ICH_FLASH_GFPREG); + + /* sector_X_addr is a "sector"-aligned address (4096 bytes) + * Add 1 to sector_end_addr since this sector is included in + * the overall size. + */ + sector_base_addr = gfpreg & FLASH_GFPREG_BASE_MASK; + sector_end_addr = ((gfpreg >> 16) & FLASH_GFPREG_BASE_MASK) + 1; - gfpreg = E1000_READ_FLASH_REG(hw, ICH_FLASH_GFPREG); + /* flash_base_addr is byte-aligned */ + nvm->flash_base_addr = sector_base_addr + << FLASH_SECTOR_ADDR_SHIFT; - /* sector_X_addr is a "sector"-aligned address (4096 bytes) - * Add 1 to sector_end_addr since this sector is included in - * the overall size. - */ - sector_base_addr = gfpreg & FLASH_GFPREG_BASE_MASK; - sector_end_addr = ((gfpreg >> 16) & FLASH_GFPREG_BASE_MASK) + 1; - - /* flash_base_addr is byte-aligned */ - nvm->flash_base_addr = sector_base_addr << FLASH_SECTOR_ADDR_SHIFT; - - /* find total size of the NVM, then cut in half since the total - * size represents two separate NVM banks. - */ - nvm->flash_bank_size = ((sector_end_addr - sector_base_addr) - << FLASH_SECTOR_ADDR_SHIFT); - nvm->flash_bank_size /= 2; - /* Adjust to word count */ - nvm->flash_bank_size /= sizeof(u16); + /* find total size of the NVM, then cut in half since the total + * size represents two separate NVM banks. + */ + nvm->flash_bank_size = ((sector_end_addr - sector_base_addr) + << FLASH_SECTOR_ADDR_SHIFT); + nvm->flash_bank_size /= 2; + /* Adjust to word count */ + nvm->flash_bank_size /= sizeof(u16); + } nvm->word_size = E1000_SHADOW_RAM_WORDS; @@ -662,8 +696,13 @@ /* Function Pointers */ nvm->ops.acquire = e1000_acquire_nvm_ich8lan; nvm->ops.release = e1000_release_nvm_ich8lan; - nvm->ops.read = e1000_read_nvm_ich8lan; - nvm->ops.update = e1000_update_nvm_checksum_ich8lan; + if (hw->mac.type == e1000_pch_spt) { + nvm->ops.read = e1000_read_nvm_spt; + nvm->ops.update = e1000_update_nvm_checksum_spt; + } else { + nvm->ops.read = e1000_read_nvm_ich8lan; + nvm->ops.update = e1000_update_nvm_checksum_ich8lan; + } nvm->ops.valid_led_default = e1000_valid_led_default_ich8lan; nvm->ops.validate = e1000_validate_nvm_checksum_ich8lan; nvm->ops.write = e1000_write_nvm_ich8lan; @@ -681,9 +720,7 @@ static s32 e1000_init_mac_params_ich8lan(struct e1000_hw *hw) { struct e1000_mac_info *mac = &hw->mac; -#if defined(QV_RELEASE) || !defined(NO_PCH_LPT_B0_SUPPORT) u16 pci_cfg; -#endif /* QV_RELEASE || !defined(NO_PCH_LPT_B0_SUPPORT) */ DEBUGFUNC("e1000_init_mac_params_ich8lan"); @@ -752,15 +789,21 @@ mac->ops.rar_set = e1000_rar_set_pch2lan; /* fall-through */ case e1000_pch_lpt: + case e1000_pch_spt: /* multicast address update for pch2 */ mac->ops.update_mc_addr_list = e1000_update_mc_addr_list_pch2lan; + /* fall-through */ case e1000_pchlan: -#if defined(QV_RELEASE) || !defined(NO_PCH_LPT_B0_SUPPORT) /* save PCH revision_id */ e1000_read_pci_cfg(hw, E1000_PCI_REVISION_ID_REG, &pci_cfg); - hw->revision_id = (u8)(pci_cfg &= 0x000F); -#endif /* QV_RELEASE || !defined(NO_PCH_LPT_B0_SUPPORT) */ + /* SPT uses full byte for revision ID, + * as opposed to previous generations + */ + if (hw->mac.type >= e1000_pch_spt) + hw->revision_id = (u8)(pci_cfg &= 0x00FF); + else + hw->revision_id = (u8)(pci_cfg &= 0x000F); /* check management mode */ mac->ops.check_mng_mode = e1000_check_mng_mode_pchlan; /* ID LED init */ @@ -777,11 +820,11 @@ break; } - if (mac->type == e1000_pch_lpt) { + if ((mac->type == e1000_pch_lpt) || + (mac->type == e1000_pch_spt)) { mac->rar_entry_count = E1000_PCH_LPT_RAR_ENTRIES; mac->ops.rar_set = e1000_rar_set_pch_lpt; mac->ops.setup_physical_interface = e1000_setup_copper_link_pch_lpt; - mac->ops.set_obff_timer = e1000_set_obff_timer_pch_lpt; } /* Enable PCS Lock-loss workaround for ICH8 */ @@ -1007,8 +1050,9 @@ /* clear FEXTNVM6 bit 8 on link down or 10/100 */ fextnvm6 &= ~E1000_FEXTNVM6_REQ_PLL_CLK; - if (!link || ((status & E1000_STATUS_SPEED_100) && - (status & E1000_STATUS_FD))) + if ((hw->phy.revision > 5) || !link || + ((status & E1000_STATUS_SPEED_100) && + (status & E1000_STATUS_FD))) goto update_fextnvm6; ret_val = hw->phy.ops.read_reg(hw, I217_INBAND_CTRL, ®); @@ -1044,168 +1088,6 @@ return ret_val; } -static u64 e1000_ltr2ns(u16 ltr) -{ - u32 value, scale; - - /* Determine the latency in nsec based on the LTR value & scale */ - value = ltr & E1000_LTRV_VALUE_MASK; - scale = (ltr & E1000_LTRV_SCALE_MASK) >> E1000_LTRV_SCALE_SHIFT; - - return value * (1 << (scale * E1000_LTRV_SCALE_FACTOR)); -} - -/** - * e1000_platform_pm_pch_lpt - Set platform power management values - * @hw: pointer to the HW structure - * @link: bool indicating link status - * - * Set the Latency Tolerance Reporting (LTR) values for the "PCIe-like" - * GbE MAC in the Lynx Point PCH based on Rx buffer size and link speed - * when link is up (which must not exceed the maximum latency supported - * by the platform), otherwise specify there is no LTR requirement. - * Unlike TRUE-PCIe devices which set the LTR maximum snoop/no-snoop - * latencies in the LTR Extended Capability Structure in the PCIe Extended - * Capability register set, on this device LTR is set by writing the - * equivalent snoop/no-snoop latencies in the LTRV register in the MAC and - * set the SEND bit to send an Intel On-chip System Fabric sideband (IOSF-SB) - * message to the PMC. - * - * Use the LTR value to calculate the Optimized Buffer Flush/Fill (OBFF) - * high-water mark. - **/ -static s32 e1000_platform_pm_pch_lpt(struct e1000_hw *hw, bool link) -{ - u32 reg = link << (E1000_LTRV_REQ_SHIFT + E1000_LTRV_NOSNOOP_SHIFT) | - link << E1000_LTRV_REQ_SHIFT | E1000_LTRV_SEND; - u16 lat_enc = 0; /* latency encoded */ - s32 obff_hwm = 0; - - DEBUGFUNC("e1000_platform_pm_pch_lpt"); - - if (link) { - u16 speed, duplex, scale = 0; - u16 max_snoop, max_nosnoop; - u16 max_ltr_enc; /* max LTR latency encoded */ - s64 lat_ns; - s64 value; - u32 rxa; - - if (!hw->mac.max_frame_size) { - DEBUGOUT("max_frame_size not set.\n"); - return -E1000_ERR_CONFIG; - } - - hw->mac.ops.get_link_up_info(hw, &speed, &duplex); - if (!speed) { - DEBUGOUT("Speed not set.\n"); - return -E1000_ERR_CONFIG; - } - - /* Rx Packet Buffer Allocation size (KB) */ - rxa = E1000_READ_REG(hw, E1000_PBA) & E1000_PBA_RXA_MASK; - - /* Determine the maximum latency tolerated by the device. - * - * Per the PCIe spec, the tolerated latencies are encoded as - * a 3-bit encoded scale (only 0-5 are valid) multiplied by - * a 10-bit value (0-1023) to provide a range from 1 ns to - * 2^25*(2^10-1) ns. The scale is encoded as 0=2^0ns, - * 1=2^5ns, 2=2^10ns,...5=2^25ns. - */ - lat_ns = ((s64)rxa * 1024 - - (2 * (s64)hw->mac.max_frame_size)) * 8 * 1000; - if (lat_ns < 0) - lat_ns = 0; - else - lat_ns /= speed; - value = lat_ns; - - while (value > E1000_LTRV_VALUE_MASK) { - scale++; - value = E1000_DIVIDE_ROUND_UP(value, (1 << 5)); - } - if (scale > E1000_LTRV_SCALE_MAX) { - DEBUGOUT1("Invalid LTR latency scale %d\n", scale); - return -E1000_ERR_CONFIG; - } - lat_enc = (u16)((scale << E1000_LTRV_SCALE_SHIFT) | value); - - /* Determine the maximum latency tolerated by the platform */ - e1000_read_pci_cfg(hw, E1000_PCI_LTR_CAP_LPT, &max_snoop); - e1000_read_pci_cfg(hw, E1000_PCI_LTR_CAP_LPT + 2, &max_nosnoop); - max_ltr_enc = E1000_MAX(max_snoop, max_nosnoop); - - if (lat_enc > max_ltr_enc) { - lat_enc = max_ltr_enc; - lat_ns = e1000_ltr2ns(max_ltr_enc); - } - - if (lat_ns) { - lat_ns *= speed * 1000; - lat_ns /= 8; - lat_ns /= 1000000000; - obff_hwm = (s32)(rxa - lat_ns); - } - if ((obff_hwm < 0) || (obff_hwm > E1000_SVT_OFF_HWM_MASK)) { - DEBUGOUT1("Invalid high water mark %d\n", obff_hwm); - return -E1000_ERR_CONFIG; - } - } - - /* Set Snoop and No-Snoop latencies the same */ - reg |= lat_enc | (lat_enc << E1000_LTRV_NOSNOOP_SHIFT); - E1000_WRITE_REG(hw, E1000_LTRV, reg); - - /* Set OBFF high water mark */ - reg = E1000_READ_REG(hw, E1000_SVT) & ~E1000_SVT_OFF_HWM_MASK; - reg |= obff_hwm; - E1000_WRITE_REG(hw, E1000_SVT, reg); - - /* Enable OBFF */ - reg = E1000_READ_REG(hw, E1000_SVCR); - reg |= E1000_SVCR_OFF_EN; - /* Always unblock interrupts to the CPU even when the system is - * in OBFF mode. This ensures that small round-robin traffic - * (like ping) does not get dropped or experience long latency. - */ - reg |= E1000_SVCR_OFF_MASKINT; - E1000_WRITE_REG(hw, E1000_SVCR, reg); - - return E1000_SUCCESS; -} - -/** - * e1000_set_obff_timer_pch_lpt - Update Optimized Buffer Flush/Fill timer - * @hw: pointer to the HW structure - * @itr: interrupt throttling rate - * - * Configure OBFF with the updated interrupt rate. - **/ -static s32 e1000_set_obff_timer_pch_lpt(struct e1000_hw *hw, u32 itr) -{ - u32 svcr; - s32 timer; - - DEBUGFUNC("e1000_set_obff_timer_pch_lpt"); - - /* Convert ITR value into microseconds for OBFF timer */ - timer = itr & E1000_ITR_MASK; - timer = (timer * E1000_ITR_MULT) / 1000; - - if ((timer < 0) || (timer > E1000_ITR_MASK)) { - DEBUGOUT1("Invalid OBFF timer %d\n", timer); - return -E1000_ERR_CONFIG; - } - - svcr = E1000_READ_REG(hw, E1000_SVCR); - svcr &= ~E1000_SVCR_OFF_TIMER_MASK; - svcr |= timer << E1000_SVCR_OFF_TIMER_SHIFT; - E1000_WRITE_REG(hw, E1000_SVCR, svcr); - - return E1000_SUCCESS; -} - /** * e1000_enable_ulp_lpt_lp - configure Ultra Low Power mode for LynxPoint-LP * @hw: pointer to the HW structure @@ -1221,6 +1103,7 @@ u32 mac_reg; s32 ret_val = E1000_SUCCESS; u16 phy_reg; + u16 oem_reg = 0; if ((hw->mac.type < e1000_pch_lpt) || (hw->device_id == E1000_DEV_ID_PCH_LPT_I217_LM) || @@ -1276,6 +1159,25 @@ mac_reg |= E1000_CTRL_EXT_FORCE_SMBUS; E1000_WRITE_REG(hw, E1000_CTRL_EXT, mac_reg); + /* Si workaround for ULP entry flow on i127/rev6 h/w. Enable + * LPLU and disable Gig speed when entering ULP + */ + if ((hw->phy.type == e1000_phy_i217) && (hw->phy.revision == 6)) { + ret_val = e1000_read_phy_reg_hv_locked(hw, HV_OEM_BITS, + &oem_reg); + if (ret_val) + goto release; + + phy_reg = oem_reg; + phy_reg |= HV_OEM_BITS_LPLU | HV_OEM_BITS_GBE_DIS; + + ret_val = e1000_write_phy_reg_hv_locked(hw, HV_OEM_BITS, + phy_reg); + + if (ret_val) + goto release; + } + /* Set Inband ULP Exit, Reset to SMBus mode and * Disable SMBus Release on PERST# in PHY */ @@ -1287,10 +1189,15 @@ if (to_sx) { if (E1000_READ_REG(hw, E1000_WUFC) & E1000_WUFC_LNKC) phy_reg |= I218_ULP_CONFIG1_WOL_HOST; + else + phy_reg &= ~I218_ULP_CONFIG1_WOL_HOST; phy_reg |= I218_ULP_CONFIG1_STICKY_ULP; + phy_reg &= ~I218_ULP_CONFIG1_INBAND_EXIT; } else { phy_reg |= I218_ULP_CONFIG1_INBAND_EXIT; + phy_reg &= ~I218_ULP_CONFIG1_STICKY_ULP; + phy_reg &= ~I218_ULP_CONFIG1_WOL_HOST; } e1000_write_phy_reg_hv_locked(hw, I218_ULP_CONFIG1, phy_reg); @@ -1302,6 +1209,16 @@ /* Commit ULP changes in PHY by starting auto ULP configuration */ phy_reg |= I218_ULP_CONFIG1_START; e1000_write_phy_reg_hv_locked(hw, I218_ULP_CONFIG1, phy_reg); + + if ((hw->phy.type == e1000_phy_i217) && (hw->phy.revision == 6) && + to_sx && (E1000_READ_REG(hw, E1000_STATUS) & E1000_STATUS_LU)) { + + ret_val = e1000_write_phy_reg_hv_locked(hw, HV_OEM_BITS, + oem_reg); + if (ret_val) + goto release; + } + release: hw->phy.ops.release(hw); out: @@ -1467,7 +1384,8 @@ static s32 e1000_check_for_copper_link_ich8lan(struct e1000_hw *hw) { struct e1000_mac_info *mac = &hw->mac; - s32 ret_val; + s32 ret_val, tipg_reg = 0; + u16 emi_addr, emi_val = 0; bool link; u16 phy_reg; @@ -1500,35 +1418,92 @@ * the IPG and reduce Rx latency in the PHY. */ if (((hw->mac.type == e1000_pch2lan) || - (hw->mac.type == e1000_pch_lpt)) && link) { - u32 reg; - reg = E1000_READ_REG(hw, E1000_STATUS); - if (!(reg & (E1000_STATUS_FD | E1000_STATUS_SPEED_MASK))) { - u16 emi_addr; - - reg = E1000_READ_REG(hw, E1000_TIPG); - reg &= ~E1000_TIPG_IPGT_MASK; - reg |= 0xFF; - E1000_WRITE_REG(hw, E1000_TIPG, reg); + (hw->mac.type == e1000_pch_lpt) || + (hw->mac.type == e1000_pch_spt)) && link) { + u16 speed, duplex; + + e1000_get_speed_and_duplex_copper_generic(hw, &speed, &duplex); + tipg_reg = E1000_READ_REG(hw, E1000_TIPG); + tipg_reg &= ~E1000_TIPG_IPGT_MASK; + if (duplex == HALF_DUPLEX && speed == SPEED_10) { + tipg_reg |= 0xFF; /* Reduce Rx latency in analog PHY */ - ret_val = hw->phy.ops.acquire(hw); - if (ret_val) - return ret_val; + emi_val = 0; + } else if (hw->mac.type == e1000_pch_spt && + duplex == FULL_DUPLEX && speed != SPEED_1000) { + tipg_reg |= 0xC; + emi_val = 1; + } else { + /* Roll back the default values */ + tipg_reg |= 0x08; + emi_val = 1; + } - if (hw->mac.type == e1000_pch2lan) - emi_addr = I82579_RX_CONFIG; - else - emi_addr = I217_RX_CONFIG; - ret_val = e1000_write_emi_reg_locked(hw, emi_addr, 0); + E1000_WRITE_REG(hw, E1000_TIPG, tipg_reg); + + ret_val = hw->phy.ops.acquire(hw); + if (ret_val) + return ret_val; + + if (hw->mac.type == e1000_pch2lan) + emi_addr = I82579_RX_CONFIG; + else + emi_addr = I217_RX_CONFIG; + ret_val = e1000_write_emi_reg_locked(hw, emi_addr, emi_val); - hw->phy.ops.release(hw); + hw->phy.ops.release(hw); - if (ret_val) - return ret_val; + if (ret_val) + return ret_val; + + if (hw->mac.type == e1000_pch_spt) { + u16 data; + u16 ptr_gap; + + if (speed == SPEED_1000) { + ret_val = hw->phy.ops.acquire(hw); + if (ret_val) + return ret_val; + + ret_val = hw->phy.ops.read_reg_locked(hw, + PHY_REG(776, 20), + &data); + if (ret_val) { + hw->phy.ops.release(hw); + return ret_val; + } + + ptr_gap = (data & (0x3FF << 2)) >> 2; + if (ptr_gap < 0x18) { + data &= ~(0x3FF << 2); + data |= (0x18 << 2); + ret_val = + hw->phy.ops.write_reg_locked(hw, + PHY_REG(776, 20), data); + } + hw->phy.ops.release(hw); + if (ret_val) + return ret_val; + } } } + /* I217 Packet Loss issue: + * ensure that FEXTNVM4 Beacon Duration is set correctly + * on power up. + * Set the Beacon Duration for I217 to 8 usec + */ + if ((hw->mac.type == e1000_pch_lpt) || + (hw->mac.type == e1000_pch_spt)) { + u32 mac_reg; + + mac_reg = E1000_READ_REG(hw, E1000_FEXTNVM4); + mac_reg &= ~E1000_FEXTNVM4_BEACON_DURATION_MASK; + mac_reg |= E1000_FEXTNVM4_BEACON_DURATION_8USEC; + E1000_WRITE_REG(hw, E1000_FEXTNVM4, mac_reg); + } + /* Work-around I218 hang issue */ if ((hw->device_id == E1000_DEV_ID_PCH_LPTLP_I218_LM) || (hw->device_id == E1000_DEV_ID_PCH_LPTLP_I218_V) || @@ -1538,19 +1513,22 @@ if (ret_val) return ret_val; } - if (hw->mac.type == e1000_pch_lpt) { - /* Set platform power management values for - * Latency Tolerance Reporting (LTR) - * Optimized Buffer Flush/Fill (OBFF) - */ - ret_val = e1000_platform_pm_pch_lpt(hw, link); - if (ret_val) - return ret_val; - } - /* Clear link partner's EEE ability */ hw->dev_spec.ich8lan.eee_lp_ability = 0; + /* FEXTNVM6 K1-off workaround */ + if (hw->mac.type == e1000_pch_spt) { + u32 pcieanacfg = E1000_READ_REG(hw, E1000_PCIEANACFG); + u32 fextnvm6 = E1000_READ_REG(hw, E1000_FEXTNVM6); + + if (pcieanacfg & E1000_FEXTNVM6_K1_OFF_ENABLE) + fextnvm6 |= E1000_FEXTNVM6_K1_OFF_ENABLE; + else + fextnvm6 &= ~E1000_FEXTNVM6_K1_OFF_ENABLE; + + E1000_WRITE_REG(hw, E1000_FEXTNVM6, fextnvm6); + } + if (!link) return E1000_SUCCESS; /* No link detected */ @@ -1644,6 +1622,7 @@ case e1000_pchlan: case e1000_pch2lan: case e1000_pch_lpt: + case e1000_pch_spt: hw->phy.ops.init_params = e1000_init_phy_params_pchlan; break; default: @@ -2107,6 +2086,7 @@ case e1000_pchlan: case e1000_pch2lan: case e1000_pch_lpt: + case e1000_pch_spt: sw_cfg_mask = E1000_FEXTNVM_SW_CONFIG_ICH8M; break; default: @@ -3222,6 +3202,20 @@ DEBUGFUNC("e1000_valid_nvm_bank_detect_ich8lan"); switch (hw->mac.type) { + /* In SPT, read from the CTRL_EXT reg instead of + * accessing the sector valid bits from the nvm + */ + case e1000_pch_spt: + *bank = E1000_READ_REG(hw, E1000_CTRL_EXT) + & E1000_CTRL_EXT_NVMVS; + if ((*bank == 0) || (*bank == 1)) { + DEBUGOUT("ERROR: No valid NVM bank present\n"); + return -E1000_ERR_NVM; + } else { + *bank = *bank - 2; + return E1000_SUCCESS; + } + break; case e1000_ich8lan: case e1000_ich9lan: eecd = E1000_READ_REG(hw, E1000_EECD); @@ -3269,6 +3263,99 @@ } /** + * e1000_read_nvm_spt - NVM access for SPT + * @hw: pointer to the HW structure + * @offset: The offset (in bytes) of the word(s) to read. + * @words: Size of data to read in words. + * @data: pointer to the word(s) to read at offset. + * + * Reads a word(s) from the NVM + **/ +static s32 e1000_read_nvm_spt(struct e1000_hw *hw, u16 offset, u16 words, + u16 *data) +{ + struct e1000_nvm_info *nvm = &hw->nvm; + struct e1000_dev_spec_ich8lan *dev_spec = &hw->dev_spec.ich8lan; + u32 act_offset; + s32 ret_val = E1000_SUCCESS; + u32 bank = 0; + u32 dword = 0; + u16 offset_to_read; + u16 i; + + DEBUGFUNC("e1000_read_nvm_spt"); + + if ((offset >= nvm->word_size) || (words > nvm->word_size - offset) || + (words == 0)) { + DEBUGOUT("nvm parameter(s) out of bounds\n"); + ret_val = -E1000_ERR_NVM; + goto out; + } + + nvm->ops.acquire(hw); + + ret_val = e1000_valid_nvm_bank_detect_ich8lan(hw, &bank); + if (ret_val != E1000_SUCCESS) { + DEBUGOUT("Could not detect valid bank, assuming bank 0\n"); + bank = 0; + } + + act_offset = (bank) ? nvm->flash_bank_size : 0; + act_offset += offset; + + ret_val = E1000_SUCCESS; + + for (i = 0; i < words; i += 2) { + if (words - i == 1) { + if (dev_spec->shadow_ram[offset+i].modified) { + data[i] = dev_spec->shadow_ram[offset+i].value; + } else { + offset_to_read = act_offset + i - + ((act_offset + i) % 2); + ret_val = + e1000_read_flash_dword_ich8lan(hw, + offset_to_read, + &dword); + if (ret_val) + break; + if ((act_offset + i) % 2 == 0) + data[i] = (u16)(dword & 0xFFFF); + else + data[i] = (u16)((dword >> 16) & 0xFFFF); + } + } else { + offset_to_read = act_offset + i; + if (!(dev_spec->shadow_ram[offset+i].modified) || + !(dev_spec->shadow_ram[offset+i+1].modified)) { + ret_val = + e1000_read_flash_dword_ich8lan(hw, + offset_to_read, + &dword); + if (ret_val) + break; + } + if (dev_spec->shadow_ram[offset+i].modified) + data[i] = dev_spec->shadow_ram[offset+i].value; + else + data[i] = (u16) (dword & 0xFFFF); + if (dev_spec->shadow_ram[offset+i].modified) + data[i+1] = + dev_spec->shadow_ram[offset+i+1].value; + else + data[i+1] = (u16) (dword >> 16 & 0xFFFF); + } + } + + nvm->ops.release(hw); + +out: + if (ret_val) + DEBUGOUT1("NVM read error: %d\n", ret_val); + + return ret_val; +} + +/** * e1000_read_nvm_ich8lan - Read word(s) from the NVM * @hw: pointer to the HW structure * @offset: The offset (in bytes) of the word(s) to read. @@ -3355,7 +3442,11 @@ /* Clear FCERR and DAEL in hw status by writing 1 */ hsfsts.hsf_status.flcerr = 1; hsfsts.hsf_status.dael = 1; - E1000_WRITE_FLASH_REG16(hw, ICH_FLASH_HSFSTS, hsfsts.regval); + if (hw->mac.type == e1000_pch_spt) + E1000_WRITE_FLASH_REG(hw, ICH_FLASH_HSFSTS, + hsfsts.regval & 0xFFFF); + else + E1000_WRITE_FLASH_REG16(hw, ICH_FLASH_HSFSTS, hsfsts.regval); /* Either we should have a hardware SPI cycle in progress * bit to check against, in order to start a new cycle or @@ -3371,7 +3462,12 @@ * Begin by setting Flash Cycle Done. */ hsfsts.hsf_status.flcdone = 1; - E1000_WRITE_FLASH_REG16(hw, ICH_FLASH_HSFSTS, hsfsts.regval); + if (hw->mac.type == e1000_pch_spt) + E1000_WRITE_FLASH_REG(hw, ICH_FLASH_HSFSTS, + hsfsts.regval & 0xFFFF); + else + E1000_WRITE_FLASH_REG16(hw, ICH_FLASH_HSFSTS, + hsfsts.regval); ret_val = E1000_SUCCESS; } else { s32 i; @@ -3393,8 +3489,12 @@ * now set the Flash Cycle Done. */ hsfsts.hsf_status.flcdone = 1; - E1000_WRITE_FLASH_REG16(hw, ICH_FLASH_HSFSTS, - hsfsts.regval); + if (hw->mac.type == e1000_pch_spt) + E1000_WRITE_FLASH_REG(hw, ICH_FLASH_HSFSTS, + hsfsts.regval & 0xFFFF); + else + E1000_WRITE_FLASH_REG16(hw, ICH_FLASH_HSFSTS, + hsfsts.regval); } else { DEBUGOUT("Flash controller busy, cannot get access\n"); } @@ -3419,10 +3519,17 @@ DEBUGFUNC("e1000_flash_cycle_ich8lan"); /* Start a cycle by writing 1 in Flash Cycle Go in Hw Flash Control */ - hsflctl.regval = E1000_READ_FLASH_REG16(hw, ICH_FLASH_HSFCTL); + if (hw->mac.type == e1000_pch_spt) + hsflctl.regval = E1000_READ_FLASH_REG(hw, ICH_FLASH_HSFSTS)>>16; + else + hsflctl.regval = E1000_READ_FLASH_REG16(hw, ICH_FLASH_HSFCTL); hsflctl.hsf_ctrl.flcgo = 1; - E1000_WRITE_FLASH_REG16(hw, ICH_FLASH_HSFCTL, hsflctl.regval); + if (hw->mac.type == e1000_pch_spt) + E1000_WRITE_FLASH_REG(hw, ICH_FLASH_HSFSTS, + hsflctl.regval << 16); + else + E1000_WRITE_FLASH_REG16(hw, ICH_FLASH_HSFCTL, hsflctl.regval); /* wait till FDONE bit is set to 1 */ do { @@ -3439,6 +3546,29 @@ } /** + * e1000_read_flash_dword_ich8lan - Read dword from flash + * @hw: pointer to the HW structure + * @offset: offset to data location + * @data: pointer to the location for storing the data + * + * Reads the flash dword at offset into data. Offset is converted + * to bytes before read. + **/ +static s32 e1000_read_flash_dword_ich8lan(struct e1000_hw *hw, u32 offset, + u32 *data) +{ + DEBUGFUNC("e1000_read_flash_dword_ich8lan"); + + if (!data) + return -E1000_ERR_NVM; + + /* Must convert word offset into bytes. */ + offset <<= 1; + + return e1000_read_flash_data32_ich8lan(hw, offset, data); +} + +/** * e1000_read_flash_word_ich8lan - Read word from flash * @hw: pointer to the HW structure * @offset: offset to data location @@ -3475,7 +3605,13 @@ s32 ret_val; u16 word = 0; - ret_val = e1000_read_flash_data_ich8lan(hw, offset, 1, &word); + /* In SPT, only 32 bits access is supported, + * so this function should not be called. + */ + if (hw->mac.type == e1000_pch_spt) + return -E1000_ERR_NVM; + else + ret_val = e1000_read_flash_data_ich8lan(hw, offset, 1, &word); if (ret_val) return ret_val; @@ -3563,35 +3699,113 @@ /** - * e1000_write_nvm_ich8lan - Write word(s) to the NVM + * e1000_read_flash_data32_ich8lan - Read dword from NVM * @hw: pointer to the HW structure - * @offset: The offset (in bytes) of the word(s) to write. - * @words: Size of data to write in words - * @data: Pointer to the word(s) to write at offset. + * @offset: The offset (in bytes) of the dword to read. + * @data: Pointer to the dword to store the value read. * - * Writes a byte or word to the NVM using the flash access registers. + * Reads a byte or word from the NVM using the flash access registers. **/ -static s32 e1000_write_nvm_ich8lan(struct e1000_hw *hw, u16 offset, u16 words, - u16 *data) -{ - struct e1000_nvm_info *nvm = &hw->nvm; - struct e1000_dev_spec_ich8lan *dev_spec = &hw->dev_spec.ich8lan; - u16 i; - DEBUGFUNC("e1000_write_nvm_ich8lan"); +static s32 e1000_read_flash_data32_ich8lan(struct e1000_hw *hw, u32 offset, + u32 *data) +{ + union ich8_hws_flash_status hsfsts; + union ich8_hws_flash_ctrl hsflctl; + u32 flash_linear_addr; + s32 ret_val = -E1000_ERR_NVM; + u8 count = 0; - if ((offset >= nvm->word_size) || (words > nvm->word_size - offset) || - (words == 0)) { - DEBUGOUT("nvm parameter(s) out of bounds\n"); - return -E1000_ERR_NVM; - } + DEBUGFUNC("e1000_read_flash_data_ich8lan"); - nvm->ops.acquire(hw); + if (offset > ICH_FLASH_LINEAR_ADDR_MASK || + hw->mac.type != e1000_pch_spt) + return -E1000_ERR_NVM; + flash_linear_addr = ((ICH_FLASH_LINEAR_ADDR_MASK & offset) + + hw->nvm.flash_base_addr); - for (i = 0; i < words; i++) { - dev_spec->shadow_ram[offset+i].modified = TRUE; - dev_spec->shadow_ram[offset+i].value = data[i]; - } + do { + usec_delay(1); + /* Steps */ + ret_val = e1000_flash_cycle_init_ich8lan(hw); + if (ret_val != E1000_SUCCESS) + break; + /* In SPT, This register is in Lan memory space, not flash. + * Therefore, only 32 bit access is supported + */ + hsflctl.regval = E1000_READ_FLASH_REG(hw, ICH_FLASH_HSFSTS)>>16; + + /* 0b/1b corresponds to 1 or 2 byte size, respectively. */ + hsflctl.hsf_ctrl.fldbcount = sizeof(u32) - 1; + hsflctl.hsf_ctrl.flcycle = ICH_CYCLE_READ; + /* In SPT, This register is in Lan memory space, not flash. + * Therefore, only 32 bit access is supported + */ + E1000_WRITE_FLASH_REG(hw, ICH_FLASH_HSFSTS, + (u32)hsflctl.regval << 16); + E1000_WRITE_FLASH_REG(hw, ICH_FLASH_FADDR, flash_linear_addr); + + ret_val = e1000_flash_cycle_ich8lan(hw, + ICH_FLASH_READ_COMMAND_TIMEOUT); + + /* Check if FCERR is set to 1, if set to 1, clear it + * and try the whole sequence a few more times, else + * read in (shift in) the Flash Data0, the order is + * least significant byte first msb to lsb + */ + if (ret_val == E1000_SUCCESS) { + *data = E1000_READ_FLASH_REG(hw, ICH_FLASH_FDATA0); + break; + } else { + /* If we've gotten here, then things are probably + * completely hosed, but if the error condition is + * detected, it won't hurt to give it another try... + * ICH_FLASH_CYCLE_REPEAT_COUNT times. + */ + hsfsts.regval = E1000_READ_FLASH_REG16(hw, + ICH_FLASH_HSFSTS); + if (hsfsts.hsf_status.flcerr) { + /* Repeat for some time before giving up. */ + continue; + } else if (!hsfsts.hsf_status.flcdone) { + DEBUGOUT("Timeout error - flash cycle did not complete.\n"); + break; + } + } + } while (count++ < ICH_FLASH_CYCLE_REPEAT_COUNT); + + return ret_val; +} +/** + * e1000_write_nvm_ich8lan - Write word(s) to the NVM + * @hw: pointer to the HW structure + * @offset: The offset (in bytes) of the word(s) to write. + * @words: Size of data to write in words + * @data: Pointer to the word(s) to write at offset. + * + * Writes a byte or word to the NVM using the flash access registers. + **/ +static s32 e1000_write_nvm_ich8lan(struct e1000_hw *hw, u16 offset, u16 words, + u16 *data) +{ + struct e1000_nvm_info *nvm = &hw->nvm; + struct e1000_dev_spec_ich8lan *dev_spec = &hw->dev_spec.ich8lan; + u16 i; + + DEBUGFUNC("e1000_write_nvm_ich8lan"); + + if ((offset >= nvm->word_size) || (words > nvm->word_size - offset) || + (words == 0)) { + DEBUGOUT("nvm parameter(s) out of bounds\n"); + return -E1000_ERR_NVM; + } + + nvm->ops.acquire(hw); + + for (i = 0; i < words; i++) { + dev_spec->shadow_ram[offset+i].modified = TRUE; + dev_spec->shadow_ram[offset+i].value = data[i]; + } nvm->ops.release(hw); @@ -3599,6 +3813,175 @@ } /** + * e1000_update_nvm_checksum_spt - Update the checksum for NVM + * @hw: pointer to the HW structure + * + * The NVM checksum is updated by calling the generic update_nvm_checksum, + * which writes the checksum to the shadow ram. The changes in the shadow + * ram are then committed to the EEPROM by processing each bank at a time + * checking for the modified bit and writing only the pending changes. + * After a successful commit, the shadow ram is cleared and is ready for + * future writes. + **/ +static s32 e1000_update_nvm_checksum_spt(struct e1000_hw *hw) +{ + struct e1000_nvm_info *nvm = &hw->nvm; + struct e1000_dev_spec_ich8lan *dev_spec = &hw->dev_spec.ich8lan; + u32 i, act_offset, new_bank_offset, old_bank_offset, bank; + s32 ret_val; + u32 dword = 0; + + DEBUGFUNC("e1000_update_nvm_checksum_spt"); + + ret_val = e1000_update_nvm_checksum_generic(hw); + if (ret_val) + goto out; + + if (nvm->type != e1000_nvm_flash_sw) + goto out; + + nvm->ops.acquire(hw); + + /* We're writing to the opposite bank so if we're on bank 1, + * write to bank 0 etc. We also need to erase the segment that + * is going to be written + */ + ret_val = e1000_valid_nvm_bank_detect_ich8lan(hw, &bank); + if (ret_val != E1000_SUCCESS) { + DEBUGOUT("Could not detect valid bank, assuming bank 0\n"); + bank = 0; + } + + if (bank == 0) { + new_bank_offset = nvm->flash_bank_size; + old_bank_offset = 0; + ret_val = e1000_erase_flash_bank_ich8lan(hw, 1); + if (ret_val) + goto release; + } else { + old_bank_offset = nvm->flash_bank_size; + new_bank_offset = 0; + ret_val = e1000_erase_flash_bank_ich8lan(hw, 0); + if (ret_val) + goto release; + } + for (i = 0; i < E1000_SHADOW_RAM_WORDS; i += 2) { + /* Determine whether to write the value stored + * in the other NVM bank or a modified value stored + * in the shadow RAM + */ + ret_val = e1000_read_flash_dword_ich8lan(hw, + i + old_bank_offset, + &dword); + + if (dev_spec->shadow_ram[i].modified) { + dword &= 0xffff0000; + dword |= (dev_spec->shadow_ram[i].value & 0xffff); + } + if (dev_spec->shadow_ram[i + 1].modified) { + dword &= 0x0000ffff; + dword |= ((dev_spec->shadow_ram[i + 1].value & 0xffff) + << 16); + } + if (ret_val) + break; + + /* If the word is 0x13, then make sure the signature bits + * (15:14) are 11b until the commit has completed. + * This will allow us to write 10b which indicates the + * signature is valid. We want to do this after the write + * has completed so that we don't mark the segment valid + * while the write is still in progress + */ + if (i == E1000_ICH_NVM_SIG_WORD - 1) + dword |= E1000_ICH_NVM_SIG_MASK << 16; + + /* Convert offset to bytes. */ + act_offset = (i + new_bank_offset) << 1; + + usec_delay(100); + + /* Write the data to the new bank. Offset in words*/ + act_offset = i + new_bank_offset; + ret_val = e1000_retry_write_flash_dword_ich8lan(hw, act_offset, + dword); + if (ret_val) + break; + } + + /* Don't bother writing the segment valid bits if sector + * programming failed. + */ + if (ret_val) { + DEBUGOUT("Flash commit failed.\n"); + goto release; + } + + /* Finally validate the new segment by setting bit 15:14 + * to 10b in word 0x13 , this can be done without an + * erase as well since these bits are 11 to start with + * and we need to change bit 14 to 0b + */ + act_offset = new_bank_offset + E1000_ICH_NVM_SIG_WORD; + + /*offset in words but we read dword*/ + --act_offset; + ret_val = e1000_read_flash_dword_ich8lan(hw, act_offset, &dword); + + if (ret_val) + goto release; + + dword &= 0xBFFFFFFF; + ret_val = e1000_retry_write_flash_dword_ich8lan(hw, act_offset, dword); + + if (ret_val) + goto release; + + /* And invalidate the previously valid segment by setting + * its signature word (0x13) high_byte to 0b. This can be + * done without an erase because flash erase sets all bits + * to 1's. We can write 1's to 0's without an erase + */ + act_offset = (old_bank_offset + E1000_ICH_NVM_SIG_WORD) * 2 + 1; + + /* offset in words but we read dword*/ + act_offset = old_bank_offset + E1000_ICH_NVM_SIG_WORD - 1; + ret_val = e1000_read_flash_dword_ich8lan(hw, act_offset, &dword); + + if (ret_val) + goto release; + + dword &= 0x00FFFFFF; + ret_val = e1000_retry_write_flash_dword_ich8lan(hw, act_offset, dword); + + if (ret_val) + goto release; + + /* Great! Everything worked, we can now clear the cached entries. */ + for (i = 0; i < E1000_SHADOW_RAM_WORDS; i++) { + dev_spec->shadow_ram[i].modified = FALSE; + dev_spec->shadow_ram[i].value = 0xFFFF; + } + +release: + nvm->ops.release(hw); + + /* Reload the EEPROM, or else modifications will not appear + * until after the next adapter reset. + */ + if (!ret_val) { + nvm->ops.reload(hw); + msec_delay(10); + } + +out: + if (ret_val) + DEBUGOUT1("NVM update error: %d\n", ret_val); + + return ret_val; +} + +/** * e1000_update_nvm_checksum_ich8lan - Update the checksum for NVM * @hw: pointer to the HW structure * @@ -3775,6 +4158,7 @@ */ switch (hw->mac.type) { case e1000_pch_lpt: + case e1000_pch_spt: word = NVM_COMPAT; valid_csum_mask = NVM_COMPAT_VALID_CSUM; break; @@ -3822,8 +4206,13 @@ DEBUGFUNC("e1000_write_ich8_data"); - if (size < 1 || size > 2 || offset > ICH_FLASH_LINEAR_ADDR_MASK) - return -E1000_ERR_NVM; + if (hw->mac.type == e1000_pch_spt) { + if (size != 4 || offset > ICH_FLASH_LINEAR_ADDR_MASK) + return -E1000_ERR_NVM; + } else { + if (size < 1 || size > 2 || offset > ICH_FLASH_LINEAR_ADDR_MASK) + return -E1000_ERR_NVM; + } flash_linear_addr = ((ICH_FLASH_LINEAR_ADDR_MASK & offset) + hw->nvm.flash_base_addr); @@ -3834,12 +4223,29 @@ ret_val = e1000_flash_cycle_init_ich8lan(hw); if (ret_val != E1000_SUCCESS) break; - hsflctl.regval = E1000_READ_FLASH_REG16(hw, ICH_FLASH_HSFCTL); + /* In SPT, This register is in Lan memory space, not + * flash. Therefore, only 32 bit access is supported + */ + if (hw->mac.type == e1000_pch_spt) + hsflctl.regval = + E1000_READ_FLASH_REG(hw, ICH_FLASH_HSFSTS)>>16; + else + hsflctl.regval = + E1000_READ_FLASH_REG16(hw, ICH_FLASH_HSFCTL); /* 0b/1b corresponds to 1 or 2 byte size, respectively. */ hsflctl.hsf_ctrl.fldbcount = size - 1; hsflctl.hsf_ctrl.flcycle = ICH_CYCLE_WRITE; - E1000_WRITE_FLASH_REG16(hw, ICH_FLASH_HSFCTL, hsflctl.regval); + /* In SPT, This register is in Lan memory space, + * not flash. Therefore, only 32 bit access is + * supported + */ + if (hw->mac.type == e1000_pch_spt) + E1000_WRITE_FLASH_REG(hw, ICH_FLASH_HSFSTS, + hsflctl.regval << 16); + else + E1000_WRITE_FLASH_REG16(hw, ICH_FLASH_HSFCTL, + hsflctl.regval); E1000_WRITE_FLASH_REG(hw, ICH_FLASH_FADDR, flash_linear_addr); @@ -3877,6 +4283,94 @@ return ret_val; } +/** +* e1000_write_flash_data32_ich8lan - Writes 4 bytes to the NVM +* @hw: pointer to the HW structure +* @offset: The offset (in bytes) of the dwords to read. +* @data: The 4 bytes to write to the NVM. +* +* Writes one/two/four bytes to the NVM using the flash access registers. +**/ +static s32 e1000_write_flash_data32_ich8lan(struct e1000_hw *hw, u32 offset, + u32 data) +{ + union ich8_hws_flash_status hsfsts; + union ich8_hws_flash_ctrl hsflctl; + u32 flash_linear_addr; + s32 ret_val; + u8 count = 0; + + DEBUGFUNC("e1000_write_flash_data32_ich8lan"); + + if (hw->mac.type == e1000_pch_spt) { + if (offset > ICH_FLASH_LINEAR_ADDR_MASK) + return -E1000_ERR_NVM; + } + flash_linear_addr = ((ICH_FLASH_LINEAR_ADDR_MASK & offset) + + hw->nvm.flash_base_addr); + do { + usec_delay(1); + /* Steps */ + ret_val = e1000_flash_cycle_init_ich8lan(hw); + if (ret_val != E1000_SUCCESS) + break; + + /* In SPT, This register is in Lan memory space, not + * flash. Therefore, only 32 bit access is supported + */ + if (hw->mac.type == e1000_pch_spt) + hsflctl.regval = E1000_READ_FLASH_REG(hw, + ICH_FLASH_HSFSTS) + >> 16; + else + hsflctl.regval = E1000_READ_FLASH_REG16(hw, + ICH_FLASH_HSFCTL); + + hsflctl.hsf_ctrl.fldbcount = sizeof(u32) - 1; + hsflctl.hsf_ctrl.flcycle = ICH_CYCLE_WRITE; + + /* In SPT, This register is in Lan memory space, + * not flash. Therefore, only 32 bit access is + * supported + */ + if (hw->mac.type == e1000_pch_spt) + E1000_WRITE_FLASH_REG(hw, ICH_FLASH_HSFSTS, + hsflctl.regval << 16); + else + E1000_WRITE_FLASH_REG16(hw, ICH_FLASH_HSFCTL, + hsflctl.regval); + + E1000_WRITE_FLASH_REG(hw, ICH_FLASH_FADDR, flash_linear_addr); + + E1000_WRITE_FLASH_REG(hw, ICH_FLASH_FDATA0, data); + + /* check if FCERR is set to 1 , if set to 1, clear it + * and try the whole sequence a few more times else done + */ + ret_val = e1000_flash_cycle_ich8lan(hw, + ICH_FLASH_WRITE_COMMAND_TIMEOUT); + + if (ret_val == E1000_SUCCESS) + break; + + /* If we're here, then things are most likely + * completely hosed, but if the error condition + * is detected, it won't hurt to give it another + * try...ICH_FLASH_CYCLE_REPEAT_COUNT times. + */ + hsfsts.regval = E1000_READ_FLASH_REG16(hw, ICH_FLASH_HSFSTS); + + if (hsfsts.hsf_status.flcerr) + /* Repeat for some time before giving up. */ + continue; + if (!hsfsts.hsf_status.flcdone) { + DEBUGOUT("Timeout error - flash cycle did not complete.\n"); + break; + } + } while (count++ < ICH_FLASH_CYCLE_REPEAT_COUNT); + + return ret_val; +} /** * e1000_write_flash_byte_ich8lan - Write a single byte to NVM @@ -3899,6 +4393,44 @@ /** +* e1000_retry_write_flash_dword_ich8lan - Writes a dword to NVM +* @hw: pointer to the HW structure +* @offset: The offset of the word to write. +* @dword: The dword to write to the NVM. +* +* Writes a single dword to the NVM using the flash access registers. +* Goes through a retry algorithm before giving up. +**/ +static s32 e1000_retry_write_flash_dword_ich8lan(struct e1000_hw *hw, + u32 offset, u32 dword) +{ + s32 ret_val; + u16 program_retries; + + DEBUGFUNC("e1000_retry_write_flash_dword_ich8lan"); + + /* Must convert word offset into bytes. */ + offset <<= 1; + + ret_val = e1000_write_flash_data32_ich8lan(hw, offset, dword); + + if (!ret_val) + return ret_val; + for (program_retries = 0; program_retries < 100; program_retries++) { + DEBUGOUT2("Retrying Byte %8.8X at offset %u\n", dword, offset); + usec_delay(100); + ret_val = e1000_write_flash_data32_ich8lan(hw, offset, dword); + if (ret_val == E1000_SUCCESS) + break; + } + if (program_retries == 100) + return -E1000_ERR_NVM; + + return E1000_SUCCESS; +} + + +/** * e1000_retry_write_flash_byte_ich8lan - Writes a single byte to NVM * @hw: pointer to the HW structure * @offset: The offset of the byte to write. @@ -4006,12 +4538,22 @@ /* Write a value 11 (block Erase) in Flash * Cycle field in hw flash control */ - hsflctl.regval = - E1000_READ_FLASH_REG16(hw, ICH_FLASH_HSFCTL); + if (hw->mac.type == e1000_pch_spt) + hsflctl.regval = + E1000_READ_FLASH_REG(hw, + ICH_FLASH_HSFSTS)>>16; + else + hsflctl.regval = + E1000_READ_FLASH_REG16(hw, + ICH_FLASH_HSFCTL); hsflctl.hsf_ctrl.flcycle = ICH_CYCLE_ERASE; - E1000_WRITE_FLASH_REG16(hw, ICH_FLASH_HSFCTL, - hsflctl.regval); + if (hw->mac.type == e1000_pch_spt) + E1000_WRITE_FLASH_REG(hw, ICH_FLASH_HSFSTS, + hsflctl.regval << 16); + else + E1000_WRITE_FLASH_REG16(hw, ICH_FLASH_HSFCTL, + hsflctl.regval); /* Write the last 24 bits of an index within the * block into Flash Linear address field in Flash @@ -4444,7 +4986,8 @@ E1000_WRITE_REG(hw, E1000_RFCTL, reg); /* Enable ECC on Lynxpoint */ - if (hw->mac.type == e1000_pch_lpt) { + if ((hw->mac.type == e1000_pch_lpt) || + (hw->mac.type == e1000_pch_spt)) { reg = E1000_READ_REG(hw, E1000_PBECCSTS); reg |= E1000_PBECCSTS_ECC_ENABLE; E1000_WRITE_REG(hw, E1000_PBECCSTS, reg); @@ -4876,7 +5419,8 @@ if ((device_id == E1000_DEV_ID_PCH_LPTLP_I218_LM) || (device_id == E1000_DEV_ID_PCH_LPTLP_I218_V) || (device_id == E1000_DEV_ID_PCH_I218_LM3) || - (device_id == E1000_DEV_ID_PCH_I218_V3)) { + (device_id == E1000_DEV_ID_PCH_I218_V3) || + (hw->mac.type == e1000_pch_spt)) { u32 fextnvm6 = E1000_READ_REG(hw, E1000_FEXTNVM6); E1000_WRITE_REG(hw, E1000_FEXTNVM6, @@ -4992,18 +5536,18 @@ * the PHY. * On i217, setup Intel Rapid Start Technology. **/ -void e1000_resume_workarounds_pchlan(struct e1000_hw *hw) +u32 e1000_resume_workarounds_pchlan(struct e1000_hw *hw) { s32 ret_val; DEBUGFUNC("e1000_resume_workarounds_pchlan"); if (hw->mac.type < e1000_pch2lan) - return; + return E1000_SUCCESS; ret_val = e1000_init_phy_workarounds_pchlan(hw); if (ret_val) { DEBUGOUT1("Failed to init PHY flow ret_val=%d\n", ret_val); - return; + return ret_val; } /* For i217 Intel Rapid Start Technology support when the system @@ -5017,7 +5561,7 @@ ret_val = hw->phy.ops.acquire(hw); if (ret_val) { DEBUGOUT("Failed to setup iRST\n"); - return; + return ret_val; } /* Clear Auto Enable LPI after link up */ @@ -5051,7 +5595,9 @@ if (ret_val) DEBUGOUT1("Error %d in resume workarounds\n", ret_val); hw->phy.ops.release(hw); + return ret_val; } + return E1000_SUCCESS; } /** Index: sys/dev/e1000/e1000_mac.h =================================================================== --- sys/dev/e1000/e1000_mac.h +++ sys/dev/e1000/e1000_mac.h @@ -36,9 +36,7 @@ #define _E1000_MAC_H_ void e1000_init_mac_ops_generic(struct e1000_hw *hw); -#ifndef E1000_REMOVED #define E1000_REMOVED(a) (0) -#endif /* E1000_REMOVED */ void e1000_null_mac_generic(struct e1000_hw *hw); s32 e1000_null_ops_generic(struct e1000_hw *hw); s32 e1000_null_link_info(struct e1000_hw *hw, u16 *s, u16 *d); @@ -46,7 +44,6 @@ void e1000_null_update_mc(struct e1000_hw *hw, u8 *h, u32 a); void e1000_null_write_vfta(struct e1000_hw *hw, u32 a, u32 b); int e1000_null_rar_set(struct e1000_hw *hw, u8 *h, u32 a); -s32 e1000_null_set_obff_timer(struct e1000_hw *hw, u32 a); s32 e1000_blink_led_generic(struct e1000_hw *hw); s32 e1000_check_for_copper_link_generic(struct e1000_hw *hw); s32 e1000_check_for_fiber_link_generic(struct e1000_hw *hw); Index: sys/dev/e1000/e1000_mac.c =================================================================== --- sys/dev/e1000/e1000_mac.c +++ sys/dev/e1000/e1000_mac.c @@ -70,7 +70,6 @@ mac->ops.setup_link = e1000_null_ops_generic; mac->ops.get_link_up_info = e1000_null_link_info; mac->ops.check_for_link = e1000_null_ops_generic; - mac->ops.set_obff_timer = e1000_null_set_obff_timer; /* Management */ mac->ops.check_mng_mode = e1000_null_mng_mode; /* VLAN, MC, etc. */ @@ -156,17 +155,6 @@ } /** - * e1000_null_set_obff_timer - No-op function, return 0 - * @hw: pointer to the HW structure - **/ -s32 e1000_null_set_obff_timer(struct e1000_hw E1000_UNUSEDARG *hw, - u32 E1000_UNUSEDARG a) -{ - DEBUGFUNC("e1000_null_set_obff_timer"); - return E1000_SUCCESS; -} - -/** * e1000_get_bus_info_pci_generic - Get PCI(x) bus information * @hw: pointer to the HW structure * Index: sys/dev/e1000/e1000_nvm.h =================================================================== --- sys/dev/e1000/e1000_nvm.h +++ sys/dev/e1000/e1000_nvm.h @@ -35,12 +35,26 @@ #ifndef _E1000_NVM_H_ #define _E1000_NVM_H_ -#if !defined(NO_READ_PBA_RAW) || !defined(NO_WRITE_PBA_RAW) struct e1000_pba { u16 word[2]; u16 *pba_block; }; -#endif + +struct e1000_fw_version { + u32 etrack_id; + u16 eep_major; + u16 eep_minor; + u16 eep_build; + + u8 invm_major; + u8 invm_minor; + u8 invm_img_type; + + bool or_valid; + u16 or_major; + u16 or_build; + u16 or_patch; +}; void e1000_init_nvm_ops_generic(struct e1000_hw *hw); @@ -52,6 +66,7 @@ s32 e1000_poll_eerd_eewr_done(struct e1000_hw *hw, int ee_reg); s32 e1000_read_mac_addr_generic(struct e1000_hw *hw); +s32 e1000_read_pba_num_generic(struct e1000_hw *hw, u32 *pba_num); s32 e1000_read_pba_string_generic(struct e1000_hw *hw, u8 *pba_num, u32 pba_num_size); s32 e1000_read_pba_length_generic(struct e1000_hw *hw, u32 *pba_num_size); @@ -76,6 +91,8 @@ s32 e1000_update_nvm_checksum_generic(struct e1000_hw *hw); void e1000_stop_nvm(struct e1000_hw *hw); void e1000_release_nvm_generic(struct e1000_hw *hw); +void e1000_get_fw_version(struct e1000_hw *hw, + struct e1000_fw_version *fw_vers); #define E1000_STM_OPCODE 0xDB00 Index: sys/dev/e1000/e1000_nvm.c =================================================================== --- sys/dev/e1000/e1000_nvm.c +++ sys/dev/e1000/e1000_nvm.c @@ -930,6 +930,41 @@ return E1000_SUCCESS; } +/** + * e1000_read_pba_num_generic - Read device part number + * @hw: pointer to the HW structure + * @pba_num: pointer to device part number + * + * Reads the product board assembly (PBA) number from the EEPROM and stores + * the value in pba_num. + **/ +s32 e1000_read_pba_num_generic(struct e1000_hw *hw, u32 *pba_num) +{ + s32 ret_val; + u16 nvm_data; + + DEBUGFUNC("e1000_read_pba_num_generic"); + + ret_val = hw->nvm.ops.read(hw, NVM_PBA_OFFSET_0, 1, &nvm_data); + if (ret_val) { + DEBUGOUT("NVM Read Error\n"); + return ret_val; + } else if (nvm_data == NVM_PBA_PTR_GUARD) { + DEBUGOUT("NVM Not Supported\n"); + return -E1000_NOT_IMPLEMENTED; + } + *pba_num = (u32)(nvm_data << 16); + + ret_val = hw->nvm.ops.read(hw, NVM_PBA_OFFSET_1, 1, &nvm_data); + if (ret_val) { + DEBUGOUT("NVM Read Error\n"); + return ret_val; + } + *pba_num |= nvm_data; + + return E1000_SUCCESS; +} + /** * e1000_read_pba_raw @@ -1232,4 +1267,115 @@ E1000_WRITE_FLUSH(hw); } +/** + * e1000_get_fw_version - Get firmware version information + * @hw: pointer to the HW structure + * @fw_vers: pointer to output version structure + * + * unsupported/not present features return 0 in version structure + **/ +void e1000_get_fw_version(struct e1000_hw *hw, struct e1000_fw_version *fw_vers) +{ + u16 eeprom_verh, eeprom_verl, etrack_test, fw_version; + u8 q, hval, rem, result; + u16 comb_verh, comb_verl, comb_offset; + + memset(fw_vers, 0, sizeof(struct e1000_fw_version)); + + /* basic eeprom version numbers, bits used vary by part and by tool + * used to create the nvm images */ + /* Check which data format we have */ + switch (hw->mac.type) { + case e1000_i211: + e1000_read_invm_version(hw, fw_vers); + return; + case e1000_82575: + case e1000_82576: + case e1000_82580: + hw->nvm.ops.read(hw, NVM_ETRACK_HIWORD, 1, &etrack_test); + /* Use this format, unless EETRACK ID exists, + * then use alternate format + */ + if ((etrack_test & NVM_MAJOR_MASK) != NVM_ETRACK_VALID) { + hw->nvm.ops.read(hw, NVM_VERSION, 1, &fw_version); + fw_vers->eep_major = (fw_version & NVM_MAJOR_MASK) + >> NVM_MAJOR_SHIFT; + fw_vers->eep_minor = (fw_version & NVM_MINOR_MASK) + >> NVM_MINOR_SHIFT; + fw_vers->eep_build = (fw_version & NVM_IMAGE_ID_MASK); + goto etrack_id; + } + break; + case e1000_i210: + if (!(e1000_get_flash_presence_i210(hw))) { + e1000_read_invm_version(hw, fw_vers); + return; + } + /* fall through */ + case e1000_i350: + hw->nvm.ops.read(hw, NVM_ETRACK_HIWORD, 1, &etrack_test); + /* find combo image version */ + hw->nvm.ops.read(hw, NVM_COMB_VER_PTR, 1, &comb_offset); + if ((comb_offset != 0x0) && + (comb_offset != NVM_VER_INVALID)) { + + hw->nvm.ops.read(hw, (NVM_COMB_VER_OFF + comb_offset + + 1), 1, &comb_verh); + hw->nvm.ops.read(hw, (NVM_COMB_VER_OFF + comb_offset), + 1, &comb_verl); + + /* get Option Rom version if it exists and is valid */ + if ((comb_verh && comb_verl) && + ((comb_verh != NVM_VER_INVALID) && + (comb_verl != NVM_VER_INVALID))) { + + fw_vers->or_valid = TRUE; + fw_vers->or_major = + comb_verl >> NVM_COMB_VER_SHFT; + fw_vers->or_build = + (comb_verl << NVM_COMB_VER_SHFT) + | (comb_verh >> NVM_COMB_VER_SHFT); + fw_vers->or_patch = + comb_verh & NVM_COMB_VER_MASK; + } + } + break; + default: + hw->nvm.ops.read(hw, NVM_ETRACK_HIWORD, 1, &etrack_test); + return; + } + hw->nvm.ops.read(hw, NVM_VERSION, 1, &fw_version); + fw_vers->eep_major = (fw_version & NVM_MAJOR_MASK) + >> NVM_MAJOR_SHIFT; + + /* check for old style version format in newer images*/ + if ((fw_version & NVM_NEW_DEC_MASK) == 0x0) { + eeprom_verl = (fw_version & NVM_COMB_VER_MASK); + } else { + eeprom_verl = (fw_version & NVM_MINOR_MASK) + >> NVM_MINOR_SHIFT; + } + /* Convert minor value to hex before assigning to output struct + * Val to be converted will not be higher than 99, per tool output + */ + q = eeprom_verl / NVM_HEX_CONV; + hval = q * NVM_HEX_TENS; + rem = eeprom_verl % NVM_HEX_CONV; + result = hval + rem; + fw_vers->eep_minor = result; + +etrack_id: + if ((etrack_test & NVM_MAJOR_MASK) == NVM_ETRACK_VALID) { + hw->nvm.ops.read(hw, NVM_ETRACK_WORD, 1, &eeprom_verl); + hw->nvm.ops.read(hw, (NVM_ETRACK_WORD + 1), 1, &eeprom_verh); + fw_vers->etrack_id = (eeprom_verh << NVM_ETRACK_SHIFT) + | eeprom_verl; + } else if ((etrack_test & NVM_ETRACK_VALID) == 0) { + hw->nvm.ops.read(hw, NVM_ETRACK_WORD, 1, &eeprom_verh); + hw->nvm.ops.read(hw, (NVM_ETRACK_WORD + 1), 1, &eeprom_verl); + fw_vers->etrack_id = (eeprom_verh << NVM_ETRACK_SHIFT) | + eeprom_verl; + } +} + Index: sys/dev/e1000/e1000_osdep.h =================================================================== --- sys/dev/e1000/e1000_osdep.h +++ sys/dev/e1000/e1000_osdep.h @@ -74,10 +74,6 @@ #define STATIC static #define FALSE 0 #define TRUE 1 -#ifndef __bool_true_false_are_defined -#define false FALSE -#define true TRUE -#endif #define CMD_MEM_WRT_INVALIDATE 0x0010 /* BIT_4 */ #define PCI_COMMAND_REGISTER PCIR_COMMAND @@ -99,9 +95,6 @@ typedef int32_t s32; typedef int16_t s16; typedef int8_t s8; -#ifndef __bool_true_false_are_defined -typedef boolean_t bool; -#endif #define __le16 u16 #define __le32 u32 Index: sys/dev/e1000/e1000_phy.c =================================================================== --- sys/dev/e1000/e1000_phy.c +++ sys/dev/e1000/e1000_phy.c @@ -1827,9 +1827,9 @@ phy_data); if (ret_val) return ret_val; - } - DEBUGOUT1("M88E1000 PSCR: %X\n", phy_data); + DEBUGOUT1("M88E1000 PSCR: %X\n", phy_data); + } ret_val = phy->ops.read_reg(hw, PHY_CONTROL, &phy_data); if (ret_val) Index: sys/dev/e1000/e1000_regs.h =================================================================== --- sys/dev/e1000/e1000_regs.h +++ sys/dev/e1000/e1000_regs.h @@ -65,6 +65,9 @@ #define E1000_FEXTNVM4 0x00024 /* Future Extended NVM 4 - RW */ #define E1000_FEXTNVM6 0x00010 /* Future Extended NVM 6 - RW */ #define E1000_FEXTNVM7 0x000E4 /* Future Extended NVM 7 - RW */ +#define E1000_FEXTNVM9 0x5BB4 /* Future Extended NVM 9 - RW */ +#define E1000_FEXTNVM11 0x5BBC /* Future Extended NVM 11 - RW */ +#define E1000_PCIEANACFG 0x00F18 /* PCIE Analog Config */ #define E1000_FCT 0x00030 /* Flow Control Type - RW */ #define E1000_CONNSW 0x00034 /* Copper/Fiber switch control - RW */ #define E1000_VET 0x00038 /* VLAN Ether Type - RW */ @@ -107,6 +110,7 @@ #define E1000_PBA 0x01000 /* Packet Buffer Allocation - RW */ #define E1000_PBS 0x01008 /* Packet Buffer Size */ #define E1000_PBECCSTS 0x0100C /* Packet Buffer ECC Status - RW */ +#define E1000_IOSFPC 0x00F28 /* TX corrupted data */ #define E1000_EEMNGCTL 0x01010 /* MNG EEprom Control */ #define E1000_EEARBC 0x01024 /* EEPROM Auto Read Bus Control */ #define E1000_EEARBC_I210 0x12024 /* EEPROM Auto Read Bus Control */ @@ -588,6 +592,10 @@ #define E1000_TIMADJL 0x0B60C /* Time sync time adjustment offset Low - RW */ #define E1000_TIMADJH 0x0B610 /* Time sync time adjustment offset High - RW */ #define E1000_TSAUXC 0x0B640 /* Timesync Auxiliary Control register */ +#define E1000_SYSSTMPL 0x0B648 /* HH Timesync system stamp low register */ +#define E1000_SYSSTMPH 0x0B64C /* HH Timesync system stamp hi register */ +#define E1000_PLTSTMPL 0x0B640 /* HH Timesync platform stamp low register */ +#define E1000_PLTSTMPH 0x0B644 /* HH Timesync platform stamp hi register */ #define E1000_SYSTIMR 0x0B6F8 /* System time register Residue */ #define E1000_TSICR 0x0B66C /* Interrupt Cause Register */ #define E1000_TSIM 0x0B674 /* Interrupt Mask Register */ @@ -680,7 +688,6 @@ #define E1000_O2BGPTC 0x08FE4 /* OS2BMC packets received by BMC */ #define E1000_O2BSPC 0x0415C /* OS2BMC packets transmitted by host */ -#define E1000_DOBFFCTL 0x3F24 /* DMA OBFF Control Register */ #endif Index: sys/dev/e1000/if_igb.c =================================================================== --- sys/dev/e1000/if_igb.c +++ sys/dev/e1000/if_igb.c @@ -614,9 +614,9 @@ "Disable Energy Efficient Ethernet"); if (adapter->hw.phy.media_type == e1000_media_type_copper) { if (adapter->hw.mac.type == e1000_i354) - e1000_set_eee_i354(&adapter->hw); + e1000_set_eee_i354(&adapter->hw, TRUE, TRUE); else - e1000_set_eee_i350(&adapter->hw); + e1000_set_eee_i350(&adapter->hw, TRUE, TRUE); } } @@ -1403,9 +1403,9 @@ /* Set Energy Efficient Ethernet */ if (adapter->hw.phy.media_type == e1000_media_type_copper) { if (adapter->hw.mac.type == e1000_i354) - e1000_set_eee_i354(&adapter->hw); + e1000_set_eee_i354(&adapter->hw, TRUE, TRUE); else - e1000_set_eee_i350(&adapter->hw); + e1000_set_eee_i350(&adapter->hw, TRUE, TRUE); } }