Index: bhyve/bhyve.8
===================================================================
--- bhyve/bhyve.8
+++ bhyve/bhyve.8
@@ -24,7 +24,7 @@
 .\"
 .\" $FreeBSD$
 .\"
-.Dd February 27, 2017
+.Dd March 15, 2017
 .Dt BHYVE 8
 .Os
 .Sh NAME
@@ -49,10 +49,13 @@
 Parameters such as the number of virtual CPUs, amount of guest memory, and
 I/O connectivity can be specified with command-line parameters.
 .Pp
-The guest operating system must be loaded with
+If not using boot ROM, the guest operating system must be loaded with
 .Xr bhyveload 8
 or a similar boot loader before running
-.Nm .
+.Nm ,
+otherwise it is enough to run
+.Nm
+with a boot ROM of choice.
 .Pp
 .Nm
 runs until the guest operating system reboots or an unhandled hypervisor
@@ -188,6 +191,10 @@
 .It Li lpc
 LPC PCI-ISA bridge with COM1 and COM2 16550 serial ports and a boot ROM.
 The LPC bridge emulation can only be configured on bus 0.
+.It Li fbuf
+Framebuffer device.
+.It Li xhci
+eXtensible Host Controller Interface (xHCI) USB controller.
 .El
 .It Op Ar conf
 This optional parameter describes the backend for device emulations.
@@ -299,6 +306,34 @@
 Emergency write is advertised, but no-op as of now.
 .El
 .El
+.Pp
+Framebuffer devices:
+.Bl -tag -width 10n
+.It tcp= Ns Ar host:port Ns Op , Ns w= Ns Ar width Ns ,h= Ns Ar height Ns Op , Ns wait
+.Bl -tag -width 8n
+.It Ar host:port
+A
+.Ar host
+and a
+.Ar port
+VNC should listen on.
+.It Ar width No and Ar height
+A display resolution, width and height, respectively.
+.It wait
+Instruct
+.Nm
+to only boot upon the initiation of a VNC connection, simplifying the installation
+of operating systems that require immediate keyboard input.
+This can be removed for post-installation use.
+.El
+.El
+.Pp
+xHCI USB devices:
+.Bl -tag -width 10n
+.It Li tablet
+A USB tablet device which provides precise cursor synchronization
+when using VNC.
+.El
 .El
 .It Fl S
 Wire guest memory.
@@ -347,11 +382,12 @@
 triple fault
 .El
 .Sh EXAMPLES
-The guest operating system must have been loaded with
+If not using boot ROM, the guest operating system must have been loaded with
 .Xr bhyveload 8
 or a similar boot loader before
 .Xr bhyve 4
 can be run.
+Otherwise boot loader is not needed.
 .Pp
 To run a virtual machine with 1GB of memory, two virtual CPUs, a virtio
 block device backed by the
@@ -389,6 +425,21 @@
   -l com1,/dev/nmdm0A \\
   -A -H -P -m 8G
 .Ed
+.Pp
+Run an UEFI virtual machine with a display resolution of 800 by 600 pixels
+that can be accessed via VNC at: 0.0.0.0:5900.
+.Bd -literal -offset indent
+bhyve -c 2 -m 4G -w -H \\
+  -s 0,hostbridge \\
+  -s 3,ahci-cd,/path/to/uefi-OS-install.iso \\
+  -s 4,ahci-hd,disk.img \\
+  -s 5,virtio-net,tap0 \\
+  -s 29,fbuf,tcp=0.0.0.0:5900,w=800,h=600,wait \\
+  -s 30,xhci,tablet \\
+  -s 31,lpc -l com1,stdio \\
+  -l bootrom,/usr/local/share/uefi-firmware/BHYVE_UEFI.fd \\
+   uefivm
+.Ed
 .Sh SEE ALSO
 .Xr bhyve 4 ,
 .Xr nmdm 4 ,